Search Documents

By Jorge Madias

Pin holes as a surface defect, and blow holes as an inner defect, occur in billet / bloom / beam blank casting, particularly for Si-Mn killed steel cast with metering nozzle and oil lubrication. If they are present in abundance or have a large size, they may originate defects in the rolled products. Their characteristics, factors behind their formation, as well as usual processing conditions that promote their occurrence are discussed. Finally, the evolution of these defects during reheating and rolling is analyzed, with industrial examples.

Aug 16, 2017

By Pedro Augusto David Machado

The hot metal produced in small blast furnaces runs with a highly heterogeneous charcoal. The result is a significantly higher hot metal chemical composition variation, especially for the silicon content, which varies from 0.4 to 1.5% in Mini Blast Furnaces - MBFs, designed to feed an EAF and/or a BOF. These MBFs operate with frequent variation in their productivities to feed preferably only one of the steelmaking reactors, that is, EAF or BOF. The hot metal suitable amount, chemical composition and temperature, to be delivered at the steelmaking vessel, become the major concerns in the integrated operation MBF to EAF or BOF. In order to cope with those undesirable frequent variations, a solution has been proposed based on the existing technologies of oxygen jets and ladle refining techniques adapted to a hot metal ladle or to a Torpedo Car. The proposed technique is not only able to adjust hot metal temperature and chemical composition, but it also generates the adequate conditions for refinement from P and S, as well as “cleaning” hot metal ladles and Torpedo Cars by melting pig iron skulls. Therefore, this new technique development results in high hot metal yield, an adequate chemical composition and bigger campaign of hot metal ladle.

Aug 17, 2017

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Edo Engel

Whereas only a handful of decades ago, typical blast furnace working volumes were below 1000 m³, such furnaces are currently designated compact or even mini blast furnaces. For certain business cases, however, small furnace sizes remain an attractive option. Decades ago, this size blast furnace would have produced a maximum of 0.3 Mtpa with its 600 m³ working volume over a campaign of up to four years. The current state of technology and operational know–how will allow a similarly sized furnace to produce over 0.7 Mtpa while achieving the multiple decade campaigns that have become familiar to steel producers in full sized operations. This level of productivity, but especially the reliability and supply security associated with mature technology, allows for integration into minimills or taking a first step towards a full scale BF–BOF integrated mill. Steel producers considering such scenarios, which are typically attractive for emerging economies, are confronted with fundamental decisions, one of which is for the technological basis for the compact or mini blast furnace to be included in the plant. This article addresses some of these decisions from an operations–based perspective. A small number of case studies is included.

Aug 16, 2017

By Konrad Krimpelstätter

The need for more effective and flexible roll-gap lubrication technologies in hot and cold rolling mills is steadily increasing due to ever-greater requirements placed on the rolling process and the final products. In particular, the rolling of high-strength steels poses enormous demands for both the rolling mill and the coolant/lubricant to be used. The presented paper focuses on two innovative technologies for highly efficient roll-gap lubrication for hot and cold rolling, which were developed utilizing extensive knowledge and expertise about the tribological interactions in the roll-gap. The advanced work-roll lubrication package (A-WRL) for hot rolling and ESP mills is using specially designed mixer-nozzle units to mix the water/oil emulsion very close to the nozzles to minimize the risk for contamination and clogging. The nozzles are quickly exchangeable and are optimized to ensure uniform lubricant distribution, high plateout efficiency and minimum oil consumption. This eco-friendly solution does not require any chemical additives or cleaning agents and significantly reduces electrical energy consumption and work-roll wear. The roll cooling system on mill entry and exit side remains switched-on, which is of vital importance especially for highperformance hot strip mills. Minimum Quantity Lubrication MQL® represents a new generation of roll-gap lubrication technologies for cold rolling, which applies minimum amounts of pure rolling oil finely atomized with pressurized air directly onto the work roll surface. This allows controlling the oil film thickness depending on actual process and product parameters, providing increased lubrication flexibility, significant improvement of strip surface cleanliness through reduction of strip wear. MQL® was successfully installed and tested on two industrial tandem cold rolling mills in Europe. Advanced WRL and MQL® represent Primetals’ latest technologies that feature a robust and reliable system comprising standardized interfaces and flexible communication options. Both packages can easily be integrated into existing or new hot strip mills, ESP lines or cold mills.

Aug 17, 2017

By Gerd Weyand

Gontermann-Peipers GmbH (GP) Germany developed a new, high alloyed steel grade for the manufacturing of back-up rolls. The advanced GP double pour casting processes provide highest flexibility in being quite open in rolls work layer chemistry and hence microstructure with no influence on core respectively neck properties. GP took the process advantage to provide a brand new back-up roll grade with remarkably reduced roll wear while operating with textured work rolls. In the meantime several successful trials have been made with this new roll grade on different Skin Pass Mills. As a result the performance of back-up roll and thus availability of mill will be improved while specific costs for mill will drop. This quite new back-up roll grade has recently been launched. As next step increasing the field of applications is under progress.

