Search Documents

By Luciana Lezira Pereira de Almeida

With the increasing use of ornamental rocks, mainly in civil construction, sundry problems were identified in relation to rocks cutting, such as efficiency in the cutting process and rock quality lumber. In recent years several composites have been developed to solve these problems. In this context, the study of the binomial matrix metal-diamond interaction is of paramount importance for the development of new composite materials to improve the efficiency of the cutting tool. The diamond impregnated matrix metal often reveals a reaction between the diamond surface and the matrix. Besides the mechanical connection, chemical reactions can sometimes occur. Therefore, this study aims to assess the achievement of diamond composites in the system Fe / Cu / Ni / Sn via powder metallurgy, with added CRB2. Analyzes have been performed to characterize chemical / physical and mechanical. The results have showed that addition of CRB2 promote significant changes in the properties of composites, especially in wear resistance and fracture toughness. Furthermore, the presence of the composite CRB2 causes a significant improvement in thermal stability.

Aug 16, 2017

By Lucia Vieira

Kelvin probe force microscopy (KPFM) can be used to monitor electrostatic charges on the surfaces of materials. In this paper, we describe the use of KPFM to evaluate the electrostatic effect induced by silver nanoparticles incorporated as clusters in diamond-like carbon (DLC) films, before and after scratching. The results are compared to those obtained for DLC films without silver nanoparticles. Raman spectroscopy was used to identify the DLC signature, and energy dispersive X-ray spectroscopy (EDX) was used to confirm the presence of silver in the film. The morphology of the DLC film containing silver was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings suggest that the incorporation of silver nanoparticles in amorphous materials could offer new options for electrostatic energy storage on the surfaces of these materials.

Jul 31, 2018

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Michel Fillon

Hydrostatic assistance is a commonly used method to improve limited load carrying ability of tilting-pad thrust bearings during transient states of operation of the vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves etc.), it also requires manufacturing of special recesses/pockets at the pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up of the machine and form a hydrostatic film between the pads and the collar. There is a quite wide variety of geometry of recesses (shape, depth, size) met in practical large bearing applications. The presence of a hydrostatic pocket (usually located in the sliding surface above the pivot area, where thin film, high oil pressure and temperature are observed) affects bearing performance under hydrodynamic operation. In theoretical researches, there is an almost common practice not to include hydrostatic recess in THD or TEHD analysis. This is probably due to the problems with obtaining solution for oil film geometry with pocket, with pocket depths order of magnitude larger than gap thickness. In this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of ltaipu power plant. Bearing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket.

Jul 31, 2018

By Jan Lampke

Increasingly pelletizing discs are used for the recycling of dust and sludge. The applied pellet feed is highly variable, for example in terms of chemical composition, grain size distribution and raw density. These raw materials related factors lead to a destabilized pelletizing process, which initially must be homogenized through special mixtures, as well as the use of binders or additives. There are many possibilities to reach stringent restriction of material related target factors. On the one hand it is helpful to be flexible by changing the process parameters of the pelletizing disc. On the other hand, it is necessary to use a material-binder-formulation, which leads to a highly stable pelletizing process. The paper deals with an example of the use of agglomerating device, pelletizing disc, to prepare different dusts and sludges for material recycling. These dusts und sludges are mostly generated in metallurgical processes, e.g. sinterplant, blast furnace and steelworks.

Aug 16, 2017

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Flavia de Paula Vitoretti

Pelletizing of iron ore fines is an important process used to produce high quality of raw materials for the subsequent reduction processes in the ironmaking industries. The process involves the production of green pellets and subsequent induration on a traveling grate furnace to promote inner partial melt and agglomeration which confer physical and metallurgical proprieties appropriated to the subsequent reduction processes. The pellets are produced with addition of charcoal to improve efficiency in the reduction processes. The lignin coal from sugarcane straw is an alternative source to replace the charcoal or coke in the self reduction of pellets. This work focused on the influence of biomass on the chemical kinetics parameters inner agglomerate pellet structure under industrial process conditions of the travelling grate furnace due hot gas flows within the pellets.

