Search Documents

By João Alberto Fioresi Altoé

Nas indústrias petroquímicas, nucleares e farmacêuticas o avanço tecnológico tem como objetivo a segurança e confiabilidade dos equipamentos com relação à resistência mecânica e à corrosão. Atualmente, o uso dos aços inoxidáveis superausteniticos é uma solução interessante, para uma maior vida útil dos componentes industriais submetidos a ambientes agressivos, como em meios salinos. Esse trabalho tem como objetivo investigar o aparecimento de pites em um aço comercial superaustenitico de composição química aproximada 25Cr28Ni4Mo em solução salina de cloreto de sódio. O aço foi fundido e tratado termicamente por solubilização a 1050ºC por 1h com o objetivo de eliminar os precipitados. As análises microestruturais antes e após os ensaios de corrosão foram feitas por microscopia óptica e eletrônica de varredura. Observou-se com os ensaios eletroquímicos de Polarização linear e impedância, que o aço inoxidável superaustenítico apresenta excelente resistência à corrosão em meio salino, caracterizado também pelas imagens que não revelaram a formação de pites, mesmo quando submetidos a elevados potenciais.

Aug 16, 2017

By Luiz Carlos Teixeira Brandão

O Alto-Forno 3 da Usiminas em Ipatinga, que atualmente está na sua quarta campanha, apresenta 30 ventaneiras. Nesta campanha houve alguns eventos de arrombamento e avermelhamento dos algaravizes. A causa destas ocorrências são obstruções das frentes de combustão das ventaneiras, gerando diversos transtornos operacionais. A fim de se evitar novos fatos semelhantes foram desenvolvidos alguns sistemas de monitoramento das frentes de combustão. Dentre os sistemas desenvolvidos se destacam o diferencial de pressão do conjunto de sopro; e, o controle da temperatura do conjunto de sopro. Os sistemas desenvolvidos permitiram maior confiabilidade nas ações imediatas dos operadores em anormalidades na zona de combustão com consequente ganho em desempenho operacional do alto-forno.

Aug 1, 2018

By Andrea Zanon

Recently steel manufacturers have significantly focused their attention on safety and working conditions thanks to new labour laws, comprehensive operators’ knowledge and increased company social responsibility. Even with a reduced budget, investments on safety are now widely approved. Mill constructors aim at developing upgraded solutions to comply with these new requirements. In some cases mill constructors can even anticipate customers’ requests and consequently put into the market innovative solutions. In this text we will analyze some advanced solutions developed by Danieli & C. Officine Meccaniche Spa - the leading company in long-product rolling mills - aimed at improving working conditions on wire-rod block settings. In particular, we will focus on rolling guides installed on fast-finishing blocks and on servo-assisted device for rolling rings changing. In fact, this equipment has shown effective benefits on our test plants and has mainly cut out the tendency of the personnel to be absent due to backache. This paper will first present standard working conditions, will then introduce the newest equipment developed by Danieli & C. Officine Meccaniche Spa, will analyze its operation and finally will describe in detail the benefits that can be reached with its use.

Jul 30, 2018

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By LJ Aspinall, Paulo Sérgio Soares Santiago

Monitorar adequadamente a qualidade da água em sistemas de resfriamento é fundamental para assegurar um bom condicionamento de seus indicadores chave de desempenho: a corrosão, a incrustação, a formação de depósitos e a atividade microbiológica, de forma que as unidades operacionais possam atingir suas metas com relação aos seus respectivos índices chaves de performance do processo industrial. Enquanto a confiabilidade deste monitoramento em antever problemas assume, então, elevada importância, os métodos utilizados até o presente na indústria não têm efetivamente fornecido resultados realísticos pela ausência de troca térmica nos dispositivos usados. A Knew Value desenvolveu e patenteou uma nova tecnologia, o Sentinel, que permite aplicar métodos inovadores de monitoramento on-line, permitindo realizar simulações em condições críticas de velocidade de escoamento e temperatura de película e atingindo excelência em monitoramento de indicadores chaves de desempenho do tratamento químico aplicado em sistemas de resfriamento. O objetivo deste trabalho é apresentar esta tecnologia e casos históricos de desempenho.