Aug 17, 2017

By Priscilla Pessin Coppo

The prevention of dental enamel wear has particular relevance for preventive and restorative purposes in dentistry. The wear damage can increase due to salivary disorders and/or parafunction (bruxism); antagonists incisal surfaces become flat and coincident. This study aims to investigate the wear behavior and the related mechanisms in sliding pairs of conformal incisal enamel, with similar values of hardness and fracture toughness, with different applied normal loads and lubricated conditions. Bovine incisors, under pin on flat configuration, were tested in two lubrication condition (dry or with natural saliva) and two applied normal loads (8 and 16 N). The worn surfaces were investigated by 3D profilometry and SEM. The analysis of worn surfaces indicated mechanisms of brittle fracture, but with different severities. Under a normal load of 16 N and dry condition, wear is controlled by a brittle process: microcracking with flake-like wear particles, which results in high friction coefficient (> 0.85), wear rate and wear volume. On the other hand, under a normal load of 8 N and natural saliva, wear took place in the interprismatic region, with consequent exposure of prisms and fracture in localized regions. In this case, the friction coefficient was 16% lower and the wear volume was one order of magnitude lower. Under 8 N and natural saliva, the wear was greater than in the dry condition, probably due to tribochemical reactions.

Jul 31, 2018

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By Andrea Pezza

The steel market is experiencing a difficult conjuncture: on the one hand steel producers minimize their investments while optimizing their over- production, on the other hand suppliers reduce their internal human resources and capacity in order to overcome the instability of the new era. A return to the steel production levels of the past is not expected in the short term. Research, development and plant concept optimization is one recipe to drive the future of the steel business. This article describes a new concept for a VOD plant developed as a result of thorough investigation and assessment of all possible solutions. A joint and tight cooperation with the final customer was necessary to reaching important results. This article consists of the contributions from the plant suppliers in terms of their experience and feedback, as well as the final user’s. The final customer, voestalpine Giesserei Linz GmbH, and the plant supplier, Primetals Technologies, are both worldwide players and highly focused on reaching best quality and innovation.

Oct 30, 2017

By Benito Barbabela e Silva

O pelotamento é a mais complexa etapa de aglomeração de finos de minério de ferro. Sua resposta é naturalmente oscilante, sendo bastante influenciada pelas características físicas obtidas nos processos de beneficiamento mineral que a precedem e tem papel crucial para a etapa de tratamento térmico de sinterização à jusante. O presente trabalho aborda o processo de classificação de pelotas verdes, sólidos singulares de aspecto deformável e pegajoso, em peneiras de rolos por modelamento por aplicação de Método dos Elementos Discretos. Esta técnica mostra-se como uma importante ferramenta pois supera as limitações impostas na modelagem física (quantificação e identificação de fluxos por ausência de instrumentação em escala industrial, amostragem sem representatividade) ao reproduzir de forma verossímil as repostas do sistema para importantes variáveis de controle: comprimento de gap, umidade, dispersão de tamanhos e resistência das pelotas.

Oct 30, 2017

By Hui-bin Wu, Rui Yuan, Yang Gu, Peng-cheng Zhang, Zheng-zhi Zhao

The corrosion behavior of three kinds of medium-Cr rolled steel pipeline steels in carbon dioxide collecting and transporting environment at different temperatures was studied. The results shew that the 5Cr sample was most affected by temperature. When the temperature rised from 30 °C to 90 °C, the corrosion rate increased from 0.12 mm/a to 1.87 mm/a, which was increased 15.6 times. The corrosion rate of 7Cr steel at 30 °C was similar to that of 5Cr steel. However, as the temperature increased, the corrosion rate rised slowly, increasing by 2.4 times at 90 °C. The corrosion rate of 9Cr steel was not obvious with temperature, and it was always below 0.06 mm/a. The thickness of the corrosion product film of the three samples gradually increased below 70 °C, and suddenly increased above 70 °C. This was related to the negative temperature coefficient of the solubility of FeCO3, and the thickening of the product film also affected the ion exchange of the cathodic reaction. An increase in the Cr content contributed to grain refinement and increased the proportion of the small-angle grain boundaries. More fine grains mean an increase in the total length of the grain boundaries, which could provide a diffusion channel for the free Cr element; on the other hand, the low-angle grain boundary structure was more orderly, with a lower free volume and lower interface energy. Under the combined effect of both, 9Cr steel and 7Cr steel had high volta potential and better corrosion

