Search Documents

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Xihuai Gong, Hongshuang Di, Jianping Li, Ning Yan

In this work, we investigated the effect of the rolling process (warm-rolled or cold-rolled) on microstructure evolution and mechanical properties of 9Mn steel. After intercritical annealing at 670°C for 10min, both cold-rolled and warm-rolled microstructures are composed of ultra-fined austenite and intercritical ferrite. The austenite in warm-rolled sample includes two types of morphology, namely equiaxed and lamellar, which exhibits a wide distribution of grain-size. The incomplete recrystallization or recovery behavior of ferrite in warm-rolled and annealed sample results in higher yield strength and shorter yield point elongation. Moreover, the warm-rolled and annealed sample extends the TRIP-related work hardening over a broad strain range, resulting in a better combination of ultimate tensile strength and total elongation.

Oct 1, 2019

By Rudá Grossi Coimbra Martins

A estruturação organizacional da gestão da informação em Central de Serviços já está consolidada no ambiente de Tecnologia da Informação. O ambiente de Tecnologia de Automação compartilha características semelhantes, já que também fornece serviços para seus clientes. Entretanto, serviços de automação possuem particularidades derivadas, em grande parte, do fato de que são mais críticos para a atividade fim da empresa, já que visam manter a operação. Implantar uma Central de Serviços em ambiente de Tecnologia de Automação de uma empresa já existente demanda uma série de modificações em termos de Tecnologias, Processos e Pessoas para trazer os retornos desejados em termos de gerenciamento, organização da rotina e disponibilidade dos ativos. Este trabalho apresenta alternativas para atuar sobre os três componentes supracitados durante a implantação de uma Central de Serviços, com foco em sua operação através de uma Gestão Compartilhada (Cosourcing). Experiências adquiridas em projetos de especificação e operação de Central de Serviços também são apresentadas para embasar a estruturação da gestão da informação em ambiente de Tecnologia da Automação de indústrias de Metais e Mineração.

Jul 30, 2018

By Wujian jun

In the process of wire rod production, the rolled wire products must be cooled from the red-hot state to the normal temperature state. How to cool the wire rod after rolling is one of the key links of product quality control in the whole wire rod production process. In this paper, combined with the closed-loop transformation project of controlled cooling temperature of Xuanhuan iron and steel group co., LTD., the closed-loop related controlled cooling equipment (including water cooler, valve table, etc.), nozzle layout and process layout of water tank, and closed-loop software control system of controlled cooling temperature of high-line are analyzed and designed. Closed-loop system design USES temperature of cooling water cooling and water cooling two temperature closed loop regulating circuit, through temperature feedback and feedforward to achieve the uniformity of temperature adjustment, in order to prevent occur due to temperature closed loop control function with the phenomenon of a steel before and after the temperature difference is bigger, system Settings have "absolute temperature regulation" and "relative temperature regulation" selection mode. The system has a self-learning mode, which can modify the temperature feed forward formula. In addition, this paper takes the hard wire 82B rod as the test object, and studies the process parameters and the comprehensive mechanical properties of the rod before and after the water cooling system reform. The research results show that the temperature closed loop system, can ensure the rolled piece temperature control precision of plus or minus 10℃, enhances the stability of wire rod cleaner performance. It can reduce water consumption by about 186m3/h and improve the utilization rate of cooling water.

Oct 1, 2019

By Johanna Alegría-Ortega

Cr/CrN bilayer coating was deposited on AISI 440C by Cathodic Arc. The composition and structure of the Cr/CrN coating were investigated by scanning Electron Microscope, X-Ray Diffraction and X-ray Photoelectron Spectroscopy. The results show that crystal structure obtained was CrN phase with preferred [220] orientation. The hardness and adhesion of coating also were studied. The evaluation of erosion-corrosion (EC) on 440C bare and coated with Cr/CrN was performed by carrying out wear tests using a slurry jet with impingement angle 90° at 4 and 8 m/s. Corrosion, erosion and synergism wear rate were evaluated following the procedure described in ASTM G-119-09. This study presents that the synergism wear rate exceeds 40% of the total mass loss for coating and 60% of mass loss for the 440C, being the most aggressive wear component. The increase in impact velocity generated a rise in mass loss for both 440C bare and coated. The Cr/CrN coating offers better corrosion and erosion–corrosion resistance under all the tested conditions.

