Search Documents

By Evan Thomas

It has been shown before that liquids can slip at a solid boundary, which prompted the idea that parallel-surface bearings can be obtained by the use of alternating slip and non-slip regions in the direction of fluid flow. The amount of slip at the wall depends upon the surface tension at the liquid - solid interface, which in turn depends on the chemical composition of the surface and its roughness. In the present study a heterogeneous surface was created by coating half of a circular glass disc with a coating repellent to glycerol. A rotating glass disc was placed at a known distance above the coated stationary surface and the gap was filled with glycerol. With the top surface moving in the direction of slip to non-slip region, a pressure build up can be theoretically predicted. The pressure gradient in the two regions is constant, similar to that in a Rayleigh step bearing, with the maximum pressure at the boundary. In order to accurately measure the force generated by the pressure increase, a load cell was attached to the heterogeneous disc. Experiments were conducted by varying both sliding speed and distance, and the resultant load carrying capacity was measured and compared with theoretical calculations. This allowed the slip coefficient of the coated surface to be evaluated.

Jul 31, 2018

By Jônatas Venancio Barbosa, Dagoberto Brandão Santos, Túlio Magno Füzessy de Melo

In this work, the mechanical and metallurgical behavior of titanium added ultra-low carbon (ULC-Ti) steel under hot and warm working conditions was studied by means of dilatometer compression tests. Double compression schedules were performed at temperatures between 700°C and 1000°C, inter-pass times of 0.5-100 s, and deformations of 0.5 and 0.3 in the first and second stages, respectively, with strain rate of 1 s-1. The analysis of the flow curves obtained allowed the evaluation of the softening characteristics of the steel. The softening and microstructure features indicate different restoration mechanisms depending on the temperature range. Static recrystallization with rapid microstructure restoration is observed at temperatures within the austenitic and intercritical field. Strain induced boundary motion and recovery mechanisms apparently control the restoration process in the ferrite region. In general, flow stress curves showed dynamic recovery behavior. Only the deformation in the intercritical region produced a peak in the flow stress curves. Isothermal holding tests associated with single hit compression indicated the presence of dynamic strain induced transformation, accelerating the softening kinetics at the intercritical region.

Oct 1, 2019

By Rudi César Comiotto Modena, Gabriel de Castro Moreira, Diego Machado Marques

The definition of geological/geostatistical domains is the first step in building a mineral resource model. A suitable division for these domains requires some prior knowledge about the deposit geology and can be supported by a careful statistical analysis. It is crucial that data with similar characteristics are grouped together, to avoid the mixing of statistical populations, defining the so-called stationary domains. In order to assist in this definition, two unsupervised clustering algorithms were applied: Otsu and K-means. The first one is widely used in image segmentation and it is based on the exhaustive search of the data to determine the best threshold for separating them. K-means is one of the most used techniques in machine learning, and it is based on the iterative analysis of the statistical distribution. Clustering algorithms may present some shortcomings when applied to geological data, since they are based on pure statistical analysis, not considering spatial distribution or data location. Choosing the most appropriate number of domains can also be challenging. Some methods for defining the best number of groups are presented, based on the analysis of variances between/inside groups, supported by indicators variography in order to verify this definition.

Oct 3, 2019

By Alessandro Molinari

In recent times, coke oven machines are acquiring a more prominent role in the coke making process. Apart from the traditional handling of the coal and coke flow, nowadays these machines are also deeply involved in all environmental and process control aspects. Paul Wurth coke oven machines have been developed by Schalke to meet the most recent requirements in terms of emissions control, automation, instrumentation, operability and maintainability. In CSP, Ceará, the new coke making plant represents the status of the art of the technologies applied to the whole coking process; starting from the Coke Oven Batteries and the Gas Treatment Plant developed by Paul Wurth up to the Coke Machines supplied by Schalker Eisenhütte, whose technology is now part of Paul Wurth coke making products portfolio. Present paper describes the plant configuration focusing on Coke Oven Machines and the key factors which are guarantying the success of the project.

Aug 16, 2017

By Márcio Corrêa de Carvalho

Welded deposited chromium carbide overlay’s has been widely used in various branches of welding overlay’s industry related to wear. Characterization techniques are an important tool in the development of chromium carbide overlays resistant to wear, enabling the identification of phases, constituents and defects. In this work one used optical microscopy, scanning electron microscopy and energy dispersive spectroscopy on chromium carbide overlay’s deposited by submerged arc welding process. The characterization techniques identified precisely the elements of the overlay’s enabling point of the main cause of the observed defects such as cracks, porosity and clusters of particles known in the industry as " rice crispy" .

