Search Documents

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Aitor Elorriaga Fernandez de Arroyabe

The purpose of Sinter plants is to heat iron ore fines along with fluxes and coke fines or coal, to produce a semi-molten mass that solidifies into porous pieces of sinter with the needed size and strength. Fluxes used in the sintering process need to have an appropriate size distribution and TI to avoid generation of fines, which could reduce the productivity of the Sinter. Besides, a homogeneous chemical composition and high absorption characteristics are necessary to control the basicity and to combine the flux with P, S, Si, etc, respectively. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification, being olivine and serpentine its principal minerals. It is a very homogeneous and hard stone and its main characteristics are: high hot and cold resistance to mechanical stresses, softening and melting points of a flux not of a refractory material. In addition, due to its mechanical and chemical properties, less fines are generated in the sintering process and during the handling and transportation to the blast furnace, improving the productivity of these processes. In this way, the use of PASEK Dunite allows increasing the homogeneity structure of sinter, reducing the percentage of return fines and improving the Sinter productivity.

Oct 30, 2017

By Pietro Palma

Universal cardan joints are widely used in drivetrains of rolling mills for steel and aluminum making, as well as for non ferrous alloy industry. Working conditions are extremely tough due to high alternating or pulsating rolling torques in the roughing stands and high torques and speeds in the finishing stands. Overloads and lubrication along with oxide and slag are also critical issues that contribute to create severe working conditions. For a constant and reliable power transmission rolling mills performance and uptime rely on Universal cardan Joints which are the most critical equipment of the drivetrain. Fatigue assessment of the most important components of the Universal cardan Joint is therefore definitely vital for the mill in order to avoid failures and consequently downtimes. Considering the component’s dimensions and weight and in addition the time needed in order to reproduce full scale tests, a new approach to study the Universal cardan joint’s main components fatigue behavior has been investigated. It consists in reproducing the local stress condition of the main joint components on small scale specimens that can be tested by conventional laboratory fatigue machines. The aim of this study is to analyze the most critical stress concentration areas in the universal cardan joints highlighting how a universal cardan joint Wöhler curve can be determined through laboratory tests of small scale specimens.

Aug 16, 2017

By Andreas Jungbauer

The Chinese steel producer Rizhao Steel is now focusing on the highly attractive local and export markets for high-quality, thin-gauge strip products. The first line of five Arvedi ESP plants began operations in the spring of 2015. The new casting-rolling complex is designed for a total annual production capacity of 11 million tons of highquality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The energy consumption and related costs are reduced by up to 45% compared with conventional casting and rolling processes. This also means a major reduction in CO2 emissions. During the project phase, the plant personnel from China received extensive training at the licensor’s plant – Acciaieria Arvedi S.p.A. in Italy – to prepare them to deliver the best operational performance with the new state-of-the-art endless casting-rolling facility. The plant setup, the training and support program, as well as the latest results from the start-up are presented in this paper.

Aug 16, 2017

By Eduardo Reis de Oliveira

O alumínio por suas excelentes características físico químicas é empregado na indústria civil, automotiva, naval e aeroespacial. As características mecânicas dos sistemas solidificados dependem do arranjo microestrutural, mais especificamente do tamanho de grão, espaçamentos celulares ou dendríticos, das heterogeneidades de composição química, do tamanho, forma, distribuição das inclusões e das porosidades. A fusão de metais e, consequentemente, a solidificação, são etapas importantes na obtenção dos metais. Neste estudo iremos investigar a solidificação vertical ascendente em regime transiente do sistema Al-Mg. Está análise investigou experimentalmente o efeito das composições e dos superaquecimentos nas microestruturas solidificadas. Durante a fabricação dos lingotes, foram mapeadas a solidificação de cada liga. As microestruturas obtidas evidenciaram um aspecto essencialmente dendrítico, verificados através da microscopia óptica. É estabelecido no trabalho uma comparação entre os espaçamentos dendríticos primário (EDP ou ?1) e secundário (EDS ou ?2) em relação adição de 1, 3 e 5% de Mg e com patamares de superaquecimento (?TV) variando em 20, 40 e 60ºC.A variação do superaquecimento e da composição química dos lingotes teve influência nos espaçamentos dendríticos, verificados nas medições transversais e longitudinais dos lingotes. Para cada posição analisada foram obtidas uma média dos valores e o respectivo intervalo de dispersão.

