Search Documents

By Luiz Bruno de Oliveira Araujo, Luciano Morais Teixeira, Luiz Gustavo Pedrosa de Melo, Altair Lúcio de Souza

The off-line simulation of the metallurgical process in an industrial line brings several benefits such as: evaluation of the influence of the main parameters that affect the results of the process, comparison between different set ups, greater assertiveness in operational adjustments, process optimization and reduction tests for development of new products. With this objective, a software for offline simulation of the hot strip mill process of Gerdau Ouro Branco was developed based on the logic of calculations implemented in the online model. The software results in important process variables such as mill pass scale, load, torque, and power at each pass, temperature and the hot mean flow stress of the simulated material. During rolling mill process the strip presents different temperatures and time between passes for different points along the length, which directly influences the hot strength of the product and consequently in the calculated variables, thus the calculations executed by the software were divided to three points of the strip, head, body and tail bringing the individual results to each of these positions.

Oct 1, 2019

By Wolfgang Linden

One of the most important factors in successful electric steelmaking is the continuous observation of the process and the reaction to it. Traditional electric arc furnace control uses mainly direct controls which are based on the electric power input. Not considering the furnace conditions will necessarily lead to suboptimal operation in terms of energy consumption and productivity not fully utilized.The ARCCESS FEOS (Furnace Energy Optimization System) includes the simultaneous control of the transformer tap, impedance operating point, reactor tap, burner and carbon injection, and DRI charging control. FEOS has proven in practical operation benefits of high melting yields, no interruptions through switch offs in borderline temperature area, rapid reaction, reproducible and efficient electrical energy input and short power-on times.

Jul 30, 2018

By Junio Simões Pereira, Carlos Magno Nascimento, Frederic Yann Armache Braga, Luiz Cláudio Monteiro Montenegro

Given the current scenario experienced by Brazilian mining industry, the study and development of technologies that enable a more secure and controlled disposal of tailings has gained significant relevance. Among the various alternatives and disposal methodologies, Anglo American has been developing tests on three study fronts: dewatering polymers, hydrocyclone dewatering and pulp filtration. The first two fronts are intended to optimize the way of occupying the existing tailings dam. The filtering is intended to reduce the mass transfer to the reservoir, extending the life time of the existing structure. The studies were divided into laboratory, pilot and industrial phases, aiming at proving applicability and scheduling for a definitive future installation. Until this moment, all tests have demonstrated gains and potentials of applicability.

Oct 3, 2019

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By José Francisco Cabello Russo, Késsius Bortolan Menezes, Henrique Dias Gatti Turrer, Denílson Rodrigues de Araújo

With the start-up of the Minas-Rio system, Anglo American, in Conceição do Mato Dentro, MG, in 2014, a methodology was also implemented and certified to perform the tests to obtain the results of TML (Transportable Moisture Limit). Such a parameter provides the maximum moisture content contained in the material that could be transported without the risk of the cargo liquefaction process, which could lead to incidents such as the tipping of ships carrying iron ore concentrate in bulk on the deep water. This means that when loading a ship, the moisture content of the material to be transported should not be higher than the TML reference value, obtained in a physical test and intrinsic to the material. Should this occur the charging may be rejected. From 2014 a downward trend was observed for this reference parameter in the Minas-Rio system, with results approaching the moisture of the filtered product, bringing risks to the operation of the project. In this way, an investigation of the possible causes for understanding this downward trend was required.

Oct 3, 2019

By Liao Jianfeng

The Baosteel Zhanjiang 5,050m3 blast furnaces have been built with highly independent integration and innovation technologies and represented the state of the art of the world’s huge BFs. The proper of BF1 and BF2 is designed with long-campaign technology; both BFs share the same set of stockhouse, water and PCI systems; the BCQS serial-hopper no-bell top, TRT and blower are all local equipment as applied; four top-combustion stoves systems are matched; the BFG is cleaned by fully dry process; and the automation control system for the main process is self integrated. The BFs have been started up and performing with sound indicators. Their smooth proceedings symbolize China’s huge blast furnace ironmaking technology ascending a new high.