Aug 16, 2017

By Ernesto Furtado de Mello Neto, Eliezer Thuler, Claudio Vano Nunes, Carlos Alberto Cristofari

The Brazilian steel industry is dealing an adverse scenario with direct competition from global emerging markets. In this scenario, the need to improve asset operational performance, makes complex studies involving technical knowledge and asset life behavior, become important tools to support companies strategic accomplish. These studies allow consider performance, costs and operational risks relationship in the decision make process. The Asset Management approach support these studies in order to observe the whole asset life cycle, understand value chain through all company process and optimize the asset economic life. In this context, the present technical work has the purpose to support asset management decision making regarding ArcelorMittal Vega cold rolling drive motors, through the motors fail behavior modelling and estimated the risks involved in asset management decision. Through the Reliability, Availability and Mantenability (RAM) analysis, simulations were performed considering the failure, repair cost data and investments to build options to mitigate the operational risks.

Oct 9, 2019

By Enif Gutiérrez Guerrero

Inclusion deposition is still a standing problem in the continuous casting of steel since the deposition of alumina inclusions inside the SEN affects the productivity and the product quality. The present work studies the factors involved in the inclusion deposition at the nozzle and the effects of inertial, gravitational, buoyant, pressure gradient, and Saffman forces on the inclusion trajectories. The results show that the inclusions reaching the nozzle, only 30% get deposited along its walls mainly at the Upper Tundish Nozzle (UTN). This area of higher deposition is identified close to a low static pressure and a high turbulent kinetic energy dissipation zones where the effects of the gravitational and buoyant forces do not promote a significant inclusion radial movement since these are aligned with the direction of the flow stream lines. In contrast, in this zone, the Saffman force shows an important effect on the deposited inclusions, slowing down the inclusions in the vertical axis and increasing their radial movement.

Aug 17, 2017

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Paulo de Tarso Rossi Haddad, Eric Valmir Spósito, Cristiane Sales Gonçalves

The heat treatment is a process that acts as a key factor in the tool life of tools made with hot work tool steels. Due to their applications, the main desirable metallurgical properties of this material class are toughness and hot resistance, without which the tools may suffer premature failure, and may lead to increases in the cost of producing articles made using such tools [1, 2]. Therefore, special attention must be given to the heat treatments practiced in these steels, whose operations involve quenching and tempering. The present work carried out the effects of the austenitizing and tempering temperatures on the microstructural condition, hardness and impact properties of TENAX300IM®, modified AISI H11 with lower silicon content. Hardness was measured by the Rockwell method, C scale; the toughness was evaluated by the Charpy-V impact test; and the microstructure for each condition was evaluated by optic microscopy. It was shown that higher austenitization temperatures resulted in increased grain size and hardness; higher tempering temperatures resulted in reduction of hardness, and secondary hardening peaks were observed for some austenitization conditions. The impact resistance showed an inverse behavior to that of the hardness, remaining initially constant, up to ~ 550 ° C of tempering temperature, and then increasing with the tempering temperature. The microstructures presented great dissimilarity, mainly due to the dissolution of carbon and alloying elements in the matrix.

Nov 22, 2018

By Walter Luiz Castro dos Santos, Leandro Resinentti Zanon

In the production of iron ore pellets, one of the factors that strongly influence the cost of ore-pellet processing is the specific consumption of natural gas that occurs during the thermal processing stage of the pellets. The filtration process is the step where the adequacy of the moisture percentage of the retained pulp occurs, so that subsequently there is the processing in the subsequent stages of the pellet formation and hardening of pellets. The water contained in the raw pellet is withdrawn at the stage of thermal processing. For this purpose, the literature indicates the demand of 600 Kcal/kg of water for the heating and vaporization of the moisture of raw pellets. The statistical analysis of the performance data of a pelletizing plant showed that for each decrement of 0.1% of water in the retained pulp is equivalent to the reduction of 0.091 Nm3 in the consumption of natural gas per tonne of pellets produced. Thus, the proper performance of the filtration stage is essential to reduce the percentage of pulp moisture retained and consequently to increase the energy efficiency of the pelletizing furnaces. The aim of this article is to present the main steps in conducting a work to increase the filtration performance to reduce the percentage of retained pulp moisture and the positive impacts on the specific natural gas consumption of a plant Pelletizing.

