Search Documents

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Vitor Guarnier Domiciano

Pre-shaped refractory burner blocks play an important role in reheating furnaces operation and melt shops production since they are responsible for heating the billets/plates so that they reach the temperature required for lamination. This paper presents the main characteristics and properties of a new refractory castable developed for pre-shaped burner blocks, which significantly improved the performance of reheating furnaces burner blocks. Tests carried out in 3 different melt shops have shown that the new refractory castable was able to extend the service life of the refractory burner blocks from 1 year (standard product) to more than 3 years (new castable), showing perfect conditions to continue operating for a longer period.

Oct 30, 2017

By Filippo Verlezza

Conventional wire rod blocks have some limitations. They can only roll with fixed reduction ratios which always require the same rolling diameters within the block. With MEERdrive® SMS, as a pioneer, has introduced an innovative drive concept for wire rod blocks that can overcome the limitations of conventional solutions. The clue: the concept is based on individual drives for each stand position. The exigent wire rod market demand and the available technology melt in a new variant of MEERdrive®, the MEERdrive®PLUS, which represents a sizing block solution for finished size rolling and allows conventional as well as thermomechanical rolling. Further “one family rolling” is also possible, since all roll / size changes will occur in this block.

Oct 30, 2017

By Giulio Rodrigues Altoé

The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. PALF extracted from pineapple leaves, presents some significant characteristic, but until now only few studies on PALF were performed. This work aims to make the analysis of the tensile strength of polyester composites reinforced with PALF. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. After fracture the specimens were analyzed by a SEM (scanning electron microscope).

Aug 16, 2017

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By Rodrigo Martins, Mauro Trindade

I Reduction of energy consumption in air compressors by the implementation of individualized load control. Reduction of 3,5% from Jun / 18.

Oct 3, 2019

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Stefano Scubla

DANIELI Q-MELT is the latest evolution of EAF concept to automatically control each stage of the melting process, from the electric power planning to the combustion optimization as well as the slag and steel metallurgy management for every operation required in the EAF cycle. The core of the automation system is the Melt-Model that automatically identifies deviations of the process control variables and corrects them to avoid losses or wasting of available energy sources. The real-time online off-gas analysis, via the in-situ laser system, promotes the process tracking and permits further optimization by a viable closed-loop control acting on fuel and oxygen postcombustion. A suite of supplementary stand-alone Technological Packages integrates the Q-MELT to further maximize the productive time and the utilization factor, supporting the operators to limit downtimes, avoiding misoperations and/or mistakes.

Aug 16, 2017

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By Edo Engel

Hot Blast Stove Technology has been developed to such an extent that low cost hot metal production for over 30 years without major repairs has become achievable, making the decision for a campaign length between 5 to over 30 years a design choice for the plant owner/operator. Some of the earlier examples of designs capable of such long campaign lengths are currently close to the 50th year of their running campaign. These examples are found especially in Europe and North America. Along the duration of these campaigns, repairs to subsystems such as burners, hot blast outlets etc. may be required. Depending on a plant’s up and down stream production capacities, the repairs may have to take place in the shortest possible time frame to minimize production loss. This article discusses an approach for intermediate repairs, executed while keeping the majority of the system at operating temperature.

Oct 30, 2017

By Francesco Toschi

The Special Bar Quality family comprises a wide range of steel grades, mainly requested by the automotive, energy and engineering sectors, for applications where significant performances are required (eg. stresses, temperatures, working cycles, etc.). To meet these requirements it is necessary to reach a precise control of both the mechanical characteristics and metallurgy structures along the whole production chain. For semi-product with large dimensions, such as equivalent diameters around 300 mm, this is traditionally obtained through a manufacturing route which comprises the casting in ingots followed by reheating, forging and rolling. After 2010, new processes were investigated and technologies developed to replace the ingot route with a continuous casting followed by controlled high-reduction rolling. In these processes a seamless integration of CCM with rolling is implemented so to obtain the precise control of material flow, applied deformation and working temperatures. By using the proper combination of rolling diameter, speed and applied reduction, a very good control of the metallurgy structure across the whole section can be obtained, so to also remove the internal discontinuities ("voids") generated during the continuous casting. These processes, which can be defined "forging-like", are applicable to several grades also with large semi-product dimensions (300 mm and more). Besides, removing the ingot route means increased yield and productivity, which is very beneficial to the economical management of the plant. An example of this "forging-like" process is represented by the high-reduction blooming stand installed by Acciaierie Venete in the Padova-Camin mill. This article describes its main concepts as well as its technology and process features.

