Search Documents

By Luiz Henrique Accorsi Gans

First, this works carries an experimental evaluation for austempered ductile iron (ADI) as a gear material. And second, in order to provide a better understanding of the microstructural effect on the stress state of subsurface regions, a finite element method approach was considered using the submodeling tool in ANSYS 11.0. For this, ADI gears were produced from continuous cast iron bars, heat and thermochemical treated and tested in FZG test rig. The results were compared to those of carburized steel AISI 8620 and induction hardened steel AISI 4140 gears. The wear experiments were performed at the temperature of 90ºC with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state). The time for pitting and spalling on the gears surfaces were measured using image analysis. The results showed a very good potential of using ADI for manufacturing gears, replacing induction hardened steels. Also, the ADI gear with smaller nodules showed higher life for pitting. In contact fatigue tests with severe load, the carburized AISI 8620 steel proved more adequate than the austempered ductile iron, showing that the mechanical properties are critical in the resistance to damage in gear contact. The austempered ductile iron with smaller nodule size showed to be very competitive with wear resistance similar to AISI 4140 steel induction hardened. With ANSYS, it was verified that the nodule size affects the gears life independently of the mechanical properties of the matrix. The results showed that the nodules indicate the presence of a concentration stress, but their size doesn’t affect the contact fatigue life as much as the total amount of nodules, regardless of the ductile iron microstructure. The size and number of nodules affects both the nucleation and the propagation stage of cracks. ADIs with higher amount of nodules have a greater wear resistance. Also, compared to the Hertz contact theory (isotropic material), the presence of graphite nodules indicates a non-isotropic material and made the maximum shear stress point moves toward the surface.

Jul 31, 2018

By Ronaldo Câmara Cozza

Iron aluminide alloy; Ball-cratering wear testing; Rolling abrasion; Wear volume; Coefficient of friction

Jul 31, 2018

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By Rafael Arthur Reghine Giorjão

Microestrutura e propriedades mecânicas de tubos de aço inoxidável superduplex SAF 2507 processados por soldagem por atrito com pino não consumível foram analisadas. Juntas de alta qualidade foram produzidas com sucesso utilizando ferramentas de nitreto de boro cúbico policristalino (PCBN), controle de força de 38 kN, velocidade de avanço de 50 mm/min, velocidade de rotação de 200 RPM. Ensaios de dureza e tração foram realizados, evidenciando aumento de dureza na zona de mistura e falha no metal de base. Simulações térmicas calcularam temperaturas globais máximas em torno de 1176 °C e diferentes ciclos térmicos ao longo da espessura da junta, conferindo diferenças microestruturais e mecânicas nestas regiões

Oct 30, 2017

By Lara de Assis Moreira, Vinicius Thiago Lecco Rampinelli

The energy efficiency of reheating furnaces is a continuous challenge, as these equipment consume a representative portion of the total fuel of an integrated steel plant. Therefore, any investigation and implementation which brings improvement in this figure become an important issue for the mill competitiveness. In the case of production delays due to external factors (the condition addressed in this work), whether predicted or unforeseen, the slabs remain inside the furnace with high temperatures in order to avoid production delay during the production restart, elevating the specific consumption and scale formation. This work increased the energy efficiency of the two ArcelorMittal Tubarão’s walking beam reheating furnaces, by reducing the consumption of mixed gas during production delays (either scheduled or not) lasting less than 3 hours. The objectives were achieved through improvements, among them, tuning of Level 2 automation system parameters, automatization of procedures and operational training. The work resulted in a 34.4% fuel gas consumption reduction during the delays.

Oct 1, 2019

By André Oliveira

The present paper describes state-of-the-art Pulverized Coal Injection technology with focus to Dynamic Distribution guaranteeing highest accuracy on equal distribution and being thus one of the key factors enabling constantly highest injection rates. As an alternative to the construction of a new plant, existing plants may be modernized and upgraded to latest technology. Two recent examples are presented. As a conclusion, two case studies of return on investment are showing that the PCI technology, both for new facilities as well as for upgrades, is very profitable and mandatory for high blast furnace operation effectiveness.

