Search Documents

By Antonio Fabiano de Oliveira

The aim of the present research work is to study the influence of hard chrome covered skin pass cold rolling rolls using 2D/3D surface topography, i.e. roughness characterization. The common stochastic structure Shot Blast Texturing (SBT) does not meet all requirements related to the production line regards to the finished product. The Hard Chrome layer, applied on these SBT rolls, can improve the sheet surface quality and is of fundamental interest mainly for those steel mills that do not have another alternative to new surface structures such as those that may be provided by the EDT, LT, EBT, etc. methods. The function of the generated surfaces, obtained by these different methods is going to influence the tribological properties during the subsequent forming processes. On the other hand, they can increase the product final cost or require large investments to obtain such surfaces. The results here presented are in accordance with other recently published research work, showing that there is a relationship between these parameters, and that further detailed studies are needed.

Aug 17, 2017

By Jose M. Rodriguez-Ibabe, Beatriz Pereda, Beatriz Lopez, Felipe Bastos

The modeling of austenite evolution during the hot rolling of steels is covered in the literature for a wide range of chemical compositions, although mainly for carbon contents below 0.20%. In addition, most research on this topic is oriented for processes that are characteristic of flat products. Compared to those processes, the hot rolling of bars for structural applications presents considerable particularities concerning mainly deformation, rolling speed and rolling temperature profile. Those particularities result in considerable changes on process parameters that affect the austenite microstructure evolution, both in the softening and hardening mechanisms if microalloying elements such as Nb is present. The aim of this work was to develop a model to predict the evolution of austenite microstructure that is suitable for the hot rolling of structural reinforcing bars. Different torsion tests simulating industrial schedules particular from those type of processes were performed. The tests showed the need to investigate Nb strain-induced precipitation interaction with softening mechanisms that can occur during the deformation schedule. At the end, the new proposed kinetics and routines were introduced to a program, MicroSim-Bars®, that is able to model austenite evolution under structural bar hot rolling conditions.

Oct 1, 2019

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Charles de Abreu Martins

An experimental investigation was conducted using laboratory-processed, 0.12C–1.70Mn–0.2V steels with different Cr or Mo additions aiming to evaluate this influence on the microstructure and mechanical properties hot rolled steels. Steels were processed in a pilot rolling equipment, simulating a typical thermomechanical processing, with finishing rolling steps above Ar3, followed by accelerated cooling and 723 K (450 Celsius) coiling temperature. Microstructures and precipitates were analyzed using OM, SEM and TEM, while mechanical properties were evaluated by tensile and hole expansion tests. Since Cr and Mo increase hardenability of austenite, and as a consequence, the volume fraction of the acicular constituents increases with gradual additions of Cr or Mo. Moreover, Cr or Mo impacted V precipitation process, reducing average size of particles. At 0.50%Mo, V precipitation was inhibited. Effects of this microstructure evolution on the final mechanical properties were also analyzed, as well as a comparison between Cr and Mo effects, with Mo presenting more effective influence.

Jul 30, 2018

By Dimas Henrique Barros Andrade

No cenário atual de empobrecimento da qualidade das matérias-primas carregadas nos altos-fornos, torna-se fundamental compreender os fenômenos que afetam diretamente a estabilidade operacional desses reatores. Este trabalho avaliou uma relação entre queda de pressão e intensidade de irrigação com a intenção de associá-los aos fenômenos de retenção e refluxo que ocorrem na zona de gotejamento de um alto-forno a coque. Não foi possível obter claramente uma relação entre as instabilidades operacionais e a ocorrência de fenômenos de inundação, porque não há uma separação clara entre os dias com e sem as instabilidades operacionais. No entanto, ao longo de um intervalo definido no diagrama, é notável uma maior ocorrência de instabilidades. Analisando os parâmetros, o que tem maior influência na permeabilidade da zona de gotejamento é a distribuição do tamanho do coque, avaliada pelo cálculo do diâmetro harmônico.

Oct 30, 2017

By Francisco Morganti

Weight reduction is the main target of all carmakers, which results in a continuous development of new steel grades. Latest 3rdgeneration advanced high-strength steel grades (AHSS) are complex materials with special chemical compositions and multiphase microstructures. The pickling, annealing and galvanizing processes of these grades aresomewhatdifferent due to the changed chemical compositions and microstructures. Therefore, these innovative steel grades place new demands on the plant technology of pickling, annealing and galvanizing lines. The most significant challenges for the pickling process are sludge occurrence during pickling, varying pickling times, weld ability of the materials, changed visual appearance and required high surface qualities. The most important topic concerning annealing line is a precisely controlled and very flexible heating and cooling process in the furnace.One of the new requirements in galvanizing linesis the prevention of surface faults caused by bare spots, which can occur since these materials feature a higher content of alloying elements like silicon or manganese. Prevention is possible with the special pre-oxidation technologies.Due to the higher strength of the material also the mechanical equipment has to be designed differently in these lines. This paper describes the influences of the changed chemical composition and material characteristics of modern steel grades on the pickling, annealing and galvanizing process and gives an overview about the technical solutions.

