Search Documents

By Rubson Mação Camporez

Estudos recentes indicam que o gasto devido à corrosão nos USA giram em torno de 276 bilhões de dólares por ano, isto significa 3,1% do PIB deste país, tendo a corrosão atmosférica uma importante parcela deste montante. Muitos estudos foram realizados a fim de determinar a agressividade da atmosfera e avaliar os efeitos da corrosão atmosférica nos metais usados para aplicações estruturais. Este artigo tem como objetivo comparar dois ambientes em termos de severidade da atmosfera, assim como sua influência na degradação do aço estrutural ASTM A-572 Grau 50. Toma-se como cenário a planta industrial da Medabil Sistemas Construtivos, localizada em Serra, região metropolitana de Vitória/ES. O estudo foi realizado por meio de monitoramento de perda de massa de amostras expostas deste material e comparação dos resultados com os obtidos através do teste padrão proposto pela American Society for Testing and Materials (ASTM G116, 1999), Wire-on-Bolt Test for Atmospheric Galvanic.

Aug 16, 2017

By Denisio Miranda Custódio, Rodrigo Boyer, Josiane Lira Batista Haagensen, Raquel Teixeira Pereira, Felipe Viana Pimenta, Rossano Augusto Pilon Nunes

In the Tubarão Pelletizing Plants, anthracite is used as solid fuel, which has fixed carbon content of 72%. This paper will present the pilot scale results and industrial scale tests of an alternative fuel to anthracite, named Blast Furnace Dust. All the work was developed using samples from Arcelor Mittal Tubarão, due to it has a large source of production and is near to Vale/SA, which reduces significantly the cost for the material’s transportation. There was an impact on the variability in fixed carbon results of the slurry, mainly at the beginning of the test, reaching very high levels and put on risk the pellets physical’s quality. This variation can be explained by some operational disturbances and, mainly, by the low predictability of Blast Furnace Dust quality and lack of an adequate system for material preparation and dosage.

Oct 1, 2019

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By Daniel Massari de Souza Coelho

Ligas de ferro com diferentes teores de cromo, carbono e cobalto foram expostas a uma condição de atmosfera dupla, onde um lado da amostra é exposto ao vapor d'água e o outro lado a gases ricos em CO2, semelhantes aos encontrados em usinas termelétricas a carvão que utilizam o processo de oxicombustão. Os ensaios realizados em condição de atmosfera dupla a 600°C foram comparados com ensaios realizados em atmosfera simples onde todos os lados das amostras foram expostos ao mesmo gás. As amostras foram caracterizadas para comparar a corrosão em atmosferas simples e dupla e para analisar a influência dos elementos de liga na oxidação destes materiais utilizados em processos em altas temperaturas.

Aug 7, 2018

By Fernanda da Silva Machado

Em um mundo de recursos naturais decrescentes, com a intensificação das indústrias automatizadas de todos os tipos (I4) e contínuo aumento da população, é necessário desenvolver melhores caminhos para a geração e distribuição de riquezas. Uma das alternativas para este objetivo é o conceito da Economia Circular. Este artigo apresenta um exemplo focado na intensificação do uso de resíduos de biomassa na produção integrada de aço exclusivamente baseada na combinação de reatores industriais existentes em um layout que favorece o conceito da economia circular. O ferro também é obtido do processamento tradicional de sucata, reprocessamento de resíduos de ferro e óxidos de ferro, como a escória, pequenos óxidos de ferro, reversos metálicos, resíduos da indústria siderúrgica integrada tradicional. Os resíduos de biomassa são provenientes da demolição de casas de madeira, e outros resíduos de biomassa, como limpeza florestal para evitar-se incêndios, resíduos de moinhos, paletes usados e qualquer outra fonte de biomassa. As combinações dos reatores tornaram-se possíveis devido à nova versão do processo de Carbonização Contínua, Carboval, um reator especialmente projetado da tecnologia Lambiotte tradicional, para produzir, de preferência, o carvão vegetal que possui as mesmas características necessárias para alimentar o Mini Alto Forno tradicional a base de carvão.

