Search Documents

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By Marcelo Rebellato, Leonardo Silvestre, Zhang Yongqing, Felipe Bastos, Zhang Weiqiang

This work reviews the new version of GB1499.2-2018 Chinese national standard and specification, which governs the production of high-strength reinforcing hot rolled ribbed bars in China. In addition, it discusses the main concerns from Chinese rebar makers that might affect production and application of Nb-bearing rebars, like reheating temperature required to dissolve given niobium additions, the promotion of bainite microstructure and continuous yielding, as well as Nb strengthening effects. Through extensive investigation involving both thermomechanical laboratory simulations and industrial trial, the existing state and effects of Niobium along the reheating, rolling and cooling are illustrated. At the end, optimum processing conditions have been established to produce high strength rebars for the specified requirements. The adoption of new process conditions reflected in an amount of about 20.0 million tons of Nb-bearing rebar being produced in China in 2018 with required tensile properties and microstructure, and helped rebar makers to reduce production costs considerably. Based on production data, Niobium demonstrated positive strengthening effect for high strength rebars, in particular for small diameter rebars with earthquake resistant performance. What is more, the results of the research enrich the knowledge of the application of Niobium in steels when TMCP rolling is not used.

Oct 1, 2019

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019

By Wilian da Silva Labiapari

Austenitic stainless steels are widely known for their good weldability, excellent mechanical properties for deep drawing and superior corrosion resistance in environments where most of the metals fail. Their uses include many applications subjected to a combination of mechanical and corrosive wear, such as pumps, valves and surgical implants. Although their corrosion resistance has been largely investigated, their resistance to mechanical wear is less studied. In particular, their performance under conditions involving combined corrosive and mechanical wear is not well understood. The aim of this study is to demonstrate the effect of the mechanical component on the electrochemical signal of an anodic polarization curve. A test rig was developed to investigate micro-abrasion-corrosion using a fixed ball configuration. Tests were carried out using stainless steel AISI 304 samples and 25.4 mm zirconia balls as counter bodies. The electrolyte was a 1N H2SO4 solution with SiO2 as abrasive dispersed at the concentration of 10 wt%. The results showed an increase in current density when the counter face roughness and the normal load applied during the tests are increased, evidencing a mechanical influence on the surface activity of this material in a corrosive environment.

Jul 31, 2018

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By Janaina Gonçalves Maria da Silva Machado, Carlos Mateus Braga de Almeidar, Leandro Miranda Nascimento

Knowing the reduction of the concentration of iron in the mineral load extracted in the last decades and, therefore, greater need for comminution processes, there is no denying that iron ores tend to get increasingly thin for steelmakers. In Reactors such as Blast Furnace and others of fusion-reduction, where the reduction of the iron ore for the metallic iron for the steel production occurs, we observed that one of the alternatives is to agglomerate the raw materials in the form of briquettes, improving the kinetics of the chemical reactions, since ores in the form of fines impair factors such as the permeability required for reduction. These agglomerates are composed of a reducer, fines of ferrous materials and a binder material, and require, in addition to satisfactory Metallization, mechanical resistance, avoiding losses when the compound is fragmented during transport or during its deposition in the Steel Reactor. In the following work, Briquettes were produced with Charcoal, Pellet Feed, Molasses Cane and Hydrated Lime. The mixtures were pressed under different conditions of Pressure (1, 2 and 3 tons-force), and pressing time (20 , 60 and 100 seconds), aiming to analyze the influence of these two variables on the drop tests, mechanical resistance of the briquettes generated.

Oct 1, 2019

By Jaiza Bernardo de Oliveira, Iasmim Ariane Silva, Pedro Henrique Medeiros Câmara

The process of manufacturing pig iron in the blast furnace industrial units has the consequence of the generation of slag, a waste that can be produced in high quantity and present damages to the environment, when not reused. In the composition of this tailings, it is sometimes possible to find the presence of metals harmful to nature, such as manganese, which has an important and widespread utility in the metal industries, but still, the slag ends up not being used as a potential source of this element. Knowing this, the slags were subjected to crushing and grading steps to separate the aliquots. These were applied in the tests of technological characterization of the material, from MEV, EDS, Soxhlet and analysis of liberation degree by digital microscope, finding data of several analyzes. Having said that, the objective of this paper is to demonstrate, through the characterization of the slag, that this material has in its composition metallic elements, focusing on manganese, that can be reused in order to avoid the generation of environmental liabilities harmful to the environment. The results show a manganese content with a degree of release greater than 80% in bands from 48 #, which were divided by density and thus allow the gravimetric separation of the material in question.

