Search Documents

By Fernando Lopes Latorre

A cadeia produtiva do carvão vegetal que envolve as etapas de silvicultura, colheita e carbonização, tem passado por diversas mudanças nas últimas décadas. As produtividades volumétricas das florestas de eucalipto no Brasil aumentaram cerca de 4 vezes nos últimos 50 anos. A colheita florestal, nesse mesmo período, partiu de formas extremamente primitivas para máquinas de alta produtividade. Os processos de carbonização também evoluíram, mas sempre no sentido de aumento de produtividade dos fornos, com perda na qualidade do carvão vegetal produzido e sem aproveitamento integral da energia contida na madeira. Nesse contexto, esta etapa do processo chega a seus limites tecnológicos, ambientais e econômicos, ameaçando a sua sustentabilidade. Buscando resolver esse impasse, a Vallourec estudou o processo Lambiotte como base tecnológica para desenvolver seu ambicioso projeto de carbonização contínua com cogeração de energia em substituição ao processo artesanal de fornos retangulares de batelada. Esta tecnologia após vários anos de desenvolvimento demonstrou sua plena capacidade para atender a todos os aspectos demandados atualmente.

Oct 30, 2017

By Gabriel Mendes de Almeida Carvalho

O processo de soldagem de pontos por resistência elétrica é uma técnica econômica e adequada para a união de chapas, pela alta velocidade e adaptabilidade, torna-se um método amplamente difundido para a produção em massa. É utilizado principalmente em carrocerias de automóveis por apresentar elevada eficiência e qualidade. Este artigo analisa as diferenças apresentadas nas microestruturas de pontos de solda produzidos através do controle da refrigeração do eletrodo. Para garantir a qualidade de uma junta soldada e aumentar a vida útil do eletrodo é importante que os parâmetros empregados na soldagem sejam bem ajustados, para que o ponto de solda também apresente características que irão garantir uma boa performance do produto final. O objetivo deste trabalho é fazer a comparação da qualidade dos pontos de solda produzidos, além de avaliar a estrutura formada em diferentes temperaturas do eletrodo no momento da soldagem.

Aug 17, 2017

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017

By Douglas Glenn Stalheim

Production of structural hot strip coils in yield strengths up to 700 MPa and higher is increasing worldwide. In addition to requiring higher strengths, structural designs require good formability, toughness and weldability. Toughness and formability come from optimization of ductility properties while weldability comes from lower carbon equivalent alloy designs. The key to the production of optimized cost effective hot strip produced structural coils is to create the correct balance of a proper alloy/processing design to create as fine and uniformly distributed cross sectional grain size as possible. In addition to the creation of the fine/uniformly distributed cross sectional grain size, the correct microstructure needs to be created. In the higher yield strength grades, not only does the grain size/distribution play a role but a proper understanding and control of microalloying precipitation kinetics is required. This paper will present various examples of hot strip alloy designs to produce cost effective hot strip structural coil in yield strengths up to 700 MPa with good ductility and weldability. In addition, steelmaking/casting parameters will be discussed to assure successful production. Optimized reheating, rolling and cooling parameters of these alloy designs will be introduced in an accompanying paper.

Aug 17, 2017

By Pedro Cunha Alves, Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Julio Aníbal Morales Pereira

The capacity of steelmaking slags (CaO-SiO2-Al2O3-MgO) on inclusion removal from liquid steel was investigated through experimental conditions. Laboratory experiments with slag and steel samples (with inclusion population known) were performed using a vertical electric resistance furnace at 1600 ºC. After the melting experiments, slag and steel samples were separated and analyzed regarding their chemical composition and inclusion population evolution. The capacity of slags on inclusion removal was evaluated based on the thermodynamics (solid and liquid phases proportion, phase composition and effective viscosity of slags) calculated using the FactSageTM 7.2. Results indicated that changes in the composition of slags (regarding CaO/SiO2 e Al2O3) presented effects on the steel cleanliness. The total inclusion density decreased in all steel samples and the removal of inclusions by slags shows a tendency to improve as their viscosity decreases (< 0.23 Pa.s).

