Search Documents

By Saul Garcia Hernandez

The research work objective is to study a new ladle shroud internal design to reduce the slag emulsification in the tundish during ladle transient periods. A 3D mathematical model of the tundish was created to solve the fundamental equations, a turbulence model, and a multiphase model. The results show that using a conventional ladle shroud, the fluid is delivered with an excessive amount of kinetic energy being dissipated inside the tundish bath, generating strong mixing flow patterns and entrapping a massive amount of slag. In the other hand, the proposed ladle shroud dissipates the kinetic energy before the fluid enters the tundish promoting less intense mixing patterns; thus, the amount of slag emulsification is reduced significantly. Consequently, if the internal design of the ladle shroud is able to dissipate the kinetic energy before the fluid enters the tundish, it shall be possible to reduce considerable the slag emulsification and the slag opening area.

Aug 17, 2017

By Lucas Coelho da Silva

Este trabalho tem a pretensão de problematizar a influência da corrosão, sobretudo nos trocadores de calor, e trazer a importância de um estudo prévio detalhado, ressaltando como o desempenho deste equipamento está relacionado ao material utilizado e como esse estudo pode nos abster de grandes dispêndios. Através de ensaios eletroquímicos vamos estudar o comportamento do aço Super Duplex UNS S32750 em diferentes meios corrosivos, com o intuito de avaliar se o nível de corrosão do material é adequado para as condições severas de operação impostas a um permutador de calor.

Aug 16, 2017

By Francesco Toschi

The Special Bar Quality family comprises a wide range of steel grades, mainly requested by the automotive, energy and engineering sectors, for applications where significant performances are required (eg. stresses, temperatures, working cycles, etc.). To meet these requirements it is necessary to reach a precise control of both the mechanical characteristics and metallurgy structures along the whole production chain. For semi-product with large dimensions, such as equivalent diameters around 300 mm, this is traditionally obtained through a manufacturing route which comprises the casting in ingots followed by reheating, forging and rolling. After 2010, new processes were investigated and technologies developed to replace the ingot route with a continuous casting followed by controlled high-reduction rolling. In these processes a seamless integration of CCM with rolling is implemented so to obtain the precise control of material flow, applied deformation and working temperatures. By using the proper combination of rolling diameter, speed and applied reduction, a very good control of the metallurgy structure across the whole section can be obtained, so to also remove the internal discontinuities ("voids") generated during the continuous casting. These processes, which can be defined "forging-like", are applicable to several grades also with large semi-product dimensions (300 mm and more). Besides, removing the ingot route means increased yield and productivity, which is very beneficial to the economical management of the plant. An example of this "forging-like" process is represented by the high-reduction blooming stand installed by Acciaierie Venete in the Padova-Camin mill. This article describes its main concepts as well as its technology and process features.

Oct 30, 2017

By Antonio Adel dos Santos, Carmos Antonio Gandra, Fabricio Mazola da Silva Paiva, Vicente Tadeu Lopes Buono

Abstract Usiminas Steel Plant in Ipatinga installed an accelerated cooling device named CLC (Continuous On-Line Control) in 2010, enabling it to supply steels produced by TMCP (Thermo Mechanical Control Process) technology. This technology complements the TMCR (Thermo Mechanical Control Rolling), with the inclusion of the accelerated cooling process after controlled rolling. There are various gains in terms of quality and productivity associated to the application of such technology. However, the flatness control for API steel becomes crucial because large thermal stresses may be generated due to thermal heterogeneity during the fast cooling when the austenite phase decomposes mostly into ferrite and bainite. In literature, there is lack of knowledge regarding a full understanding of the relation among cooling conditions and plate flatness. Therefore, this work has focused on the effect of the cooling strategy for API steels, aiming at optimizing flatness and keeping the mechanical properties within the specified ranges. The starting point was dilatometer simulation, where cooling conditions such as start cooling temperature, SCT, finish rolling temperature, FRT, and cooling rate, CR, were changed in order to evaluate their effect on microstructure. Those laboratory conditions supposed to give the best results were transposed to industrial scale, so as to produce experimental lots of plates with five different cooling strategies. It was shown the possibility to find a cooling profile that guarantees the balance between mechanical properties and flatness requirements. The influence of cooling strategy on flatness was explained by the varied heat transfer regimes occurring from hot steel surface to the ambient