Aug 8, 2018

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By Beatriz Pereda, Ana Clara Fonseca da Silva, Tiago Seixas Bittencourt

Reinforcing steel bars are usually specified based on mechanical properties with flexibility in chemical composition and processing. Most developments, in these steels, are normally focused on alloy and process design to reach minimum cost and conformity to specification. Processing routes using quenching and self-tempering (QST) and accelerated cooling are the most common. Microalloying with V and Nb have been used in rebar. When acicular constituents must be avoided, a combination of Nb microalloying with judicious control of cooling is one of the preferred options. Niobium can contribute to improvement in tensile properties through austenitic grain size control during hot working, precipitation hardening due to carbonitrides or clusters, and hardenability increase. In the present work the alloy design and development processes of a Nb microalloyed steel for rebars are presented. The designed steel has fulfilled the required specification and is under regular production. Austenitic grain size refining – when comparing with the “basic composition” normally used was observed, even without any change in the thermomechanical processing cycle. There are indications that precipitation hardening may also occur. Results indicate that Nb is a good alternative as a microalloying element in rebars.

Oct 1, 2019

By Vitor Guarnier Domiciano

A necessidade de melhorar as propriedades dos refratários monolíticos para resistir às condições operacionais cada vez mais severas e instáveis das casas de corrida de Alto-Forno tem sido um grande desafio para os fornecedores de refratários de maneira a garantir a segurança dos canais de corrida e sua disponibilidade para operação. Este trabalho apresenta as propriedades de novos concretos refratários Al2O3-SiC-C (aplicados por vibração ou bombeamento/projeção a úmido) desenvolvidos para resistir ao severo mecanismo de corrosão que ocorre na linha de gusa de canais principais e que exige constante atenção dos operadores das casas de corrida. Testes realizados com os novos concretos refratários em canais de corrida principais de diferentes Altos-Fornos de grande produtividade revelaram uma significativa diminuição da velocidade de desgaste do revestimento refratário na linha de gusa oferecendo uma condição operacional segura e confiável às casas de corrida.

Aug 16, 2017

By Maurilio Pereira Gomes

The aim of this work was to heat treat and characterize sintered valve seat inserts (VSI). The powder metallurgy route was the only way found to substitute cobalt and lead, used in the VSI original alloy, due to their high cost and toxicological effect, respectively. The studied VSI was obtained with AISI M2 high-speed steel powder mixed with iron powder and other additives such as manganese sulphide, graphite, zinc stearate, carbides and copper, which was added by metallic infiltration. All the VSI were air quenched and double tempered, for one hour each, at seven different equidistantly temperatures, ranging from 100 °C up to 700 °C. The physical and mechanical properties were evaluated by means of the VSI apparent density, apparent hardness and crush radial strength. The chemical composition was determined through gas analysis, for the light elements such as carbon and sulfur, and energy dispersive X-ray fluorescence spectrometry for other elements. Microstructural characterization was performed with the support of scanning electron microscopy and energy dispersive spectroscopy. Regarding the VSI final application, the best results were achieved with the inserts air quenched and double tempered at 600 °C.

Oct 30, 2017

By Marco Antonio Meggiolaro

Notches are preferential sites for fatigue and for environmentally assisted cracking (EAC) initiation. Semi-empirical notch sensitivity factors have been used for a long time to quantify notch effects on fatigue design. Recently, this concept has been mechanically modeled using techniques which properly consider the notch tip stress gradient influence on the fatigue behavior of mechanically short cracks. This model properly calculates such values from the basic fatigue resistances of the material, its fatigue limit and crack growth threshold, considering the characteristics of the notch geometry and of the loading, without the need for any adjustable parameter. Such criteria to estimate notch sensitivity and tolerable short cracks on fatigue have been extended to EAC conditions and verified by proper tests. In its simplest version, the criterion for the maximum tolerable stress under EAC conditions uses the resistances to crack initiation and to large crack propagation and the characteristic short crack size under EAC, considering the crack size and stress intensity factor. Moreover, the tolerance to short cracks under fatigue and under EAC conditions can be unified in an extended Kitagawa-Takahashi diagram, a new and potentially very useful tool for material selection tasks.

