Search Documents

By Maria Carolina Andrade Teles

Uma fibra natural apresenta características interfaciais com matrizes poliméricas que favorecem a absorção de alta energia de impacto da estrutura compósita . Este trabalho procura avaliar a resistência ao impacto deste tipo de matriz de poliéster com reforço de fibras naturais. As fibras de Fique foram misturadas com resina de poliéster sob pressão em um molde metálico, e curada à temperatura ambiente durante 24 horas . Amostras padrões foram preparadas até 30% em volume de fibras Fique alinhadas ao longo de todo o seu comprimento, estas amostras foram então testadas com ensaio de impacto Izod do pêndulo e as superfícies de fratura examinadas por microscopia eletrônica de varredura, MEV. A resistência ao impacto aumenta substancialmente com a quantidade relativa de fibra de Fique como reforço do compósito . Isto pode ser atribuído a uma descolagem preferencial da interface fibra / matriz , o que contribui para uma elevada energia absorvida.

Aug 17, 2017

By Alexandre de Souza Rios

Neste estudo, caracterizações morfológicas e mecânicas foram utilizadas em fibras de coco brasileiras na condição como recebida e tratadas superficialmente (por NaOH, aquecidas e por NaOH seguido de aquecimento) e em mantas de fibras de coco fabricadas por compressão. Para a análise morfológica foi utilizada a Microscopia Eletrônica de Varredura (MEV) e para a análise mecânica foi utilizado o ensaio de tração uniaxial. As análises por MEV apresentaram que as fibras tratadas por NaOH possuem paredes celulares externas mais nítidas e partículas circulares com diâmetros de aproximadamente 10 µm. O tratamento químico alterou a parede externa das fibras de coco; em uma das amostras foram vistas microtrincas da ordem de 7 a 60 µm em virtude do tratamento seguido de aquecimento. O módulo inicial (módulo de elasticidade) e a tensão de ruptura diminuíram com o aumento de diâmetro nas quatro condições de fibras de coco estudadas. A geometria e a massa da manta de fibra de coco influenciaram no seu comportamento mecânico.

Aug 16, 2017

By Eustáquio Vieira Júniorr, Dalton Martins Neto, Filipe da Costa Oiveira

O Alto-Forno 2 da Ternium Brasil, no Rio de Janeiro, iniciou sua primeira campanha em 16 de dezembro de 2010. No decorrer de sua campanha, verificaram-se problemas de deslocamento de staves de ferro fundido e deformação dos staves de cobre chamado “efeito banana”, causando a perda da capacidade de refrigeração destes componentes do sistema de arrefecimento. Após a análise dos eventos foram executadas diversas ações para recuperação e preservação do Alto-Forno 2, sendo estendidas também ao Alto-Forno 1. Dentre as ações de preservação para o Alto-Forno 2 foi estabelecido que deveriam ser substituídos os staves danificados e alguns setores da carcaça que apresentavam trincas e deformações, e consequentemente a perda de suas propriedades mecânicas, visando eliminar as interrupções na operação do Alto-Forno 2 para reparos localizados e redução das instabilidades operacionais causadas pela não uniformidade das superfícies dos staves. O trabalho apresenta o detalhamento da técnica utilizada para substituição dos staves, a seleção dos materiais assim como os preparativos operacionais que garantiram o bom desempenho do Alto-Forno 2 nos momentos que antecederam a parada e após seu retorno à operação, mostrando a viabilidade técnica e econômica da atividade.

Oct 1, 2019

By Cameron Soltys, Hamid Ghorbani, Maher Al-Dojayli

Cooling staves in blast furnaces are used to minimize the process heat loads on steel shell and refractory system. Copper staves are exposed to significant fluctuating thermal loads which may lead to premature stave failures due to cracks, water leakage, bending, abrasion and resultant wear. In this paper, an assessment methodology is presented to evaluate the effect of thermal cycling on copper staves including bending, fatigue and thermal ratcheting. This approach incorporates temperature-dependent copper properties including creep and plasticity to more accurately capture inelastic deformations, damage and fatigue in staves under transient and cyclic thermal loading conditions. Root cause failure assessment and improvements to copper stave design can be assessed using the presented methodology.