Oct 30, 2017

By Jorge Madias

O trabalho está baseado na análise de dados de perto de 200 fornos elétricos a arco de diferente design: convencional, de corrente contínua, de carcaças gémeas, com preaquecimento de sucata no transportador ou em shaft, etc. Incluem-se fornos que processam principalmente sucata, e fornos com carregamento parcial de gusa sólido ou líquido, ferro briquetado a quente (HBI) ou ferro esponja (DRI) a frio ou a quente. São avaliados os consumos de energia elétrica, oxigênio, gás natural e materiais carbonosos; os tempos entre vazamentos, com forno ligado e com forno desligado, assim como a produtividade horária. Com os dados obtidos, se analisa a influência dos metálicos (e seu estado térmico ao momento do carregamento), e o design do forno, sobre os consumos específicos mencionados e a produtividade.

Oct 30, 2017

By Ana Paola Villalva Braga

O objetivo deste trabalho é apresentar as soluções implementadas para modernização e automação do laminador piloto do Instituto de Pesquisas Tecnológicas do Estado de São Paulo-IPT, importante ferramenta de pesquisa do seu Centro de Tecnologia em Metalurgia e Materiais. O IPT, em parceria com o Laboratório de Fenômenos de Superfície da EPUSP, tem trabalhado nas duas últimas décadas com o desenvolvimento de ligas resistentes a desgaste, principalmente para uso em cilindros de trabalho para laminação a quente. Com recursos provenientes de projeto co-financiado pelo BNDES e pela Gerdau, o laminador piloto e o forno de indução para aquecimento de placas foram reformados e modernizados, permitindo que a célula de laminação trabalhe de forma autônoma e que os dados de processo sejam continuamente registrados. Nesse projeto estão sendo conduzidos ensaios de laminação de longa duração para caracterizar e quantificar o dano progressivo imposto aos cilindros pela laminação a quente de placas de aço carbono sob condições controladas de temperatura e grau de deformação e de refrigeração dos cilindros. A modernização do laminador envolveu 3 etapas: reforma e automação do laminador e do forno de aquecimento; montagem do sistema de refrigeração dos cilindros e instrumentação dos cilindros de trabalho.

Jul 30, 2018

By Afshin Sadri

One of the main reasons for blast furnace reline is the loss of refractory lining, particularly in the hearth and taphole regions. Intense operation of the blast furnace can result in extensive refractory wear and deterioration. This can then affect the continuity of the operation and the furnace campaign life. Novo-Lipetsk (NLMK) and Hatch developed a systematic approach to monitor the condition of blast furnace hearth linings using Acousto Ultrasonic-Echo (AU-E), a non-destructive testing system developed by Hatch. Continuous and periodic inspections of blast furnaces revealed areas with accelerated refractory deterioration, formation of elephant foot, extent and speed of refractory wear, as well as cracks and other anomalies. Improvement in coke quality, stave washing, the addition of titania, and other changes were recommended and implemented to prolong furnace life while maintaining the intensity of furnace operation. This paper demonstrates how the coordinated efforts between NLMK and Hatch resulted in prolonging the blast furnace campaign life.

Aug 17, 2017

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Andrea Zanon

Recently steel manufacturers have significantly focused their attention on safety and working conditions thanks to new labour laws, comprehensive operators’ knowledge and increased company social responsibility. Even with a reduced budget, investments on safety are now widely approved. Mill constructors aim at developing upgraded solutions to comply with these new requirements. In some cases mill constructors can even anticipate customers’ requests and consequently put into the market innovative solutions. In this text we will analyze some advanced solutions developed by Danieli & C. Officine Meccaniche Spa - the leading company in long-product rolling mills - aimed at improving working conditions on wire-rod block settings. In particular, we will focus on rolling guides installed on fast-finishing blocks and on servo-assisted device for rolling rings changing. In fact, this equipment has shown effective benefits on our test plants and has mainly cut out the tendency of the personnel to be absent due to backache. This paper will first present standard working conditions, will then introduce the newest equipment developed by Danieli & C. Officine Meccaniche Spa, will analyze its operation and finally will describe in detail the benefits that can be reached with its use.

