Search Documents

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017

By Abraão Santos Silva

Juntas soldadas são regiões críticas quanto a fraturas. Neste estudo foi analisada a tenacidade à fratura de soldas de reparo de tubos de mastros de sonda de perfuração de petróleo. Foram escolhidos os tubos principais de sustentação dos mastros. Seções do mastro são corriqueiramente reparados por soldagem TIG de raiz e preenchimento por eletrodo revestido. Estes processos provocam modificações metalúrgicas na zona termicamente afetada da solda, o que pode ter reflexo na tenacidade à fratura dos tubos. Foram produzidos corpos de prova para medir a tenacidade à fratura do metal base e da zona afetada termicamente. Os resultados indicaram que não houve redução de tenacidade a fratura devido as alterações microestruturais da zona afetada e isto foi associado ao procedimento de soldagem multipasses utilizado.

Aug 16, 2017

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Joshua Alyson Freitas Ribeiro

Aços com teores eutetóides, tratados termicamente são usualmente utilizados em trilhos metroviários. Para que sejam atingidas as propriedades mecânicas desejadas para as devidas aplicações, o material pode ser submetido a alguns tratamentos térmicos, como, por exemplo, Recozimento Pleno, Normalização e Têmpera. Os tratamentos térmicos são de extrema importância, pois possibilitam uma grande versatilidade na utilização dos aços em geral. Neste estudo, as peças utilizadas são provenientes de um trilho metroviário e foram fornecidas pelo Laboratório de Pesquisa e Tecnologia em Soldagem da Universidade Federal do Ceará. Foram feitas análises metalográficas após diferentes tratamentos térmicos em peças do Aço SAE 1080 Fe-C com o objetivo de verificar os aspectos microestruturais e a sua inflências no comportamento mecânico das amostras e a alteração nas propriedades mecânicas. Pelo fato do material estudado ter uma matriz com composição perlítica de, aproximadamente, 100%, são mostradas as consequências devido à mudança nos espaçamentos interlamelares provocados pela aplicação de diferentes tratamentos e a influência da fase martensita na dureza do material.

Oct 30, 2017

By Andreas Volkert

Energy efficiency, equipment reliability and cost reduction are of the key factors in any efficient plant. Badische Stahlwerke (BSW) started using its own burner technology in 2001, this was developed by Badische Stahl-Engineering (BSE). Over the past 15 years, Badische improved all aspects of its Virtual Lance Burner (VLB), to perfectly fit all steelmaking requirements. This tiltable VLB was first tested at BSW’s electric arc furnace no. 2 in 2012. Promising results like reduction of refractory wear, energy efficiency, reliability, etc., were obtained. At the same time the existing VLB system was further improved with regards to the design of the water-cooled copper box. Today in 2016 both EAFs at BSW are equipped with the new patented tiltable system and the new copper box design. The paper will describe the results of the past years at Badische, but will also show the performance at other installations.

Aug 17, 2017

By Patrick Tassot

Increased worldwide highly competition in steel market imposes innovative measure for the steelmaker targeting cost reduction and climate-friendly steelmaking process in order to have the ability to withstand the pressure of the market. At the same time the demand for high purity and highest quality steels continues to grow from year to year, especially in the sector automotive in transportation of oil and gas, in the construction Industry and in the manufacture of heavy plate. As they allow producers to be up to the requirements while allowing expanding their product mix, new secondary metallurgical treatments have become a must additionally to standard equipment elements of steel plants modern. Most of these treatments occurs in the steel ladle increasing the pressure to ensure a reliable and as possible neutral reactor. Intelligent solutions for refractory lining ladles should integrate better adaptation to the operational process parameters and the high reliability/availability at the best cost/performance. This challenge has conducted Refratechnik to develop new concepts to overcome the frontier between shaped and unshaped materials and that’s what will be covered in this paper.

Aug 17, 2017

By Tiago Fernando de Abreu e Silva Tomanik

Massa plástica refratária e placas isolantes têm sido utilizadas por um longo período em Fornos de Reaquecimento de Placas e Tarugos na Indústria Siderúrgica. Novas tecnologias para o revestimento refratário tem ganhado crescente interesse nos últimos anos em função da redução no consumo de combustíveis, redução em tempo e custos de manutenção e, consequentemente aumento de produtividade. Esse trabalho apresenta o desenvolvimento de um novo concreto isolante, de aplicação por projeção, para condições de alta temperatura, que permitiu a substituição do concreto denso na face de trabalho. Essa nova tecnologia permitiu uma redução no tempo de reparo e alta confiabilidade, pois suporta muito bem as agressivas condições da atmosfera do forno. Também será discutido o futuro desenvolvimento de projetos com significantes economias em energia.

