Search Documents

By Paula Maria Gomes Cunha Leão, Flávio de Castro Dutra, Fabrício Vilela Parreira, Silvio Maranha

In the iron ore beneficiation, tailings are inherent in the concentration processes to which the ores are subjected for the production of commercial products. The large generation of tailings has been motivating the study of technological alternatives for its reuse, with the development of processes that contemplate the concentration of fine ore particles present in the tailings, such as the reintroduction of these particles in the process of manufacture of the iron and steel itself, through the agglomeration techniques such as briquetting. The aim of this article is to study the technical feasibility of the production of iron ore tailings and coking coal briquettes for use in reduction reactors, through a systematic review of the literature on agglomeration, briquetting and self-reduction processes, covering the main variables that influence the production of high quality briquettes, such as binders use, binder behavior of coking coal, coal granulometry, iron ore and coal proportion, compacting pressure and temperature of thermal treatment and the effects of these variables on briquettes final properties.

Oct 1, 2019

By Mozart Henrique Teixeira

As reservas de minério de ferro da Mineração Usiminas S.A. (MUSA) estão localizadas no extremo oeste do QF e ocupam a porção ocidental da Serra do Curral (Alkmin, 2009 [1]), também chamada Serra Azul e inseridas no Supergrupo Minas / Formação Cauê. Abrangem as Minas Oeste, Central e Leste. Atualmente a classificação geológica industrial adotada pela empresa leva em consideração o teor de ferro, contaminantes e compacidade (granulometria) das rochas. Os minérios são separados em dois domínios litológicos, hidratado e silicoso. Estes domínios apresentam comportamento granulo-químico fortemente heterogêneo tanto lateral como em profundidade (Teixeira, 2015 [2]), este comportamento confere ao planejamento da lavra elevado grau de dificuldade em relação às estimativas de massas e teores no que se refere à separação dos estéreis e minérios. Até novembro de 2015 o Planejamento de Lavra de Curto Prazo utilizava modelos de blocos atualizados mensalmente para a liberação de planos de lavra mensais e estimativas de teores do ROM, porém, ao longo do mês os desvios de teor na alimentação da planta e dificuldades na execução da geometria planejada eram frequentes. Diante disto, com foco na redução destes desvios, passou-se a gerar os modelos de blocos semanalmente para confecção de programações de lavra semanais e diárias com expectativa de liberação de estimativas de massas e teores com maior grau de confiança e melhor previsibilidade das características granuloquímicas dos produtos finais. Para a elaboração dos modelos semanais foram adotados novos métodos nas ferramentas de topografia, amostragem de frentes de lavra e mudança na rotina do mapeamento geológico, que passaram a ser executados semanalmente. Os resultados obtidos foram as reduções de desvios de teores na alimentação dos processos unitários das plantas e na produção de granulados.

Oct 30, 2017

By Tiago Rafael Ferreira de Brito

O presente trabalho comparou o desempenho do fosfato de zinco e do microfosfato de zinco, ambos com tecnologia dry-in-place para verificação do comportamento destes revestimentos frente à conformação mecânica, por meio do ensaio de embutimento Erichsen, método Nakazima e curvas limite de conformação (CLC). Foram estudadas chapas de aço-carbono grau EM e grau EEP G4 eletrozincadas e fosfatizadas. As chapas foram fosfatizadas empregando-se dois banhos: fosfato de zinco e microfosfato de zinco, ambos com tecnologia dry-in-place. A caracterização da morfologia dos fosfatos estudados por microscopia eletrônica de varredura mostrou que as camadas de fosfato de zinco não apresentaram formação de cristais, quando aplicadas por roll coater e as análises por EDS comprovaram a presença do elemento fósforo. O ensaio de embutimento Erichsen somado aos resultados obtidos nas curvas CLC demonstraram que o microfosfato exibiu desempenho melhor em comparação ao fosfato. A diferença entre os dois tipos de fosfato foi mensurável e evidenciou que a tecnologia dry-in-place colaborou com a produção de camadas fosfatizadas adequadas para a lubrificação durante o processo de conformação mecânica.

Aug 16, 2017

By Thiago Pinto Silva, Leandro Rocha Lemos, Luiz Fernando Andrade de Castro

This paper shows an evaluation about effect of dispersant sodium silicate along to limestone, in the form of pulp, on the cold agglomeration process for iron ore sintering. Before that, it was verified the effect of pH, solids content and amount of dispersant on the stability of the system (limestone, water and sodium silicate). It was found that the lower the solids content, the more alkaline pH and the amount of sodium silicate equal to 20 l for each 1t of limestone, was the level of dispersion of the system. The influence of the limestone pulp with dispersant depended on the granulometry of the ore mixture and the type of technological route. For the thinner type (42,8% <0.15mm), the limestone pulp with dispersant reduced the resistance of the adherent layer of the cold agglomerates, regardless of the technological route. However, for the coarser type (24,7% <0.15mm), the limestone pulp with dispersant increased the average size of the aggregates, preserving the resistance of the adherent layer when manufacturing with two intensive mixers in series.

