Search Documents

By José Adilson de Castro

In the integrated steel industries the sintering process plays an important role furnishing raw material to the blast furnace. In this work, a computational simulation of the sinter process is developed that is able to predict the most important phenomena within the sintering bed. The model is based on the multi phase concept with multiple components described by conservation equations of each component coupled with the momentum, chemical reactions and heat transfer. The model validation was carried out comparing the model predictions with averaged industrial data and local temperature measurements within the sinter strand. The model predictions presented good agreement with the averaged values measured on the industrial sinter process.

Aug 2, 2018

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By Klaus Pronold

Once installed rolling mills can look forward to a long life. Around 40% of the 140 conventional hot strip mills presently in operation were built between 1960 and 1970. 17 of the 29 CSP®-plants were commissioned before the year 2000 and have automation platforms that are obsolete and/or have outdated rolling technology. Keeping pace with the market requirements is an ongoing challenge for producers of flat steel. It is a real balancing act keeping production facilities performing at necessary levels, safeguarding the investment and keeping outage periods to a minimum. To overcome these demanding factors and strike the right balance allowing for the production of higher grade steel that meets the current market price the installation of mechanical equipment as well as automation platforms and process technology must meet the latest technology standards. Being discussed in this paper are the different motives for modernizations along with their impact on project handling and commissioning philosophies. Experience gained during recent modernization projects in the field of flat steel rolling relating to Steckel / plate mills or current CSP® modernizations will be shared and demonstrate that each modernization has its own individual solution. Specific strategies are explained to help optimize production, increase plant agility and maximize the return on investment.

Aug 17, 2017

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019

By Ananda Moreira Vaz Ourique de Avila

Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells (SOFC) interconnects, replacing the ceramic materials. However, at high temperatures, on the order of 700-850 0C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the SOFC. Thus, the knowledge on kinetics of oxidation/corrosion of these steels and their relationship with the microstructural transformations are of great importance. In this study, samples of ferritic stainless steels AISI 430, AISI 441 and Crofer22APU® were tested for oxidation at high temperature (800 0C) for long periods of time (up to 3,600 hours) and mass gains were monitored allowing the determination of the oxidation behaviors of these steels. Additionally, the microstructural characteristics of the samples before aging (corrosion-oxidation test) and after various oxidation times were evaluated by optical (OM) and scanning electron microscopy (SEM), as well as by micro chemical elemental analysis (EDS) and X-ray diffraction (XRD) phase analysis. Electrical characterization allowed determination of electrical area-specific resistances (ASR) characteristics of the systems studied, thus relating the electrical and oxidative behaviors of steels evaluated.

Aug 7, 2018

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019

By Fabiano Almir Barbosa, Eduardo Alves Machado, Felipe Ferreira Cajano, Bruno Rodrigues Henriques

Spring steels are usually classified as medium to high carbon low alloy steels with very high yield strength, enabling the part to return to its original shape regardless of significant bending or twisting. Despite the fact that plain carbon steels are suitable for small springs, larger and high performance springs usually requires alloy steels such as Cr-V or Si-Mn in order to achieve an even microstructure throughout the cross section. Clutch diaphragm spring is a high performance part that requires very good cleanliness and microstructure homogeneity, thus requiring an alloy steel. In this paper was studied, in an industrial scale, the process parameters and critical characteristics for the development of a Cr and V alloyed high carbon sheet steel for the production of clutch diaphragm spring. The steel was characterized throughout the entire process (casting, hot rolling, cold rolling + batch annealing and heat treated) using tensile test, hardness test, optical microscopy (OM) and scanning electron microscopy (SEM) to assess the mechanical and metallurgical properties of the studied steel. The results have shown the material’s microstructure evolution after each main stage of the process, from a ferrite-bainite/perlite based microstructure as hot band to fully spheroidized as cold-rolled/annealed and then fully martensitic as ready-to-use part.

Oct 1, 2019

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Vitor Guarnier Domiciano

Pre-shaped refractory burner blocks play an important role in reheating furnaces operation and melt shops production since they are responsible for heating the billets/plates so that they reach the temperature required for lamination. This paper presents the main characteristics and properties of a new refractory castable developed for pre-shaped burner blocks, which significantly improved the performance of reheating furnaces burner blocks. Tests carried out in 3 different melt shops have shown that the new refractory castable was able to extend the service life of the refractory burner blocks from 1 year (standard product) to more than 3 years (new castable), showing perfect conditions to continue operating for a longer period.

Oct 30, 2017

By Filippo Verlezza

Conventional wire rod blocks have some limitations. They can only roll with fixed reduction ratios which always require the same rolling diameters within the block. With MEERdrive® SMS, as a pioneer, has introduced an innovative drive concept for wire rod blocks that can overcome the limitations of conventional solutions. The clue: the concept is based on individual drives for each stand position. The exigent wire rod market demand and the available technology melt in a new variant of MEERdrive®, the MEERdrive®PLUS, which represents a sizing block solution for finished size rolling and allows conventional as well as thermomechanical rolling. Further “one family rolling” is also possible, since all roll / size changes will occur in this block.

Oct 30, 2017

By Giulio Rodrigues Altoé

The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. PALF extracted from pineapple leaves, presents some significant characteristic, but until now only few studies on PALF were performed. This work aims to make the analysis of the tensile strength of polyester composites reinforced with PALF. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. After fracture the specimens were analyzed by a SEM (scanning electron microscope).

