Search Documents

By Adriano Gonçalves dos Reis

In the development of the structural materials for the advanced applications, as in the aerospace industry, there is a constant strive to increase both strength and toughness. Maraging steels are iron-nickel alloys designed to combine both properties that are achieved through the age-hardening of low carbon martensite. This alloy have a metastable martensitic structure that can revert to austenite when heated in temperatures close to the aging temperature, and this effect can be enhanced with the temperature increasing and time of treatment. Therefore, the study of creep behavior in elevated temperatures has technological importance to the development of this material. In this work the creep behavior of a maraging 300 steel solution annealed is evaluated by carrying out creep tests at 650ºC and in a stress of 200, 300 and 500 MPa. Creep parameters, such as steady state creep rate (?????), final creep time (tf), and stress exponent from secondary creep (n) are determined, considering that they are important to evaluate the creep resistance of the material.

Aug 7, 2018

By Alberto Tremea

The eddy current system is universally recognized as a most suitable method to point out discontinuities or modifications on the roll surface. The automation of the controls through the implementation of sophisticated equipments on the grinding machine has favoured its employment in the roll shop. A big effort is still going on to clarify the best way to promptly identify situations that could be really unsafe for the roll life. The results presented in this paper have been obtained through an intensive activity conducted in field by Innse Cilindri on work rolls of finishing stands of hot strip mills. The correct interpretation of the eddy current signals and a good calibration of the automatic system have allowed, in many cases, a substantial optimisation of regrinding practices.

Aug 16, 2017

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Enrique Francisco Somolinos Garcia-Morales

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 1, 2018

By André Luis Martins de Souza

O objetivo do estudo foi medir e aumentar a produtividade das equipes de manutenção - em uma mineradora multinacional - dentro e fora das paradas de manutenção, avaliando os principais fatores que influenciam o indicador e, ainda, reduzir os custos de manutenção referente a contratação de efetivo terceirizado através da inovadora metodologia Six Sigma, para este trabalho utilizou-se um metodo quantitativo, analítico e experimental. Após a finalização do projeto obteve-se o aumento da produtividade da equipe de manutenção em todos os turnos analisados e os custos foram reduzidos em aproximadamente R$ 200.000,00 e o tempo para resolver pendências que era de 50,1 dias foi reduzido para 18,1 dias.

Oct 30, 2017

By Vinicius de Oliveira Fidelis Sales

O presente trabalho tem como por objetivo a busca por uma solução eletrolítica capaz de eletropolir, eficientemente, amostras de ferro puro (>99,8% Fe). A finalidade de se utilizar o ferro é devido o interesse em suas propriedades biocompativeis e a sua possível aplicação biomédica, sendo utilizado em dispositivos biodegradáveis. Ligas à base de Fe, Mg e Zn estão ganhando importância devido às vantagens que elas oferecem, em comparação com as tradicionais (AISI316L, L605), sendo a capacidade, de se degradarem a principal caracteristica. A escolha do eletropolimento, como técnica de modificação de superfície, deve-se a sua capacidade em polir o material tornando o seu relevo mais homogêneo, garantindo um pré-tratamento adequado ao material em diversas aplicações, como por exemplo o tratamento com o plasma. Um dos grandes diferenciais desta técnica é que pode ser utilizada em materiais com geometria complexa. Foram realizados testes utilizando um grupo de 4 soluções presentes na literatura e analisados os seus efeitos em amostras de ferro puro. Com os resultados obtidos pelas análises de Microscopia Óptica, Microscópio de Força Atômica e Ângulo de Contato foi possível verificar que a solução 2C obteve o eletropolimento mais efetivo, apresentando assim as características desejadas.

Oct 30, 2017

By Alexandre Gonçalves Andrade, Crisley Dellaqua Pacheco, Gabriel Miranda Teixeira, Aline Maria Santoro Nasaré, Tatiane Ferreira Alvarenga

Diffuse emissions are that directly related to particulate matter suspended from civil structures, materials disposed in conveyor belts carried out by wind, stack e reclaimers operations and that one where dust collectors are not able to act correctly. Vale implemented in the last years a unique system capable to measure this kind of dust, called RAMPs (Dust Monitoring Automatic Network), which creates an analytical net in Tubarao industrial site, located in Vitória, ES. In order to prevent diffuse emissions in Tubarao’s pellets stockyard, it was proposed and developed a predictive model based on operational and climate variables available on the site, using big data and advanced analytics tools. The models developed shows to be adherent to the real emissions rates measured by the RAMPs and proved to be an efficient tool to predict emissions over the internal target with 4 hours of precedence.

