Search Documents

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Guilherme Corrêa Soares

Deeper understanding about the strain hardening behavior of steels has become necessary due to its importance in industrial processes such as mechanical cold forming, rolling and drawing. In this work, the strain hardening behavior of AISI 304, non-grain oriented electrical (NGO) and dual phase steels was investigated. Tensile tests were performed and the strain hardening behavior of each steel was studied by the Hollomon’s equation. X-ray diffraction measurements and hardness tests were also carried out in order to characterize the specimens. Different work hardening stages were observed in each steel during the deformation process. The results obtained are discussed in terms of the relationship among the instantaneous strain hardening coefficient, hardness and eventual phase transformations. The instantaneous strain hardening coefficient of dual phase and NGO increases after the yield point, rapidly reaching its maximum and then steadily decreases until tensile strength is reached. In AISI 304’s case, the strain hardening coefficient keeps raising to high values in response to a large strain and then rapidly decreases before reaching the tensile strength. In comparison to the other steels, AISI 304 shows higher instantaneous strain hardening coefficient value, which persists even in large strains. This is a consequence of its strain hardening mechanism based on stress-induced martensite transformation.

Aug 16, 2017

By Jaiza Bernardo de Oliveira, Iasmim Ariane Silva, Pedro Henrique Medeiros Câmara

The process of manufacturing pig iron in the blast furnace industrial units has the consequence of the generation of slag, a waste that can be produced in high quantity and present damages to the environment, when not reused. In the composition of this tailings, it is sometimes possible to find the presence of metals harmful to nature, such as manganese, which has an important and widespread utility in the metal industries, but still, the slag ends up not being used as a potential source of this element. Knowing this, the slags were subjected to crushing and grading steps to separate the aliquots. These were applied in the tests of technological characterization of the material, from MEV, EDS, Soxhlet and analysis of liberation degree by digital microscope, finding data of several analyzes. Having said that, the objective of this paper is to demonstrate, through the characterization of the slag, that this material has in its composition metallic elements, focusing on manganese, that can be reused in order to avoid the generation of environmental liabilities harmful to the environment. The results show a manganese content with a degree of release greater than 80% in bands from 48 #, which were divided by density and thus allow the gravimetric separation of the material in question.

Oct 3, 2019

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Gleison Vinicius Ricardo, Luiz Cláudio von Sperling Cotta, Artur Frederico Fonseca da Cruz, Evandro José de Castro Lopes

Binders are important raw materials in the iron ore pelletizing process. The bentonite, most usual, has been used in plants of this process since the forties due to its good performance in the agglomeration of ultrafine ore, although the silicon content in bentonite impairs the total iron content of the pellet, reducing its market value. This article studies the bentonite consumption reduction and improvement of the chemical quality of pellets by the addition of an organic binder in the productive process of Vale Vargem Grande pelletizing plant. By evaluation of variables as, drop test of green pellet, green pellet, dry pellet and fired pellet compressive strength tests, tumble index, percentage fraction of lower than 5 mm and total iron content in fired pellets, it was possible to approve the technical availability of the organic binder auxiliary in Vargem Grande pelletizing process. Nonetheless the positive influence of total iron content increase due to the reduction of bentonite consumption, it could also verify no impact on the physical quality of the pellets under the same production rhythm, approving once again the use of organic binders in pelletizing process.

Oct 1, 2019

By Marco Túlio Santiago Ferreira, Nilton Carlos Torquato, Washington Pirete da Silva

In 2005, with the significant reduction of iron content in the “Quadrilátero Ferrífero” reserves, Vale began the study of alternatives for the tailings disposal in other structures, that are not tailings dams. In 2011, after bench-scale and pilot-scale tests, it was defined to implement the project "Alternative methods for tailings disposal", including the construction of experimental drainage piles to get mineral and geotechnical process parameters for future projects. The result of this study shows that it is technically possible to replace traditional tailings disposal (dams), to dry stacking, with the proportion up to 20% of ultrafine tailings in the total tailings composition, however, this study is in evolution and the scale of the project / pile is being gradually increased to guarantee a good performance for the mineral and geotechnical process.