Aug 17, 2017

By Fabiano Soares

Strand guide rolls in continuous casters are crucial components for guaranteeing an optimum process for the production of high-quality steel grades. The properties of these rolls greatly influence the quality of the slab produced. The most commonly used designs so far have been the axle roll and the solid roll. A quite new roll concept is the STEC-Roll®. It combines the advantages of the axle roll with those of the solid roll. This paper explains the development of this roll type and shows the current design. The characteristics of the STEC-Roll® are presented in greater detail and are underlined by a number of simulation results. Beside the design itself, the benefits for casting and maintenance are explained, including for example the easy assembly and dismantling or the use of the roll for dry casting. A brief examination is made of the TCO for the STEC-Roll® and an estimation is provided of the exchangeability of this roll. To conclude, an overview on the current applications is presented.

Aug 17, 2017

By Jeremy Fletcher

In today’s world, the requirement of Steel Producers to revamp and modernize their blast furnaces on-time, safely and with the latest technology is paramount. In addition they must meet the detailed design, construction and safety legislation and regulations, which can be different for the various countries around the world. Siemens MT is renowned for its ability to perform Blast Furnace rebuilds, relines and modernisations within extremely tight time frames and in a safe manner. Modular Blast Furnace construction concepts have been perfected to minimise project duration and plant downtime for furnace rebuilds. Safety and certainty are the keys for success. Siemens MT are constantly introducing new technologies into the market place including cyclone gas cleaning and triple external cone gas scrubber, along with step changes in technology such as dry gas cleaning and dry slag granulation. The economic environment and the continuing requirement for improved environmental performance, drive many of these innovations. This paper describes some of the latest rebuild reference projects of Siemens MT, along with the latest technical innovations installed on these furnaces, and some of the construction methodology used for a safe and secure rebuild.

Aug 1, 2018

By John Beaumont

The Plate-Steckel mill combines the asset utilization of the strip rolling process with the grade and width range of the reversing plate mill, delivering a broad range of steel products at low cost. Among rolling mill types, plate mills are distinctive in the way that they exploit the metallurgical attributes of their product. The downside of this flexibility, though, is a low level of asset utilization. The Plate-Steckel mill was originally developed to combine the utilization of the strip mill and the width of the plate mill. The Plate-Steckel mill is now setting new benchmarks in accessible grades and applications, whilst pushing the width boundaries of the process. Long experience in the Steckel process control and coiler furnace design is coupled with caster and plate mill expertise to deliver high level of performance in this increasingly important plate and coil rolling technique. Several new design features have been incorporated and the vertical integration of mechanics with process models is the key for better product quality and flexibility at these plants. The use of fully automatic thermo-mechanical rolling using the latest physical models and intelligent sequencing strategies achieves the optimum grain refinement and thus improves mechanical properties. The novel profile and flatness strategy relies on comprehensive physical models and makes use of SmartCrown® as a powerful actuator, enabling large reductions to be taken without risking poor flatness. Throughout the rolling and cooling stages of processing, accurate calculation of the thermal-mechanical state of the product is performed by the temperature monitor. This enables tighter control of the final plate mechanical properties by providing an insight into the plate evolution during the thermo-mechanical processing. Advanced pacing functionalities provide an optimized mill throughput, utilizing new cooling bed charging strategies. Considering the rolling process, process automation applies state-of-the-art model calculations to achieve saleable coil/plate target dimensions even in non steady state rolling conditions.

Aug 16, 2017

By Enif Gutiérrez Guerrero

Inclusion deposition is still a standing problem in the continuous casting of steel since the deposition of alumina inclusions inside the SEN affects the productivity and the product quality. The present work studies the factors involved in the inclusion deposition at the nozzle and the effects of inertial, gravitational, buoyant, pressure gradient, and Saffman forces on the inclusion trajectories. The results show that the inclusions reaching the nozzle, only 30% get deposited along its walls mainly at the Upper Tundish Nozzle (UTN). This area of higher deposition is identified close to a low static pressure and a high turbulent kinetic energy dissipation zones where the effects of the gravitational and buoyant forces do not promote a significant inclusion radial movement since these are aligned with the direction of the flow stream lines. In contrast, in this zone, the Saffman force shows an important effect on the deposited inclusions, slowing down the inclusions in the vertical axis and increasing their radial movement.

Aug 17, 2017

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the virgin condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 69 to 258 MPa producing rupture times varying from 8 to about 4908 h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results mentioned in literature for the same material in the virgin condition.

