Search Documents

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By Michel Fillon

Hydrostatic assistance is a commonly used method to improve limited load carrying ability of tilting-pad thrust bearings during transient states of operation of the vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves etc.), it also requires manufacturing of special recesses/pockets at the pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up of the machine and form a hydrostatic film between the pads and the collar. There is a quite wide variety of geometry of recesses (shape, depth, size) met in practical large bearing applications. The presence of a hydrostatic pocket (usually located in the sliding surface above the pivot area, where thin film, high oil pressure and temperature are observed) affects bearing performance under hydrodynamic operation. In theoretical researches, there is an almost common practice not to include hydrostatic recess in THD or TEHD analysis. This is probably due to the problems with obtaining solution for oil film geometry with pocket, with pocket depths order of magnitude larger than gap thickness. In this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of ltaipu power plant. Bearing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket.

Jul 31, 2018

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019

By Miguel Araújo Vasconcelos Filho, Ulisses Tetti

In order to determine the influence of the number of increments of the sinter sample on the variability of the chemical composition obtained in Sinter Plant production, a variographic study was carried out. It was performed with two series of samples. The first series was composed of 40 samples with a 6-second interval, with the objective of obtaining the so-called minimum practical error, resulting from the extraction processes of the sample of the conveyor belt and preparation and analysis in the laboratory and the second series composed of 60 samples with a range of 4 minutes, which points to the sample selection error. The results obtained showed that the minimization of the sample selection error occurs for increments spaced in 15 minutes, being in agreement with ISO 3082, but with significantly better results than those currently practiced for intervals between 1hour increments. It was then decided on the suitability of the sampler to allow hourly increments to be collected and on a second opportunity to install a sampling tower with primary and secondary samplers to collect increments every 15 minutes including sample size reduction.

Oct 1, 2019

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By Johann-Paul Stemplinger

For lubrication of open gear drives applied in rotary furnaces, often gear greases are used as well as for lubrication of gear boxes in difficult sealing conditions. The selection of the gear grease influences strongly the wear behavior. Investigations with flow greases NLGI 00 were made in a back-to-back test rig determining the weight loss due to wear acc. to the standardised procedure ISO 14635 part 3. Different influences like base oil viscosity, thickener type and additional solid lubricant type were analysed. Only the type and amount of solid lubricant shows a significant influence on the weight loss due to wear. Finally, a linear wear coefficient clT according to the calculation method of the wear amount according to Plewe is derived and can be used to transfer the test results to any gears in practice.

Jul 31, 2018

By Jürgen Schanderl

Cold rolling mills by SMS Siemag are well known for their reliability and long-life cycle. They are an investment in the future. Nowadays mill owners are under considerable competitive pressure and are asked to organize production in a more and more efficient and flexible way. Doing so, a number of elevating screws have to be turned. These are: cutting of operation costs, especially by more efficient equipment and processes as well as transition to more process flexibility to fulfil future product requirements. To support owners in their effort, SMS Siemag offers convincing solutions in cold rolling technology under the brand X-Roll 2.0. Examples to be presented are: Sieflex®-HT drive technology; Redesigned DS system; New reel design: Twin Reel; Emulsion compact unit ECU Compact; TRC® threading assistance system; ECOMode and Energy ADVISOR monitoring system.

Jul 30, 2018

By Jorge Madias

Pin holes as a surface defect, and blow holes as an inner defect, occur in billet / bloom / beam blank casting, particularly for Si-Mn killed steel cast with metering nozzle and oil lubrication. If they are present in abundance or have a large size, they may originate defects in the rolled products. Their characteristics, factors behind their formation, as well as usual processing conditions that promote their occurrence are discussed. Finally, the evolution of these defects during reheating and rolling is analyzed, with industrial examples.

Aug 16, 2017

By Breno Totti Maia

This work was a continuous and multidisciplinary development. Through studies of the blowing process and its parameters results, evolutions, improvements and adjustments were made on the lance’s hot face with Slagless® technology, as well in the process parameters and mitigating actions of the projection of materials out of the converter. The main results are the increase in the nozzle’s life with a “record mark” of 1785 heats, and water leakage occurrence in the cartridge decreased considerably reaching the mark of one year without any occurrence.