Oct 30, 2017

By Alessandra Spaghetti

Rolling small-diameter hot wire rods at high speeds with conventional laying head pipes can wear the pipe out frequently and affect quality and consistency in the final product. Laying head upgrades using Sandvik SAF2507LHP™ (UNS S32750) tubes make possible to achieve optimal metallurgical properties, smooth coil formation and easier coil handling. Operators can also avoid unwelcome shutdowns due to frequent worn pipe changes and turndowns. Sandvik have been developing different customers and understand their process needs. The suitable selection materials that are able to withstand high levels of wear better than low alloy and carbon steel grades that are commonly used in industry is very important to improve the quality and increase productivity. UNS S32750 tubes were demonstrably superior to low alloy and carbon steels when used in Laying Head Pipe system regarding tubes lifetime, reducing replacement, production interruptions and increasing reliability.

Aug 17, 2017

By Vitor Vianna de Castro Moreira, Danilson Gonçalves de Melo e Silva, Gabriel Augusto da Fonseca

The present work aims to describe the changes made in the operational procedure of the reheating shell furnace, of the hot-rolling of seamless tubes line at Barreiro Plant of VSB, during non-production periods, focusing on reducing natural gas consumption. According to the previous procedure, the furnace was kept at 750°C on these periods, using the main burners. With the new procedure, the furnace is naturally cooled, maintaining only the auxiliary burners with a pilot light turned on, without worrying about the conservation of temperature. Subsequently, the furnace is heated with a rate of 150 ºC/h until it reaches the setpoint temperature of production. This procedure change was successful and didn’t cause operational and security problems. The minimum stoppage time needed for the natural cooling to be economically favorable is 6 hours and 30 minutes. The new procedure reduced the natural gas consumption in 4.500 Nm³, considering 24 hours of stoppage, achieving an estimated annual economy on the thermal energy costs of R$440.000,00 in 2019.

Oct 3, 2019

By Lesli Peterson

Spraying Systems Co® has continued to develop and evolve descale nozzles through the years. The most recent addition to the descale nozzle line, the DescaleJet® Pro, provides more impact and a more uniform distribution than previous descale nozzles. The improved performance has been achieved through multiple design changes such as a smoother approach, updated vane design and improved carbide orifice. In addition to providing improved spray performance the nozzle also lasts longer than previous versions. The new technology has been thoroughly tested in the lab using impact measurements and accelerated wear testing. In addition to lab testing the nozzle has provided improved performance and longer wear life for those that have made the change to the new technology. The new nozzle technology and the benefits to the rolling mill will be discussed.

Jul 30, 2018

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By José Ricardo Nunes de Macedor

Com o crescente zelo ambiental, os polímeros biodegradáveis ganharam importante papel no mercado mundial. Em especial, o amido é um destaque por apresentar preço baixo e alta demanda, contudo possui grande fragilidade mecânica e os seus filmes são muitos hidrofílicos. Outro importante polímero biodegradável é o poli(ácido lático) que possui, alta resistência mecânica e transparência, quando comparado com o amido termoplástico, permitindo sua aplicação em embalagens alimentícias. Contudo, o PLA ainda possui custo elevado, quando comparado ao amido e até commodities, como o PET, PP e PE. Estudos com algodão, material em grande produção e baixo custo, retratam ganhos nas propriedades mecânicas sem perda da biodegradabilidade em compósitos. Assim, este trabalho objetivou preparar, por meio de homogeneizador termocinético KMixer e prensa térmica, placas de compósitos de PLA contendo amido (0, 3 e 5% m/m) e fibras de algodão in natura processadas (0, 10 e 20% m/m). As amostras foram caracterizados por espectroscopia na região do infravermelho com transformada de Fourier (FTIR), ângulo de contato estático e ensaios mecânicos (módulo de Young, resistência à tração e alongamento na ruptura). As análises mostraram que a adição de fibra de algodão compensa a perda de resistencia à tração ocasionada pela adição de TPS. Tanto a fibra como o amido aumentaram a molhabilidade do compósito.

Aug 8, 2018

By Wellington Ribeiro Moreirar, Anderson Willian Henrique Santini, Lívia Mara Cândido, Adriano Raimundo Totour

Rejects generated in mining projects usually do not have associated economic value. Most of the ore beneficiation processes occur by wet process with a higher fraction of water and ultrafine granulometry, which makes it difficult to dispose of these wastes. In 2013, studies with new tailings treatment and filtering technologies were initiated with the objective of eliminating the disposal of the residue generated in the industrial process to wet in dams. In this context, we tried to evaluate an alternative for the dewatering of the sludge and the tailings, aiming at their disposal in piles. Essentially, we sought to consolidate the application of the high-pressure filtration technology for the effluent dewatering, in order to allow its transport and its disposal in a sustainable way. The studies performed in a pilot filter showed good performance and allowed the industrial implantation. The studies and geotechnical indications of composite tailings (flotation and sludge) make it possible to dispose of the tailings in piles due to their better values of humidity, which allows them to be safely stacked.