Aug 1, 2019

By Jens Kempken

A competitive landscape pressurizes the steel producers business, zero defect requirements from customers forces the operators for additional efforts in process control and quality management. The so called quality related cost, which include also rework, cost for downgrading or even scabbing of material is already a remarkable lever in a plants profitability breakdown. The introduction of advanced state of the art grades in the product portfolio requires already a budgeting for the expenses for R&D and quality management. PQA has been developed as a process and quality management software solution next to existing level 2 or level 3 automation systems. It is focusing on the analysis of process data, equipment information, in line quality measurement devices and trend analysis to obtain an answer whether the process is according to definition and expectation and whether the intermediate or final product can be shipped for further processing as prime material. Advanced analytics which are linked to an expert know how based configuration identifies deficiencies in the production and processing process. An intelligent, state of the art quality rating system evaluates tolerable deviations. PQA comprises the software platform including the database, data configurator and collector from the different sources in the production process and units. The core element of the platform is the knowledge based expert know how package defining process and quality determining fundamentals. The paper describes the structure of the software package, it gives insights on the expert know how package, process and quality evaluation and points out the customer benefits, cost reduction, improvement yield, customer satisfaction increase. The link to recent operational references is given.

Oct 30, 2017

By Humberto Napoli BELLEI

O Sol é a principal fonte de energia sustentável com enorme potencial na geração de energia elétrica. O Brasil como outros países do mundo estão começando a construção de fazendas solares. Atualmente as especificações das estruturas para construção das estruturas dos painéis utilizados nessas fazendas tem sido de aços pós galvanizados justificado pela questão de tempo de garantia, principalmente, devido a presença de furos e bordas que ficariam protegidos contra a corrosão pela grande quantidade de revestimento utilizado. Nesse trabalho serão apresentados resultados de um aço pré-galvanizado que se mostrou seguro e confiável na proteção contra a corrosão dos furos e bordas dos painéis. O estudo teve como base as informações obtidas após o aço ter sido testado no ensaio em câmara de névoa salina e de dados já conhecidos em ensaios de campo.

Oct 30, 2017

By Felipe Poffo, Flávio Messas

Due to the high level of competition in tooling sector, a necessity to increase the level of processes and assets management has initiated. Based on the World Class Manufacturing methodology, applied mainly in serial production industries, we have challenged ourselves to adapt the main concepts and implement them in a tooling company. After one work year, we could notice 29% productivity improvement in the bottleneck process, 25% cost reduction in outsourcing, standardization of the processes, 8% reduction in direct labor. Consequently, it was possible to implement a financial reserve and a long term planning cash flow.

Nov 22, 2018

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Daniel Valente Guimarães

Este trabalho tem como objetivo apresentar os resultados alcançados através do planejamento, por meio do agendamento com hora marcada, no processo de expedição de produtos acabados, que estão permitindo a Votorantim Siderurgia atratividade na contratação de veículos, redução de custos e confiabilidade no processo.

Aug 17, 2017

By Franz Ramstorfer

No lingotamento contínuo de placas, rompimentos de veio pelo colamento e problemas de qualidade de superfície, como trincas longitudinais, são frequentemente relacionadas à lubrificação insuficiente no molde de lingotamento contínuo devido ao pó fluxante ou a prática de oscilação inadequados. Para detectar, com vistas a prevenir, este tipo de problema de processo, um método para avaliar em tempo real o coeficiente de atrito entre o veio e as placas do molde foi desenvolvido, utilizando-se a medição da força que atua nas placas laterais do molde e as forças de oscilação. Observou-se que o coeficiente de atrito do molde é um parâmetro confiável para auxiliar no desenvolvimento de pó fluxante, na otimização de parâmetros de oscilação e no monitoramento online do desempenho de pó fluxante.

Aug 16, 2017

By Gustavo Nucci Franco

A indústria do aço passa por seu pior período no Brasil e as empresas vêm buscando soluções para minimizar custos e garantir as operações com menos recursos. Ponto importante nessa busca de ganhos potenciais, a Logística vem, assim, merecendo uma atenção especial. Este trabalho apresenta esforços da AM Juiz de Fora, em parceria com a Franco Arbeit Engenharia, para reduzir o tempo de permanência de veículos em sua unidade e, com isso, evitar custos com o pagamento dos novos valores de permanência. Para isso, foram utilizadas modernas ferramentas de Simulação em Computador para que as soluções mais adequadas pudessem ser implementadas com sucesso.

