Search Documents

By Daniel Carvalho, Marcos Viana, Leonardo Demuner, Herbert Castro

Intensive process and technology improvements related to the BOF converter — the key process to increase steel plant productivity and stability — have been performed at Ternium Brazil. This paper details the road map for process developments and investments in equipment technology, as well as the results achieved. The main topics of this development are the process control and optimization systems, slag forming model, oxygen blowing pattern, end-of-blow point control and slag carryover control. The outcomes of this development are improvements in the reblow rate, end-of-blow oxidation, direct tapping, slag carryover, slopping ratio, metallic yield and lining life.

Oct 1, 2019

By Samuel Filgueiras Rodrigues

An austenitic stainless steel ISO 5832-9 was deformed in a torsion test machine over the temperature range of 1,000°C – 1,200°C and strain rates of 0.05, 0.1, 1.0 and 5.0s-1. The Steel plastic behavior was studied by analyzing the flow curves shapes and using the constitutive equations under the conditions of thermomechanical treatment. The curves initially presented an increase in stress characterized by hardening work, followed by a drop in stress to an intermediate level that reached or not, for certain conditions, the steady state softening. The plastic flow curves of ISO 5832-9 steel displayed in three different ways: (i) Curves with continuous softening presenting plastic instability for low temperatures and high strain rates; (ii) curves type flat, here after the peak there is little variation of stress with strain presenting softening mechanism by higher contribution of dynamic recovery at low temperatures and low and intermediate strain rates; (iii) curves with softening after the critical deformation favored by high temperatures and low strain rates. These behaviors indicate the influence of the stacking fault energy (SFE) and precipitated particles on the softening kinetics of this steel.

Aug 8, 2018

By Henry Chumienski

Next to the paper industry, the steel industry is a major user of water. Without an adequate and reliable source of “good” water, steel cannot be produced. The use of water has a direct impact on steel quality and on our environment. Used improperly, water can also add unnecessary costs. Used properly, water can maintain and improve steel quality, enhance our environment and control or reduce the “total cost of operation”. Water needs to be more than just “wet and not lumpy”. Water quality needs to be based on the end use. This paper discusses ways to manage many of the water systems. With little or no capital investment it is possible to develop operating practices that protect your initial investment, ensure that the water systems do not have a negative impact on quality or your production costs and also minimize your chance of having an environmental incident.

Jul 30, 2018

By Yuechang Wang

A new method of manufacturing the wavy-tilt-dam(WTD) mechanical seal has been mentioned. In this method, the special equipment is designed to provide a predetermined force to external and inner circular surface of the ring. After milling the end face of the seal by grinding miller and releasing the preload, the wavy-tilt-dam can be done on the seal surface. In this paper, a prediction model is built up to investigate the relationship between the predetermined force and the deformation on the surface of the ring by using ANSYS software. A WTD ring is manufactured by this method which approves that the prediction model is in accord with the real process and this manufacturing method of the WTD mechanical seal is a proper choice.

Jul 31, 2018

By Wujian jun

In the process of wire rod production, the rolled wire products must be cooled from the red-hot state to the normal temperature state. How to cool the wire rod after rolling is one of the key links of product quality control in the whole wire rod production process. In this paper, combined with the closed-loop transformation project of controlled cooling temperature of Xuanhuan iron and steel group co., LTD., the closed-loop related controlled cooling equipment (including water cooler, valve table, etc.), nozzle layout and process layout of water tank, and closed-loop software control system of controlled cooling temperature of high-line are analyzed and designed. Closed-loop system design USES temperature of cooling water cooling and water cooling two temperature closed loop regulating circuit, through temperature feedback and feedforward to achieve the uniformity of temperature adjustment, in order to prevent occur due to temperature closed loop control function with the phenomenon of a steel before and after the temperature difference is bigger, system Settings have "absolute temperature regulation" and "relative temperature regulation" selection mode. The system has a self-learning mode, which can modify the temperature feed forward formula. In addition, this paper takes the hard wire 82B rod as the test object, and studies the process parameters and the comprehensive mechanical properties of the rod before and after the water cooling system reform. The research results show that the temperature closed loop system, can ensure the rolled piece temperature control precision of plus or minus 10℃, enhances the stability of wire rod cleaner performance. It can reduce water consumption by about 186m3/h and improve the utilization rate of cooling water.

