Search Documents

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Diego José Inforzato

Hot tensile data were correlated with creep data, in Aluminum Alloy AL7475-T7351, as part of a broader research program, aiming at the validation of a methodology that proposes an equivalence between the two kind of results, for metallic materials in general. The methodology is based on a criterion that establishes correlation among the following parameters from each test: the strain rate, ultimate tensile stress, and time to reach the ultimate tensile stress, in tensile tests, are equivalent respectively to the: minimum strain rate, applied stress and rupture time, in creep tests, for a given test temperature. The present material was tested at 3 temperatures: 133,166 and 193ºC, using 3 nominal tensile strain rates in the hot tensile tests: 3.2x10-6, 1.6x10-4 and 6.4x10-3 s-1 and 9 applied stress levels in the creep tests, varying from 140 to 400 MPa. The conversion of the hot tensile data to creep-like data allowed performing the analysis of all the results together according to the traditional creep relations proposed by different authors, namely: Norton, Arrhenius, Zener-Hollomon and Monkman-Grant, with the determination of the corresponding parameters in each case. The equivalence between hot tensile and creep data is also confirmed for this aluminum alloy.

Aug 8, 2018

By Rodrigo Ribeiro de Andrade, Túlio César Nogueira, Ed Juarez Mendes Taiss, Nilton José Lucinda de Oliveira

The objective of this study was to determine the effects of an eventual slab central macro-segregation in microalloyed steels with low Mn content (0.80%) and high Nb content (0.08 to 0.10%) on the kinetics of recrystallization of austenite during its rolling, on its critical temperatures, that is, of non-recrystallization (Tnr), start Ar3 and finish Ar1 of ferrite transformation and its response to a simulated industrial thermomechanical processing. The determination of the austenite recrystallization kinetics was made through isothermal double compression tests using a dilatometer, while the critical temperatures were determined through hot torsion tests in a Gleeble® 3800. It was found that austenite recrystallization kinetics, Ar3 and Ar1 temperatures did not present significant changes for the samples extracted both at ¼ of the thickness and at the core of the plate, indicating that, as expected, the central segregation in this type of steel was not intense to the point of affecting this phenomenon. The Tnr values determined for the samples extracted in the core of the plate were, on average, 30°C lower than those obtained from specimens extracted at ¼ thickness, which suggests that a significant portion of the carbonitrides present in the core of the slab are eutectic and coarse, not having completely dissolved during the reheating of the specimens. This occurred despite the fact that the austenitization temperature adopted in this treatment theoretically leads to the total dissolution of Nb, as seems to have occurred in the case of specimens extracted at ¼ of thickness, where carbonitrides have a finer size.

Oct 1, 2019

By Tiago Rafael Ferreira de Brito

O presente trabalho comparou o desempenho do fosfato de zinco e do microfosfato de zinco, ambos com tecnologia dry-in-place para verificação do comportamento destes revestimentos frente à conformação mecânica, por meio do ensaio de embutimento Erichsen, método Nakazima e curvas limite de conformação (CLC). Foram estudadas chapas de aço-carbono grau EM e grau EEP G4 eletrozincadas e fosfatizadas. As chapas foram fosfatizadas empregando-se dois banhos: fosfato de zinco e microfosfato de zinco, ambos com tecnologia dry-in-place. A caracterização da morfologia dos fosfatos estudados por microscopia eletrônica de varredura mostrou que as camadas de fosfato de zinco não apresentaram formação de cristais, quando aplicadas por roll coater e as análises por EDS comprovaram a presença do elemento fósforo. O ensaio de embutimento Erichsen somado aos resultados obtidos nas curvas CLC demonstraram que o microfosfato exibiu desempenho melhor em comparação ao fosfato. A diferença entre os dois tipos de fosfato foi mensurável e evidenciou que a tecnologia dry-in-place colaborou com a produção de camadas fosfatizadas adequadas para a lubrificação durante o processo de conformação mecânica.

Aug 16, 2017

By Thiago Pinto Silva, Leandro Rocha Lemos, Luiz Fernando Andrade de Castro

This paper shows an evaluation about effect of dispersant sodium silicate along to limestone, in the form of pulp, on the cold agglomeration process for iron ore sintering. Before that, it was verified the effect of pH, solids content and amount of dispersant on the stability of the system (limestone, water and sodium silicate). It was found that the lower the solids content, the more alkaline pH and the amount of sodium silicate equal to 20 l for each 1t of limestone, was the level of dispersion of the system. The influence of the limestone pulp with dispersant depended on the granulometry of the ore mixture and the type of technological route. For the thinner type (42,8% <0.15mm), the limestone pulp with dispersant reduced the resistance of the adherent layer of the cold agglomerates, regardless of the technological route. However, for the coarser type (24,7% <0.15mm), the limestone pulp with dispersant increased the average size of the aggregates, preserving the resistance of the adherent layer when manufacturing with two intensive mixers in series.