Oct 3, 2019

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019

By Lucia Vieira

Kelvin probe force microscopy (KPFM) can be used to monitor electrostatic charges on the surfaces of materials. In this paper, we describe the use of KPFM to evaluate the electrostatic effect induced by silver nanoparticles incorporated as clusters in diamond-like carbon (DLC) films, before and after scratching. The results are compared to those obtained for DLC films without silver nanoparticles. Raman spectroscopy was used to identify the DLC signature, and energy dispersive X-ray spectroscopy (EDX) was used to confirm the presence of silver in the film. The morphology of the DLC film containing silver was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings suggest that the incorporation of silver nanoparticles in amorphous materials could offer new options for electrostatic energy storage on the surfaces of these materials.

Jul 31, 2018

By Christiano Gianesi Bastos Andrade

Clays with high content of smectite are denominated bentonites, and are widely used in industry as, for example, agents for bleaching of vegetable oils, animals and minerals. For this use, the smectite clays are treated with inorganic acid of high concentration at temperatures under boiling point, which provide the bentonite´s bleaching power. In the present study, a sample of smectite from Cubati, Paraiba, Brazil, was submitted to treatment under moderate conditions (90°C, reaction times of 1, 6, 12, 18 and 24hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, acid solution/clay ratio of 1g/10mL), aiming to reduce impurities, responsible for the color of the clay, without causing significant changes in their structure. Thus, clay can be used in the cosmetics industry and other products with high added value. The treated clay was characterized by scanning electron microscopy (SEM), stereomicroscopy, energy dispersive X-ray detector (EDS) and X-ray diffraction (XRD). It was observed a bleaching in samples with time of 12h to 18h. With the DRX was possible to monitor the peak intensity of the clay structure and the sample with 12 hours of treatment was not significantly altered its crystalline structure, maintaining the peak clay at d001. The most pronounced changes in the bleaching occurred within the first 12 hours of acid treatment.

Aug 8, 2018

By Fernando Generoso Neiva Ferreira

O aumento crescente dos requisitos de segurança a serem atingidos pela indústria automotiva vem cada vez mais exigindo a utilização de aços com maior conteúdo tecnológico, que é o caso do aço bifásico (“dual-phase”), que são caracterizados por uma microestrutura ferrítico-martensítica. Neste trabalho, estudaram-se, em escala laboratorial, os efeitos das temperaturas de encharque intercríticas (750, 800 e 850°C) e distintas taxas obtidas por dois diferentes meios de resfriamento (ar e ar forçado) na obtenção de microestrutura bifásica a partir de dois aços laminados a frio “full-hard” (produzidos industrialmente), com micro-adições de Nb e Mo e diferentes teores de C e Mn. Utilizando ensaios mecânicos de tração, microscopia óptica (MO) e eletrônica de varredura (MEV), observaram-se as influências da temperatura de encharque e da taxa de resfriamento sobre as microestruturas resultantes e as influências da presença de ferrita encruada, dos carbonetos não dissolvidos e da morfologia da segunda fase sobre as propriedades mecânicas das amostras estudadas.

Aug 16, 2017

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By Geovane Viturino da Silva, Jeziel de Melo Canedo, André Wulff Hirano, Maxwell Pereira Cangani, Luiz Henrique Curado Ribeiro

With the deterioration of the quality of the iron ore, the new conditions of quality of the raw materials (mainly sinter feed) were adapted to their processes, resulting in the need for changes in the chemical quality of the sinter for blast furnaces in the Ternium Brazil, without changing the parameters of chemical, physical and metallurgical quality. Due to the change in this scenario, there was a great impact on the quality of the fine iron ore this year in 2019, due to which the work ranges of sinter MgO and B2 were currently modified to minimize these impacts in the blast furnaces of Ternium Brazil. This work aims to minimize the effects of the sinter worsening, with the reduction of the sinter MgO and B2 bands, with an increase of 2% in the mixture yield and FeT elevation in the range of 1.6% in the sinter product.

Oct 1, 2019