Oct 1, 2019

By Douglas Glenn Stalheim

Production of structural hot strip coils in yield strengths up to 700 MPa and higher is increasing worldwide. In addition to requiring higher strengths, structural designs require good formability, toughness and weldability. Toughness and formability come from optimization of ductility properties while weldability comes from lower carbon equivalent alloy designs. The key to the production of optimized cost effective hot strip produced structural coils is to create the correct balance of a proper alloy/processing design to create as fine and uniformly distributed cross sectional grain size as possible. In addition to the creation of the fine/uniformly distributed cross sectional grain size, the correct microstructure needs to be created. In the higher yield strength grades, not only does the grain size/distribution play a role but a proper understanding and control of microalloying precipitation kinetics is required. This paper will present various examples of hot strip alloy designs to produce cost effective hot strip structural coil in yield strengths up to 700 MPa with good ductility and weldability. In addition, steelmaking/casting parameters will be discussed to assure successful production. Optimized reheating, rolling and cooling parameters of these alloy designs will be introduced in an accompanying paper.

Aug 17, 2017

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By Robin Schott

The blast furnace process is the most important process to produce pig iron. The necessary process energy is mainly covered by coke. But the production of coke is connected with CO2-emissions and high costs. A significant measure to reduce the coke rate and with it the CO2-emissions plus costs is pulverized coal injection (PCI) through the tuyeres into the blast furnace. A further increase to substitute coke by coal can be achieved by using the Oxycoal+ technology. This article compares and shows the cost effectiveness and the decrease of CO2-emissions with the help of simplified energy balances for the only coke operation of the blast furnace, the operation using pulverized coal injection and the operation using the Oxycoal+ technology.

Aug 17, 2017

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Piotr Kula

Vacuum carburising with pre-nitriding (PreNitLPC® technology) involves feeding ammonia during the charge heating stage before carburising. The purpose is to restrict the growth of grain in the surface layer of the carburised steel. The article presents the influence of nitrogen on restricting austenite grain growth during vacuum carburising and on mechanical properties (fatigue strength, impact resistance) of layers that underwent such treatment in comparison with traditional carburising methods.

Aug 16, 2017

By Maurizio Massimo

Danieli developed the “3Q” suite of process control technologies to address three critical principles: delivering the highest product Quality, in the required Quantity, with Quickness of response required for today’s casting machines. Ever increasing market demands for productivity and slab quality necessitate the latest advances/improvements in equipment design, process technology, and control software for all types of slab casters, and Danieli boasts a unique experience that extends from ultra high-speed thin slab casters to extra high-thickness conventional slab casters. The “3Q” system is monitored and controlled by a unique, intelligent HMI incorporating. Touch screen technology and Operator Assistant tablets. Operator Assistant is a tablet based system that guides the operator through the plant process, so that in the event of a process change or an alarm the operator is automatically presented with the choice of possible solutions / actions. The comprehensive range of technological packages cover all aspects of caster design and automation control, from feeding of liquid steel into the tundish to the final slab leaving the caster.

Aug 17, 2017

By Peter Grawenhof

In steel mills universal joint shafts, slipper spindles and gear spindles are used to overcome the design- and process- related offset between the axis of the motors and the work rolls. At the roll side the available space for the couplings is limited by the minimum work roll diameter. This leads to extremely high loaded components of the universal couplings especially at the roll side joints. Furthermore modern steel mills continuously strive to roll larger plates and materials with increased strength. This requires drive solutions with even higher torque capacity. For these applications conventional design joints are not sufficient anymore. Even alternative solutions such as hybrid- or offset- designs fall short. Therefore the companies Voith and BUMA Engineering developed together the new GearLink drive concept in close cooperation with the Voestalpine Grobblech GmbH. A completely new combination of universal joints and gear couplings offers an up to now unique solution enabling the use of 1,35- times bigger joint with a 2,5- times higher torque capacity and a 20- times longer lifetime. The GearLink system was first time successfully taken into operation at Voestalpine Grobblech in December 2013 and is up to now working without issue.

Aug 16, 2017

By D. A. Aranda-Regino, C. Gómez-de-la-Garza, J. Ramírez-Cuellar, L. A. Leduc-Lezama

The Pickling Line Tandem Cold Mill (PLTCM) at Ternium’s Pesqueria plant with a 5 stands, 6 high configuration started in 2013. At the time of the start up the work roll specification and grinding practices were stablished following a low risk policy to be able to sustain any start-up associated accident. Once a stable operation has been achieved both these policies are being modified to improve productivity and reduce costs. The specified hardness of the rolls has been increased and efforts are being made to optimize the grinding according to the rolling campaign length and materials. The fatigue damage in work rolls, after rolling and its removal by grinding was followed by hardness measurements made at the end of the rolling campaign and after grinding. Softening of the rolls after rolling was found mainly in final stands to be related to the averaged stress experienced during the campaign, the original roll hardness was recovered after grinding. Hardness evolution was also followed after each grinding step finding that the total amount of grinding could be reduced. The grinding practice was modified accordingly for the first stands and the yield of work rolls in them has improved.

Oct 1, 2019