Search Documents

By Frank Schrama

Steelmakers worldwide agree that the most efficient and cost-effective solution in BOF steelmaking is to desulfurize the hot metal between the blast furnace and converter. Various methods are currently in use, among which the Kanbara Reactor (KR, using only lime as a reagent), Magnesium mono-injection (MMI, using only magnesium; also known as the Ukraina-Desmag process) and co-injection (using magnesium and lime/CaC2) are leading. These three hot metal desulfurization methods are compared based on metallurgy, efficiency, costs and overall performance. Both available data from literature and experience from Danieli Corus engineers is used for this study. The KR process is able to reach low sulfur concentrations (> 10 ppm) in hot metal and has lower reagent costs. However, due to higher Fe-loss and heavy wear the KR process has the highest operational costs. The Magnesium mono-injection process is very fast due to the use of the reactive magnesium as reagent. Major problems with resulfurization (sulfur levels below 50 ppm cannot be reached) and the violence of the process made that this process could never get a firm foothold in the western steel industry. The co-injection process with magnesium and lime proves to be able to combine the best of both worlds. It can reach low sulfur concentrations and desulfurize fast. Co-injection is also the most flexible and cost effective.

Aug 16, 2017

By Michael Brandner

HSM can be divided into different groups such as Conventional HSM with Roughing stands and HSM without Roughing stands = Mills with just finishing stands. The roll requirements for different stands are quite different. In Roughing stands the temperature of the slab is very high. Therefore the resistance against thermal wear/fatigue is the most dominating factor. Today mostly Chrome Steel, Semi HSS and HSS rolls are applied. A comparison and evaluation of such rolls will be described. In the finishing mill the tendency/wish is to use HSS rolls in all the stands. The grade HSS is defined by at least a certain amount of carbide forming elements such as V, W, Mo, Nb etc. The matrix and other precipitations can be adjusted according to the need and situation in the mill. In the pre-finishing stands the HSS is already well introduced. In the last finishing stands the original HSS tended to stick and the cobble rate increased. New development decreased the problem and gave some very promising results. In the last finishing stands beside the high performance a higher resistance against incidents is needed. Solutions in this direction including e.g. residual stresses and special core material will be discussed. Proper testing and grinding procedures can avoid losses and reduce the TCO. Data sourcing and evaluation in regards of rolling and grinding is the key for the optimization of the TCO. Several examples and comparison between different applications will be given in detail and explained. Future possibilities will be discussed as well as results of latest trials in mills.

Aug 17, 2017

By Felipe Fardin Grillo

The aim of this work was to study the use of slags to desulfurization of cast iron. It was proposed to use alumina instead fluorspar. In addition, marble waste was used instead lime. Simulations applying Thermo-Calc software were performed in order to obtain the theoretical phases thermodynamic data. Then, a comparison between theoretical data and experimental tests were performed. The cast iron was melting in induction furnace at 1550°C. Slags composed mainly for CaO and Al2O3 were used to cast iron desulphurization. It was observed that increasing liquid phase, the desulphurization reaction was favored. Besides, it was found that cast iron desulfurization occurs by top slag mechanism.

Aug 17, 2017

By Massimilinao Svetina

In 2010 Danieli & C. S.p.A. put into operation a new Pickling Tandem Mill in Cremona (Italy) at Acciaieria Arvedi, the last Pickling line coupled Tandem Cold Mill (PLTCM) in Europe. The plant was tailor-made to suit the specific requirements of this customer; a very broad range of sizes and grades (IF to AHSS as well as DP and TRIP1000) including ultra-thin hot band can be processed, achieving a total capacity of 1.6 Mt/y. The Danieli & C. S.p.A. Turboflo® process was selected because of its proven efficiency and ability to handle ultra-thin gauges at speeds exceeding 400 mpm in the pickling tanks. All the equipment, i.e. pickling section and rolling mills was provided with the last generation of Danieli market-oriented technologies. Danieli & C. S.p.A. - with the support of Arvedi and feedback from the field - is continuously improving its technical design solutions and optimizing plant operations.

