Search Documents

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Jim Belous

Fluid Dynamic Modeling (FDM) was used to develop solutions how to eliminate the fugitive emissions from the meltshop building and to comply with the EPA “6% opacity from the furnace operations” rule. Secondary Emission Control (SEC) system performance was simulated by an inverted 1:96 scale Plexiglas model of the entire meltshop, utilizing the negative buoyancy effects of saline solution in water. Test results show that with the installation of the internal partition wall which separates furnace aisle from the caster aisle, significant improvement of the SEC system is achievable, thereby avoiding large expenditure for the expanding a fume collection system capacity.

Aug 17, 2017

By Mariano de Córdova

A operação dos altos-fornos com injeção de carvão pulverizado ou gás natural requer uma alta qualidade do coque. Para um custo mínimo do coque, mantendo a qualidade necessária, a escolha de carvões e a formulação da mistura é um tema muito importante. Uma ferramenta amplamente utilizada para o design de misturas é a modelagem, precedido pela caracterização de carvões e seguido de teste no forno piloto. Neste trabalho, revisa-se o desenvolvimento dos modelos, com base la literatura pública. Três etapas cronológicas são levadas em conta, desde os anos sessenta até a atualidade.

Aug 17, 2017

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017

By Gilmar Zacca Batista

The present work is a part of a comprehensive program that aims to evaluate the girth welding procedures for heavy wall API 5L X65 pipes produced for sour service applications. This article describes the results of toughness, strength and sour resistance of girth welds produced with different welding consumables. The methodology applied included girth welds production with GTAW process for root pass using ER70S-6 consumable and FCAW process for filling passes using E71T- 1CJ and E91T1-GM-H4 consumables. Mechanical tests of Charpy, CTOD, tensile, hardness and stress corrosion cracking were also performed. The E71T-1CJ resulted in a girth weld with tensile and yield strength around 7% lower than the pipe. However, according to the papers analyzed at this study, a value up to 10% of undermatching could be acceptable. The CTOD and Charpy tests showed good toughness and weld metal embrittlement was not observed. The hardness and the stress corrosion cracking tests demonstrated that the consumable ER70S-6 is suitable for sour service. All properties evaluated met the requirements specified by the onshore pipeline standards, showing that the consumables ER70S-6, E71T-1CJ and E91T1-GM-H4 are suitable for the welding of heavy wall X65 pipe with sour service and toughness requirements. If an overmatching is required, the E91T1-GMH4 shall be used to assure a strength overmatching and prevent plastic strain concentration at the weld metal. The results provided by this paper can be used for consumable selection and for welding procedure qualification of pipelines construction when heavy wall API 5L X65 are used for sour gas transportation.

Aug 16, 2017

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By Vinícius da Silva Madruga

Os processos de lingotamento contínuo e de lingotamento convencional apresentam diferenças na solidificação dos aços, esse fato tem impacto na distribuição, quantidade e forma de inclusões de óxidos e sulfetos. O objetivo desse trabalho é verificar de que maneira tais diferenças influenciam na distribuição dos sulfetos ao longo do aço solidificado de qualidade SAE 1050. Para isso, 20 amostras foram retiradas de eixos forjados e barras laminadas, produtos conformados de origem do lingotamento convencional e do lingotamento contínuo, respectivamente. As amostras foram analisadas em microscópio ótico e microscópio eletrônico de varredura no modo de análise automatizada de partículas. Através das imagens e de dados numéricos obtidos, foi visto que nas amostras de barra laminada há grande quantidade de sulfetos, se analisada na seção longitudinal, em relação às amostras de eixo forjado. Analisando na seção transversal, foram detectados menos sulfetos devido ao alinhamento dos mesmos. Entre as amostras de eixo forjado, a área ocupada pelos sulfetos é maior no pé do lingote, reduzindo em direção à cabeça, apesar de a cabeça apresentar mais sulfetos. Tais diferenças foram atribuídas à taxa de resfriamento, à seção transversal do produto e ao processo, que variam entre os dois tipos de lingotamento.