Oct 30, 2017

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Adrian Villanueva

In this study, we compare the influence of two water soluble polymer-based organic binders added to bentonite, to form a hybrid-binder system for Iron Ore Pelletization. The kinetics of the agglomeration process and resulting properties of green pellets were analyzed, and examined in detail through Scanning Electron Microscopy (SEM) and Confocal Laser Scanning Microscopy (CLSM) analytical techniques. It was encountered that the differences in the mechanical properties of the pellets produced by each binder system could potentially be explained by the ability of the polymer to interact with bentonite at a macromolecular level.

Oct 30, 2017

By Felipe Darabas Rzatki

Polyether ether ketone (PEEK) is a high performance thermoplastic often selected for high temperature tribological applications under chemically aggressive environments. The present work evaluate the tribological behavior of a high performance PEEK composite under ambient and high temperature (30 and 80°C, respectively). The atmosphere was also varied (air or tetrafluorethane). An AMTI tribometer equipped with a hermetic chamber and a heating system was used to carry out sliding tests of PEEK cylinders on 304 stainless steel polished discs (Sq < 10 nm) with reciprocating movement and 175 N normal force. Surfaces roughness analyses were performed with a white light interferometer. As expected, there was a strong influence of temperature on the tribological behavior of the samples tested in ambient atmosphere (25% decrease in friction coefficient associated with a 100% increase in wear rate). On the other hand, samples tested in tetrafluorethane atmosphere showed no significant friction temperature dependence.

Jul 31, 2018

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By José Adilson de Castro

In this paper a new technology for a compact iron ore sintering machine is analyzed. The compact sintering process is based on the massive injection of gaseous fuels and the solid fuel is only agglomerated fine charcoal obtained by biomass. The solid fuel used in this study is obtained by agglomeration of fine charcoal produced from elephant glass which has very short period for production and CO2 capture(less than 6 months in tropical climate). To overcome the lower heat supply into the combustion front of the sintering process the simultaneous injection of oxygen and gaseous fuel is proposed. The proposed methodology is to combine the solid fuel (agglomerated fines charcoal) and steelworks gases in a compact machine to enhance heat and mass transfer with high productivity (about 5 times the conventional large machine). A multiphase mathematical model based on transport equations of momentum, energy and chemical species coupled with chemical reaction rates and phase transformations is used to analyze the inner process parameters. A base case representing a possible actual industrial operation of the sintering machine is used in order to compare different scenarios of practicable operations which represents advanced operations techniques. The model was used to predict six cases of combined operation with biomass and fuel gas utilization with oxygen support.

Aug 2, 2018

By Steven G. Jansto

Nearly one third of the globally produced structural flat and long structural products are in the 0.11 to 0.16% carbon range. By definition, numerous steelmakers globally define this approximate carbon range as peritectic in their melting grade family within their organization. The metallurgical consequence is the result of numerous global structural specifications which allow carbon to wide carbon ranges resulting in quality issues. For example, such specifications as ASTM A588 set no minimum carbon and a 0.15 to 0.19%C maximum depending on the specific grade designated within the specification. This peritectic region is specifically challenging in production compared to less than 0.10%C because of solidification issues and a higher propensity for slab or billet cracking during continuous casting. During hot rolling, rejects and/or deviates are increased as well. The relative steelmaking operational cost of production is compared between peritectic and non-peritectic carbon compositions for a given specification.

Aug 17, 2017

By Afshin Sadri

One of the main reasons for blast furnace reline is the loss of refractory lining, particularly in the hearth and taphole regions. Intense operation of the blast furnace can result in extensive refractory wear and deterioration. This can then affect the continuity of the operation and the furnace campaign life. Novo-Lipetsk (NLMK) and Hatch developed a systematic approach to monitor the condition of blast furnace hearth linings using Acousto Ultrasonic-Echo (AU-E), a non-destructive testing system developed by Hatch. Continuous and periodic inspections of blast furnaces revealed areas with accelerated refractory deterioration, formation of elephant foot, extent and speed of refractory wear, as well as cracks and other anomalies. Improvement in coke quality, stave washing, the addition of titania, and other changes were recommended and implemented to prolong furnace life while maintaining the intensity of furnace operation. This paper demonstrates how the coordinated efforts between NLMK and Hatch resulted in prolonging the blast furnace campaign life.

Aug 17, 2017