Aug 16, 2017

By Nicola Santangelo

The current economic crisis and growing environmental issues have led the steel industry to face the simultaneous effects of low demand and production overcapacity in a globalized steel market, whilst confronting high energy prices and the need to comply with the green economy. Heat Recovery from waste gas of the Electric Arc Furnace (EAF) represents one of the greatest opportunities to reduce the consumption of primary energy and reduce the CO2 emissions in steel industry. The heat of the off-gas, if recovered and converted into electrical power, can make the whole Fumes Treatment Plant autonomous from the electric point of view, thus making it a “Zero-Energy FTP”. The concept is to substitute the Cooling Components (Water Cooled Panels and Air Cooler) are substituted with Heat Recovery Components (Hot Water Cooled Panels and Heat Exchanger). The recovered heat can be converted into power by using an Organic Rankine Cycle (ORC) turbine. The heat recovered by the HWCP and the Heat Exchanger is characterized by a variable thermal power, which affects the efficiency of the downstream ORC System. Danieli, in collaboration with the University of Udine, has developed the Thermal Stabilizer Unit (TSU). Danieli has realized the first step towards Zero Energy FTP at ABS steelmaking plant (Italy) by installing a CHR® - Clean Heat Recovery. This plant has been started up on 17th October 2014. The HMI of the CHR® is integrated in the HMI of the furnace, so all the process could be kept under control by the furnace operator. At ABS recovered thermal power reaches 5.5 MW. The max power production reached with CHR plant in ABS (over 1MW of electric power) consents an annual saving of approx. 500,000 EUR.

Aug 16, 2017

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018

By Zhisong Chai, Wei Xu

Q&P steels undergo continuous multiple processes, including hot rolling, intermediate heat treatment, cold rolling and continuous annealing etc. The inheritant effect of initial microstructure could affect the final microstructure and mechanical properties of Q&P steels. In this work, effects of different hot rolled microstructure/texture on the final microstructure and properties subjected to Q&P process were investigated in Fe-0.38C-1.58Mn-1.6Si system. Different initial microstructures were generated combing different TMCP and cooling strategies. The microstructure and texture of hot rolled materials were characterized in detail. The hot rolled material was subsequently processed by intermediate annealing, cold rolling and continuous annealing. The comparison reveals great effects of the initial hot rolled microstructures, i.e. inheritance effect. The faster reverse transformation would lead to more sufficient austenitization and it would greatly weaken the inheritant effect of the initial microstructure. Although the difference of final phase fraction for different initial microstructures was not significant, the inheritance effect was mainly reflected in the effect on austenite morphology. For the mechanical properties, no obvious difference in strength was shown for the samples with different initial microstructures after Q&P heat treatment, but there was fluctuation in elongation.

Oct 1, 2019

By Paulo Conceição, Carlos Sampaio, Carlos Petter, Ariane Kuerten

The Sensor Based-Sorting technology is an emerging technology applied in mineral separation and concentration. The technique consists in using a method known as Dual Energy X-ray Transmission sorting (DE-XRT). The particle's position over the conveyor belt was evaluated and, despite de variability of results, shows that there is no a position with greater accuracy on the sensor's reading. Results obtained indicated that DE-XRT sorting technology was able to significantly reduce the mass and the ash content of the ore feed, being an interesting option for reduction of costs and improvement of coal quality in beneficiation plants.

Oct 3, 2019

By Henrique Silva Furtado

This paper presents the results obtained on the exchange of an original old blow charge model for a new up-to-date state of art global model, employing optimization techniques and process modelling, and, the results obtained in terms of fluxes consumption reduction and the introduction of user friendly tools and practices.

Aug 17, 2017

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By Edo Engel

Whereas only a handful of decades ago, typical blast furnace working volumes were below 1000 m³, such furnaces are currently designated compact or even mini blast furnaces. For certain business cases, however, small furnace sizes remain an attractive option. Decades ago, this size blast furnace would have produced a maximum of 0.3 Mtpa with its 600 m³ working volume over a campaign of up to four years. The current state of technology and operational know–how will allow a similarly sized furnace to produce over 0.7 Mtpa while achieving the multiple decade campaigns that have become familiar to steel producers in full sized operations. This level of productivity, but especially the reliability and supply security associated with mature technology, allows for integration into minimills or taking a first step towards a full scale BF–BOF integrated mill. Steel producers considering such scenarios, which are typically attractive for emerging economies, are confronted with fundamental decisions, one of which is for the technological basis for the compact or mini blast furnace to be included in the plant. This article addresses some of these decisions from an operations–based perspective. A small number of case studies is included.

Aug 16, 2017

By Hiroshi Ichikawa

In 2013, Nippon Steel & Sumikin Engineering Co., Ltd. (hereafter referred to as NSENGI), Tenova HYL and Danieli have entered into an agreement to combine ENERGION DR technology into blast furnace technology and/or with syngas technologies. This new alliance will allow the three companies to combine research and development activities with their respective expertise in ENERGIRON DR technology, Blast Furnace technology and Syngas (by-pro gas and coal gasification) technology, with the ultimate objective to develop breakthrough iron making technologies and create such EPC projects. This paper introduces the concepts and the features of our breakthrough technologies of combining of ENERGIRON DR technology, Blast Furnace technology and Syngas technology.