Jul 30, 2018

By Aline Lima da Silva

The present work is focused on the thermodynamic study of the methane or biogas mixtures conversion on Cu-ceria catalysts. Several experimental studies reported in literature have demonstrated the ability of these materials to operate as SOFC anodes for direct methane oxidation, with the evidence of enhanced tolerance towards sulfur poisoning and carbon deposition. More recently, experimental investigations have shown the feasibility of Cu-ceria anodes to directly operate with simulated biogas feeds at intermediate temperature (1023K). In this way, the effect of the ceria redox properties on the equilibrium composition is investigated, considering methane or biogas mixtures as the fuel. Conditions under which carbon deposition and sulfur poisoning can be prevented are determined. Our study combines results from the classical thermodynamics, obtained with the help of FactSage software, with the new Cu-S and Ni-S diagrams proposed in literature, which were calculated based on the Density Functional Theory (DFT). These diagrams are able to predict a region where sulfur interacts with the metal surface through chemisorption. A comparison between the performances of Ni-YSZ and Cu-CeO2 catalysts is established from a thermodynamic viewpoint. Theoretical results are in agreement with the experimental trends from literature.

Aug 8, 2018

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By Alessandro Molinari

In recent times, coke oven machines are acquiring a more prominent role in the coke making process. Apart from the traditional handling of the coal and coke flow, nowadays these machines are also deeply involved in all environmental and process control aspects. Paul Wurth coke oven machines have been developed by Schalke to meet the most recent requirements in terms of emissions control, automation, instrumentation, operability and maintainability. In CSP, Ceará, the new coke making plant represents the status of the art of the technologies applied to the whole coking process; starting from the Coke Oven Batteries and the Gas Treatment Plant developed by Paul Wurth up to the Coke Machines supplied by Schalker Eisenhütte, whose technology is now part of Paul Wurth coke making products portfolio. Present paper describes the plant configuration focusing on Coke Oven Machines and the key factors which are guarantying the success of the project.

Aug 16, 2017

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By Nicolás Lugo

The electric steel industry has reached a level of maturity in its relative participation in the world’s steel production. As the industry has grown and matured, EAF steel producers have participated in an ever more competitive market. This competition has led to a continuous search for lower cost alternatives for energy and input materials. Over the years, the Electric Steel Furnace community of operators has developed a variety of technological improvements geared to increasing EAF productivity. Operators have emphasized lowering operating costs and improving the quality of steels produced. Depending on market conditions, the EAF operators may run with different goals and priorities. In times of low demand, the goal may be to operate with an emphasis on cost and the goal of maximizing cost effective use of resources. When the market demand is high the goal may be to maximize EAF throughput. The objective of this work is to list some of the EAF operating best practices observed by our team in the electric arc furnace operations around the world. EAF operators can consider and possibly implement these practices depending on the specifics of each EAF operating reality.

Jul 29, 2018

By Márcia M. S. M. Pereira, Hervé Tavernier, Gérson T. Ferreira, Caio Nogueira Araujo Diniz, Fabio Luiz Lourenço, Wagner C. Moreira, Vinicius Cunha Aranda