Oct 1, 2019

By Bruce V. Kiefer

A modernization project was undertaken by Kroman Celik Sanayii A.S. in order to improve their product quality, consistency and shape of the coil package, reduce maintenance and delays in rod mill, thereby increasing utilization and productivity. The project involved installation of a new Morgan Intelligent Pinch Roll and High Speed Laying Head, modifications to the existing controlled cooling conveyor, plus replacing the coil reforming station. The new pinch roll and laying head were to provide better control of the ring formation and consistency of the coil on the conveyor, while reducing delays on the conveyor. Changes to the controlled cooling conveyor included installation of new nozzle decks and Optimesh air distribution system along with re-arrangement of existing fans in order to improve both cooling rates and uniformity of cooling. This paper explains details and features of the newly-installed equipment technology. Resulting product and process improvements are presented, including increased tensile strength and uniformity, reduction in delays on the conveyor and reform tub, plus improvements in coil quality.

Oct 30, 2017

By Ryoma Fujiyoshi

In this article, the technologies of highly durable MgO-C bricks for the scrap impact zone and bottom blowing tuyere of converters are demonstrated. On the bases of our recent investigations, wear of scrap impact zone and bottom tuyere are explainable in terms of crack initiation and propagation. Theoretically, crack propagation in brittle material is regarded as generation of new crack surface area. It occurs when the elastic strain energy stored in the material exceeds the energy required to generate a new crack surface area. Since the overall energy consumed for crack propagation until fracture is evaluated by fracture energy, materials exhibiting high fracture energy can be regarded as materials with high fracture resistance. Therefore, two fracture energy-improving technologies for MgO-C bricks were developed. One is matrix reinforcement and the other is carbon bond enhancement. These technologies were applied to bricks for the scrap impact zone and bottom tuyere. As a result of commercial applications, notable decreases in wear rates were recognized for high fracture energy materials for the scrap impact zone and bottom blowing tuyere of converters.

Oct 30, 2017

By Alberto Tremea

The eddy current system is universally recognized as a most suitable method to point out discontinuities or modifications on the roll surface. The automation of the controls through the implementation of sophisticated equipments on the grinding machine has favoured its employment in the roll shop. A big effort is still going on to clarify the best way to promptly identify situations that could be really unsafe for the roll life. The results presented in this paper have been obtained through an intensive activity conducted in field by Innse Cilindri on work rolls of finishing stands of hot strip mills. The correct interpretation of the eddy current signals and a good calibration of the automatic system have allowed, in many cases, a substantial optimisation of regrinding practices.

Aug 16, 2017

By Keulla Venya Urbano e Silva, Marcelo Quintão e Silva Marchetti, Rafael Silva Marcelino, Rafaella Bicalho da Rocha

Comparative study between standard and BigFLUX matrices for high intensity magnetic separation pre-concentration (WHIMS) stage for iron ore. The evaluation was carried out on GAUSTEC’s pilot equipment for samples from Viga Mine’s operation. Samples in different feed iron content on rougher stage were evaluated in 46 experiments with matrix variation. The analisys compared chemistry, mass recovery and metallurgical recovery results to define the most efficient matrix to use in a pre-concentration stage.

Oct 3, 2019

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019

By Alim Ullah

The paper discusses the necessity of upgrading low-iron containing ores, giving as an example, NML-Tata Steel Project in the Quebec-Labrador region of Canada. As cooling of pellets is generally a bottle-neck in most pelletizing plants, examples are given of the methods used to improve cooling in the existing plants and a simple, low-cost alternative, tested on a pot-grate system, is presented. The procedure described is applicable to sinter plants also. The trends in iron and steel production worldwide are then given, as well as the reasons for the increase in steel production by the Electric Arc Furnace (EAF) route. The stoichiometric and thermodynamic requirements for producing iron, irrespective of the process, are explained. The different ironmaking processes, especially the Direct Reduction (DR) ones are briefly discussed, outlining recent improvements made to some of them. The pros and cons of producing cooled DRI and Hot-Briquetted Iron (HBI) are given with predictions made for their future growth. An alternative to cold-briquetting of DRI fines is also discussed. Highlights of an ironmaking processes which is at the laboratory/pilot plant stage are given.

Aug 1, 2018

By Miguel Araújo Vasconcelos Filho, Ulisses Tetti

In order to determine the influence of the number of increments of the sinter sample on the variability of the chemical composition obtained in Sinter Plant production, a variographic study was carried out. It was performed with two series of samples. The first series was composed of 40 samples with a 6-second interval, with the objective of obtaining the so-called minimum practical error, resulting from the extraction processes of the sample of the conveyor belt and preparation and analysis in the laboratory and the second series composed of 60 samples with a range of 4 minutes, which points to the sample selection error. The results obtained showed that the minimization of the sample selection error occurs for increments spaced in 15 minutes, being in agreement with ISO 3082, but with significantly better results than those currently practiced for intervals between 1hour increments. It was then decided on the suitability of the sampler to allow hourly increments to be collected and on a second opportunity to install a sampling tower with primary and secondary samplers to collect increments every 15 minutes including sample size reduction.

Oct 1, 2019