Technical Note - Partially Fluxed Pellets With Low Silica For Blast Furnace At Samarco Mineração S.A.

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]