Oct 1, 2019

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Samuel F. Rodrigues, Clodualdo Aranas Jr., Fulvio Siciliano

The application of thermo-mechanical control processing (TMCP) in hot rolling of steels has become a common routine since the last 60 years. The understanding of the physical metallurgy behind TMCP played a major role in the early developments. Physical and numerical simulation works are performed firstly to derive the fundamental metallurgical knowledge and secondly to conceive existing TMCP practices. In this paper, a summary TMCP techniques is presented. The occurrence of dynamic transformation of ferrite in the austenite region is shown by means of synchrotron light diffraction methods. This phase transformation mechanism is taken into consideration and its effects on TMCP are proposed in an exploratory way.

Oct 1, 2019

By Luís Marcelo Marques Tavares, Gilvandro Bueno, Túlio MoreiraCampos

The HPGR development and application in the minerals industry resulted in an important increase in its application in iron ore pellet feed processing in the last decades. Vale SA was one of the pioneers in application of the HPGR in integrated plants, currently operating with six HPGRs in the pelletizing plants of Complexo de Tubarão (Vitória, ES). The work uses the mathematical model of the HPGR, proposed by Torres & Casali and modified by the present authors, to predict the performance of two industrial pellet feed HPGR units of the Complexo de Tubarão. Besides model validation, results of process simulations are shown in order to optimize the pellet feed pressing according to industrial demands, presenting different scenarios that are more attractive to HPGR operation. Simulations showed that it is feasible to reduce the specific surface area of the HPGR feed from 1770 cm²/g to 1570 cm²/g, allowing to produce a pellet feed of the same quality in its product (1911 cm²/g) and therefore reduce the work done by upstream ball milling.

Oct 1, 2019

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Giulio Rodrigues Altoé

The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. PALF extracted from pineapple leaves, presents some significant characteristic, but until now only few studies on PALF were performed. This work aims to make the analysis of the tensile strength of polyester composites reinforced with PALF. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. After fracture the specimens were analyzed by a SEM (scanning electron microscope).

Aug 16, 2017

By Raquel Húngaro Costa, Jonathan Tenório Vinhal

The demand for natural resources has grown over the years, however, the environment offers a limited amount of these resources for exploration. Then, the investigation of new methods for recovering and reuse some compounds and elements are essential to know later tailings purposes. Zinc is used in corrosion resistance as a protective coating for several products. One of the steps for the extraction of zinc is by flotation process to obtain the concentrated ore, in which a residue is generated. The aim is to characterize this residue, allowing the choice of recovery routes for compounds and elements in future stages. The methods of analysis were Malvern, VA, Eltra and ICP-OES, besides the water content. In this study, a characterization of elemental chemical analysis was performed, in which the main elements presented were: calcium (17.4%), magnesium (10.3%) and iron (7.97%); the water content was 27% and the grain size of the material presented an average size of 50μm. With the presented characteristics the material can be used, after treatment, in the recovery of other compounds for applications in the sector of fertilizers, ceramics and steel industry.

Oct 3, 2019

By Rudolf Lesch

Till date, coke has been produced mainly from coals with a content of volatile matters in the range of 20% to 28% and good coking properties. If such so-called &quot;selfcoking&quot; coals are available, blast furnace coke or foundry coke with the required quality characteristics can be produced in top-charged horizontal ovens. In this case, the possibility of using high-volatile coals and in particular coals with low-caking properties is very restricted. Even if high-volatile coking coals have good coking properties, coke produced from such coal alone will not meet the requirements in terms of coke strength. The mechanical coke properties are influenced by the charge coal blend and the coking conditions. In this context, the bulk density of the oven charge is a decisive factor. Research and development in the field of coke production in horizontal chamber ovens aims at improving the specific oven throughput, increasing the raw material basis and introducing environmental protection technologies. The key factor, however, is to guarantee and further improve the rentability of the coke production. It is very important to reduce the cost of the charge coal to a minimum at the same time maintaining or even improving the coke quality.

Aug 17, 2017

By Jéssica Vicente Luiz, Rayander Martins Pimenta, Everton Pedroza dos Santos

The Hybrid Pelletized Sinter (HPS) is a agglomeration process that involves the combination of conventional sintering and pelletizing techniques and can be used with the purpose of obtaining improvements in the agglomeration stage of iron ore, and one of the great advantages of the process is the use of a wide particle size range of the ore. In this way, the superfines of low-cost ores, which are improper in sintering, can be used in the HPS process for the formation of the quasi-particle. The use of HPS with the sintering plants of the industries presented throughout the study, enabled an increase in productivity, decreased fuel utilization and reduced slag formation in blast furnaces. Thus, the present study aims to present a review of the literature on the Hybrid Pelletized Sinter (HPS) process and its main characteristics, as well as the results obtained by the companies that adopted the process.