Aug 8, 2018

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Patrick Edward Connell

The next generation of the well-established 3-roll Reducing & Sizing Block (RSB), the RSB SCS® is the latest milestone in reducing and sizing technology for SBQ products. It offers enhanced bar quality, improved productivity, mill availability and economy as well as a simplified, safe and environmentally friendly operation. A newly developed modular drive concept of the RSB SCS® grants a smaller footprint in the layout, a reduced oil-lubrication volume and a simplified maintenance schedule. Intelligent engineering leads furthermore to reduced hydraulic functions of the RSB SCS®, which ensures a safe and environmentally friendly rolling. Another integral part of the RSB SCS® is an innovative stand changing concept, which allows automatic stand changing within three minutes. The new RSB SCS® also includes a Fast Remote Control (FRC) which enables the immediate adjustment of the roll gap against the rolling force (under load) within milliseconds. Size changes along the free-size range can also be made within the traditional billet gaps in less than five seconds. At the core of the future-oriented RSB SCS® is a real-time closed-loop control system called Size Control System (SCS®) acting with 3-roll stands adjustable under load (AUL) and / or the heavy duty stands. These features remarkably further improve the rolled tolerances and their reproducibility, and at the same time simplify the operation by means of an automated optimization of the process parameters for the rolled bars.

Aug 16, 2017

By Jorge Maldonado Villa

Se desarrollaron materiales compuestos de matriz polimérica para toberas en cohetes; con dos zonas: una térmica para soportar elevadas temperaturas de combustión y una estructural que resista los esfuerzos generados. La zona térmica se elaboró con materiales de comportamiento ablativo, probados a temperaturas de hasta 2950°C durante dos minutos, los cuales fueron reforzados con polvo cerámico y/o subproducto de la industria siderúrgica (cerámico 2). Con base en los resultados obtenidos del comportamiento de térmico y de conductividad térmica del material ablativo, se construyó la zona estructural en materiales compuestos fibroreforzados (vidrio y carbono) con matriz polimérica. Los moldes se diseñaron en SolidWorks y se fabricaron por prototipado en ABS rápido y se elaboraron machos disgregables en poliuretano. En la zona térmica se usó un procedimiento de vaciado con vibración con diferentes tipos de matrices (poliéster, vinilester, caucho silicona) y de laminación para la zona estructural. Se evaluó el desempeño mediante simulación de las condiciones reales de operación mediante llama de oxicorte y quemador de ACPM, observando el efecto en la pérdida de peso, espesor, diferencial de temperatura, cambio de propiedades mecánicas, etc.; encontrándose un positivo comportamiento del sistema con matriz de resina vinilester reforzado con polvo cerámico 1 y buenos resultados con cerámico 2, así como una estabilidad en la zona estructural construida con fibras de vidrio y carbono. Substituir todo o texto de orientação deste Template pelo conteúdo de seu trabalho. Inserir o texto com no máximo 1.500 caracteres (200 palavras), sem uso de parágrafos. Deve conter, de maneira concisa, o objetivo, a metodologia, os resultados e as conclusões do trabalho.

Aug 17, 2017

By Homero Delboni Junior, Thiago Nunan, Flávia Vargas

Ball mill liners perform two main functions in grinding process: protect the mill shell from the aggressive milling environment and delivery input power to the charge. When it comes to liners optimization the challenge are to prolong the service life and improve grinding performance. Some liners characteristics such as A / B ratio, lifters number, lifter height, and attack angle are extremely relevant to grinding process. By analyzing process data, and through DEM simulations application, these parameters were improved on W-mill liner, located at Vazante concentration plant. The new profile promoted a reduction of power variability between the final and the initial life cicle intervals and, therefore, better stability to circuit operation. In addition, the new liner service life reached 21,603 hours, 25% higher compared to the previous one in use. This optimized profile therefore proved to be able to improve its functions by achieving superior process performance combined with longer service life.