Aug 16, 2017

By Jörg Thomasberger

Delivering liquid steel to a steel processing unit at right temperature is an important criterion for high production steel shops, but it is surprising how little attention has been paid in the past to manage this vital phase in the steelmaking process-the steel in transit. The ladle running costs, both directly and indirectly, contribute significantly to the cost of steelmaking and should be an area of concern to any high production steel plant. Here we are talking not only of refractory costs or preheating fuel costs, but also cost of extra heating in ladle furnace, additional process delays incurred in delivering steel at right temperature to downstream unit in case proper care is not exercised at upstream unit, and occasional costs of ladle breakout due to inability to judge the residual life of the ladle. This paper emphasizes the need of a comprehensive ladle management system, an aspect which has not been properly addressed in the operations of a steel plant, in improving the productivity of a steel melt shop. Starting with review of present status and the attempts at implementation of ladle tracking in steel melt shop automation system, it looks at components of an exhaustive Ladle Management System (LMS), and finally gives an idea of benefits that will accrue from implementation of such a system in a steel melt shop.

Aug 17, 2017

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017

By J. Kempken

Driven by customers, especially from the automotive sector, the supply of 100% prime quality has become essential. Furthermore the implication of quality costs and the yield of first class products define the steel companies' profitability and overall success significantly. The SMS group together with its subsidiary MET/Con has developed a comprehensive solution to assess the product quality over the production and processing chain. Process and production parameters originating from various data sources of the process automation are examined on their impact of quality related characteristics.Expert know how and comprehensive operational experience is translated into a quality guideline and a regulation framework as the sensitive core of the PQA solution.Once implemented, the system identifies immediately steel grade specific, deviations from ideal standard and proposes corrective actions including a final evaluation for each product at each processing step.The X-Pact® PQA (Product Quality Assessment) system is a substantial tool for root cause quality analysis and provides the required support to the production team. It will become an integral part of the corporate quality management system.

Aug 17, 2017

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Aline Lima da Silva

The reduction in SOFC operating temperature due to recent development in materials and fabrication techniques enables the use of ferritic stainless steels as interconnects for SOFCs. Ferritic stainless steels offer many advantages over traditional ceramic interconnects, such as higher thermal and electronic conductivity, as well as relative ease of fabrication. However, the formation of chromium oxide on ferritic stainless steel results in an increase in ohmic resistance and can lead to the loss of cathode catalytic activity (due to Cr volatilization, with cathode poisoning). The oxide growth depends on several factors, such as steel composition, temperature, oxygen partial pressure. In this way, knowing the phase stability, the oxidation behavior of the material and the oxidation kinetics is of great interest. In this context, a thermodynamic study of the oxidation of ferritic stainless steel 430 under oxidizing atmosphere (cathode), at the temperature of 750ºC, is carried out. As one can see, the thermodynamic system can be very complex, involving several phases (chromium oxide, (Fe,Cr,Mn)3O4 Spinel, iron-chromium oxides, etc.). The effect of oxygen partial pressure and alloying elements on phase distribution is evaluated. Thermodynamic modeling is compared with experimental results from literature.

Aug 8, 2018

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By Samuel Filgueiras Rodrigues

An austenitic stainless steel ISO 5832-9 was deformed in a torsion test machine over the temperature range of 1,000°C – 1,200°C and strain rates of 0.05, 0.1, 1.0 and 5.0s-1. The Steel plastic behavior was studied by analyzing the flow curves shapes and using the constitutive equations under the conditions of thermomechanical treatment. The curves initially presented an increase in stress characterized by hardening work, followed by a drop in stress to an intermediate level that reached or not, for certain conditions, the steady state softening. The plastic flow curves of ISO 5832-9 steel displayed in three different ways: (i) Curves with continuous softening presenting plastic instability for low temperatures and high strain rates; (ii) curves type flat, here after the peak there is little variation of stress with strain presenting softening mechanism by higher contribution of dynamic recovery at low temperatures and low and intermediate strain rates; (iii) curves with softening after the critical deformation favored by high temperatures and low strain rates. These behaviors indicate the influence of the stacking fault energy (SFE) and precipitated particles on the softening kinetics of this steel.

Aug 8, 2018