Oct 1, 2019

By Vinícius da Silva Madruga

Os processos de lingotamento contínuo e de lingotamento convencional apresentam diferenças na solidificação dos aços, esse fato tem impacto na distribuição, quantidade e forma de inclusões de óxidos e sulfetos. O objetivo desse trabalho é verificar de que maneira tais diferenças influenciam na distribuição dos sulfetos ao longo do aço solidificado de qualidade SAE 1050. Para isso, 20 amostras foram retiradas de eixos forjados e barras laminadas, produtos conformados de origem do lingotamento convencional e do lingotamento contínuo, respectivamente. As amostras foram analisadas em microscópio ótico e microscópio eletrônico de varredura no modo de análise automatizada de partículas. Através das imagens e de dados numéricos obtidos, foi visto que nas amostras de barra laminada há grande quantidade de sulfetos, se analisada na seção longitudinal, em relação às amostras de eixo forjado. Analisando na seção transversal, foram detectados menos sulfetos devido ao alinhamento dos mesmos. Entre as amostras de eixo forjado, a área ocupada pelos sulfetos é maior no pé do lingote, reduzindo em direção à cabeça, apesar de a cabeça apresentar mais sulfetos. Tais diferenças foram atribuídas à taxa de resfriamento, à seção transversal do produto e ao processo, que variam entre os dois tipos de lingotamento.

Oct 30, 2017

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Luana De Lucca de Costa

Este trabalho é um estudo sobre os aspectos tecnológico de sinter forjamento, onde são realizadas alterações nos parâmetros temperatura e deformação. Experimentos foram realizados para o estudo das variações microestruturais, e propriedades, tais como, densificação e dureza, e, ainda, quais as variações na força empregada para obtenção das deformações estabelecidas. A relação entre a tensão de atrito na interface e outras variáveis do processo é discutida e uma análise feita para o cálculo da distribuição da pressão e carga a partir das equações de equilíbrio. Os resultados são discutidos e os parâmetros de processamento envolvidos durante o processo de sínter forjamento são analisados.

Aug 8, 2018

By Luiz Gustavo Franco Amaral

The recent tragedies that occurred in Brazilian territory had a greater impact than that presented in the major newspapers and led an entire industry to question the technology and techniques that were previously practiced in the mining industry. With this, there is the prospect of new projects and innovations in the most varied branches of engineering. This publication presents computational technologies to support the decision making of engineering projects aimed at the mining sector and explores the benefits obtained from the use of current technologies in the mining sector. Recent works are referenced in order to propagate not only the methodology employed in these researches, but also to provide the reader with an overview of the industry and companies that invest in technology to support their decision making in the most diverse projects gains on products and processes obtained through this practice.

Oct 3, 2019

By Beatriz Dogliani, Elisabeth Williams, Maria Berenice Sandobal, Carina Bertino

The environmental management of steel mill slag should be understood as a management philosophy, observing technical, economic and environmental criteria associated with their generation, storage and final destination. The slag can be considered as a synthetic mineral resource and become a very useful co-product in different areas. The Argentinean steel industry prioritizes the efficient environmental management of its waste, thus contributing to its own survival taking into account the sustainable development. In the world, the slag produced by the steel industry has been used as steel aggregate for road bases, railway ballast and filling material among others. Any factor that influences the economy of the country affects all branches of society, mainly public agencies, whose financial resources are increasingly scarce to deal with all public works. It is necessary to join efforts of private and public initiative in the adoption of alternative materials that replace the use of finite natural resources. This presentation aims to show the work done by private companies together with public bodies and universities to obtain a regulatory document for the management of slag as steel aggregates for three different uses, namely: road use, railway use and general use.