Oct 1, 2019

By Ismar Antônio Sardinha

Usually outer straight steel tubes are used to blow supersonic oxygen into LD converters (BOF) to make liquid steel, although conical tubes are used too. Inner tube for oxygen blow and intermediary tube for water IN and water OUT are normally straight steel tubes. Present paper shows the influence of outer tube shape and metal used to in lance cooling and, consequently, a skull retention on lance surface. There are two parameters more important related to lance cooling: velocity of water out and the total lance cooling by addition of thermal conductivity of outer tube metal to it. For this comparison outer tubes are made of carbon steel or copper, and can be straight or conical. As related to velocity of water OUT, outer straight tubes have bigger efficiency than conical tubes. As related to total lance cooling, outer tube metal made of copper has much bigger efficiency than steel because of its thermal conductivity 7 to 12 times more depending on work temperature. The lance cooling has much bigger efficiency for the patented SKULLS3® technology with no skulls on the lance and no skulls into the mouth of LD converters (BOF).

Aug 17, 2017

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Fernando Generoso Neiva Ferreira

O aumento crescente dos requisitos de segurança a serem atingidos pela indústria automotiva vem cada vez mais exigindo a utilização de aços com maior conteúdo tecnológico, que é o caso do aço bifásico (“dual-phase”), que são caracterizados por uma microestrutura ferrítico-martensítica. Neste trabalho, estudaram-se, em escala laboratorial, os efeitos das temperaturas de encharque intercríticas (750, 800 e 850°C) e distintas taxas obtidas por dois diferentes meios de resfriamento (ar e ar forçado) na obtenção de microestrutura bifásica a partir de dois aços laminados a frio “full-hard” (produzidos industrialmente), com micro-adições de Nb e Mo e diferentes teores de C e Mn. Utilizando ensaios mecânicos de tração, microscopia óptica (MO) e eletrônica de varredura (MEV), observaram-se as influências da temperatura de encharque e da taxa de resfriamento sobre as microestruturas resultantes e as influências da presença de ferrita encruada, dos carbonetos não dissolvidos e da morfologia da segunda fase sobre as propriedades mecânicas das amostras estudadas.

Aug 16, 2017

By Eduardo Poltronieri Trés, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Anderson Denadai Thomzini

The first industrial applications of roller presses at the comminution were in 1984 in the cement industry. Since then, the equipment has taken more space in the mineral industry. However, many challenges are still present in this equipment, more specifically regarding to ore breakage predictability. The application of this equipment in the pellet feed preparation is fundamental to increase the surface area (blaine index) of the mineral using reduced energy consumption. However, even after several pressing steps, it is still challenging to achieve granulometry in percentages required for the pelletizing process. Currently these levels are reached in wet milling processes, typically carried out in wet ball mills. For the of pellets formation in pelletizing plants, both pelletizing and the firing processes requires finer granulometry. The motivation of this work is to study the pelletizing process, comparing the physical quality of the pellets produced only through comminuted ore in roller press the pellets produced in conventional comminution using circuit with ball mill.

Oct 1, 2019

By Luís Marcelo Marques Tavares, Gilvandro Bueno, Túlio MoreiraCampos

The HPGR development and application in the minerals industry resulted in an important increase in its application in iron ore pellet feed processing in the last decades. Vale SA was one of the pioneers in application of the HPGR in integrated plants, currently operating with six HPGRs in the pelletizing plants of Complexo de Tubarão (Vitória, ES). The work uses the mathematical model of the HPGR, proposed by Torres & Casali and modified by the present authors, to predict the performance of two industrial pellet feed HPGR units of the Complexo de Tubarão. Besides model validation, results of process simulations are shown in order to optimize the pellet feed pressing according to industrial demands, presenting different scenarios that are more attractive to HPGR operation. Simulations showed that it is feasible to reduce the specific surface area of the HPGR feed from 1770 cm²/g to 1570 cm²/g, allowing to produce a pellet feed of the same quality in its product (1911 cm²/g) and therefore reduce the work done by upstream ball milling.