Aug 16, 2017

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Daniel Augusto Godinho de Carvalho

At thyssenkruppCSA, a positive heat balance at BOF process is faced, mainly because of low utilization of scrap and plant design. A singular logistic concept for hot metal transport between blast furnace and steel plant was established to optimize transportation and energy balance. Up to 80 kg of iron ore pellets/t steel is necessary for 340t BOF heat balance. In order to accomplish this challenge a stable blowing process, intensive operational development have been successfully executed: slopping rate reduction of 80% achieved without changing the blowing time. This paper describes steps and results of this development.

Oct 30, 2017

By Andreas Munko

A Outotec está desenvolvendo em escala piloto o queimador de baixa emissão de NOx desde 2012, resultados expressivos foram atingidos (o pedido de Patente já foi depositado). Em 2014 utilizando simulações CFD, os resultados atingidos em escala piloto foram reproduzidos com boa aderência e os resultados em escala industrial se mostram com os mesmos comportamentos em tendências dos resultados da escala piloto, se mostrando promissores também. O presente trabalho apresenta os passos de desenvolvimento, os promissores resultados e o próximo passo deste desenvolvimento é realizar um teste em escala industrial com o queimador desenvolvido.

Aug 17, 2017

By Ivan R. Jankov

No setor industrial no mundo todo, são exigidas as emissões cada vez mais restritivas. Nas plantas onde o Precipitador Eletrostático já está instalado, a solução com o melhor custo-benefício para reduzir as emissões de material particulado abaixo de 20 mg/Nm3 é com o Filtro Híbrido. Esta tecnologia consiste em combinação dos princípios de operação de um Precipitador Eletrostático (utilizado na entrada do sistema), com uso de campo elétrico para separação de material particulado do fluxo gasoso, e de um Filtro de Mangas (utilizado na saída do sistema), com uso de tecido para retenção de material particulado. Salienta-se que a viabilidade de implementação do Filtro Híbrido depende da configuração original do Precipitador Eletrostático (i.e. altura das placas, número de campos, largura da carcaça) que determina o espaço disponível para mangas, bem como as velocidades máximas do gás dentro da carcaça. Na indústria siderúrgica, este tipo de retrofit já é utilizado em planta de sinterização, mas também é aplicável para despoeiramento de fornos de cal e de plantas de pelotização.

Oct 30, 2017

By Maria Olivia de Barros Almeida

O intuito do presente trabalho é identificar, dentre as proporções entre resina e catalisador analisadas cineticamente, a melhor condição de cura. O mecanismo de cura das resinas epóxi é um dos mais estudados e a técnica mais utilizada no estudo deste comportamento é a calorimetria exploratória diferencial (DSC). Neste trabalho, foi utilizado o equipamento DSC 1, fabricada pela Mettler Toledo, pelo método dinâmico. Por meio da técnica de DSC, pode-se observar perfis de cura, temperatura de transição vítrea e a determinação das melhores condições de preparação de compósitos. A reação de cura de resinas termofixas é um processo complexo, definido como uma mudança irreversível nas propriedades químicas e físicas por uma reação química. Estabelecendo-se as condições ideais de cura, a resina epoxi resulta em uma estrutura rígida altamente reticulada, a qual combina as excelentes propriedades térmicas, mecânicas, resistência química.

Aug 17, 2017

In today’s competitive steelmaking environment, the optimization and continuous supervision of the blast furnace process is of major importance. Modern probes and process measurement systems can assess the specific operation of the blast furnace. They provide a better and detailed process understanding and control. The benefits are even more important when they are combined with process models and expert systems. Everyday operation, productivity and even the lifetime of a blast furnace can be significantly improved by collecting, interpreting and acting upon such process data correctly. Only a comprehensive knowledge of the various process phenomena together with measurement of process variables inside the blast furnace enables the operators to optimize coke and fuel rates, to run the blast furnace smooth, reliable, and safe, and to make best use of the available raw materials. While the improvement of the blast furnace process with respect to productivity remains the main task, also, the timely identification of abnormalities and the assessment of process variations is an objective. This paper describes the blast furnace measurement systems that are available for everyday automatic use and provides an understanding for the possibilities of modern probes. The different applications are daily blast furnace supervision, charging process optimization, and observation of the internal state. Finally, the paper gives recommendations on probe configurations for different blast furnaces sizes, considering both a technical and an economical point of view.

Aug 2, 2018

By Luiz Antônio da Silva

Este trabalho tem como objetivo apresentar os resultados do procedimento de geração de energia elétrica adicional a geração econômica na CTE2 com gás natural, visando a redução de custo no grupo CSN.O estudo foi efetuado através da avaliação dos preços do mercado de curto prazo de energia elétrica e análise do processo de geração da planta, aos quais permitiram diagnosticar as melhores praticas e definir a melhor configuração operacional.Os resultados apresentados foram significativos para as condições de operação, o que representa redução do custo de energia elétrica para o grupo CSN e aumento da segurança operacional da planta da CTE2.

Jul 31, 2018