Oct 1, 2019

By Alessandro Pigani

Over the last 25 years the thin slab casting and rolling process has been gaining a major market share in the production of hot rolled strip, progressively eroding the areas previously of exclusive domain of conventional mills. This is mainly thanks to the competitiveness of the process over conventional ones, and to the growing ability of this technology to cover the majority of market niches, well beyond the boundaries of the commodity market. After having significantly contributed to the continuous expansion of this production mode and after an extensive campaign of theoretical research and physical testing in reference plants, Danieli has progressively developed over the years a new generation of thin slab casting and rolling layout, marking a new phase in the evolution of this process. The new step-ahead is epitomized by the name QSP-DUE. This configuration belongs to the Quality Strip Production (QSP) family, which is Danieli’s strip-quality-oriented thin slab based plants. The innovative features of the process are embodied in the acronym DUE, which stands for Danieli Universal Endless (Danieli patented technology – US patent n. 8087449, January 3rd, 2012). What makes this new concept different is the ability of “universal” rolling modes thanks to the fact that, now, within one single plant it is possible to perform coil-to-coil, semi-endless and endless rolling modes, making this plant a major technology innovation compared to the previous generation.

Aug 16, 2017

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Lara de Assis Moreira, Vinicius Thiago Lecco Rampinelli

The energy efficiency of reheating furnaces is a continuous challenge, as these equipment consume a representative portion of the total fuel of an integrated steel plant. Therefore, any investigation and implementation which brings improvement in this figure become an important issue for the mill competitiveness. In the case of production delays due to external factors (the condition addressed in this work), whether predicted or unforeseen, the slabs remain inside the furnace with high temperatures in order to avoid production delay during the production restart, elevating the specific consumption and scale formation. This work increased the energy efficiency of the two ArcelorMittal Tubarão’s walking beam reheating furnaces, by reducing the consumption of mixed gas during production delays (either scheduled or not) lasting less than 3 hours. The objectives were achieved through improvements, among them, tuning of Level 2 automation system parameters, automatization of procedures and operational training. The work resulted in a 34.4% fuel gas consumption reduction during the delays.

Oct 1, 2019

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By Roberto Silva de Andrade

O inchamento é um grande problema durante a redução de pelotas de minério de ferro. Várias mudanças podem ser feitas nas pelotas para minimizá-lo. Conforme o sínter utilizado se torna cada vez mais básico, pelotas mais ácidas são desejadas. A adição de MgO, assim como a modificação da basicidade binárias das pelotas pela adição de CaO são soluções que têm sido apontadas. Dessa forma, este trabalho estudou os efeitos do MgO a da modificação da basicidade binária nas seguintes propriedades de pelotas: compressão a frio, porosidade e índice de inchamento. Foram preparadas pelotas com até 5% de MgO e com basicidades entre 0,67 e 1,5. O aumento do teor de MgO causou aumento de porosidade e queda de resistência. A basicidade diminuiu a porosidade e causou aumento de resistência nas pelotas de basicidade 1,0. Tanto o aumento de basicidade quanto a adição de MgO diminuíram o inchamento.

Oct 30, 2017

By Mariana Carla Mendes Rodrigues

The present study deals with the effects of strain rate on the functional behavior of NiTi thin wires. The samples, in the austenitic condition at room temperature, were mechanically cycled 20 times by loading up to 6% strain followed by complete unloading, at 25°C. Four different quasi-static strain rates were assessed: 1x10-4, 1x10-3, 1x10-2 and 5x10-2s-1. The functional properties are described by means of critical stress to induce martensite, stress at maximum strain, energy dissipated per cycle and residual strain. The sensitivity of repeated cyclic deformation to strain rate is also analyzed in terms of phase stability. The results show that the fluctuation in the loading plateau, due to non-homogeneous transformation, increases with increasing strain rate. During cycling, it is observed that higher strain rates result in lower critical stress to induce martensite after the 5th cycle. However, the stress at maximum strain is higher at high strain rates, regardless the number of cycles. The accumulation of residual strain also increases with the strain rate due to the higher applied stress. During unloading, both the elastic deformation of stress-induced martensite and the reverse transformation seem to overlap at high strain rates. The dissipated energy behavior changes between the 1st and 20th cycle. No martensite is stabilized after training, but the intensity of the X-ray diffraction peaks of austenite increases with strain rate, as a result of stress relaxation.

