Search Documents

By Claudio Cesar da Costar

O Alto Forno 1 da ArcelorMittal Tubarão, operou entre 30 de novembro de 1983 e 18 de abril de 2012, produzindo 93.915 Mt. Durante esta campanha, inúmeras melhorias foram implementadas para aumentar sua longevidade mantendo o volume e custo de produção. O Alto Forno 1 da AMT é reconhecido como recordista tanto em volume de produção quanto em tempo de operação para uma única campanha. Durante sua reforma, foram empregadas as técnicas de reforma em grandes blocos, as quais foram trocados todo o cadinho, corpo e topo do Alto Forno, trazendo recursos tecnológicos possibilitando obter melhores resultados durante a segunda campanha. Após a reforma, o Alto Forno 1 continua apresentando bons resultados em termos de produtividade, consumo de combustíveis e índices de trabalho, colocando-o entre um dos Altos Fornos com melhores resultados do grupo ArcelorMittal.

Aug 16, 2017

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Andrea Zanon

Slitting processes have been used for many years to increase the productivity of smaller diameter deformed bars, without making major investments in the rolling mill. This technology is used mainly for the production of reinforcing bars (7-20 mm diameter), but successful applications exist also for round bar production. The multi-slitting process enables to produce up to 5 bars starting from one billet, thus increasing the productivity of the smaller products. Danieli Morgårdshammar, world leader in the supply of rolling mills for long products, has been a front-runner in slitting technology since its first applications and has recently developed, first in the world, the technology to produce 5X8mm rebar. This process has been recently applied in BRSM steel, a company based in Bangladesh which is a worldwide benchmark for slitting technology performances. This paper presents the necessary modifications which need to be considered when developing a 5-strand slitting project (and multi-strand slitting projects in general), as well as the results obtained at BSRM Steel when the process was implemented in 2016, the first rolling mill in the world rolling 5X8 mm slit rebars.

Oct 30, 2017

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Ronaldo Santos Sampaio

This paper call attention to increasing ratio of oxygen depletion from atmosphere besides the global worries about CO2 concentration increase in the atmosphere. It highlights the big mistake in considering Carbon Capture and Storage, CCS, as a way to reduce the increasing concentration of CO2 in the atmosphere. As a hypothetical example it presents an existing pseudo-ecosystem of manufacturing that has real windows of opportunity to increase its share in the global materials production industry, even in highly industrialized countries. As a suggestion and example the author point out possibilities to almost fulfill the proposed simple rules to be considered inside an ecosystem of manufacturing utilizing the production of steel via biomass versus fossil coal. A relevant and difficult rule to be attained in a quasi-ecosystem of manufacture is to be a near zero atmosphere oxygen depletion integrated process. The industrial alternatives that utilizes the actual photosynthesis are the ones that can reach a higher ecosystem of manufacture’s index. It is presented an ideal integrated steelmaking process where the gaseous, liquids and solid residues generated in one part of the system are or can be utilized in the other parts of the same system. A potential ecosystem of manufacture to produce primary iron is illustrated in the paper.

Aug 17, 2017

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Izabelle Lannes Salgueiro Ferreira

O presente trabalho teve como objetivo adequar às propriedades mecânicas dos perfis ASTM A572 G60, através do estudo da influência dos parâmetros de processo de laminação e composição química do aço. Os perfis ASTM A572 G60, são utilizados nas indústrias de fabricação de torres de transmissão. A metodologia utilizada neste trabalho foi o desenvolvimento de um modelamento matemático, com base na ferramenta estatística de Análise de Regressão Múltipla. Através desta ferramenta foi possível obter previsibilidade de processo e identificar os parâmetros mais influentes nas propriedades mecânicas dos perfis ASTM A572 G60, o que possibilitou a determinação da composição química ideal do aço e os melhores parâmetros de processo de laminação.