Oct 1, 2019

By Bruno Pinheiro Silva, João José dos Santos Carvalho, Flávio Túlio Busatto, Leonardo Passos Perdigão

Sinter has high participation in the blast furnaces ferrous burden in ArcelorMittal Tubarão, being therefore of paramount importance the constant control of its physical, chemical and metallurgical qualities, aiming at the fulfillment of the client required quality. With the great challenges faced by market conditions, steelmaking companies seek operational sustainability, aiming at stability and reducing costs. One of the main steps to obtain these results in the Blast Furnaces is the raw materials quality stabilization, in order to guarantee the perfect burden distribution control and a better use of the reductant gas inside the reactor, aiming a lower fuels consumption. It is known that the smaller a ferrous particle is, better its reducibility, since a larger surface area provides greater contact with the reductant agent. Based on this concept, the objective of this work is to quantify the effect of the sinter size produced in ArcelorMittal Tubarão Sinter Plant in its reducibility, and in this way enable the definition of a better sinter particle size distribution aiming at a balance between the permeability effects and gaseous yield in the Blast Furnaces. In addition, the reducibility effects on sinter size reduction were evaluated, where the 5 to 10 mm fraction was analyzed in two sinter samples, the first obtained from the conventional route and the second after crushing of the fraction over 50 mm, in order to simulate the effect of the use of a Secondary Crusher in Sintering.

Oct 1, 2019

By Lindaura de Souza Cândido d’Ávila, Robert Nogueira de Azevedo, Itavahn Alves da Silva, Mariana Carvalho Araújo

The present study aims at the reduction of the dolomitic limestone by the addition of lime added with high MgO (magnesium oxide) content in the sintering process. To verify the feasibility of the use of additive lime as an alternative source of magnesium oxide, sintering tests were carried out at pot grate with different percentages of additive lime addition and with proportional reduction of the calcite lime dosage, evaluating the effects on the sintering process. The results showed that the additive lime is a good source of MgO for consumption in the sintering process of iron ore.

Oct 1, 2019

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Priscilla Pessin Coppo

The prevention of dental enamel wear has particular relevance for preventive and restorative purposes in dentistry. The wear damage can increase due to salivary disorders and/or parafunction (bruxism); antagonists incisal surfaces become flat and coincident. This study aims to investigate the wear behavior and the related mechanisms in sliding pairs of conformal incisal enamel, with similar values of hardness and fracture toughness, with different applied normal loads and lubricated conditions. Bovine incisors, under pin on flat configuration, were tested in two lubrication condition (dry or with natural saliva) and two applied normal loads (8 and 16 N). The worn surfaces were investigated by 3D profilometry and SEM. The analysis of worn surfaces indicated mechanisms of brittle fracture, but with different severities. Under a normal load of 16 N and dry condition, wear is controlled by a brittle process: microcracking with flake-like wear particles, which results in high friction coefficient (> 0.85), wear rate and wear volume. On the other hand, under a normal load of 8 N and natural saliva, wear took place in the interprismatic region, with consequent exposure of prisms and fracture in localized regions. In this case, the friction coefficient was 16% lower and the wear volume was one order of magnitude lower. Under 8 N and natural saliva, the wear was greater than in the dry condition, probably due to tribochemical reactions.

Jul 31, 2018

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By Silvio Pereira Diniz Maranha, Evandro Costa e Silva

The disposal of coal tailings in an economically and environmentally sustainable way can be considered one of the biggest challenges for coal producers due to their physical, chemical and mineralogical characteristics and the significant annual volumes generated. The processing and utilization of coal fines is recognized as one of the great technical challenges of this industry. These challenges become even greater when it comes to the use of tailings from coking coals. This is due to the potential changes in their various properties, variability of these characteristics along the deposits, the handling and dewatering aspects of the products and the granulometric restrictions imposed by the coking plants for the coals to be handling and coking. This work presents the current stage of project development for the use of a metallurgical coal fines dam, addressing the general concept of the project, the exploratory sampling program and the characterization of the tailings for process and product development purposes after processing. It aims at the characterization and the carbonization tests for product development, the mining method considered, product alternatives, suitable to the market, to be generated and the next steps.

Oct 3, 2019

By Ismael Vemdrame Flores, Lindaura de Souza Cândido D’ Avila, Maurício Covcevich Bagatini, Arthur Felipe Lino Oliveira, Rafael Adriano Lopes Júnior

The use of pellet feed to adjust the chemical quality of the sinter is an alternative to the depletion of iron ore reserves. However, the addition of ultrafine in the sintering process can cause decrease of permeability and consequent drop in machine productivity. In this context, the present work investigated the addition of natural and ground pellet feed, evaluating its effects on cold agglomeration for sintering and quality of quasi-particles produced. Eight typical mixtures with industrial composition were produced in the laboratory, replacing Sinter Feed with different percentages of Natural Pellet Feed (NPF, 91% <150 μm) and Ground Pellet Feed (GPF, 83% <44 μm). The mixtures were subjected to cold agglomeration tests and the quasi-particles produced were evaluated by screening, shatter test, permeability test and disintegration into primary particles analysis. There was a decrease in the mean particle size of quasi-particles and reduce in permeability with addition of the ultrafines. The addition of NPF favored the layering mechanism in larger quasi-particles. The coalescence mechanism occurred for larger additions of NPF and GPF, being more expressive for GPF additions.

Oct 1, 2019