Oct 1, 2019

By Steven Gillgrass

Gerdau Monroe has installed and commissioned the Tallman Supersonic Carbon Injection system (TSCi™) for use in their 135-ton Electric Arc Furnace (EAF) located in Monroe, MI. TSCi™ is an innovative injection system with the primary aim of improving injection carbon delivery to the steel bath by increasing efficiency. It is proven technology with installations at numerous steelmaking facilities all over the world. Results from installation and commissioning of TSCi™ at Gerdau Monroe will be reported as well as on-going trials and optimization efforts. Standard injection systems deliver carbonaceous material from a vessel to the EAF using air where it is injected through a lance pipe or oxy-fuel burner. Using this method, material delivery to the EAF is limited by the pressure and velocity of the transport air. Loss of efficiency can be observed by looking at the quality of the injection carbon stream during operation or by measuring loss on ignition of EAF slag or off-gas system dust. TSCi™ uses a patented design and proprietary technology to improve delivery of carbonaceous material to the EAF. Using this method, savings at Gerdau Monroe were realized by reducing the amount of carbon used in each heat while maintaining or improving upon existing foamy slag practice. As well, significant savings were achieved as a result of reduced FeO content in the slag and improved recovery of iron. Additional savings can be realized by using a smaller mesh material to take advantage of lower material cost and higher injected surface area. Other inherent benefits to improved injection carbon include lower energy and electrode consumption, reduced refractory wear and reduced maintenance cost.

Oct 30, 2017

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By Gilberto Álvares da Silva

New elements have been inserted in NiTi lately, resulting in ternary alloys with specific characteristics beyond Shape Memory Effect and Superelasticity. Among all others alloying elements, the Ag additions itself gives potential antibacterial activity to that smart material. So on, the elaboration procedures of ternary NiTiAg alloys was studied in order to obtain a melting procedure to ensure further studies on this alloy. Microstructural and thermal analyses were used to evaluate the VAR-remelting production of NiTiAg with 4.0% wt silver content. The microstructure is composed by a NiTi matrix, pure Ag precipitates, and, scarcely, TiC inclusions. Heat treatments at high temperature could not dilute those Ag particles, but could lead to the precipitation of new ones. The silver element reduces the temperature of the martensitic transformation, yielding a material with superelastic behavior, beyond induces the R-phase on cooling stage of this alloy.

Aug 8, 2018

By Guilherme Corrêa Soares

The effects of temperature and strain rate on the mechanical behavior of a superelastic NiTi wire were investigated by uniaxial tensile testing. A universal testing machine with an attached heating chamber was used for the tensile tests. Temperature influence was studied through straining of samples until rupture at a fixed strain rate and temperatures of 25, 50, 75, 100, 125, 150, 175 and 200 °C. Strain rate effects were investigated by straining samples until rupture at room temperature and strain rates of 10-2, 5 x10-3 , 10-3, 5 x 10-4 and 10-4 s-1. The effects of temperature and strain rate on NiTi mechanical behavior were discussed in terms of critical stress to induce martensite and austenite yield strength, when applicable; upper plateau stress, transformation plateau length and ultimate plateau stress. It was found that increasing test temperature and strain rate shifted the stress-strain curve upwards, albeit temperature displayed a greater influence. Plateau length increased with temperature, but no significant changes were detected as a result of different strain rates.

Aug 17, 2017

By Maycon Athayde

Samarco produces high quality iron ore pellets processed in straight grate furnaces. This process is essential in order to obtain adequate mechanical strength to the pellet transportation and operation in the reduction reactors. All mechanical properties of the agglomerates are obtained during the stage of firing where the slag and sintering bond happens, thus it is a decisive step to improve the pellet quality. Therefore, the velocity distribution of gas flow within this zone must have homogeneous and even velocity distribution. Hence, it was developed a mathematical CFD model to characterize the gas flow in the burning zone, applying the equations of conservation of momentum, mass and energy and an uneven flow distribution was identified and the gas velocity analyzed and validated through experimental data. On the other hand, on the present paper, an improved firing zone burner were developed and industrially implemented in a way to mitigate the uneven flow pattern detected aided by CFD. Different burner designs, based on CFD analysis, were experimented in order to succeed on the aggressive condition. The combustion was investigated and burner efficiency evaluated and compared with the simulation purposed.

Aug 2, 2018

By Xihuai Gong, Hongshuang Di, Jianping Li, Ning Yan

In this work, we investigated the effect of the rolling process (warm-rolled or cold-rolled) on microstructure evolution and mechanical properties of 9Mn steel. After intercritical annealing at 670°C for 10min, both cold-rolled and warm-rolled microstructures are composed of ultra-fined austenite and intercritical ferrite. The austenite in warm-rolled sample includes two types of morphology, namely equiaxed and lamellar, which exhibits a wide distribution of grain-size. The incomplete recrystallization or recovery behavior of ferrite in warm-rolled and annealed sample results in higher yield strength and shorter yield point elongation. Moreover, the warm-rolled and annealed sample extends the TRIP-related work hardening over a broad strain range, resulting in a better combination of ultimate tensile strength and total elongation.