Jul 30, 2018

By Osvaldo Guilherme Comineli

While the hot cracking of Cu-containing steels is a serious and widely known problem for the industry, the literature reports that copper only slightly impairs the hot-ductility measured in laboratory. A distinction is drawn between hot ductility and hot shortness and the respective cracking operating mechanism involved at the respective range of temperature. The representability of the laboratory assessment of hot cracking of Cu-containing steels by hot tensile tests compared with actual results in industrial practice is discussed. The effectiveness of the variable affecting in each cracking mechanism and respective temperature range, focused in improving the hot cracking assessment of Cu-steels and the relative importance of oxidation will also be discussed. It is concluded that the hot tensile test in argon might be a good simulation if properly interpreted and that the role of oxidation is secondary in causing hot shortness. A schematic diagram for the hot tensile test is proposed.

Oct 30, 2017

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Paulo Conceição, Carlos Sampaio, Carlos Petter, Ariane Kuerten

The Sensor Based-Sorting technology is an emerging technology applied in mineral separation and concentration. The technique consists in using a method known as Dual Energy X-ray Transmission sorting (DE-XRT). The particle's position over the conveyor belt was evaluated and, despite de variability of results, shows that there is no a position with greater accuracy on the sensor's reading. Results obtained indicated that DE-XRT sorting technology was able to significantly reduce the mass and the ash content of the ore feed, being an interesting option for reduction of costs and improvement of coal quality in beneficiation plants.

Oct 3, 2019

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Leopoldo José Naves Alves

Os sistemas de controle e supervisão de processos que não contemplam o adequado gerenciamento de alarmes e eventos sofrem uma sobrecarga na operação com um número exacerbado de informações durante situações de distúrbio e até mesmo operação normal. Nos últimos anos, a abordagem sobre metodologia, boas práticas e planejamento adequado do gerenciamento de alarmes vem sendo alvo de crescente interesse, seu objetivo é garantir um ótimo estado de produção e uma maior segurança dos equipamentos e dos operadores. Em 2009 a ISA, após anos de trabalho sobre este tema, apresentou a norma ANSI/ISA 18.2, formalizando conceitos, definindo metodologias e sugerindo boas práticas. Este trabalho visa apresentar de maneira objetiva tal norma e demonstrar a viabilidade e eficiência de sua aplicação pratica.

Aug 8, 2018

By William Roger Carvalho Gomes

Frequentemente surgem discussões sobre a utilização de tecnologias mais limpas em todos os segmentos de mercado. A indústria de transformação por estar relacionada ao aumento crescente na geração de resíduos sólidos. Atualmente, toma como necessária ter um foco importante na busca pelo desenvolvimento sustentável. Este trabalho tem como objetivo comparar dois materiais, sendo a fibra de vidro e a fibra de Basalto tendo como base a análise do ciclo de vida (ACV), por meio das análises do inventário e dos impactos. De acordo com os dados obtidos estima-se que o gasto energético para produção da fibra de vidro é aproximadamente 3 vezes maior que a fibra de basalto. Segundo a participação percentual da produção das fibras nos impactos ambientais, a fibra de basalto apresenta os melhores indicadores positivos em relação à fibra de vidro. Como análise preliminar o objetivo deste trabalho foi alcançado, apresentando que os impactos gerados pela fibra de basalto são menores que as da fibra de vidro.

Aug 17, 2017

By Vinícius da Silva Madruga

Os processos de lingotamento contínuo e de lingotamento convencional apresentam diferenças na solidificação dos aços, esse fato tem impacto na distribuição, quantidade e forma de inclusões de óxidos e sulfetos. O objetivo desse trabalho é verificar de que maneira tais diferenças influenciam na distribuição dos sulfetos ao longo do aço solidificado de qualidade SAE 1050. Para isso, 20 amostras foram retiradas de eixos forjados e barras laminadas, produtos conformados de origem do lingotamento convencional e do lingotamento contínuo, respectivamente. As amostras foram analisadas em microscópio ótico e microscópio eletrônico de varredura no modo de análise automatizada de partículas. Através das imagens e de dados numéricos obtidos, foi visto que nas amostras de barra laminada há grande quantidade de sulfetos, se analisada na seção longitudinal, em relação às amostras de eixo forjado. Analisando na seção transversal, foram detectados menos sulfetos devido ao alinhamento dos mesmos. Entre as amostras de eixo forjado, a área ocupada pelos sulfetos é maior no pé do lingote, reduzindo em direção à cabeça, apesar de a cabeça apresentar mais sulfetos. Tais diferenças foram atribuídas à taxa de resfriamento, à seção transversal do produto e ao processo, que variam entre os dois tipos de lingotamento.