Oct 30, 2017

By Stefano Scubla

DANIELI Q-MELT is the latest evolution of EAF concept to automatically control each stage of the melting process, from the electric power planning to the combustion optimization as well as the slag and steel metallurgy management for every operation required in the EAF cycle. The core of the automation system is the Melt-Model that automatically identifies deviations of the process control variables and corrects them to avoid losses or wasting of available energy sources. The real-time online off-gas analysis, via the in-situ laser system, promotes the process tracking and permits further optimization by a viable closed-loop control acting on fuel and oxygen postcombustion. A suite of supplementary stand-alone Technological Packages integrates the Q-MELT to further maximize the productive time and the utilization factor, supporting the operators to limit downtimes, avoiding misoperations and/or mistakes.

Aug 16, 2017

By João Paulo Calixto da Silva

Os modos de desgaste de um material podem sofrer transições decorrentes de alterações nas condições do tribossistema. Para o estudo e análise dos fenômenos associados às eventuais mudanças, a técnica de micro-abrasão do tipo esfera livre é reconhecidamente uma boa escolha. No presente trabalho, para o aço inoxidável austenítico AISI 316L, fez-se um estudo do comportamento da taxa de desgaste, bem como do mecanismo de desgaste em função da carga de ensaio, tipo de abrasivo (SiO2 ou SiC), dureza do material (modificada pela sua nitretação) e concentração de abrasivo. O desgaste por deslizamento predomina quando a lama abrasiva é constituída de SiO2, enquanto o rolamento passa a prevalecer com a troca do abrasivo para o SiC. Verificou-se que em nenhum dos dois casos ocorreu transição de mecanismos após variações nas condições de ensaio. Por outro lado, o coeficiente de desgaste do material aumenta com a carga de ensaio, substituição do SiO2 pelo SiC e tende a cair com a nitretação (aumento de dureza) do aço e com a concentração de abrasivo. O aumento simultâneo da carga de ensaio e da concentração de sílica na lama diminui significativamente a taxa de desgaste, encurtando o período de "running-in".

Aug 7, 2018

By Aline Lima da Silva

The present work is focused on the thermodynamic study of the methane or biogas mixtures conversion on Cu-ceria catalysts. Several experimental studies reported in literature have demonstrated the ability of these materials to operate as SOFC anodes for direct methane oxidation, with the evidence of enhanced tolerance towards sulfur poisoning and carbon deposition. More recently, experimental investigations have shown the feasibility of Cu-ceria anodes to directly operate with simulated biogas feeds at intermediate temperature (1023K). In this way, the effect of the ceria redox properties on the equilibrium composition is investigated, considering methane or biogas mixtures as the fuel. Conditions under which carbon deposition and sulfur poisoning can be prevented are determined. Our study combines results from the classical thermodynamics, obtained with the help of FactSage software, with the new Cu-S and Ni-S diagrams proposed in literature, which were calculated based on the Density Functional Theory (DFT). These diagrams are able to predict a region where sulfur interacts with the metal surface through chemisorption. A comparison between the performances of Ni-YSZ and Cu-CeO2 catalysts is established from a thermodynamic viewpoint. Theoretical results are in agreement with the experimental trends from literature.

Aug 8, 2018

By George Schipper, Peter Gelten, Pepijn Adriaen, Hugo Uijtdebroeks

Tata Steel IJmuiden Hot Strip Mill 2 (HSM2, 5.5 Mtonnes/yr) is currently being upgraded, resulting in an increased rolling force and motor power capacity. With the current conventional work roll spray cooling, a deterioration in work roll & strip surface quality performance is expected as a result of the increased mill capacities. In order to improve strip surface quality, HSM2 decided to do a full-scale production trial with High Turbulence Roll Cooling (HTRC) at stand FM2. HTRC is a novel way of roll cooling using a high turbulent flow regime. HTRC is positioned very close to the roll surface and gap exit, which is beneficial for the roll surface quality. It is operated at a high flow rate but at a low pressure. HTRC not only significantly improves the roll surface quality, in addition, it makes high pressure pumps, needed for the conventional spray cooling, redundant, leading to substantial savings on electricity costs and thus CO2 emissions. HTRC is in trial operation since 7 August 2018. Results show no operational issues, an excellent roll surface quality and an increased cooling efficiency. In summer 2020 stands FM1-FM2-FM3-FM4 of HSM2 will be equipped with HTRC.