Oct 3, 2019

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019

By Kenneth Holmnerg

About 100 million terajoule is used annually worldwide to overcome friction and that is one fifth of all energy produced. The largest quantities of energy are used by industry (29%) and in transportation (27%). Based on our recent studies on energy use in passenger cars, trucks and buses, we concluded that it is possible to save as much as 17.5% of the energy use in road transports in the short term (5-9 years) by effective implementation of new tribological solutions. This equals to annual energy savings of 11.6 exajoules, fuel savings of 330 billion liters and reduction in CO2 emission by 860 million tonnes. In a paper mill, 15-25% of the energy used is spent to overcome friction. The electrical energy used by a paper machine is distributed as 32% to overcome friction, 36% for the paper production and mass transportation, and 32% is other losses. In paper machines, 11% of the total energy used to overcome friction can be saved by the implementation of new tribological technologies. This would result in electrical energy savings worldwide of 130,000 terajoule, economic cost savings of 2 billion euros and CO2 emission reduction of 11 million tonnes annually. An overview of the total energy saving potential by improved tribology in transportation and industry is presented.

Jul 31, 2018

By Gilmar Ferreira Bataglia

The possibility of parameterization of hot tensile data together with creep data is investigated, for Aluminium Alloy 7475-T7351. This study represents part of a broader research program aiming at the validation of a methodology recently proposed for analyzing both kinds of data together, considering different metallic materials. The results presented in Part 1 of this work, were analyzed according to 4 traditional methods of the literature for parameterization of creep data, namely: Larson-Miller, Orr-Sherby-Dorn, Manson-Succop and Manson-Hafferd. The compatibility of the hot tensile test results with those of creep is remarkably good, indicating the possibility of using both kind of data together also in extrapolation schemes. The criterion proposed for equivalence between hot tensile and creep data is verified to work well also for this kind of material, under the present experimental conditions.

Aug 8, 2018

By Ronaldo Santos Sampaio

This paper call attention to increasing ratio of oxygen depletion from atmosphere besides the global worries about CO2 concentration increase in the atmosphere. It highlights the big mistake in considering Carbon Capture and Storage, CCS, as a way to reduce the increasing concentration of CO2 in the atmosphere. As a hypothetical example it presents an existing pseudo-ecosystem of manufacturing that has real windows of opportunity to increase its share in the global materials production industry, even in highly industrialized countries. As a suggestion and example the author point out possibilities to almost fulfill the proposed simple rules to be considered inside an ecosystem of manufacturing utilizing the production of steel via biomass versus fossil coal. A relevant and difficult rule to be attained in a quasi-ecosystem of manufacture is to be a near zero atmosphere oxygen depletion integrated process. The industrial alternatives that utilizes the actual photosynthesis are the ones that can reach a higher ecosystem of manufacture’s index. It is presented an ideal integrated steelmaking process where the gaseous, liquids and solid residues generated in one part of the system are or can be utilized in the other parts of the same system. A potential ecosystem of manufacture to produce primary iron is illustrated in the paper.

Aug 17, 2017

By Thierno FALL

This paper describes the study of the work-roll during the hot rolling process thanks to a 3D model built with the Finite Element Method (FEM). In terms of computational cost, that method needs high resources compared to 1D model which are mostly used. However, the 3D model is built to have a better understanding of the work-roll thermal and mechanical behavior during the hot rolling process. The thermal model shows that the highest temperature reached during rolling are within the range of 500°C and 600°C. The thermal field input used to simulate the mechanical behavior of the work-roll shows a biaxial thermal stress state, in the circumferential and axial planes. However, a peak of radial stress is observed in the backup zone. It did not generate plastic strain but could influence the fatigue behavior of the work-roll.

Oct 1, 2019