Aug 1, 2018

By Kengo Usui

The energy consumption of Iron-making, especially Blast Furnace (BF), is very large. In order to maximize the utilization of limited resource, it is essential to reduce energy consumption and recovering waste energy in BF. This paper introduces energy saving equipment based on NSENGI’s over 80 BF construction experiences since 1963. The first is the technology for the Top Charging System for low fuel-rate operation. One of the important factors to achieve such operation, the burden should be charged uniformly. Since 1974, NSENGI have developed and delivered over 80 Top Charging equipments for such purpose and nowadays, developed new type Top Charging equipment with improvement of charging precision. The second is the technology for Solely BFG Operation in Hot Stove, which means no use of other fuel gas such as LDG, COG. It is realized by high combustibility of NSENGI’s Top-Combustion Hot Stove with Metallic Burners, and large amount of heat recovery of Waste gas Heat Recovery system with heat medium. The third is the technology for effective energy recovery in TRT. With NSENGI’s latest Gas Cleaning System “Multi-Vessel Electrostatic Precipitator" (MVEP), TRT will be able to generate higher electrical energy by approx. 30% than that of wet-type. In comparison with dry bag-type, MVEP allows temperature fluctuation which lead to generate higher electrical energy by approx. 10% NSENGI therefore, will be able to accept and meet your request widely.

Aug 1, 2018

By Aloizio Cesar Gonzaga, Leandro de Paula, Ismael de Souza Dias, Gladston Santos

Looking for greater competitiveness, Gerdau started in 2013 the operation of its hot strip mill in Ouro Branco, being a milestone in Gerdau's history, where it definitely entered the flat products business. This mill consists of the reheating furnace, primary scaler, a Duo-reversible Quadrupole Steckel mill, accelerated cooling and final coiling. The Steckel mill works with two backup rolls and two working rolls, the backup rolls being responsible for supporting the rolling forces and the working rolls for shaping and surface quality to the strips, having as main requirement quality of surface finish. These rolls suffer high wear due to the lamination process and are exchanged with high frequency to ensure the quality of the laminated strips, after the exchange are sent to the Work Roll Shop for grinding and are positioned Grinded work rolls for the next planned change. This movement is accomplished through the crane and an exchange device that attaches to the cylinders to be transported from the Rolling Mill to the Work Roll Shop. The target in this article is focused on an improvement in this Device to increase operational safety and reduce stoppage losses downtime at the mill, improving the cost / benefit ratio and increase production.

Oct 1, 2019

By Breno Totti Maia

In the present paper, a new energy balance equation was developed, considering the slag phase, in order to define the effects of jet penetration and determine a new value for the factor K. The factor K measure the resistance to momentum transference between exit nozzle and metallic bath. The experiments were performed based on the same conditions of the article used as a comparison. The results showed the same behavior between the experiments and it was possible to determine a new value for the factor K, which changed from the unit order for the metal phase system to hundredths order for the metal and slag phase systems. These results are considered unprecedented.

Aug 17, 2017

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Martin Chabicovsky, Milan Hnizdil

Emulsions are frequently used for the cooling and lubrication of working rolls during the cold rolling. The fact that the lubrication and cooling are not separable makes the optimization of both functionalities difficult. The higher emulsion temperature decreases the cooling efficiency compared to cold water. Heat transfer and fluid flow laboratory (Czech Republic), CRM (Belgium), Tata steel (Netherlands) and Henkel (Germany) cooperated on the increasing of a cooling efficiency during cold rolling. Part of this research was focused on an influence of the emulsion composition on a cooling intensity. The cooling efficiency was laboratory investigated. The stainless steel sample with thermocouple was heated and then it was cooled by a nozzle. Tests were performed with various emulsions and pure water. The heat transfer coefficient was computed from measured temperatures. The cooling intensity (heat transfer coefficient) of all tested emulsions was similar but an increase of the cooling intensity was found with water. Further various emulsions concentrations were tested. Results showed decreasing cooling intensity with increasing oil concentration. Adding additives therefore is thought to cause a noticeable decrease of the cooling intensity.

Oct 1, 2019

By Breno Totti Maia

Due to operational conditions and locations, BOF suffers variations in important parameters whose effects on the liquid bath are usually neglected. The present paper investigated two aspects: inner BOF pressure and oxygen temperature in the stagnant reservoir. The results have shown that oxygen temperature changes properties like density and velocity but has small influence on jet penetration. The BOF inner pressure has significant influence on jet penetration and creates a new challenge regarding nozzles dimensions considering overexpanding and underexpading jets.