Oct 30, 2017

By Luana de Sousa Santos

O setor Petróleo e Gás Natural vem tendo enormes gastos com as paradas de manutenção. Estes gastos estão relacionados à degradação sofrida por seus equipamentos de refino devido à corrosão. Uma possível solução seria a utilização de novas ligas de aço inoxidável ferrítico com elevados percentuais de molibdênio, o que teoricamente favoreceria um aumento da resistência à corrosão. No entanto, pelo fato dessas ligas serem aplicadas na condição como soldada mudanças microestruturais significativas podem ser geradas, além de considerar o fato da solda das ligas em estudo ser realizada com material dissimilar, e a diferença existente entre o metal de adição e a região afetada pelo calor (ZAC) pode propiciar ao surgimento do fenômeno eletroquímico conhecido como pilha galvânica. Portanto, o objetivo deste trabalho foi analisar o comportamento corrosivo na solda dissimilar de duas novas ligas de aço inoxidável ferrítico com diferentes teores de cromo e um elevado teor de molibdênio, ambas com adição de superliga de níquel, verificando a influência da pilha. O resultado da soldagem foi avaliado através de exames metalográficos e ensaios eletroquímicos. As micrografias do metal de adição utilizado na soldagem das ligas mostraram que o mesmo possui uma microestrutura dendrítica e os gráficos obtidos dos ensaios de Polarização Potenciodinâmica Cíclica não reproduziram para as ligas soldadas, o que foi melhor analisado observando os resultados dos ensaios de forma separada, para as regiões que constituem a solda das ligas, o metal de adição e ZAC. Sendo possível verificar a existência de uma maior resistência a corrosão no metal de adição.

Aug 8, 2018

By Nestor Ferreira Carvalho

Com o intuito de garantir a segurança das pessoas, meio ambiente e o patrimônio das empresas, os vasos de pressão e caldeiras instalados no Brasil devem ser protegidos por válvulas de segurança, cuja função é evitar que o equipamento seja pressurizado acima da pressão de projeto. A escolha do melhor local para instalação dessas válvulas deve levar em consideração, além dos itens usuais de projeto, os esforços gerados quando da abertura dessas válvulas. Esse artigo, faz uma análise da fratura, com o propósito de determinar as causas básicas da falha e evitar sua repetição. A análise foi realizada com o apoio de literaturas sobre fractografia e fadiga.

Aug 16, 2017

By ALESSANDRA SAVAZZINI REIS

A crescente preocupação em relação à sustentabilidade ambiental no setor de cerâmica vermelha associada ao alto consumo de argila, leva à busca de alternativas de incorporação de resíduos na massa argilosa. Com isso, vê-se a necessidade de caracterizar resíduos usados em cerâmica vermelha. As olarias brasileiras consomem cerca de 10 milhões de toneladas de argila ao mês para produção de telhas e blocos. O resíduo da indústria de rocha ornamental e a lama de alto forno podem se tornar passivos ambientais caso não sejam reaproveitados. O objetivo deste trabalho visa caracterizar e avaliar as propriedades cerâmicas em massas argilosas contendo resíduo de rocha e lama de alto forno. Os resíduos foram caracterizados por meio de ensaios de FRX, DRX, limites de Atterberg e granulometria. Massas argilosas com resíduos em teores variando de 5% a 50% (massa) foram conformadas, queimadas em forno industrial na olaria à 850ºC para verificação de: absorção de água, porosidade, massa específica aparente, e resistência mecânica. Os resultados mostram que a massa argilosa com o resíduo de rocha no teor de 50% apresentou os melhores valores das propriedades cerâmicas analisadas e maior resistência mecânica, tais melhorias também foram verificadas na massa argilosa com lama de alto forno no teor de 5%.

Oct 30, 2017