Oct 3, 2019

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Ismael Vemdrame Flores, Lindaura de Souza Cândido D’ Avila, Maurício Covcevich Bagatini, Arthur Felipe Lino Oliveira, Rafael Adriano Lopes Júnior

The use of pellet feed to adjust the chemical quality of the sinter is an alternative to the depletion of iron ore reserves. However, the addition of ultrafine in the sintering process can cause decrease of permeability and consequent drop in machine productivity. In this context, the present work investigated the addition of natural and ground pellet feed, evaluating its effects on cold agglomeration for sintering and quality of quasi-particles produced. Eight typical mixtures with industrial composition were produced in the laboratory, replacing Sinter Feed with different percentages of Natural Pellet Feed (NPF, 91% <150 μm) and Ground Pellet Feed (GPF, 83% <44 μm). The mixtures were subjected to cold agglomeration tests and the quasi-particles produced were evaluated by screening, shatter test, permeability test and disintegration into primary particles analysis. There was a decrease in the mean particle size of quasi-particles and reduce in permeability with addition of the ultrafines. The addition of NPF favored the layering mechanism in larger quasi-particles. The coalescence mechanism occurred for larger additions of NPF and GPF, being more expressive for GPF additions.

Oct 1, 2019

By José Francisco Cabello Russo, Késsius Bortolan Menezes, Henrique Dias Gatti Turrer, Denílson Rodrigues de Araújo

With the start-up of the Minas-Rio system, Anglo American, in Conceição do Mato Dentro, MG, in 2014, a methodology was also implemented and certified to perform the tests to obtain the results of TML (Transportable Moisture Limit). Such a parameter provides the maximum moisture content contained in the material that could be transported without the risk of the cargo liquefaction process, which could lead to incidents such as the tipping of ships carrying iron ore concentrate in bulk on the deep water. This means that when loading a ship, the moisture content of the material to be transported should not be higher than the TML reference value, obtained in a physical test and intrinsic to the material. Should this occur the charging may be rejected. From 2014 a downward trend was observed for this reference parameter in the Minas-Rio system, with results approaching the moisture of the filtered product, bringing risks to the operation of the project. In this way, an investigation of the possible causes for understanding this downward trend was required.

Oct 3, 2019

By Priscilla Pessin Coppo

The prevention of dental enamel wear has particular relevance for preventive and restorative purposes in dentistry. The wear damage can increase due to salivary disorders and/or parafunction (bruxism); antagonists incisal surfaces become flat and coincident. This study aims to investigate the wear behavior and the related mechanisms in sliding pairs of conformal incisal enamel, with similar values of hardness and fracture toughness, with different applied normal loads and lubricated conditions. Bovine incisors, under pin on flat configuration, were tested in two lubrication condition (dry or with natural saliva) and two applied normal loads (8 and 16 N). The worn surfaces were investigated by 3D profilometry and SEM. The analysis of worn surfaces indicated mechanisms of brittle fracture, but with different severities. Under a normal load of 16 N and dry condition, wear is controlled by a brittle process: microcracking with flake-like wear particles, which results in high friction coefficient (> 0.85), wear rate and wear volume. On the other hand, under a normal load of 8 N and natural saliva, wear took place in the interprismatic region, with consequent exposure of prisms and fracture in localized regions. In this case, the friction coefficient was 16% lower and the wear volume was one order of magnitude lower. Under 8 N and natural saliva, the wear was greater than in the dry condition, probably due to tribochemical reactions.