Oct 1, 2019

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Breno T. Maia, Débora C. O. Silveira, Mariana A. Ribeiro, Daniel A. G. de Carvalho, Roberto P. Tavares, Raissa S. Salgado

Mixing time is an important parameter when considering chemical and thermal homogenization in steelmaking reactors. It can also be relevant in the kinetics of chemical reactions. Different methods have been used to estimate mixing times in physical models of steelmaking reactors. In the present work a new method to estimate mixing times in physical models has been proposed. This method can be used when transparent fluids are used to simulate the liquid steel and the slag. Results of mixing times in a physical model of a BOF obtained with different techniques were compared. It was shown that the new method is more reliable and consistent than the common methods based on electrical conductivity measurements and colorimetric analysis.

Oct 1, 2019

By Eduardo Vitral

The present study focuses in the simulation of pattern formation by ion beam sputtering on a material surface. This process is responsible for the appearance of unexpectedly organized patterns, such as ripples, nanodots and hexagonal arrays of nanoholes. A numerical analysis of preexisting patterns is proposed to investigate surface dynamics, based on a model derived from a Kuramoto-Sivashinsky anisotropic equation, in a two dimensional surface with periodic boundary conditions. While deterministic, its highly nonlinear character gives a rich range of results, making it possible to describe accurately different patterns. A finite-difference semi-implicit splitting scheme is employed on the discretization of the governing equation. Simulations were conducted with realistic coefficients related to physical parameters (anisotropies, beam orientation, diffusion). The study dealt with a random and a monomode 1D structure initial condition in order to understand how the shape and wavelength of the initial pattern evolve with time. Ripples and hexagonal patterns were observed in the results, being physically consistent with the phenomenon. Moreover, the Method of Manufactured Solution has been used as verification of the developed numerical scheme.

Aug 16, 2017

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Antônio Aldenor Pinheiro Neto, Matheus de Lima Vieira

In mid-2015 the steel industry faced a strong crisis due to the weak performance of the Brazilian economy and the persistent entry of Chinese steel into Brazilian territory. This situation demanded that Brazilian steelmakers seek to develop products to meet new export markets. within the volume of exports possible are the rebars, where its applications are in the construction industry. One of the largest importers is Peru which has a large percentage of this export volume. This market demands as a priority requirement the surface quality of blue condition (low oxidation index) and mechanical properties normative.in order to meet the items required by the customer at a competitive cost, a vanadium microalloyed steel was applied to the hot rolling process without heat treatment after the last rolling pass. Where the great challenge was to achieve a high level of stretching without compromising the minimum limits of tensile strength. Assuming that the steel used is the correct one interventions were made on rolling parameters such as set-point temperature, residence time of pieces in the furnace, linear mass and rolling speed. All the changes made were based on statistical tools and practical tests. Finally, with the execution of actions generated from the statistical analyzes and tests it was possible to reduce process losses by 96%.

Oct 1, 2019

By Anna Carolina Cerqueira Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Aug 16, 2017

By Paulo Conceição, Carlos Sampaio, Carlos Petter, Ariane Kuerten

The Sensor Based-Sorting technology is an emerging technology applied in mineral separation and concentration. The technique consists in using a method known as Dual Energy X-ray Transmission sorting (DE-XRT). The particle's position over the conveyor belt was evaluated and, despite de variability of results, shows that there is no a position with greater accuracy on the sensor's reading. Results obtained indicated that DE-XRT sorting technology was able to significantly reduce the mass and the ash content of the ore feed, being an interesting option for reduction of costs and improvement of coal quality in beneficiation plants.

Oct 3, 2019

By Ernesto Furtado de Mello Neto, Eliezer Thuler, Claudio Vano Nunes, Carlos Alberto Cristofari

The Brazilian steel industry is dealing an adverse scenario with direct competition from global emerging markets. In this scenario, the need to improve asset operational performance, makes complex studies involving technical knowledge and asset life behavior, become important tools to support companies strategic accomplish. These studies allow consider performance, costs and operational risks relationship in the decision make process. The Asset Management approach support these studies in order to observe the whole asset life cycle, understand value chain through all company process and optimize the asset economic life. In this context, the present technical work has the purpose to support asset management decision making regarding ArcelorMittal Vega cold rolling drive motors, through the motors fail behavior modelling and estimated the risks involved in asset management decision. Through the Reliability, Availability and Mantenability (RAM) analysis, simulations were performed considering the failure, repair cost data and investments to build options to mitigate the operational risks.