Oct 3, 2019

By Claude Gaspard, Stefan Wahlund, Daniel Cavalier

A point of great importance in the cold rolling process for automotive sheet is the cleanliness of the strip, particularly critical in case of batch annealing with no degreasing line or inefficient cleaning before continuous lines. In this specific cases, pollution of the strip surface could be prohibitive when rolling in the early stands of tandem mill with conventional forged work rolls as ground. The strip cleanliness strongly deteriorates during rolling particularly with high roughness rolls: iron fines are generated at the strip surface due to friction and stick on the sheet. It is well known that chrome plating on ground forged rolls in the early stands improve the strip cleanliness. This paper summarizes the results of 3D surface roughness topography studies on forged work rolls, with and without chrome plating, combined with sheet cleanliness measurement during rolling. It shows that a well determined topography has to be obtained on the work rolls used in early stands in order to roll in the mixed lubrication regime, as described by the Stribeck curve, minimizing the friction coefficient and therefore optimizing the cleanliness of the rolled sheet. The main roll roughness parameters to take into account for that purpose are the roughness level Sa, and even more, the Kurtosis parameters Sk, Spk, Svk and Ssk. The ideal surface morphology promotes deep valleys to the detriment of peaks, leading to a roll surface capable of retaining/trapping oil in the valleys, while peaks are minimized, thus reducing the friction in the roll bite and the amount of iron fines produced. To achieve this objective, new grinding wheel technologies are currently developed, in dialogue with wheel manufacturers, to create such ideal morphology of roughness well adapted to HSS forged rolls.

Oct 1, 2019

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By Frank Schrama

The Steel Plant Model (SPM) is an advanced logistic simulation model for steel plants. With the SPM, bottlenecks can be solved and logistics can be optimized. Both existing plants and greenfield designs can be simulated. All movements and actions simulated, from hot metal to cast products. Not only all major equipment and their relevant components (like a sublance) are simulated, but also ladles, scrap boxes, transfer cars and cranes. The whole plant is simulated in 3D and actual distances and speeds determine transport times. The SPM includes process time deviations and equipment downtimes for maintenance or unexpected breakdowns. This ensures more realistic and reliable results. Logistic optimization is based on comparison of different scenarios. For a new scenario, equipment and practices, etc. can easily be modified, added or removed. At the same time the SPM produces all relevant data for every new scenario, which can be presented conveniently. This makes the SPM the ultimate tool to find bottlenecks or optimize plant logistics. The SPM is validated for several plants world-wide, with different characteristics and layouts. The SPM not only realistically simulates existing plants with all utilizations, crane movements and waiting times, but also to accurately predicts the influence of plant modifications or unexpected events like breakdowns. Given the flexibility of the SPM, any (new) steel plant can be simulated quickly when a layout and the requested data are provided.

Aug 16, 2017

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Marcelo Rebellato, Beatriz Pereda, Beatriz Lopez, Pello Uranga

The classical application of Nb microalloying in the development of thermomechanical processes for flat products has been related to its suitability to enhance strain-induced precipitation and get a pancaked austenite prior to transformation. As new steel grades or new lay-outs are being developed, more complex metallurgical conditions need to be evaluated. In this context, Nb microalloying, alone or combined with other microadditions, needs to intervene in a more controlled way in additional steps of the thermomechanical process, besides its conventional strain-induced precipitation role. For example, the hardenability enhancement associated with Nb to properly achieve lower temperature transformation products, demands a proper balance of the Nb amount precipitated during rolling and the one remaining in solid solution. Similar effects are also sought when the final available Nb is used to increase strength through precipitation hardening. This manuscript evaluates how changes in the rolling strategies affect the interaction between Nb(C,N) precipitation and austenite recrystallization at different steps of the rolling process. As the possible interactions between parameters intervening simultaneously are quite complex, the application of microstructural models helps to properly define the best austenite conditioning combined with the convenient amount of Nb in solution, as a function of the final property requirements. Along the manuscript, several strategies will be discussed for the case of hot rolling of flat products comparing both normal and coarse initial austenite grain sizes.

Oct 1, 2019

By Vera Lúcia Othéro de Brito

Literature has shown that spinel Co-Mn ferrite have potential application in magneto-mechanical sensors, due to its relatively high magnetoelastic sensitivity. In this work, Co-Mn ferrite was processed by means of the ceramic method, using Fe2O3, MnO and Co3O4 as raw materials. Samples were liquid-phase sintered, using Bi2O3 additive as liquid-phase former. X-ray fluorescence analysis was carried out in the raw materials in order to evaluate their impurity content. Atomic absorption spectrometry analysis was used for quantifying the Co/Mn/Fe proportion in the ferrite. The microstructure of the sintered sample was analyzed by means of Scanning Electron Microscopy. The magnetization and magnetostrictive behavior of the ferrite were evaluated, obtaining curves for magnetic hysteresis, magnetostriction and magnetoelastic sensitivity. The impurity inclusions and the Bi-rich particles formed from the liquid phase were characterized. The sintered ferrite had a total magnetostriction of -126ppm, which is lower than the values reported in literature for a Co-Mn ferrite of similar composition. It was verified that sintering was carried out within a critical temperature range, in which the decomposition of Mn ferrites may occur when sintering in air. This decomposition affects the magnetic properties of the material, and it may be avoided by using controlled sintering atmospheres.