Nov 5, 2019

By Michael McDonald

The cold-rolled steel output of cold-rolling mill (CRM) complexes are sometimes constrained by their batch annealing facilities (BAF). This paper examines a cost-effective solution to increasing capacity and quality of the BAF thereby making additional capacity available for CRM output. The solution involves applying a structured system of scheduling and operation to the BAF, using a proven level-2 software model. The system presented has been applied to a wide variety of BAF with all the leading furnace brands. Whether using traditional HN atmosphere or 100% hydrogen, peak performance can be achieved when using a properly configured, on-line, physical thermodynamic model. Given that it is not practical to place a thermocouple in each coil that is being annealed, various methods have historically been used to estimate the time required to properly anneal all the coils in the charge. This paper examines how the latest technology, in wide use throughout the USA, uses a physical thermodynamic model to shorten average cycle times, thereby increasing productivity and reducing energy consumption. The paper also examines the benefit of building thermodynamically balanced charges to further optimize the BAF operation and improve quality consistency by decreasing mechanical property variations.

Jul 30, 2018

By Mário César Mantovani

The steel for gas turbine compressor discs (26NiCrMoV14.5) requires some mechanical properties like strength, impact, toughness, fatigue, and creep resistance in order to be used in such application. To achieve the properties required for the gas turbine compressor discs, the material should have very low contents of sulfur, phosphorus, antimony, tin and arsenic. The level of cleanliness should also be very high and this is possible by achieving low oxygen content keeping the deoxidation elements like silicon, manganese and even the aluminum in very low percentages. The main problem in refining such steel is to adjust a sufficiently low oxygen content to have a good desulfurization and at same time a good cleanliness without using silicon, manganese or aluminum as deoxidizers. Combination of initial selection material, steelmaking process control, forging sequence and heat treatment cycles can provide uniform mechanical properties throughout the gas turbine compressor discs. Villares Metals SA as a big player on special steels with complex process has been developing this kind of material for several years. The objective of this work is to show the process technology evolution involved in the production of this kind of steel under the discussed preconditions.

Aug 17, 2017

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By Jefferson Lisboa Lelis, Marcos Roberto Soares da Silva, Maiara Rodrigues Gouveia

Nowadays, due the development of new hot rolled strips at USIMINAS, established the necessity of realizing studies to define new parameters for the welding machine of new pickling line, in order to improve mechanical and metallurgical properties of these materials. The aim of this study was to evaluate the weldability of high strength low-alloy steel with low boron content with tensile strength above 600MPa.The influence of energy input and preheating temperature on the mechanical properties of hot rolled strips were analyzed at three distinct thickness (2, 4 and 6 mm). To perform these evaluations were used tensile test, micro-hardness, metallography (micro and macro examination) and scanning electron microscopy analysis. In resume, a good welding performance was achieved, increasing preheating temperature and the welding energy higher than 60%.

Oct 13, 2019

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Leonardo de Souza Melo, Giovani Rodrigues, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipment in 2015. In addition to improving productivity related to these new equipment, several additional jobs were planned and executed on equipment already installed has been carried out in order to improve the efficiency of the line. The present work exposes what was done in the scale breaker (tension leveler) to improve the availability results of the section and consequently of the line.

Oct 1, 2019

By Wolfgang Linden

One of the most important factors in successful electric steelmaking is the continuous observation of the process and the reaction to it. Traditional electric arc furnace control uses mainly direct controls which are based on the electric power input. Not considering the furnace conditions will necessarily lead to suboptimal operation in terms of energy consumption and productivity not fully utilized.The ARCCESS FEOS (Furnace Energy Optimization System) includes the simultaneous control of the transformer tap, impedance operating point, reactor tap, burner and carbon injection, and DRI charging control. FEOS has proven in practical operation benefits of high melting yields, no interruptions through switch offs in borderline temperature area, rapid reaction, reproducible and efficient electrical energy input and short power-on times.

Jul 30, 2018

By Fernando Hernández Polanco

Transportation and handling metals and alloys from mills to consumption factories as well as dosing in conventional processes with ingots and scrap has always been considered a complicated activity with high operating costs. Several manufacturers of ferroalloys willing to solve these problems have chosen an alternative for their products that can be used to secure, during transport and dosage in the processes to making special steels, with more efficient consumption of ferroalloys. The trend for the production and sale of ferroalloys is to provide the product in the form of granules packed in bags or in bulk. In this paper we will show you how the granulation process was developed and rapidly adopted the ferroalloys industry as an effective solution to reduce operating costs, create cleaner and safer working environments.

Oct 30, 2017