Oct 1, 2019

By Jörg Thomasberger

Delivering liquid steel to a steel processing unit at right temperature is an important criterion for high production steel shops, but it is surprising how little attention has been paid in the past to manage this vital phase in the steelmaking process-the steel in transit. The ladle running costs, both directly and indirectly, contribute significantly to the cost of steelmaking and should be an area of concern to any high production steel plant. Here we are talking not only of refractory costs or preheating fuel costs, but also cost of extra heating in ladle furnace, additional process delays incurred in delivering steel at right temperature to downstream unit in case proper care is not exercised at upstream unit, and occasional costs of ladle breakout due to inability to judge the residual life of the ladle. This paper emphasizes the need of a comprehensive ladle management system, an aspect which has not been properly addressed in the operations of a steel plant, in improving the productivity of a steel melt shop. Starting with review of present status and the attempts at implementation of ladle tracking in steel melt shop automation system, it looks at components of an exhaustive Ladle Management System (LMS), and finally gives an idea of benefits that will accrue from implementation of such a system in a steel melt shop.

Aug 17, 2017

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Fernando Velazquez Guzman

Titanium is an alloying element used to refine grain size in steel and improve its physical and mechanical properties. In some stainless steels it is used to increase the resistance to corrosion by the precipitation of titanium carbides or carbonitrides. Its alloying performance is highly variable and depends largely on the stage of the secondary metallurgy process when it is added. Furthermore, the addition method (wire injection or direct addition) has a remarkable influence in secondary refining. This paper describes the tests performed in vacuum degasser (VD), with a highly compacted and encapsulated Ferrotitanium wire (FeTi HC). The yield of titanium in steel increased from 52% to 89%. Moreover, the consumption of the highly compacted Ferrotitanium was optimized.

Oct 30, 2017

By Daniel Augusto Godinho de Carvalho

At thyssenkruppCSA, a positive heat balance at BOF process is faced, mainly because of low utilization of scrap and plant design. A singular logistic concept for hot metal transport between blast furnace and steel plant was established to optimize transportation and energy balance. Up to 80 kg of iron ore pellets/t steel is necessary for 340t BOF heat balance. In order to accomplish this challenge a stable blowing process, intensive operational development have been successfully executed: slopping rate reduction of 80% achieved without changing the blowing time. This paper describes steps and results of this development.

Oct 30, 2017

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By João Alberto Fioresi Altoé

Nas indústrias petroquímicas, nucleares e farmacêuticas o avanço tecnológico tem como objetivo a segurança e confiabilidade dos equipamentos com relação à resistência mecânica e à corrosão. Atualmente, o uso dos aços inoxidáveis superausteniticos é uma solução interessante, para uma maior vida útil dos componentes industriais submetidos a ambientes agressivos, como em meios salinos. Esse trabalho tem como objetivo investigar o aparecimento de pites em um aço comercial superaustenitico de composição química aproximada 25Cr28Ni4Mo em solução salina de cloreto de sódio. O aço foi fundido e tratado termicamente por solubilização a 1050ºC por 1h com o objetivo de eliminar os precipitados. As análises microestruturais antes e após os ensaios de corrosão foram feitas por microscopia óptica e eletrônica de varredura. Observou-se com os ensaios eletroquímicos de Polarização linear e impedância, que o aço inoxidável superaustenítico apresenta excelente resistência à corrosão em meio salino, caracterizado também pelas imagens que não revelaram a formação de pites, mesmo quando submetidos a elevados potenciais.

Aug 16, 2017

By Diego Pinheiro Aun

Neste trabalho, foi investigada a influência da textura de fitas de NiTi superelástico no início do processo de cristalização de um revestimento de TiO2 flexível. Foram utilizadas a calorimetria diferencial, cartografia Raman e difração de raios X para o estudo. Foi mostrado que existe uma influência significativa da textura do substrato no crescimento de grãos de anatase e rutila no filme de TiO2. Amostras com menor rugosidade apresentaram grãos mais desenvolvidos para todas as temperaturas de cristalização. Mostrou-se também que o substrato de NiTi promoveu a formação de TiO2 rutila em temperaturas abaixo daquelas observadas para a cristalização de pós.

Aug 16, 2017

By Douglas Glenn Stalheim

Production of structural steel with a minimum yield strength of 700 Mpa produced as hot rolled coil has become increasingly popular due to cost considerations when compared to quench and temper equivalent product. This grade when produced as hot rolled coil requires the use of microalloy precipitation strengthening mechanisms. This is typically a combination of niobium and titanium microalloys. While the metallurgical concept of structural steel precipitation strengthening mechanisms has been well researched and published, actual implementation into the production process can be very challenging. In addition to achieving a minimum yield strength of 700 Mpa, in many applications additional mechanical property attributes of formability as measured by hole expansion testing along with low temperature toughness properties are now required. Achieving a balance of all the mechanical properties in a stable and repeatable performance in production using microalloy precipitation strengthening mechanisms further increases the challenges. This paper will discuss the metallurgical/process strategies required to successfully produce 700 Mpa minimum yield strength hot rolled structural steel coil. In addition, the role and goals of both niobium and titanium in this product design will be presented.

Oct 30, 2017

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018