Aug 8, 2018

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

In today’s competitive steelmaking environment, the optimization and continuous supervision of the blast furnace process is of major importance. Modern probes and process measurement systems can assess the specific operation of the blast furnace. They provide a better and detailed process understanding and control. The benefits are even more important when they are combined with process models and expert systems. Everyday operation, productivity and even the lifetime of a blast furnace can be significantly improved by collecting, interpreting and acting upon such process data correctly. Only a comprehensive knowledge of the various process phenomena together with measurement of process variables inside the blast furnace enables the operators to optimize coke and fuel rates, to run the blast furnace smooth, reliable, and safe, and to make best use of the available raw materials. While the improvement of the blast furnace process with respect to productivity remains the main task, also, the timely identification of abnormalities and the assessment of process variations is an objective. This paper describes the blast furnace measurement systems that are available for everyday automatic use and provides an understanding for the possibilities of modern probes. The different applications are daily blast furnace supervision, charging process optimization, and observation of the internal state. Finally, the paper gives recommendations on probe configurations for different blast furnaces sizes, considering both a technical and an economical point of view.

Aug 2, 2018

By Frank Schrama

Steelmakers worldwide agree that the most efficient and cost-effective solution in BOF steelmaking is to desulfurize the hot metal between the blast furnace and converter. Various methods are currently in use, among which the Kanbara Reactor (KR, using only lime as a reagent), Magnesium mono-injection (MMI, using only magnesium; also known as the Ukraina-Desmag process) and co-injection (using magnesium and lime/CaC2) are leading. These three hot metal desulfurization methods are compared based on metallurgy, efficiency, costs and overall performance. Both available data from literature and experience from Danieli Corus engineers is used for this study. The KR process is able to reach low sulfur concentrations (> 10 ppm) in hot metal and has lower reagent costs. However, due to higher Fe-loss and heavy wear the KR process has the highest operational costs. The Magnesium mono-injection process is very fast due to the use of the reactive magnesium as reagent. Major problems with resulfurization (sulfur levels below 50 ppm cannot be reached) and the violence of the process made that this process could never get a firm foothold in the western steel industry. The co-injection process with magnesium and lime proves to be able to combine the best of both worlds. It can reach low sulfur concentrations and desulfurize fast. Co-injection is also the most flexible and cost effective.

Aug 16, 2017

By Nelson SOUTO, Nicolas LEGRAND, Christian COUNHAYE, Don EARLEY

The work is motivated by the automotive customer requirements for a roughness with high peak density (RPc > 75 peaks/cm) on steel sheet surfaces to maintain a good strip surface finish after painting. For that purpose, a new approach is utilized to compute roughness transfer and predict final roughness on uncoated steel sheets (average roughness, skewness, peak density) as a function of temper rolling conditions. The approach is based on the Monte Carlo method combined with the Abott curves and an auto-correlation function to numerically generate roughness profiles for roll and strip respectively. To compute the roughness transfer due to the interaction between roll and strip surfaces during rolling, a composite Abott curve that combines roll and strip Abott curves is used with an asperity crushing model integrated with a rolling model. This enables simulating two roughness transfer mechanisms in the roll bite: the strip asperity crushing mechanism by roll roughness and the strip asperity ploughing mechanism due to roll-strip interfacial sliding speed. The model shows the importance of considering the two mechanisms to predict roughness transfer correctly when strip elongation is high, typically a few percent, and roll bite friction is low. In these conditions, the forward slip at the exit of the roll bite tends to erode strip roughness significantly and decrease considerably the peak density on the strip. For lower elongation levels (~1%) and high roll bite friction, the ploughing mechanism becomes negligible and roughness transfer is controlled by the crushing mechanism only. With these two mechanisms, the model reasonably predicts the evolution of average roughness and peak density over a wide range of temper rolling conditions (new/worn work rolls, hard/soft grades, various elongations), but skewness is more difficult to predict for some trials.

Oct 1, 2019

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Mark Gilliam

Control of true steel level in the tundish during casting is desired in order to maintain the correct pressure head and thus provide a stable flow to the mold. Also the control of tundish draining prevents slag carryover and can increase yield at each end of cast sequence. At Steel of West Virginia (part of the SDI Group), it was understood that to be able to measure the true steel running level and control the drain level at the end of casting would be a great benefit during production at their three strand billet caster. This paper sets out to show how an evaluation process was started to find the best method to determine steel level in the tundish and to prevent the steel level dropping low enough to allow slag to enter the mold. Also how the decision was taken and a real time molten steel measurement system was installed and by utilizing the resulting data in the process, how slag in the mold was removed as an issue, how lost production was reduced and how consistent steel level has provided constant casting speeds and improved stream integrity, all leading to realized quality improvements. Other areas discussed within the paper will be the training of operational staff, the difficulties to be overcome when first installing new equipment and how these teething problems were cured by close co-operation between the steel plant and the equipment suppliers. In conclusion the paper will discuss the production improvements achieved, production cost savings at the plant and how the generated data was integrated into the plants process control system.

Aug 16, 2017