Aug 17, 2017

By Carlos Martins de Oliveira

The trucking industry is constantly seeking improvement and cost reduction of their vehicles, studying new lighter and robust materials to meet the needs of its customers. The objective of this work is to study the application of DCPD Telene, PU. R. RIM and PP-TD 20 materials in aesthetic components of trucks: bumper, calender, upper and lower bracket and side air deflector. A multifunctional work team was created to work in such parts of IVECO trucks. The work began with an analysis of possible improvements to the current parts and followed the subsequent phases: definition of new materials, virtual modeling, new tools, and durability test in vehicles. It could then be verified that the proposed DCPD Telene, PUR. RIM and PP-TD 20 materials showed greater strength, better painting surface, and reduced weight and cost in parts.

Aug 8, 2018

By Marcus Weldon

We are at the beginning of an era of profound transformation and human progress — a new industrial revolution. This “Automation of Everything” era will be brought about by digital interfaces, data analysis and control of the physical world through networks employing the Nokia Bell Labs Future X1 architecture — networks to support the digitization and connection of everything and everyone with the goal of automating much of life. The interconnection of robots, machines, drones, sensors, processing platforms and people through Future X networks will provide transformative tools for the automation and optimization of factories and warehouses, ports, electric grids, transportation networks, food, healthcare, construction, logistics and supply chain, emergency response, mining, and other physical industries. To date, the level of automation has been modest at best. Automating these physical industries — industries that account for 70 percent of the US Gross Domestic Product, for example — has the potential to drive significant increases in the world’s economic productivity.2 Realizing the potential of this next industrial revolution will require billions of wirelessly connected endpoints for high fidelity physical-to-digital conversion, millisecond response times to tightly control and coordinate machines and robots, and intelligent analysis to optimize real-time decisions — tasks beyond the reach of current networks. Increased levels of automation are already being achieved through the use of 4G advanced wireless access technologies. The untethering of sensors and actuators in industrial environments through the low-latency, high-bandwidth, high-reliability, and massive scale provided by 5G wireless access will complete this evolution, providing an unprecedented ability to digitize, analyze, comprehend and manipulate the physical world at a scale never previously thought possible. These new capabilities will enable us to create digital models of the physical world with ever higher levels of fidelity, further enhancing our ability to improve operational efficiencies and increase productivity and worker safety. Doing this will require a dramatic evolution in network architecture toward massively distributed cloud control and baseband capacity to achieve the required ultra-low latency and ultra-high bandwidth for industrial and infrastructure automation services — the Future X architecture. In early 2019, Nokia Bell Labs will publish a sequel to “The Future X Network: A Bell Labs Perspective”. “Future X for Industries: A Nokia Bell Labs Perspective” will explore how the Future X architecture will automate many of the world’s physical industries, including chapters devoted to electric power, cities, rail, mining, public safety, manufacturing, ports, logistics and supply chain, and an overarching chapter devoted to securing this highly automated world. To give you a small taste of the feast that’s to come, we’re sharing with you an initial installment — “Future X for Industries: Mining” — the Nokia Bell Labs view of how mining will be transformed through a Future X architecture..