Jul 31, 2018

By Vera Lúcia Othéro de Brito

Literature has shown that spinel Co-Mn ferrite have potential application in magneto-mechanical sensors, due to its relatively high magnetoelastic sensitivity. In this work, Co-Mn ferrite was processed by means of the ceramic method, using Fe2O3, MnO and Co3O4 as raw materials. Samples were liquid-phase sintered, using Bi2O3 additive as liquid-phase former. X-ray fluorescence analysis was carried out in the raw materials in order to evaluate their impurity content. Atomic absorption spectrometry analysis was used for quantifying the Co/Mn/Fe proportion in the ferrite. The microstructure of the sintered sample was analyzed by means of Scanning Electron Microscopy. The magnetization and magnetostrictive behavior of the ferrite were evaluated, obtaining curves for magnetic hysteresis, magnetostriction and magnetoelastic sensitivity. The impurity inclusions and the Bi-rich particles formed from the liquid phase were characterized. The sintered ferrite had a total magnetostriction of -126ppm, which is lower than the values reported in literature for a Co-Mn ferrite of similar composition. It was verified that sintering was carried out within a critical temperature range, in which the decomposition of Mn ferrites may occur when sintering in air. This decomposition affects the magnetic properties of the material, and it may be avoided by using controlled sintering atmospheres.

Aug 8, 2018

By Jéssica Vicente Luiz, Rayander Martins Pimenta, Everton Pedroza dos Santos

The Hybrid Pelletized Sinter (HPS) is a agglomeration process that involves the combination of conventional sintering and pelletizing techniques and can be used with the purpose of obtaining improvements in the agglomeration stage of iron ore, and one of the great advantages of the process is the use of a wide particle size range of the ore. In this way, the superfines of low-cost ores, which are improper in sintering, can be used in the HPS process for the formation of the quasi-particle. The use of HPS with the sintering plants of the industries presented throughout the study, enabled an increase in productivity, decreased fuel utilization and reduced slag formation in blast furnaces. Thus, the present study aims to present a review of the literature on the Hybrid Pelletized Sinter (HPS) process and its main characteristics, as well as the results obtained by the companies that adopted the process.

Oct 1, 2019

By Beatriz Pereda, Ana Clara Fonseca da Silva, Tiago Seixas Bittencourt

Reinforcing steel bars are usually specified based on mechanical properties with flexibility in chemical composition and processing. Most developments, in these steels, are normally focused on alloy and process design to reach minimum cost and conformity to specification. Processing routes using quenching and self-tempering (QST) and accelerated cooling are the most common. Microalloying with V and Nb have been used in rebar. When acicular constituents must be avoided, a combination of Nb microalloying with judicious control of cooling is one of the preferred options. Niobium can contribute to improvement in tensile properties through austenitic grain size control during hot working, precipitation hardening due to carbonitrides or clusters, and hardenability increase. In the present work the alloy design and development processes of a Nb microalloyed steel for rebars are presented. The designed steel has fulfilled the required specification and is under regular production. Austenitic grain size refining – when comparing with the “basic composition” normally used was observed, even without any change in the thermomechanical processing cycle. There are indications that precipitation hardening may also occur. Results indicate that Nb is a good alternative as a microalloying element in rebars.

Oct 1, 2019

By Luis Henrique Torres Dantas, Maycon Athayde, Rossano Augusto Pilon Nunes

The objective of this work is to evaluate the physical quality achieved in the iron ore pellets and the temperature profile in the pellet bed by applying an inversion in the flow during the cooling. The firing of pellets requires a minimum residence time in the sintering temperatures of the hematite grains [1]. The applied concept aims at raising this time to pellets located at the bottom of the bed which would provide an improvement in the physical quality of the product. The tests were carried out in a pot-grate type oven and the samples of fired pellets were divided into three aliquots according to the loading position of the pot termed top, middle and bottom, the pellets were sieved and subjected to physical tests and the compared to conventional indurating flow with the same ores and inputs. It was possible to show an increase of 7 to 8% in the compressive strength of the medium and bottom layers, maintaining the top layer results. The objectives of the research were achieved and the tests will be extended to assess the impacts on the mass and energy balance of the indurating machine and its components.