Oct 1, 2019

By Bruno Pinheiro Silva, João José dos Santos Carvalho, Flávio Túlio Busatto, Leonardo Passos Perdigão

Sinter has high participation in the blast furnaces ferrous burden in ArcelorMittal Tubarão, being therefore of paramount importance the constant control of its physical, chemical and metallurgical qualities, aiming at the fulfillment of the client required quality. With the great challenges faced by market conditions, steelmaking companies seek operational sustainability, aiming at stability and reducing costs. One of the main steps to obtain these results in the Blast Furnaces is the raw materials quality stabilization, in order to guarantee the perfect burden distribution control and a better use of the reductant gas inside the reactor, aiming a lower fuels consumption. It is known that the smaller a ferrous particle is, better its reducibility, since a larger surface area provides greater contact with the reductant agent. Based on this concept, the objective of this work is to quantify the effect of the sinter size produced in ArcelorMittal Tubarão Sinter Plant in its reducibility, and in this way enable the definition of a better sinter particle size distribution aiming at a balance between the permeability effects and gaseous yield in the Blast Furnaces. In addition, the reducibility effects on sinter size reduction were evaluated, where the 5 to 10 mm fraction was analyzed in two sinter samples, the first obtained from the conventional route and the second after crushing of the fraction over 50 mm, in order to simulate the effect of the use of a Secondary Crusher in Sintering.

Oct 1, 2019

By Wolfgang Linden

The emerging demands on higher steel grades call for improvements in the operation of production units and a corresponding increase in automated processes, and therefore international steel producers require viable functions. The avoidance of slag carry-over to secondary metallurgy processes is essential for achieving steel grade qualities and reducing alloys in order to compensate slag residues in the downstream unit. The automatic tapping procedure in BOF converters will be supported by the implementation of reliable measurements used in high-end steel plants. Automatic tapping will help to achieve the following: Reduced slag carry-over, improved yield, increased reproducibility, improved working environment and safety and operation with minimum possible crew. The automatic tapping procedure is capable of being implemented in new or retrofitted installations.

Aug 17, 2017

By Andrea Zanon

Slitting processes have been used for many years to increase the productivity of smaller diameter deformed bars, without making major investments in the rolling mill. This technology is used mainly for the production of reinforcing bars (7-20 mm diameter), but successful applications exist also for round bar production. The multi-slitting process enables to produce up to 5 bars starting from one billet, thus increasing the productivity of the smaller products. Danieli Morgårdshammar, world leader in the supply of rolling mills for long products, has been a front-runner in slitting technology since its first applications and has recently developed, first in the world, the technology to produce 5X8mm rebar. This process has been recently applied in BRSM steel, a company based in Bangladesh which is a worldwide benchmark for slitting technology performances. This paper presents the necessary modifications which need to be considered when developing a 5-strand slitting project (and multi-strand slitting projects in general), as well as the results obtained at BSRM Steel when the process was implemented in 2016, the first rolling mill in the world rolling 5X8 mm slit rebars.

Oct 30, 2017

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Jörg Thomasberger

Delivering liquid steel to a steel processing unit at right temperature is an important criterion for high production steel shops, but it is surprising how little attention has been paid in the past to manage this vital phase in the steelmaking process-the steel in transit. The ladle running costs, both directly and indirectly, contribute significantly to the cost of steelmaking and should be an area of concern to any high production steel plant. Here we are talking not only of refractory costs or preheating fuel costs, but also cost of extra heating in ladle furnace, additional process delays incurred in delivering steel at right temperature to downstream unit in case proper care is not exercised at upstream unit, and occasional costs of ladle breakout due to inability to judge the residual life of the ladle. This paper emphasizes the need of a comprehensive ladle management system, an aspect which has not been properly addressed in the operations of a steel plant, in improving the productivity of a steel melt shop. Starting with review of present status and the attempts at implementation of ladle tracking in steel melt shop automation system, it looks at components of an exhaustive Ladle Management System (LMS), and finally gives an idea of benefits that will accrue from implementation of such a system in a steel melt shop.

Aug 17, 2017

By Lucas Monteiro Corrêa e Lopes, Carolina Carvalho Nunes, Nathalia Luiza Nascimento de Carvalho

The characteristics of each ore make it impossible to predict the quality of a flotation concentrate without exploratory tests. The research begins with laboratory batch tests, and then, after advances in the determination of process conditions, the complexity of the tests increases in order to evaluate new parameters. The closed cycle test (LCT) simulate circuits with load recirculation and the greatest difficulty of this test is to stabilize the circuit and achieve equilibrium. Depending on mass availability, the types of tests that offer the highest reliability and informations about flotation in an ongoing process are mini-scale or pilot-scale tests. This work aimed to compare the results of the flotation tests in three scales (batch test, LCT and mini pilot) for the Bonsucesso ore, a new deposit, owned by Nexa Resources, that has sphalerite, zinc ore, and galena, lead ore. In the open flotation circuit of galena was obtained 27.57% content with 26.70% recovery, in the LCT test the content was 31.54% with 64.64% recovery and in the mini pilot reached 51.22 % content with 65.51% recovery. In the open sphalerite flotation the zinc content was 55.51% with 77.35% recovery, in the LCT test the zinc content was 56.71% with 84.42% of recovery and in the mini pilot of 50.02% content with 94.54% recovery.

Oct 3, 2019