Aug 16, 2017

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Luigi Giacomini, Bruce Kiefer

A new plant for special steel long products was commissioned in recent years at Dangjin, South Korea, for Hyundai Steel. Two multi-line rolling mills can produce yearly 1 million tons of billets, straight and coiled bars, with dimensions from 5.5 to 350 millimeters. The products are used for manufacturing engine and transmission components used by Hyundai Kia Automotive Group. The processed grades include carbon, special alloy, spring, bearing and free-cutting steel. The first mill rolls blooms into finished large round and square products, as well as into intermediate billets. A 2-high reversing breakdown stand is followed by a finishing and sizing train with CGA stands equipped with an under-load roll parting system for automatic gap control. The second mill combines lines of small bars, rods and bars-in-coil. Billets are rolled in a continuous rolling mill with original RedRing Series 5 stands. The rod outlet features Morgan No-Twist and Rod Reducing/Sizing mills, Morgan High-Speed Laying Head and Stelmor conveyor. Advanced sensors and electronics integrate with mechatronic packages, thus equipping the mill for Industry 4.0 applications. Hyundai can meet the demanding requirements posed by the automotive industry and benefit from optimized conversion costs, the flexibility to meet market changes, achieve high product quality, and reduce floor personnel.

Oct 1, 2019

By Alberto Lainati

The Bar Reducing and Sizing Technology has a core function in the value-chain for the production of rolled SBQ (Special Bar Quality) products. The EVO 2+4-roll is based on the compact combination of a 2-roll high-reduction module followed by a 4- roll low-reduction module for precise sizing. The EVO 2+4-roll mill, allows to gain significant technical and economical advantages in the hot- and post-rolling process routes: dimensional and surface accuracy, quick adaptability to processing variances and to small lots requirements, superior technological features of as-rolled product, competitive capex and opex. The EVO 2+4 unit has a very compact design, which makes it suitable both for new mills and upgrade applications.

Aug 17, 2017

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By Rodrigo Martins, Mauro Trindade

I Reduction of energy consumption in air compressors by the implementation of individualized load control. Reduction of 3,5% from Jun / 18.

Oct 3, 2019

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Patrick Edward Connell

The next generation of the well-established 3-roll Reducing & Sizing Block (RSB), the RSB SCS® is the latest milestone in reducing and sizing technology for SBQ products. It offers enhanced bar quality, improved productivity, mill availability and economy as well as a simplified, safe and environmentally friendly operation. A newly developed modular drive concept of the RSB SCS® grants a smaller footprint in the layout, a reduced oil-lubrication volume and a simplified maintenance schedule. Intelligent engineering leads furthermore to reduced hydraulic functions of the RSB SCS®, which ensures a safe and environmentally friendly rolling. Another integral part of the RSB SCS® is an innovative stand changing concept, which allows automatic stand changing within three minutes. The new RSB SCS® also includes a Fast Remote Control (FRC) which enables the immediate adjustment of the roll gap against the rolling force (under load) within milliseconds. Size changes along the free-size range can also be made within the traditional billet gaps in less than five seconds. At the core of the future-oriented RSB SCS® is a real-time closed-loop control system called Size Control System (SCS®) acting with 3-roll stands adjustable under load (AUL) and / or the heavy duty stands. These features remarkably further improve the rolled tolerances and their reproducibility, and at the same time simplify the operation by means of an automated optimization of the process parameters for the rolled bars.

Aug 16, 2017

By Stefano Scubla

DANIELI Q-MELT is the latest evolution of EAF concept to automatically control each stage of the melting process, from the electric power planning to the combustion optimization as well as the slag and steel metallurgy management for every operation required in the EAF cycle. The core of the automation system is the Melt-Model that automatically identifies deviations of the process control variables and corrects them to avoid losses or wasting of available energy sources. The real-time online off-gas analysis, via the in-situ laser system, promotes the process tracking and permits further optimization by a viable closed-loop control acting on fuel and oxygen postcombustion. A suite of supplementary stand-alone Technological Packages integrates the Q-MELT to further maximize the productive time and the utilization factor, supporting the operators to limit downtimes, avoiding misoperations and/or mistakes.

Aug 16, 2017

By Ernst Lindemann

The SMS group has developed the ultrasound technology “HD scan” for inspection of the internal quality of as-cast products. This method of sample analysis requires less preparation work and is safer than the current, most common technique of etching and/or sulphur printing. Furthermore, this technology offers a three-dimensional view into the sample of the cast product and thus more representative information for a better quality evaluation. The internal quality evaluation can be performed automatically and objectively by software based on clear statistical methods. A quantitative centerline segregation rating can be assigned to each sample, based on the size and distribution of segregates detected by the unit. Internal crack statistic (length, position, orientation, etc.) and narrow side profile can also be measured. Grain macrostructure can also be visualized which allows for a potential optimization of casting parameters like strand cooling, soft reduction or electromagnetic stirring. The accuracy of the new method was proven by parallel metallographic investigations of more than 100 samples of different steel grades and sample shapes. Automatic defect evaluation and classification was compared against macroetching results. It was found that HD scan identified more defects and the visualization of the macro structure could be performed in more cases than with macro etching. All tests, comparisons, further developments and analyses for various steel producers and steel treatment companies have been conducted at the HD scan unit, located at the SMS group headquarters in Düsseldorf, Germany (Figure 1). Based on the results, SMS group has designed a unit which can be used in industrial scale.

Aug 17, 2017