Oct 1, 2019

By Severino Albani Junior

A Gestão de Ativos vem ganhando espaço no contexto industrial ano após ano principalmente após 2014, quando ocorreu o lançamento da ABNT NBR ISO 55000. Dentro desse contexto, o tema Manutenção e principalmente a Confiabilidade foram explorados pela ArcelorMittal Flat Carbon South America com o lançamento em 2013 do Plano Diretor de Manutenção e Gestão de Ativos. Este trabalho visa mostrar as etapas seguidas na aplicação de técnicas de Engenharia de Confiabilidade, os atores necessários para a realização do trabalho e os resultados positivos alcançados. Dentre os resultados está a definição da estratégia da manutenção focando a manutenção baseada em condição, possibilitando a otimização dos recursos envolvidos e influenciando positivamente na redução da taxa de falhas da Máquina de Lingotamento Contínuo 01 da ArcelorMittal Tubarão. Estes resultados também levam a expressivos ganhos financeiros, além de melhora da previsibilidade operacional.

Oct 30, 2017

By Günther Staudinger

Danieli Linz Technology has been honored at 4.1.2013 with the first contract for the exchange of a 350 t BOF converter for ArcelorMittal Poland Dabrowa Gornicza on a turnkey basis. This paper describes the new design features of this converter based on the development of a new Danieli converter suspension system. The issue was to install a new converter (incl. trunnion ring, suspension system and bearings) with maximum volume but keeping most of the existing equipment unchanged. So, the big tilting drives on both sides had to be reused and the existing foundation, pedestals as well as the bearing distance had to be maintained. Further on the welded coreequipment (vessel shell, trunnion ring, pedestals, slag shields, etc.) was manufactured in-house within the pressure vessel division of Danieli Thailand. Due to the huge dimensions of these parts the delivery had to take place in parts which had to be welded together on site under full production conditions of the steel plant. But also the erection had to be applied under this condition. Additionally the main support bearings, parts of the screening (doghouse) as well as an upgrade of the existing relining machine had to be delivered.

Jul 29, 2018

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Anand Kumar Agrawal, Kinzel Klaus Peter, Lorenzo Micheletti, Cristiano Castagnola, Horst Kappes, Andre Oliveira, Björn Rösner, Philippe Bermes

Blast furnaces are widely employed today for iron production all around the world, with a total production of around 1.2 billion tons per year. Its operating principle, which relies on usage of coke to reduce the ore, to ensure the permeability in the reaction vessel, to maintain its flexibility of operation and acceptability for varying qualities of iron ores. The blast furnace route is widely considered as the most economic and efficient route of iron production, however it is based on fossil energy carriers. The blast furnace route has undergone significant developments in terms of energy efficiency in the last decades, which led to a substantial reduction in the use of fossil reduction materials. Being an energy intensive process, competitiveness and cost saving in the blast furnace plant was always strongly related to the saving of energy and hence reduction of CO2 emissions. In addition to this, EU emissions trading system (EU ETS) as a cornerstone of the EU's policy in response to climate change has set new “challenges” for iron production in Europe. Paul Wurth has always been deeply involved in the development of energy saving technologies for blast furnaces. In the following a review of energy saving achievements developed in the last decades will be presented and the potential of available CO2 saving technologies will be summarized. Additionally, an outlook about the potential of future technologies, concepts and their impact on the blast furnace and the steel plant’s energy balance will be discussed. Finally, the replacement of carbon by hydrogen as reduction agent in the steel plant will be reviewed, with special focus on a comparison of costs and incentives.

Oct 1, 2019

By Huang Qiming

The CISDI-GreenEAF innovatively applies the top-side-chute for charging for improving the cold zone of electric-arc furnace (EAF) requiring preheating scrap. It can greatly reduce the operating power consumption during EAF melting by combined use of fume for preheating scrap. The enclosed charging mode and specially-designed structure contribute to less emission of dust and fume during charging while enhancing the metal yield. Thanks to the extraordinary fume temperature control at scrap preheating procedure and fume quenching technology as developed by CISDI, for restraining the regeneration of dioxin.