Oct 1, 2019

By Natália de Oliveira Roque Maciel

Atualmente uma das maiores preocupações da humanidade está relacionada as questões ambientais, o que tem motivado a pesquisa e o desenvolvimento de materiais provenientes de recursos renováveis e ambientalmente amigáveis. A despeito disso, este trabalho objetiva comparar a resistência de compósitos desenvolvidos com fibras naturais e, portanto, ambientalmente amigável e de compósitos desenvolvidos com fibras de vidro, que por sua vez apresentam impactos ambientais desde a fabricação até o descarte. Foram fabricados 13 corpos de provas para amostras contendo 0% de fibra, 30% de fibra de curauá e 30% de fibra de vidro na matriz epoxídica e ensaiado na máquina de tração. Os resultados obtidos apresentam valores bastante superiores para as amostras contendo fibras de vidro, contudo, ao relacionar a tensão do compósito com a respectiva densidade da fibra, foi possível constatar que os compósitos com fibras naturais chegam a apresentar resultados superiores aos compósitos fabricados com fibras de vidro. É possível concluir, portanto, que do ponto de vista da propriedade mecânica em questão é possível substituir as fibras de vidro por fibras de curauá.

Aug 17, 2017

By Vitor Guarnier Domiciano

A necessidade de melhorar as propriedades dos refratários monolíticos para resistir às condições operacionais cada vez mais severas e instáveis das casas de corrida de Alto-Forno tem sido um grande desafio para os fornecedores de refratários de maneira a garantir a segurança dos canais de corrida e sua disponibilidade para operação. Este trabalho apresenta as propriedades de novos concretos refratários Al2O3-SiC-C (aplicados por vibração ou bombeamento/projeção a úmido) desenvolvidos para resistir ao severo mecanismo de corrosão que ocorre na linha de gusa de canais principais e que exige constante atenção dos operadores das casas de corrida. Testes realizados com os novos concretos refratários em canais de corrida principais de diferentes Altos-Fornos de grande produtividade revelaram uma significativa diminuição da velocidade de desgaste do revestimento refratário na linha de gusa oferecendo uma condição operacional segura e confiável às casas de corrida.

Aug 16, 2017

By Marcela Gotelip Barbosa

Pellets are the main iron input to the blast furnace at ArcelorMittal Lazaro Cardenas iron and steel making facility in Mexico. Pellets are made at this facility using the concentrates generated and shipped from their captive mines viz., Las Truchas, Pena Colorada, Volcan Sonora. The concentrating plants, after grinding the ore to the liberation size, use magnetic separation and flotation to reject the silica, sulphur and phosphorous impurities. At Volcan Sonora Mines, the ore is contaminated with phosphorous minerals, and hence, after magnetic separation, the phosphate minerals are floated using anionic carboxylate collector (sodium oleate). Apart from floating the phosphate minerals, the sodium oleate also has some tendency to smear on the iron bearing mineral surfaces leaving a hydrophobic surface, which is expected to reduce the green pellet strength due to absorption of ultrafine sized air bubbles on these surfaces, and further generate higher levels of dust during the induration process. In order to alleviate this industrial problem, comparative studies were carried out on the concentrates from magnetic separation using reagents from synthetic sarcosinate and carboxylate family collectors. Results have indicated that the sarcosinate family members not only were found as replacement to carboxylate collectors, but also reduce the phosphorous content below the values achieved with oleate, thus have considerable benefits in the downstream steel making process. Based on the results, plant runs are being taken up at Volcan Sonora. In this article, the laboratory results obtained on iron grades and recoveries, and phosphorous rejection using both the reagents are presented.

Aug 1, 2018

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Márcia Maria da Silva Monteiro Pereira

Durante o lingotamento contínuo de aço, partículas de ZrO2 adicionadas na escória de molde facilitam a nucleação heterogênea de cristais devido à sua limitada solubilidade. A adição de ZrO2 promove a cristalização da fase cuspidina, o que auxilia na redução da transferência horizontal de calor no molde, amenizando desta forma o problema das trincas longitudinais. Outro benefício da adição de ZrO2 em pós fluxantes é reduzir a taxa de desgaste da válvula submersa (SEN) na interface metal/escória; a erosão da SEN é um problema sério. Através de testes de laboratório e de testes industriais concluiu-se que a adição de ZrO2 em pós fluxantes reduz a taxa de transferência de calor horizontal no molde durante o lingotamento contínuo de aço, considerando os dois tipos de pós fluxantes que foram analisados no presente trabalho. Além disso, observou-se que a adição de ZrO2 reduz a taxa de desgaste da válvula submersa na interface metal/escória.

Aug 16, 2017