Pós fluxantes desempenham um papel significativo na qualidade do aço durante o processo de lingotamento contínuo. Os pós fluxantes são escórias sintéticas usadas para lubrificar o molde durante o lingotamento contínuo do aço. Para que isso ocorra, o fluxante deve apresentar as seguintes funções: isolamento químico e térmico do aço, absorção de inclusões não metálicas do aço, lubrificação do molde e controle da transferência de calor entre o aço e o molde. O desempenho de cada função está relacionado às propriedades químicas e físicas do pó fluxante, que são dependentes de sua composição química e sua composição mineral, devido a sua relação com a taxa de fusão do material. A fim de garantir uma produção eficiente e de alta qualidade durante o lingotamento de um aço ultra baixo carbono, os pós fluxantes A e B foram investigados de acordo com diferentes propriedades físico-químicas. Diversos experimentos laboratoriais foram realizados para comparar o desempenho dos materiais A e B, visando à diminuição de captura da escória pelo aço no molde: avaliação do comportamento de fusão e fluidez, composição química e viscosidade. As temperaturas de processo foram avaliadas através de testes estatísticos, visando caracterizar o fluxo de calor e o trabalho de fricção durante lingotamento. Os testes industriais preliminares, realizados na Ternium Brasil, foram conduzidos com o objetivo de analisar o comportamento do pó fluxante durante a operação de lingotamento contínuo em relação a alguns aspectos operacionais e fornecer informações sobre sua influência na qualidade superficial do aço. Os resultados mostraram que, aumentando a viscosidade do fluxante, o consumo de pó tornou-se menor, levando a um maior trabalho de fricção e menor fluxo de calor no molde. No entanto, o comportamento da camada de escória mostrou que, apesar do aumento da força de atrito no molde, a espessura da escória foi adequada e não houve relatos de defeitos superficiais durante o uso do material fluxante de maior viscosidade.

Oct 1, 2019

By Patrizio Damiano

Competitiveness in Electric Arc Furnace production is pushing steelmakers to increase the throughput at the lowest expenditure. The technological challenge is therefore to operate the existing facilities at their top capabilities and to exploit materials and energy sources at the upmost yield and efficiency. Moreover, seizing the opportunity offered from the price variability of metallic feedstock calls for flexible practices, versatile equipment and tools to rapidly tune the melting profiles without hindering steel quality and equipment lifetime. The innovative Danieli Q-MELT Automatic EAF system addresses these aspects implementing a centralized control system which interacts with multiple technological packages. Each of these cutting-edge technologies focuses on one aspect of the EAF cycle, increasing machine availability and resource efficiency, by means of electrode regulation and foamy slag control, charging optimization, off-gas analysis and closed loop injectors control. Moreover, these modules provide the process supervisor application (Melt Model) with important information regarding the process status, thus allowing the adoption of a unified control strategy. The supervisor implements a robust statistical approach to identify process deviations in real time. The first results and technology perspectives inferred from the field immediately after the start-up are described in this paper.

Oct 30, 2017

By Qingwen Dai

The Marangoni effect is an important phenomenon where a surface tension gradient drives liquid towards high surface tension regions. Temperature gradient, evaporation, disparity of viscosity, and surface roughness and topography are all significant factors that can affect this thermo-capillary migration. The purpose of this study was to investigate the influence of micro-groove patterns on the migration of paraffin oil, and obtain a well-designed texture of micro-grooves to prevent the thermo-capillary migration. Patterns of micro-grooves with differing orientations and geometric parameters were fabricated on the surface of SUS 316 stainless steel substrates. Experiments on the migration behavior with different viscosities of paraffin oils were carried out various temperature gradients. The experimental phenomena indicated that the surface with the micro-grooves perpendicular or parallel to the temperature gradient have a strong impact on the migration performance of paraffin oil. Micro-grooves perpendicular to the temperature gradient exhibited extraordinary slower migration velocity than that of the parallel one. Width and depth of micro-grooves had an obvious influence on the behavior of temperature-driven migration and detail discussions on the effects of these geometric parameters were carried out.

Jul 31, 2018

By Pablo Bruno Paiva Leão

The present work is based on the characterization of nonmetallic inclusions in Ti stabilized ultra-low carbon steel, produced in a large steel mill. Due to a large incidence of submersed valve clogging in a continuous casting, the study is important in order to know the characteristics of the inclusions which are causing the problem. Total of 24 heats were sampled in the tundish and manually analyzed with a scanning electron microscope. The results revealed that 98.65% of the 3183 inclusions analyzed were solid in steelmaking temperature and 66.54% were alumina. The solid inclusions of alumina have low wettability for the iron bath, showing a high tendency of agglomeration in the submersed valves, affecting the castability. It has been concluded from the results and literature that some alternative measures such as the application of the treatment with calcium, precautions to avoid steel re-oxidation and the total or partial replacement of the pre-deoxidized element; would reduce the obstruction problem.

Oct 30, 2017