Oct 30, 2017

By DIEGO RAFAEL MONTEIRO DINIZ

Os processos de recebimento, armazenamento e distribuição de combustíveis em grandes empresas mineradoras necessitam de um controle robusto e eficaz de todas as operações, uma vez que representam elevado custo por tonelada de minério produzida e expedida. Para tanto, a automatização dos processos que envolvem combustíveis é necessária, capaz de promover redução de custos, aumento de produtividade, confiabilidade e precisão nos dados e melhorias nas condições de trabalho na gestão e operação em combustíveis. Foi aplicada uma análise descritiva de um estudo de caso de um projeto de automação para esta finalidade implantado na empresa VALE S/A. Foi feita uma avaliação sistemática dos recursos, equipamentos e tecnologias necessárias a completa automação e integração dos processos que envolvem combustíveis e os ganhos alcançados após a implantação.

Oct 30, 2017

By Zhisong Chai, Wei Xu

Q&P steels undergo continuous multiple processes, including hot rolling, intermediate heat treatment, cold rolling and continuous annealing etc. The inheritant effect of initial microstructure could affect the final microstructure and mechanical properties of Q&P steels. In this work, effects of different hot rolled microstructure/texture on the final microstructure and properties subjected to Q&P process were investigated in Fe-0.38C-1.58Mn-1.6Si system. Different initial microstructures were generated combing different TMCP and cooling strategies. The microstructure and texture of hot rolled materials were characterized in detail. The hot rolled material was subsequently processed by intermediate annealing, cold rolling and continuous annealing. The comparison reveals great effects of the initial hot rolled microstructures, i.e. inheritance effect. The faster reverse transformation would lead to more sufficient austenitization and it would greatly weaken the inheritant effect of the initial microstructure. Although the difference of final phase fraction for different initial microstructures was not significant, the inheritance effect was mainly reflected in the effect on austenite morphology. For the mechanical properties, no obvious difference in strength was shown for the samples with different initial microstructures after Q&P heat treatment, but there was fluctuation in elongation.

Oct 1, 2019

By Clebson Joel Mendes de Oliveira

Sulfur control in steel have been challenging process experts since the discovering of it deleterious effect on most of steel product properties. To separate this slag from hot metal is mandatory to complete desulfurization process. The preferred method is to skim hot metal surface physically removing the contaminated slag, attributing to the operator the evaluation of skimming efficiency. Thus, we present a new lower cost system using image processing methods foreseeing a future full automation skimming process.

Aug 16, 2017

By Glaydson Simões dos Reisr

Micropore organosilicas (MOs) were synthesized using methyl-phenyl-polysiloxane as precursor. The MOs were characterized using several analytical and functional techniques. The materials were assigned as micropores materials, with specific surface area up to 642 m2 g-1 and yield up to 72.55%. The adsorbents have hydrophobic surfaces and were used for removal of diclofenac from aqueous solutions. The adsorption kinetic and isothermal data were well described by the general order and Sips models, respectively. Diclofenac exhibited a better affinity than NM and the mechanism of adsorption suggested that hydrophobic groups play a key role in the adsorption process.

Aug 17, 2017

By Jean-Paul Simoes

The development of the blast furnace over the last years lead to a substantial increase in production capacity and productivity. This development triggered an evolution of the cooling systems in order to cope with the raising heat loads. The excellent protection of the shell by copper staves allowed blast furnace operators to achieve campaign lifetimes of more than 20 years. However in recent years some blast furnaces have experienced severe wear of the copper staves due to abrasion. The influences of the blast furnace design as well as of the operation conditions on this premature wear have been analysed and the mechanisms leading to the wear will be explained. New developments in the copper stave technology are part of the solution for avoiding premature wear during periods with less favourable conditions. The protection mechanisms made available by the new design extend the inherent protection mechanisms of copper staves to these periods. BFXpert® system is the ideal tool for the monitoring of the process data, the process models and the recommendations given by Sachem® support the operator in choosing efficient operation points. The charging with a Bell Less Top® (BLT) allows an accurate controlling of the blast furnace with regard to the optimization of the gas distribution. High performance operation together with long campaign lifetimes are thus made possible.

Aug 1, 2018

By Nicolás Lugo

The electric steel industry has reached a level of maturity in its relative participation in the world’s steel production. As the industry has grown and matured, EAF steel producers have participated in an ever more competitive market. This competition has led to a continuous search for lower cost alternatives for energy and input materials. Over the years, the Electric Steel Furnace community of operators has developed a variety of technological improvements geared to increasing EAF productivity. Operators have emphasized lowering operating costs and improving the quality of steels produced. Depending on market conditions, the EAF operators may run with different goals and priorities. In times of low demand, the goal may be to operate with an emphasis on cost and the goal of maximizing cost effective use of resources. When the market demand is high the goal may be to maximize EAF throughput. The objective of this work is to list some of the EAF operating best practices observed by our team in the electric arc furnace operations around the world. EAF operators can consider and possibly implement these practices depending on the specifics of each EAF operating reality.