Oct 9, 2019

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By G. Martino, F. Silva, Emmanuel Marchal

The definition of the chemical specification at multiple steps of the steelmaking process is very common in the industry. Among all elements and compounds, the Sulphur content has a special control over several stages, from the coal blend to the final products. Coke, iron and steelmaking specialists usually agree on a static specification for each intermediate product according to their local operation capacity and production cost. However, local decisions have major impacts on the whole production chain and many global factors should be considered in order to make the best decision. In this study, we will exemplify focusing on Sulphur content concepts and techniques that could be applied to many decisions in an integrated carbon steel plant. The variation of coal and coke prices, the desulphurization cost and time, the processes operating points, the hot metal rate at converters, prices and demands of low and ultra-low Sulphur steel grades are some of the integrated factors that are usually disregarded during the specification process. Mathematical modeling presents itself as a proper option into dealing with all the complexity that emerges from integrating all these processes' trade-offs and decisions. This study presents the results of a mathematical model that encompasses economic, thermal, chemical, and mass balances, physical quality of materials and productivity constraints of all processes of a hypothetical integrated carbon steel plant. It optimizes the iron and steelmaking process on a global and unique objective, dynamically defining targets for product quality to achieve the lowest steel production cost. This study details multiple market-plant scenarios in order to compare economic and operating results of a static vs dynamic specification practice.

Oct 1, 2019

By Wolfgang Kern

The implementation of the Gas Treatment Plant (GTP) for CSPECEM, Ceara-Brazil is a result of the closed partnership between Paul Wurth Italia S.p.A. and DMT, the German leading company in Coke Oven Gas Treatment Plants. In addition to technical issues reducing emissions, avoiding of waste and saving environment and energy were technical challenges during the engineering phase. Below mentioned three descriptions of technical solutions represents examples of a number other innovations based on DMT’s know-how and experience in the field of by-product plants. Generally the design of the complete GTP is based on the consideration of modern features and design upgrading, with the aim of a safe operation with stable conditions and a long-living cycle of the whole of the plant.

Aug 16, 2017

By Marcelo Rebellato, Beatriz Pereda, Beatriz Lopez, Pello Uranga

The classical application of Nb microalloying in the development of thermomechanical processes for flat products has been related to its suitability to enhance strain-induced precipitation and get a pancaked austenite prior to transformation. As new steel grades or new lay-outs are being developed, more complex metallurgical conditions need to be evaluated. In this context, Nb microalloying, alone or combined with other microadditions, needs to intervene in a more controlled way in additional steps of the thermomechanical process, besides its conventional strain-induced precipitation role. For example, the hardenability enhancement associated with Nb to properly achieve lower temperature transformation products, demands a proper balance of the Nb amount precipitated during rolling and the one remaining in solid solution. Similar effects are also sought when the final available Nb is used to increase strength through precipitation hardening. This manuscript evaluates how changes in the rolling strategies affect the interaction between Nb(C,N) precipitation and austenite recrystallization at different steps of the rolling process. As the possible interactions between parameters intervening simultaneously are quite complex, the application of microstructural models helps to properly define the best austenite conditioning combined with the convenient amount of Nb in solution, as a function of the final property requirements. Along the manuscript, several strategies will be discussed for the case of hot rolling of flat products comparing both normal and coarse initial austenite grain sizes.

Oct 1, 2019

By Cristiane Vilma Rocha Galiazzi

As matérias primas para Alto Forno devem ter qualidade física adequada para melhor controle do processo e estabilidade operacional. A distribuição granulométrica e consequentemente sua estabilidade são importantes, pois interferem na porosidade e permeabilidade no interior do Alto-Forno, criando assim uma condição adequada e específica de marcha com reflexo na estabilidade da produção de gusa. A Sinterização da ThyssenKrupp Companhia Siderúrgica do Atlântico (TKCSA) foi projetada sem britagem secundária, devido à fase de ajustes no processo operacional e baixa produtividade havia dificuldade para controlar a fração grossa do sinter (> 50 mm), impactando na distribuição granulométrica do sinter. Visando reduzir os desvios da qualidade física, estudou-se a melhor relação da altura de camada x velocidade da esteira encontrando um ponto de equilíbrio entre os níveis de produção e qualidade especificada que, juntamente com o início da operação do britador secundário, resultou na garantia da qualidade física do sinter para os Altos Fornos. Este trabalho tem como objetivo apresentar o desenvolvimento e resultados deste estudo.

Aug 1, 2018