Oct 30, 2017

By Benito Barbabela e Silva

O pelotamento é a mais complexa etapa de aglomeração de finos de minério de ferro. Sua resposta é naturalmente oscilante, sendo bastante influenciada pelas características físicas obtidas nos processos de beneficiamento mineral que a precedem e tem papel crucial para a etapa de tratamento térmico de sinterização à jusante. O presente trabalho aborda o processo de classificação de pelotas verdes, sólidos singulares de aspecto deformável e pegajoso, em peneiras de rolos por modelamento por aplicação de Método dos Elementos Discretos. Esta técnica mostra-se como uma importante ferramenta pois supera as limitações impostas na modelagem física (quantificação e identificação de fluxos por ausência de instrumentação em escala industrial, amostragem sem representatividade) ao reproduzir de forma verossímil as repostas do sistema para importantes variáveis de controle: comprimento de gap, umidade, dispersão de tamanhos e resistência das pelotas.

Oct 30, 2017

By Douglas Glenn Stalheim

Production of structural hot strip coils in yield strengths up to 700 MPa and higher is increasing worldwide. In addition to requiring higher strengths, structural designs require good formability, toughness and weldability. Toughness and formability come from optimization of ductility properties while weldability comes from lower carbon equivalent alloy designs. The key to the production of optimized cost effective hot strip produced structural coils is to create the correct balance of a proper alloy/processing design to create as fine and uniformly distributed cross sectional grain size as possible. In addition to the creation of the fine/uniformly distributed cross sectional grain size, the correct microstructure needs to be created. In the higher yield strength grades, not only does the grain size/distribution play a role but a proper understanding and control of microalloying precipitation kinetics is required. This paper will present various examples of hot strip alloy designs to produce cost effective hot strip structural coil in yield strengths up to 700 MPa with good ductility and weldability. In addition, steelmaking/casting parameters will be discussed to assure successful production. Optimized reheating, rolling and cooling parameters of these alloy designs will be introduced in an accompanying paper.

Aug 17, 2017

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017

By Florian Markus Penz

The increase in Basic Oxygen Furnace (BOF) plants in steelmaking has given rise to renewed interest in a dynamic simulation of the BOF process. Material and process costs can be saved with optimized process times and targeted charging of scrap and slag formers. Beside hot metal, scrap is the main source of iron in the BOF process. Furthermore, scrap is used as a coolant during the process due to exothermal chemical reactions occurring in the BOF. In this paper, the melting and dissolution behaviour of scrap in the BOF process is discussed. A new dynamic thermodynamic and kinetic Matlab® model used to simulate scrap melting behaviour as a function of various scrap surface parameters and particle size is presented, as well as the influence of scrap properties on liquid bath temperature and final crude steel composition after a defined blowing period.

Oct 30, 2017

By Jose Maria Rodriguez-Ibabe, Ronaldo Antonio Neves Marques Barbosa, Douglas Glenn Stalheim

Major costs in the production of both flat and long commodity grade structural steel products include alloy, labor and energy. Flat and long commodity grade structural steels such as ASTM A36, ASTM A527Gr50, S235, S275, S355 and other equivalent world societal standards represent over 500 million annual tons worldwide. These simple commodity grades consist of a minimum of three base common alloying elements, carbon, manganese, silicon and then can be supplemented with microalloying elements of either vanadium or niobium. Since 2016 raw material costs for two of the five alloying elements in these commodity grade structural steels, FeMn and FeV, have risen significantly and/or have become volatile making it difficult to maintain stability in profitability for these commodity grades. For steel plants producing hundreds of thousands and in some cases over a million tons annually of these common structural steel grades because of the significant alloy cost increase for Mn and V alloy additions has squeezed profitability of these grades. These grades typically represent the base loading for cost controls in most all steel plants and hence a significant cost increase or volatility in two of the five elements used for these grades having a negative effect on overall production costs. However, with a proper strategy for alloy designs working in conjunction with the mills existing processing capabilities to achieve the desired end metallurgy/mechanical properties, alloy costs and operational efficiencies can be realized.