Oct 1, 2019

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Dennis Travagini Cremonese

In the early stage of front end studies of an Iron Ore Project, the sizing of surge capacities and stockpiles are normally assumed based on the experience of the study team. Understanding and sizing of these capacities at the early stages of the project are important for future stages of the project as drastic changes in sizes will impact the economics of the project at that stage. An innovative user configurable high level dynamic modeling tool has been developed to assist in speedy evaluation of assumptions made by the study team. This model incorporates systems or facilities that are commonly used iron ore project from mine to port. This model includes subsystems that will simulate all the logistical components, major process plant systems required for an Iron ore project. The output data provided by this high level dynamic simulation tool will enhance the confidence level of engineering carried out during the early stage of the project. This paper discusses the innovative tool capabilities and a test case comparing various techniques used in iron ore project front end studies.

Aug 1, 2018

By Paulo Conceição, Carlos Sampaio, Carlos Petter, Ariane Kuerten

The Sensor Based-Sorting technology is an emerging technology applied in mineral separation and concentration. The technique consists in using a method known as Dual Energy X-ray Transmission sorting (DE-XRT). The particle's position over the conveyor belt was evaluated and, despite de variability of results, shows that there is no a position with greater accuracy on the sensor's reading. Results obtained indicated that DE-XRT sorting technology was able to significantly reduce the mass and the ash content of the ore feed, being an interesting option for reduction of costs and improvement of coal quality in beneficiation plants.

Oct 3, 2019

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Glaydson Simões dos Reisr

Micropore organosilicas (MOs) were synthesized using methyl-phenyl-polysiloxane as precursor. The MOs were characterized using several analytical and functional techniques. The materials were assigned as micropores materials, with specific surface area up to 642 m2 g-1 and yield up to 72.55%. The adsorbents have hydrophobic surfaces and were used for removal of diclofenac from aqueous solutions. The adsorption kinetic and isothermal data were well described by the general order and Sips models, respectively. Diclofenac exhibited a better affinity than NM and the mechanism of adsorption suggested that hydrophobic groups play a key role in the adsorption process.

Aug 17, 2017

By Susanne Hahn

The Siemens VAI software model DynaPhase calculates thermodynamic properties depending on the chemical analysis of steel. It can be used online together with Siemens VAI’s secondary cooling model SIMETAL Dynacs 3D which is a unique feature. Offline it can be used to investigate the thermodynamic properties of steel grades and therefore supports the development of new grades. The core of DynaPhase is a substitutional solution model for the Gibbs free energy to calculate multi-component phase diagrams. The parameters of this model are determined by employing the CALPHAD approach. This model is combined with a microsegregation model to account for the interdendritic solidification process. New DSC (differential scanning calometry) measurements of the department of metallurgy of the Mining University of Leoben have been used to improve the DynaPhase database for high Al or Si concentrations. By comparing this experimental data to calculations it has been found that some of the widely used commercial software tools do not describe the ternary system FeAlC for high aluminum concentration correctly. In this paper we will show how thermal properties of high Al grades change with the optimized database and what impact this has on the secondary cooling of continuous casting, e.g. how the solidus point shifts on the strand. Moreover we will show that the online use of DynaPhase has many advantages for the production. Since DynaPhase uses the actual chemical analysis of the steel grade and not just concentration ranges or averaged concentrations it is possible to optimize the cooling strategy during casting for the actual chemical analysis of the actual heat.

Jul 30, 2018

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By Santiago Faucher

Molten slag from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of thermal energy. But the common slag dumping and water granulation methods used for slag treatment do not permit energy recovery. Furthermore, water is present in these processes and while operations are designed to minimize risks of steam explosions, from the contact of slag with water, these common slag handling practices have never been inherently safe. Common handling practices do permit some slags to be sold, but often in low volumes at low prices. Dry granulation offers advantages over these common slag handling practices, including the production of by-products, the recovery of thermal energy, and the eliminated consumption and safety hazards of water. For these reasons, there have been various studies in dry granulation and heat recovery, but most have never been brought to commercial scale due to scalability and cost challenges. Ecomaister- Hatch has developed and brought to commercial scale a reliable and simple dry granulation and heat recovery technology. Here we review common slag handling practices, the developments in dry slag granulation over the last three decades, introduce the Ecomaister-Hatch dry slag granulation process, and elaborate on future applications of the technology in the processing of argon oxygen decarburization and blast furnace slags.

Aug 17, 2017