Jul 29, 2018

By Bruce V. Kiefer

A modernization project was undertaken by Kroman Celik Sanayii A.S. in order to improve their product quality, consistency and shape of the coil package, reduce maintenance and delays in rod mill, thereby increasing utilization and productivity. The project involved installation of a new Morgan Intelligent Pinch Roll and High Speed Laying Head, modifications to the existing controlled cooling conveyor, plus replacing the coil reforming station. The new pinch roll and laying head were to provide better control of the ring formation and consistency of the coil on the conveyor, while reducing delays on the conveyor. Changes to the controlled cooling conveyor included installation of new nozzle decks and Optimesh air distribution system along with re-arrangement of existing fans in order to improve both cooling rates and uniformity of cooling. This paper explains details and features of the newly-installed equipment technology. Resulting product and process improvements are presented, including increased tensile strength and uniformity, reduction in delays on the conveyor and reform tub, plus improvements in coil quality.

Oct 30, 2017

By Francois Mignard

With a limited global steel production growth, automotive application market shows interesting volumes and trends especially in emerging countries. The recent period has again enabled Siemens VAI to confirm a position amongst leading suppliers of new plants serving high-end steel production in particular for unexposed and exposed automotive material. With a series of recent plant references in operation and under construction, relevant answers to such sustained level of performances are highlighted along the downstream processes. Designed for a wide range of applications, Siemens VAI processing lines includes advanced technological and state-of–the art equipment, among them, Solid state laser welder, Pickling Tunnel tanks, Skin pass mill and Tension leveller, Side trimmer with dynamic width adjustment, and new generation of Automatic surface inspection systems. With a continuous aim of driving improvements, Siemens VAI has also developed Global Quality Monitoring solutions notably through advanced software which provide just-in-time warnings and assist steel makers in the daily operation of their lines. As lifecycle partner, Siemens VAI offers solutions and services in metallurgical expertise from metallurgical modelling, through physical simulation on rolling, annealing and galvanizing processes, and enables Siemens to accompany our customers along with their project definition till fulfilment of highest market requirements.

Jul 30, 2018

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Werner Klein

The utilization of production facilities in an optimum way, with reliable due date fulfillment, reducing raw material and energy consumption, are challenges iron and steel companies are facing in their business every day. By using an APS system such goals can be achieved to increase the competiveness of iron and steel producers. A sophisticated APS supports the overall planning process by applying complex rules based on product and order mix, its production routings with corresponding processing and transport times and resource availability. Specific technological as well as steel grade and energy related constraints are also considered to meet company specific KPIs. A core feature of APS solution is to react online on deviations to plan during the production process. Deviations such as nonconformance of intermediate material attached to an order, sudden production delays, unavailability of important production resources, makes it necessary to update the production plan. In general the task of APS is to support the preferred work-to-order concept, by assigning work-orders to available production facilities along the product specific process route and generate optimized material sequences for critical work centers.

Aug 17, 2017

By Breno Totti Maia

In the present paper, a new energy balance equation was developed, considering the slag phase, in order to define the effects of jet penetration and determine a new value for the factor K. The factor K measure the resistance to momentum transference between exit nozzle and metallic bath. The experiments were performed based on the same conditions of the article used as a comparison. The results showed the same behavior between the experiments and it was possible to determine a new value for the factor K, which changed from the unit order for the metal phase system to hundredths order for the metal and slag phase systems. These results are considered unprecedented.

Aug 17, 2017

By Christoph Aichinger

The optimization and improvement of a modern integral iron and steel works gets more and more difficult as each individual plant is already operated at its best efficiency and at the lowest operational expenditures. However very often the individual plants are considered as stand-alone units and there are losses and inconsistencies on interfaces and take over points, which could be avoided and by that improving the overall performance of the iron and steel works as a holistic unit. Primetals Technologies looked into this subject extensively in the recent years and is now ready to offer new tools and services in order to assist operators to find further potential for improvement in processes, which seem to be fully developed at first sight.

Aug 17, 2017