Oct 1, 2019

By Pedro Forastieri de Almeida Prado

A fim de recuperar-se todos os materiais presentes em painéis fotovoltaicos, o emprego de solventes orgânicos para promover a dissolução da fração polimérica e liberação dos componentes é uma alternativa ao tratamento térmico tradicional. Com o objetivo de verificar-se o impacto dessa etapa na recuperação de prata, o metal de maior valor presente nos painéis de silício cristalino, comparou-se taxas de recuperação de prata para rotas distintas de separação de materiais e cominuição: uma rota por dissolução do encapsulante através de solventes e uma rota por tratamento térmico e destruição do encapsulante. Utilizando-se o isopropanol como solvente, ainda foi analisada a contribuição da cominuição para a liberação da prata. Os ensaios de lixiviação foram realizados com soluções de 5M HNO3, analisando-se as concentrações de prata por ICP-MS. O processo de calcinação foi realizado em forno a 480°C, a dissolução do encapsulante realizada com isopropanol e a cominuição realizada em moinho de facas. Foi concluído que a separação com isopropanol não afetou a quantidade de prata lixiviada na etapa de recuperação de metais. Além disso identificou-se que a cominuição não seria necessária sob as condições de lixiviação utilizadas, já que poderia potencialmente contribuir para perda de prata no processo.

Oct 30, 2017

By Alexander Fleischanderl

Steel market has become somehow unpredictable and requires quick adjustment in production conditions to survive in the harsh market environment. Steel production is not anymore driven by output records, but by efficient cost reduction measures to remain competitive under strongly varying production conditions. Energy efficient production and flexible raw material scenarios have become decisive factors to succeed and survive in our industry. Such scenarios have to be carefully investigated to be well prepared to adopt production steps continuously. The paper analyses various process opportunities to optimize energy and raw material consumption in the production route. Off-gas treatment systems have still a huge untapped potential to recover energy from the hot waste gases. This is valid for the EAF mini mills as well as for the integrated route. Various examples for waste heat recovery systems including resulting benefits are discussed for the EAF, agglomeration, blast furnace, direct reduction and BOF. New innovative bag-filter systems feature extremely low emission levels at lowest pressure loss and sound emission conditions. Also improved control and automation solutions support the operators to minimize the operation and maintenance costs of their off-gas system. Steelmaking by-products shall not be considered as residues, but as a valuable and cheap raw material source. The paper presents some show cases how to valorize slags as well as utilizing coke and iron oxide fines to increase productivity and minimize raw material cost. A new process for highly flexible converter steelmaking allowing for extraordinary high HBI and scrap rates above 50% and improved yield is discussed and evaluated

Oct 30, 2017

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Leonardo Lúcio de Araújo Gouveia

Este trabalho objetiva o estudo da influência da adição de fibras vegetais de bambu e cana-de-açúcar nas propriedades mecânicas do concreto. Para este trabalho foram confeccionados corpos-de-prova cilíndricos e prismáticos nos quais foram adicionados 2% e 5% em volume das fibras à massa do concreto. Após a cura, conforme NBR 5738 (2003) [1], os mesmos foram testados via ensaios de resistência à compressão conforme NBR 5739 (2007) [2], resistência à tração por compressão diametral, conforme NBR 7222 (2011) [3], resistência à tração na flexão conforme NBR 12142 (2010) [4] e módulo de elasticidade estático, conforme NBR 8522(2008) [5]. Verificou-se após os testes que todos os concretos produzidos atenderam a resistência mínima a compressão de 20 MPa, recomendado pela NBR 6118 (2003) [6] para fins estruturais. Foi observado um aumento da resistência à compressão em relação à mistura padrão. O concreto com adição de fibras de bambu apresentou melhor resistência mecânica em relação ao concreto com adição das fibras de cana-de-açúcar e ao concreto sem adição.

Aug 7, 2018