Oct 30, 2017

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By Thomas Höfler, Michael Auinger, Bernhard Linder

Gas-fired pusher furnaces are commonly used to heat steel slabs before hot rolling. Temperatures well above 1000 °C combined with an oxidizing atmosphere containing H2O, CO2 and O2 result in rapid oxidation of most steel grades. The resulting oxide scale and the chemistry of the metal-scale-interface are major determining factors for the occurrence of hot rolling defects. To better understand these phenomena, lab-scale trials were performed with two different steel grades in an electric tube furnace in the temperature range 1000-1250 °C, using an atmosphere of about 20 % H2O, 7 % CO2 and 3 % O2. Humidification of the gas was achieved by evaporation, using a custom thermostat with standard laboratory glassware. The resulting samples were prepared metallographically, using cold mounting under vacuum with taper section angles, and analyzed using light microscopy and SEM/EDS. The scale structure of the Si alloyed steel was highly dependent on the oxidation temperature due to the formation of eutectic liquid phases of FeO, Fe2SiO4 and FeAl2O4. Below the eutectic temperature, the scale of the Si steel appeared to be made up of three distinct areas: The external scale consisting solely of Fe oxides, the internal scale containing Fe2SiO4 and FeAl2O4, and an internal oxidation zone with SiO2 and Al2O3 in a mostly plain Fe matrix. Comparisons of the experimental results with simulations of the internal oxidation showed good qualitative agreement.

Oct 1, 2019

By Arnaldo Forgas Júnior

Three techniques for ferrite quantification were applied in a duplex stainless steel UNS S31803 solution treated at three different temperatures, 1000, 1100 and 1200°C, in order to verify their compliance with the results from ThermoCalc® prediction. It is verified that only austenite and ferrite phases are present in the samples and that an increasing in solution treatment temperature led to the increase of the volume fraction of ferrite. It is also observed that quantitative stereology technique shows absolute values closer to ThermoCalc® predictions. On the other hand, measurements by ferritoscope and XRD show significant deviations, probably due to texturing effect imposed by the rolling process.

Aug 16, 2017

By Douglas Martinazzi

O processo de soldagem por fricção com pino consumível (Friction Hydro-Pillar Processing- FHPP) um método de reparo no estado sólido que consiste no processamento termomecânico de um pino metálico em alta rotação e inserido em um orifício criado no material a reparar. O pino é pressionado com uma força axial e o aquecimento resultante do atrito dos materiais é suficiente para garantir a plastificação dos mesmos promovendo o preenchimento do orifício e a união dos componentes. Este trabalho é centrado na análise da distribuição de inclusões não metálicas do tipo Sulfetos de Manganês (MnS) presentes em juntas soldadas produzidas por esta técnica com a aplicação de diferentes forças axiais. Micrografias da zona termomecanicamente afetada (ZTMA) foram realizadas por microscopia ótica em amostras polidas e sem ataque para registrar as inclusões. Essas micrografias foram avaliadas via análise de imagens visando a determinação de quantidade, tamanho e área ocupada pelas inclusões nas juntas em juntas soldadas. O mapeamento identificou a distribuição e o tamanho médio das inclusões em função das forças axiais. Concluiu-se que a região analisada é potencialmente crítica no que diz respeito a tenacidade à fratura, uma vez que foi observada uma quantidade considerável de inclusões fragmentadas de dimensões reduzidas.

Aug 7, 2018

By Adriano de Assunção Rodrigues, Gustavo Henrique Pinto de Oliveira, Wemerson Junio Gandra

O processo de obtenção de coque em uma coqueria convencional Non-Recovery consiste no aquecimento de uma mistura de carvões, provocando sua desvolatilização, gerando o coque que é principal combustível utilizado em altos-fornos. O aquecimento da mistura de carvões se dá de forma indireta. As paredes dos fornos recebem calor da câmara de combustão alimentada por uma mistura de gases de alto-forno, coqueria e aciaria ou, exclusivamente pelo gás de coqueria. O gás de coqueria COG (coke oven gas) é composto basicamente de hidrocarbonetos e recebe tratamento para retirada de impurezas, alcatrão, sulfato de amônia e óleos leves. Os elementos residuais no gás, mesmo após o processo de tratamento são extremamente prejudiciais às tubulações de distribuição, formando compostos corrosivos, podendo ocasionar o colapso de tubulações, gerando acidentes, gastos com reparos e perda de produção. Neste contexto, o presente trabalho tem por objetivo apresentar os fatores que levaram a necessidade de substituição das tubulações principais de distribuição de gás no subsolo da Coqueria 3 da Usiminas Ipatinga, conferindo segurança ao processo e estabilidade operacional.