Aug 17, 2017

By Guilherme Lisboa Quaresma

Um ensaio por partículas magnéticas é um método não destrutivo utilizado na detecção de descontinuidades superficiais e subsuperficiais em produtos laminados. Este método consiste em submeter a peça a um campo magnético, com aglomeração de partículas magnetizáveis nos pontos onde há descontinuidade. As partículas usadas podem ser de diferentes cores, dimensões e formas. A partícula fluorescente sob a luz ultravioleta demonstra melhor resultado para detecção de pequenas descontinuidades. Para ampliar o campo de visão ensaiado e realçar o contraste entre partícula e peça a radiação ultravioleta deve garantir uniformidade, intensidade e comprimento de onda adequado. Essas exigências motivaram o trabalho da Gerdau junto com a Metal Chek, representante da Spectroline, no desenvolvimento de uma solução inovadora. Na Linha de Inspeção de Tarugos da Gerdau Ouro Branco o uso de luminárias ultravioletas de LED - Light Emitting Diode tornou-se uma alternativa que proporcionou ganho em eficiência e em confiabilidade na tomada de decisão do inspetor de qualidade, baixo consumo de energia, custo de manutenção e satisfação dos clientes. A implantação das luminárias de LED refletiu na prática a evolução da qualidade do produto, além de melhores condições em meio ambiente, saúde e segurança para o inspetor.

Jul 30, 2018

By Georg Keintzel

The origin and elimination of 3rd octave mill chatter is a frequently investigated topic since tandem cold mills are in operation. So far only chatter monitoring systems have been successfully deployed, but this implies speed reductions and therefore a significant loss in mill output. Primetals Technologies has developed a new system using active injection of damping in order to eliminate 3rd octave mill chatter. The new hydraulics-based ChatterBlock® Control has now been proven successfully in mill operation. 3rd octave mill chatter, typically occurring in a frequency range between 90 and 150Hz, is a self-excited vibration phenomena typically occurring in the rear stands of tandem cold mills. It can produce significant gauge variations and even cause strip breaks. 3rd octave mill chatter is characterized by a quickly diverging vertical vibration of the rolls for specific rolling conditions (material, mill speed, forces, gauge etc.). Its occurrence requires immediate speed reduction of the mill in order to avoid strip breakage and/or strip quality degradation. This phenomenon thus severely limits mill productivity. The first step to proof the industrial feasibility of the new system was its installation on stand no. 4 of a 5-stand tandem mill. The development process and first results of the industrial implementation will be presented in this paper.

Aug 16, 2017

By Christoph Aichinger

The optimization and improvement of a modern integral iron and steel works gets more and more difficult as each individual plant is already operated at its best efficiency and at the lowest operational expenditures. However very often the individual plants are considered as stand-alone units and there are losses and inconsistencies on interfaces and take over points, which could be avoided and by that improving the overall performance of the iron and steel works as a holistic unit. Primetals Technologies looked into this subject extensively in the recent years and is now ready to offer new tools and services in order to assist operators to find further potential for improvement in processes, which seem to be fully developed at first sight.

Aug 17, 2017

By Elena Kalinin Toss

Inúmeras indústrias necessitam de sistemas de tratamento de água que favoreçam o processo de descarte de seus efluentes, além do aproveitamento do reuso de água. A mineração e siderurgia podem apresentar rejeitos com metais, que necessitam de tratamentos econômicos e sustentáveis. A biossorção é um exemplo de técnica que vem ganhando interesse em diversas áreas da pesquisa. O objetivo do estudo foi avaliar a porcentagem de remoção de íons de níquel de uma solução monoelementar de cloreto de níquel II (NiCl2+) em pH 2, 4 e 6. Para isso, utilizou-se um sistema de batelada, e 1g de consórcio bacteriano liofilizado (sem ser autoclavado) isolado de amostra de terra. Os resultados indicaram que a eficiência da biossorção foi maior para o pH 6, e que o consórcio bacteriano foi eficiente na remoção de íons de Ni2+.

Oct 30, 2017

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Ron Webber

With the difficult economic challenges currently facing the steel industry, it is essential to perform a complete analysis when determining which rolls to purchase. A properly designed “Total Cost of Ownership” model can result in significant savings. This paper will review the costs associated with rolls in both Hot Strip and Cold Strip Mills. The multitude of factors that must be considered in performing a complete analysis for the roll purchasing process will be discussed. Models for both Hot Strip and Cold Mills will be presented. Examples where traditional analysis can lead to expensive, incorrect decisions will be presented.

Oct 30, 2017

By Juergen Meisel

The paper will explain how to successfully implement a robotic solution from the initial idea to a working industrial solution. Primetals Technologies can call upon 10 years of experience in installation of Robot solutions in the harsh environment of steelmaking plants - the so-called LiquiRob. To enhance an existing shroud manipulation system, the idea to connect the shroud with a bayonet mechanism to the ladle nozzle was born in accordance with the requirements of a well-known steel producer. The paper will describe the development steps from the first simulations and prototype testing in the laboratory, it will show the intensive system testing under workshop conditions and will finally depict the successful integration into the plant. Furthermore, operational experience will be shown as well as the advantages of such an installation compared to other shroud manipulation systems.

Oct 30, 2017