Oct 30, 2017

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By Douglas Glenn Stalheim

Production of structural steel with a minimum yield strength of 700 Mpa produced as hot rolled coil has become increasingly popular due to cost considerations when compared to quench and temper equivalent product. This grade when produced as hot rolled coil requires the use of microalloy precipitation strengthening mechanisms. This is typically a combination of niobium and titanium microalloys. While the metallurgical concept of structural steel precipitation strengthening mechanisms has been well researched and published, actual implementation into the production process can be very challenging. In addition to achieving a minimum yield strength of 700 Mpa, in many applications additional mechanical property attributes of formability as measured by hole expansion testing along with low temperature toughness properties are now required. Achieving a balance of all the mechanical properties in a stable and repeatable performance in production using microalloy precipitation strengthening mechanisms further increases the challenges. This paper will discuss the metallurgical/process strategies required to successfully produce 700 Mpa minimum yield strength hot rolled structural steel coil. In addition, the role and goals of both niobium and titanium in this product design will be presented.

Oct 30, 2017

By Claude Bodeving

The present steel economy drastically increases the financial strain on blast furnace operators. As a consequence, the importance of reliable cast floor operations is increasing drastically, which has a direct influence on the required clay mass and tapping equipment performances. When using modern high performance clay masses, pneumatic taphole drilling machines quickly reach their performance limits, which has made fully hydraulic drill hammers a standard in modern cast house operation. Besides the well-established hydraulic TMT hammers with high impact energy, an alternative version with lower impact energy, but high impact frequency was developed by TMT in the past, in order to achieve improved taphole protection. TMT’s recent research has shown that the drilling requirements inflicted by the taphole condition change over the taphole length, which has triggered the development of a new hammer, capable of switching between a high impact frequency mode and a high impact energy mode.

Aug 17, 2017

By Klaus Pronold

Once installed rolling mills can look forward to a long life. Around 40% of the 140 conventional hot strip mills presently in operation were built between 1960 and 1970. 17 of the 29 CSP®-plants were commissioned before the year 2000 and have automation platforms that are obsolete and/or have outdated rolling technology. Keeping pace with the market requirements is an ongoing challenge for producers of flat steel. It is a real balancing act keeping production facilities performing at necessary levels, safeguarding the investment and keeping outage periods to a minimum. To overcome these demanding factors and strike the right balance allowing for the production of higher grade steel that meets the current market price the installation of mechanical equipment as well as automation platforms and process technology must meet the latest technology standards. Being discussed in this paper are the different motives for modernizations along with their impact on project handling and commissioning philosophies. Experience gained during recent modernization projects in the field of flat steel rolling relating to Steckel / plate mills or current CSP® modernizations will be shared and demonstrate that each modernization has its own individual solution. Specific strategies are explained to help optimize production, increase plant agility and maximize the return on investment.

Aug 17, 2017

By Karl Berger

Today we are talking about Industry 4.0, as the latest revolution of industrial processes and progress, considering that the steam engine (Industry 1.0), railways and cars, mass production in the 1920th (2.0), Industrial Automation (3.0), and finally integrated manufacturing, integrated communication, and internet (4.0) can be seen as the state-of-the-art situation in industry, nowadays. Similar to the Industry progress, we can approach the rolling process of material, which started about 150 years ago in a very basic way. Steam engine- and belt driven-mills were very operators’ intensive, brutal and risky to operate. Mechanical improvements brought throughput, safety and quantity, as also quality of the products. The rolling of steel, in particular of rails, beams, rebar, strip (focus in this paper) and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. From single stands to continuous rolling trains the production and quality of mills increased significantly. From ingots and blooms to slabs, we have to admit a big jump in which has changed the face of the world significantly. Thin Slab Rolling has revolutionized the output and the throughput of rolling mills (Generation 3.0 to 5.0). Finally, Endless Rolling, has boosted the quality and quantity of rolling mill processes and permitted nowadays to enter in market niches which were not thinkable a decade ago. Mastering the automation and applying reliable systems (mechanical and electronically) of drives, actuators and sensors, as also communication and information interchange to all levels of automation are the success factors of such complex mills, we call herein after “Rolling Mills of Generation 6.0”.

Aug 16, 2017

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019

By Rogério Martins Pereira, Charles Pierri de Souza, Lucas Gabriel Correa

The Tandem Cold Mill is composed by stands with rolls positioned so that the rolling force can be transmitted to the strip being processed. Due to the mechanical stresses inherent in the process, the roll bearings are heated and are equipped with lubrication and cooling systems. Nevertheless, there is the challenge of continuously monitoring the temperature of the bearings, which would allow preventive intervention in case of overheating. This paper presents an in-house solution to temperature measuring system applied to the backup roll bearings of a continuous Tandem Cold Mill. The system uses Zigbee technology and is integrated with the main control system, allowing early diagnosis of bearing heating and proper intervention. Results and features of the system are discussed.