Oct 1, 2019

By José Hamilton Resende Tavares, Késsius Bortolan Menezes, Mariana Vieira de Moura

Sampling and its representativeness is of significant importance in process control and decision making in the mineral sector. In this way, the present work seeks to compare different methodologies for the sampling of the iron ore from Anglo American. Through a sample of 120 kg, representing the industrial flotation circuit feed, samples obtained by the method of long pile, random sampling and rotary sample divider were analyzed, being the latter adopted by the company. In this case, after sampling, the material obtained through each method was subjected to the same sequence of characterization tests and the difference between the results statistically analyzed. Through such analysis it was observed that the random sampling method showed high values of variability and is therefore considered as unsatisfactory when compared to the other methods tested. In addition, rotary sample divider also showed parameters slightly superior to the long pile method. This study confirms the importance of appropriate sampling systems and procedures systems in the pursuit of reliable results.

Oct 3, 2019

By Leszek Maldzinski

The present concept assumes carrying out the process of controlled nitriding with NH3 alone. This is a simpler process than that using two-component mixes of ammonia diluted with N2 or NH3diss. The regulation of the chemical composition of the atmosphere in the retort, and therefore the regulation of the nitriding potential KN, is obtained through the variation of the inflow rate of NH3 into the retort. What is a completely new things in a relevant process, the inflow of NH3 into the furnace is at times reduced to zero, which widens the range of the gas composition in the retort (and by the same token, of KN). The amount of NH3 introduced into the furnace is regulated (controlled) with the aid of a gas analyzer (for example an infrared analyzer). The gas analyzer opens and closes periodically the NH3 inlet valve with a frequency maintaining a desired gas composition (a desired KN) in the retort. The concept was based on experimental and theoretical investigations in term of thermodynamic and kinetic of gas nitriding. Investigations were carried out in a laboratory furnace with a quartz tube and also in an industrial furnace with a steel retort and a circulating fan. Nitriding was performed using NH3, NH3+H2, NH3+NH3diss. mixtures. In an industrial furnace the supply of NH3 into the retort was periodically closed, though with an operating circulation fan. The studies demonstrated that the growth rate of nitrided layer depends only on the composition of the atmosphere, (or KN), in the retort. It depends neither on a type of atmosphere introduced into furnace (NH3, NH3+NH3diss. or NH3+H2) nor a type of furnace (laboratory with a quartz tube or industrial with steel retort and fan). The results proved also that entirely closing of NH3 supply to the retort does not affect the growth rate of nitrided layer. A detailed analyses of the results was performed in a paper.

Aug 16, 2017

By Shibu John

Rising energy demand and steadily decreasing quality of raw materials due to the global resource depletion are great challenges to the steel production today. The FINEX® Process has been developed jointly by POSCO, Korea and PRIMETALS Technologies Austria, to provide the iron making sector with the capability to lower hot metal production costs, environmental pollutions and to increase the flexibility in terms of operation and the choice of raw materials. FINEX® is a new technology combining a gas-based reduction in a series of fluidized bed reactors and a reduction smelting in a melter gasifier. Commenced in April 2007, the first 1.5Mtpa commercial plant has demonstrated the competiveness as an alternative iron making route. Another 2.0 Mtpa, third generation FINEX® (3G) plant was recently installed at POSCO, Pohang Works and has been operating satisfactorily since its blow-in in January 2014. Based on the well-proven plant concept, new process features, the highly competitive production costs and environmental advantages, the FINEX® Process can be considered as a competitive alternative to the conventional blast furnace iron making route.

Aug 17, 2017

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

In Potiguar West, in the regions of Vale do Açú, Mossoró, and Chapada do Apodi there are limestone outcrops of about 20 thousand square kilometers (with a thickness ranging from 50 to 400 meters). Limestone is an essential raw material for the manufacture of agricultural products and especially for construction. The rock serves for various productions, among them is used for the production of cement, lime, fertilizers, even ornamental rocks. Thus highlighting the mineral potential in the state of Rio Grande do Norte, as well as its use in the production of various products.

Oct 3, 2019