Oct 30, 2017

By Shian Jia

Ultrasonic Stirring Technology (UST) is used in this study to manufacture Al-based nano-composites. Ultrasonic cavitation plays an important role in refining the microstructure, dispersing the nanoparticles and breaking up clusters of nanoparticles. In this paper, 6061/A356 alloys and Al2O3/SiC nanoparticles are used as the matrix alloys and the reinforcements, respectively. The nanoparticles were inserted into the molten alloy and dispersed by ultrasonic cavitation and acoustic streaming. A previously developed multiphase Computational Fluid Dynamics (CFD) model was used to study the cavitation and the nanodispersion phenomena during ultrasonic processing of these alloys. A comparison between the mechanical properties of the as-cast 6061 and 356 alloys and nano-composites has been performed.

Aug 16, 2017

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them there is the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. Thermodynamic studies related to the formation of mineral species containing Fe, O and Zn elements were carried on due to the influence of these compounds in hydrometallurgical EAFD recycling processes. In recent years, a rise in the chlorine content of this residue was observed, mainly motivated by the increased use of scrap with polymeric impurities containing this element. In this work, based on computational thermodynamics tool FactSage, a general overview of gaseous and minerals species (found in EAFD) formed by Fe, Zn, O, Cl, H and C is shown – representing the organic origin of chlorine. For this study, the PVC polymer was used as the chlorine carrier substance which contaminates the EAF load.

Jul 30, 2018

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By Felipe Fardin Grillo

The aim of this work was to study the use of slags to desulfurization of cast iron. It was proposed to use alumina instead fluorspar. In addition, marble waste was used instead lime. Simulations applying Thermo-Calc software were performed in order to obtain the theoretical phases thermodynamic data. Then, a comparison between theoretical data and experimental tests were performed. The cast iron was melting in induction furnace at 1550°C. Slags composed mainly for CaO and Al2O3 were used to cast iron desulphurization. It was observed that increasing liquid phase, the desulphurization reaction was favored. Besides, it was found that cast iron desulfurization occurs by top slag mechanism.

Aug 17, 2017

By Francisco de Paula Pinheiro

Estudo das fontes de variação do processo de vazamento contínuo de chapas de alumínio, através da aplicação de uma metodologia prática e rápida para solução de problema. Após identificação das variáveis críticas à qualidade, ações foram tomadas de modo a minimizar as perdas do processo, o que contribuiu para a redução nos custos de produção das chapas.

Aug 16, 2017

By Pablo Bruno Paiva Leão

The present work is based on the characterization of nonmetallic inclusions in Ti stabilized ultra-low carbon steel, produced in a large steel mill. Due to a large incidence of submersed valve clogging in a continuous casting, the study is important in order to know the characteristics of the inclusions which are causing the problem. Total of 24 heats were sampled in the tundish and manually analyzed with a scanning electron microscope. The results revealed that 98.65% of the 3183 inclusions analyzed were solid in steelmaking temperature and 66.54% were alumina. The solid inclusions of alumina have low wettability for the iron bath, showing a high tendency of agglomeration in the submersed valves, affecting the castability. It has been concluded from the results and literature that some alternative measures such as the application of the treatment with calcium, precautions to avoid steel re-oxidation and the total or partial replacement of the pre-deoxidized element; would reduce the obstruction problem.

Oct 30, 2017

By Benito Barbabela e Silva

O pelotamento é a mais complexa etapa de aglomeração de finos de minério de ferro. Sua resposta é naturalmente oscilante, sendo bastante influenciada pelas características físicas obtidas nos processos de beneficiamento mineral que a precedem e tem papel crucial para a etapa de tratamento térmico de sinterização à jusante. O presente trabalho aborda o processo de classificação de pelotas verdes, sólidos singulares de aspecto deformável e pegajoso, em peneiras de rolos por modelamento por aplicação de Método dos Elementos Discretos. Esta técnica mostra-se como uma importante ferramenta pois supera as limitações impostas na modelagem física (quantificação e identificação de fluxos por ausência de instrumentação em escala industrial, amostragem sem representatividade) ao reproduzir de forma verossímil as repostas do sistema para importantes variáveis de controle: comprimento de gap, umidade, dispersão de tamanhos e resistência das pelotas.

Oct 30, 2017