Oct 30, 2017

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By Karl K. Bagger, Felipe Bertelli

The competitive scenario of steel industry requires studies and developments to improve manufacturing processes focusing on increasing productivity and reducing costs. The practice of coating rolls for cold rolling with the chrome aims to increase the rolling campaign, reducing their wear by increasing the surface hardness, which guarantees a greater homogeneity in the surface of the rolled products. The present paper presents a study on the effect of the chromium coat on a forged steel rolls on the wettability of a SkinPass solution. The hardness of the coated layer and the contact angle were measured for two concentrations of solution on two types of surfaces, comparing the coated and uncoated surfaces. The results show that there is an influence of the coating on the wettability of the fluid when comparison are made with chrome coated and uncoated materials, being verified through tests in Goniometer. The productivity of the coated rolls showed higher productivity than the uncoated ones.

Oct 1, 2019

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By Francisco Morganti

The market requirements which strip processing lines have to deal with have altered significantly within the last decades. Particularly, the production has to be economical and ecological efficient and processing lines have to cover a broad product portfolio. Already existing plants either directly or indirectly are competing with new plants, which are equipped with the latest technologies. The “Special Strip Processing Equipment” is designed to be integrated easily and within small downtime phases in existing lines. All single machines can be delivered in short time “ready-to-perform” with a tested and proved automation system. Thus, the competitiveness of existing lines can be increased immediately with less effort. To find out which machines can be reasonably implemented SMS group offers an “Efficiency Check”. A special proceeding is used by experts to find out quickly which machines will have the largest effect on the efficiency of the line while demanding at the same time the smallest expense.

Aug 17, 2017

By Jan Lampke

Increasingly pelletizing discs are used for the recycling of dust and sludge. The applied pellet feed is highly variable, for example in terms of chemical composition, grain size distribution and raw density. These raw materials related factors lead to a destabilized pelletizing process, which initially must be homogenized through special mixtures, as well as the use of binders or additives. There are many possibilities to reach stringent restriction of material related target factors. On the one hand it is helpful to be flexible by changing the process parameters of the pelletizing disc. On the other hand, it is necessary to use a material-binder-formulation, which leads to a highly stable pelletizing process. The paper deals with an example of the use of agglomerating device, pelletizing disc, to prepare different dusts and sludges for material recycling. These dusts und sludges are mostly generated in metallurgical processes, e.g. sinterplant, blast furnace and steelworks.

Aug 16, 2017

By Jean-Philippe Houde

The Blast Furnace Campaign lifetime is highly depending on the wear progress of the hearth lining. This progress is monitored in general through single and double thermocouples at the cold side of the lining. This type of monitoring becomes ineffective as soon as heat resistance will be formed in the refractory lining. Paul Wurth’s monitoring system, consisting of MTP-Sensor and Heat Flux Probes, is able to identify such heat resistances to give a true hearth lining wear. Since last year Paul Wurth is also able to install safely those MTP-Sensor and Heat Flux Probes on running blast furnace without salamander tapping, thanks to a newly developed cooled core drilling device. Blast Furnaces that are equipped with Paul Wurth’s monitoring system have optimized their campaign lifetime as they received right information upon the true wear lining such as detection of heat flux transfer failure, detection and monitoring of brittle layer or detection of hot spot.

Aug 16, 2017

By Giulio Antunes de Medeiros, Leonardo Martins Silva, Giselle de Mattos Araújo, Rayla de Souza Caldas

To analyze the direct reduction of self-reducting briquettes producted with different electric arc furnace dust contents, three sets of homogeneous mixtures were produced with elephant grass biomass, iron ore, cement and furnace dust in increasing levels, which were submitted to thermogravimetric tests in muffle furnace and TGA furnace at variable temperatures and times. The curves of degree of reduction were obtained and the reduced briquettes were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that the reducibility of the agglomerates is diminished by the increase of furnace dust, with variations of this result at higher temperatures. The observed microstructures were spherical particles, porous structure or whiskers. Based on XRD results, it was considered probable that the decrease of the degree of reduction with the increase of furnace dust content is related to the reaction between hematite and zincite, which is expected to be controlled by zinc diffusion.

Oct 1, 2019