Oct 1, 2019

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Ivo Filipovic

The steel melting process in an Electric Arc Furnace is a complex set of tasks, coping with highly dangerous hazards as fire, explosions, uncontrolled reactions, hot metal projections and gas or dust emissions. Melt shops are dangerous working areas for operators, recording statistics with a high frequency of injuries. In the past years, without dedicated safety equipment, there wasn't a real attitude to the risk prevention. The paper describes the available technological packages to eliminate the manned activities on the melting floor, with the aim to prevent accidents and keep furnace operators safe. The technological packages suite extends the automatic control of the EAF melting process to all the operations from charging phase to tapping. Plus, the integration of the most frequent operations by automated specialized tools effectively minimizes power-off times, enhancing reliability and improving the transformation costs.

Aug 17, 2017

By Stefano Scubla

DANIELI Q-MELT is the latest evolution of EAF concept to automatically control each stage of the melting process, from the electric power planning to the combustion optimization as well as the slag and steel metallurgy management for every operation required in the EAF cycle. The core of the automation system is the Melt-Model that automatically identifies deviations of the process control variables and corrects them to avoid losses or wasting of available energy sources. The real-time online off-gas analysis, via the in-situ laser system, promotes the process tracking and permits further optimization by a viable closed-loop control acting on fuel and oxygen postcombustion. A suite of supplementary stand-alone Technological Packages integrates the Q-MELT to further maximize the productive time and the utilization factor, supporting the operators to limit downtimes, avoiding misoperations and/or mistakes.

Aug 16, 2017

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017

By Roman Vaynshteyn

In places where Blast Furnaces are usually located, climatic factors may be unfavorable. Raw materials may be exposed to e.g. rain during transport/storage, bringing moisture into the process with consequences for stability and hot metal cost. This paper describes a technology for drying and pre-heating pellets and coke in the stockhouse. It does not require additional handling or logistical equipment and does not introduce extra transfer steps and degradation. Not only can moisture content be reduced, it can be controlled to a stable level by the operator.

Aug 16, 2017

By Eddy Dierckx

Modernization of flat rolling plants is essential to sustainably fulfill increasing market demands and to improve competitiveness. Intelligent modernizations ensure getting maximum prime yield of existing mills, even if they have gone through half a century of operation. Existing mills were designed based on former production, consumption and quality targets. Ever increasing requirements such as increase of productivity, change of product mix (e.g. new steel grades), reduction of energy consumption and improvement of product quality lead to the necessity to adapt the existing equipment to the new target. SMS group provides, besides the reliable equipment and automation solutions to successful upgrades of existing mills, also a systematic approach to develop technical and economical solutions together with our customers (conceptual engineering). This paper describes the SMS group approach to modernizations / upgrades, introduces powerful performance modules and provides a number of successful examples that have been implemented recently.

Aug 17, 2017

By Nelson SOUTO, Nicolas LEGRAND, Christian COUNHAYE, Don EARLEY

The work is motivated by the automotive customer requirements for a roughness with high peak density (RPc > 75 peaks/cm) on steel sheet surfaces to maintain a good strip surface finish after painting. For that purpose, a new approach is utilized to compute roughness transfer and predict final roughness on uncoated steel sheets (average roughness, skewness, peak density) as a function of temper rolling conditions. The approach is based on the Monte Carlo method combined with the Abott curves and an auto-correlation function to numerically generate roughness profiles for roll and strip respectively. To compute the roughness transfer due to the interaction between roll and strip surfaces during rolling, a composite Abott curve that combines roll and strip Abott curves is used with an asperity crushing model integrated with a rolling model. This enables simulating two roughness transfer mechanisms in the roll bite: the strip asperity crushing mechanism by roll roughness and the strip asperity ploughing mechanism due to roll-strip interfacial sliding speed. The model shows the importance of considering the two mechanisms to predict roughness transfer correctly when strip elongation is high, typically a few percent, and roll bite friction is low. In these conditions, the forward slip at the exit of the roll bite tends to erode strip roughness significantly and decrease considerably the peak density on the strip. For lower elongation levels (~1%) and high roll bite friction, the ploughing mechanism becomes negligible and roughness transfer is controlled by the crushing mechanism only. With these two mechanisms, the model reasonably predicts the evolution of average roughness and peak density over a wide range of temper rolling conditions (new/worn work rolls, hard/soft grades, various elongations), but skewness is more difficult to predict for some trials.

Oct 1, 2019