Oct 1, 2019

By Wagner Duarte Flores

A demanda por tubos de aço com rigorosos requisitos de propriedades mecânicas tem crescido devido à exploração de reservas de petróleo e gás natural em regiões remotas e em ambientes hostis. Um grande desafio para as siderúrgicas é prever as alterações de propriedades mecânicas que ocorrem durante a conformação chapa/tubo, associadas ao encruamento e ao efeito Bauschinger, visando atender às especificações no tubo. Nesse estudo, foi avaliado o efeito da conformação chapa/tubo nas propriedades mecânicas do aço API X60 (TMCP). Para tal, foram realizados ensaios de tração, de impacto Charpy e de CTOD, em amostras de chapa e de tubo, e análise metalográfica, além de simulação do efeito Bauschinger por meio de ensaio cíclico compressão-tração. Os resultados dos ensaios de tração, tanto com os corpos de prova plate type quanto com round bar, apresentaram aumento da tensão limite de escoamento e redução da ductilidade, devido ao encruamento. Nos corpos de prova que sofreram aplainamento, esse aumento foi menos pronunciado, justificado pela ocorrência do efeito Bauschinger. A simulação do efeito Bauschinger confirmou a indicação de queda do limite de escoamento devido ao ciclo reverso de deformação. A tenacidade não foi fortemente afetada após a conformação do tubo.

Aug 16, 2017

By Nicola Santangelo

The current economic crisis and growing environmental issues have led the steel industry to face the simultaneous effects of low demand and production overcapacity in a globalized steel market, whilst confronting high energy prices and the need to comply with the green economy. Heat Recovery from waste gas of the Electric Arc Furnace (EAF) represents one of the greatest opportunities to reduce the consumption of primary energy and reduce the CO2 emissions in steel industry. The heat of the off-gas, if recovered and converted into electrical power, can make the whole Fumes Treatment Plant autonomous from the electric point of view, thus making it a “Zero-Energy FTP”. The concept is to substitute the Cooling Components (Water Cooled Panels and Air Cooler) are substituted with Heat Recovery Components (Hot Water Cooled Panels and Heat Exchanger). The recovered heat can be converted into power by using an Organic Rankine Cycle (ORC) turbine. The heat recovered by the HWCP and the Heat Exchanger is characterized by a variable thermal power, which affects the efficiency of the downstream ORC System. Danieli, in collaboration with the University of Udine, has developed the Thermal Stabilizer Unit (TSU). Danieli has realized the first step towards Zero Energy FTP at ABS steelmaking plant (Italy) by installing a CHR® - Clean Heat Recovery. This plant has been started up on 17th October 2014. The HMI of the CHR® is integrated in the HMI of the furnace, so all the process could be kept under control by the furnace operator. At ABS recovered thermal power reaches 5.5 MW. The max power production reached with CHR plant in ABS (over 1MW of electric power) consents an annual saving of approx. 500,000 EUR.

Aug 16, 2017

By Roberto Silva de Andrade

O inchamento é um grande problema durante a redução de pelotas de minério de ferro. Várias mudanças podem ser feitas nas pelotas para minimizá-lo. Conforme o sínter utilizado se torna cada vez mais básico, pelotas mais ácidas são desejadas. A adição de MgO, assim como a modificação da basicidade binárias das pelotas pela adição de CaO são soluções que têm sido apontadas. Dessa forma, este trabalho estudou os efeitos do MgO a da modificação da basicidade binária nas seguintes propriedades de pelotas: compressão a frio, porosidade e índice de inchamento. Foram preparadas pelotas com até 5% de MgO e com basicidades entre 0,67 e 1,5. O aumento do teor de MgO causou aumento de porosidade e queda de resistência. A basicidade diminuiu a porosidade e causou aumento de resistência nas pelotas de basicidade 1,0. Tanto o aumento de basicidade quanto a adição de MgO diminuíram o inchamento.

Oct 30, 2017

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Huang Qiming

The CISDI-GreenEAF innovatively applies the top-side-chute for charging for improving the cold zone of electric-arc furnace (EAF) requiring preheating scrap. It can greatly reduce the operating power consumption during EAF melting by combined use of fume for preheating scrap. The enclosed charging mode and specially-designed structure contribute to less emission of dust and fume during charging while enhancing the metal yield. Thanks to the extraordinary fume temperature control at scrap preheating procedure and fume quenching technology as developed by CISDI, for restraining the regeneration of dioxin.

Oct 30, 2017

By Xihuai Gong, Hongshuang Di, Jianping Li, Ning Yan

In this work, we investigated the effect of the rolling process (warm-rolled or cold-rolled) on microstructure evolution and mechanical properties of 9Mn steel. After intercritical annealing at 670°C for 10min, both cold-rolled and warm-rolled microstructures are composed of ultra-fined austenite and intercritical ferrite. The austenite in warm-rolled sample includes two types of morphology, namely equiaxed and lamellar, which exhibits a wide distribution of grain-size. The incomplete recrystallization or recovery behavior of ferrite in warm-rolled and annealed sample results in higher yield strength and shorter yield point elongation. Moreover, the warm-rolled and annealed sample extends the TRIP-related work hardening over a broad strain range, resulting in a better combination of ultimate tensile strength and total elongation.

Oct 1, 2019