Search Documents

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By N. Mungan

Formation damage, i.e.. reduclion in permeability, has been generally attribuled to clay minerals which expand or disperse upon contact with water that is less saline than the connate water. Luboratory, studies show that penneahility reduction can also occur in formalions containing only nonexpandable clays such as illite or kaolinite, and can be caused also by changes in pH. Furthermore, pH changes can damage even formations that are essentially free of clays. It is suggested that permeability reduction is due to the small passages being blocked by particles, which may be dispersed clays, cemenlion material or other fine parricles. These particles are dislodged by dispersion of clays due to changes in salinity or by dissolution of calcareous cement by acids, or of silicaceous cement by alkaline solutions. In working with reservoir cores, it was found that extracted cores damaged more easily and extensively than nonextracted cores. The extent of damage depended also on tenlperatltre. INTRODUCTION Permeability is an important property of porous media and has been the subject of many studies by engineers and geologists. Many of these studies are conccrned with formation damage, i.e., reduction in permeability, resulting from exposure of oil-producing formations to water substantially less saline than the connate water. This effect causes understandable concern since during drilling, completion and production phases formations are often exposed to fresh water. The damage resulting from contact with relatively fresh water has been attributed to expansion and dispersion oF clay minerals. During laboratory investigation of the use of NaOH as a wettability reversal agent to increase oil recovery from oil-wet reservoirs, several cores used in the displacement studies suffered loss in permeability. Despite the traditional usage of NaOH for conditioning aqueous mud systems, the role of the caustic filtrate in wellbore damage seems to have been overlooked. Browning2 as recently reported on the effects of NaOH in dispersing clay minerals but he was concerned only with complications that may arise in drilling massive shale beds. The following study was made to examine the role of pH and salinity changes in core damage. Where cores from reservoirs were used, tests were performed with extracted and nonextracted cores both at room and reser- voir temperatures, since it was felt that the test environment and core condition may affect the results. Because of its limited coverage and exploratory nature, this study is not intended to provide answers to field formation damage problems. It is hoped that it will encourage research into new aspects of the permeability reduction problems, particularly those allied to new recovery and production processes. PROCEDURE In all permeability tests, fluids were pumped through the cores at a constant volumetric rate. Only deaerated fluids and reagent grade chemicals were used. The fluids were passed through two ultrafine filters before injection to remove any entrained particles. The cores, with the exception of the unconsolidated cores, were mounted in Hassler holders. Water was used to transmit pressure to the sleeve. The inlet endpiece had two entry ports which permitted scavenging one fluid with another to avoid any mixing in the small holdup volume. The cores were flushed with CO2 gas, evacuated for 5 to 6 hours and saturated with the first liquid at a pressure of 1,000 psi for 24 hours to eliminate any free gas from the cores. Pressure differences up to 20 psi were measured by transducers, calibrated in inches of water and continuously recorded. For greater pressure drops, gauges were used. All reservoir cores were cleaned with a light refined mineral oil, then with heptane, and finally dried with CO2. Compatibility tests showed that no precipitates formed when mineral oil and the crudes were mixed. Some cores were extracted in Dean-Stark-type solvent extractors using xylene and trichloroethane and dried in a vacuum oven at 450F. Each test consisted of a sequence of water, test solution, and again water flow. RESULTS AND DISCUSSION STUDIES IN BEREA CORES Salinity Contrast Berea cores 2-in. in diameter and 12-in. long were cut from sandstone quarried in Cleveland, Ohio. The clay minerals were identified by X-ray diffraction to be chlorite, kaolinite, illite and incerlayered illite. Flow of fresh water or 30,000 ppm brinc does not cause any permeability reduction (Fig. 1). However, after injection of brine the core is readily damaged by fresh water. Damage starts almost instantly as the fresh water injection is begun, and at a cumulative injection of 1.2 PV fresh water, the permeability has dropped from 190 to 0.9 md. Upon continued injection, the effluent contains clay minerals dislodged from the core. The final core per-

Jan 1, 1966

By S. G. Gibbs

A new method for predicting the behavior of sucker-rod pumping systems is presented. The pumping system is described by a flexible mathematical model which is solved by means of partial diflerence equations with the aid of computers. Polished rod and intermediate-depth dynamometer cards can be calculated for various bottom-hole pump conditions. The technique permits simulation of a wide variety of operating conditions, both normal and abnormal. The data generated with the new technique are useful in refining the criteria for design and operation of sucker-rod systms. INTRODUCTION Sucker-rod pumping systems are used in approximately 90 per cent of artificially lifted wells. In view of this wide application, it behooves the industry to have a fundamental understanding of the sucker-rod pumping process. Oddly enough, our understanding has been rather superficial. This is evidenced by the semi-empirical formulas which have been used as the basis for design and operation of sucker-rod installations. Thoueh- we have realized the limitations of our methods for many years, it has not been computationally feasible to use more refined techniques. With the advent and widespread use of digital computers, it is now possible to handle the mathematical problems associated with sucker-rod pumping. This paper summarizes a computer-oriented method which can provide greater insight into the sucker-rod pumping process. It is hoped that this technique, and techniques which may evolve from it, will prove to be the tool needed by industry to obtain the most efficient use of rod pumping equipment. THE MATHEMATICAL MODEL Prediction of sucker-rod system behavior involves the solution of a boundary value problem. Such a problem includes a differential equation and a set of boundary conditions. For the sucker-rod problem, the wave equation is used, together with boundary conditions which describe the initial stress and velocity of the sucker rods, the motion of the polished rod and the operation of the down-hole pump. Of these items, the wave equation, the polished rod motion condition and the down-hole pump conditions are of primary importance. Discussion of the mathematical model centers about these factors. ROD STRING SIMULATION WITH THE WAVE EQUATION The one-dimensional wave equation with viscous damp- is used in the sucker-rod boundary value problem to simulate the behavior of the rod string. This equation describes the longitudinal vibrations in a long slender rod and, hence, is ideal for the sucker-rod application. Its use incorporates into the mathematical model the phenomenon of force wave reflection, which is an important characteristic of real systems. The viscous damping effect postulated in Eq. 1 yields good solutions, even though nonviscous effects such as coulcomb friction and hysteresis loss in the rod material are present. Fortunately, the nonviscous effects are relatively small, so the viscous damping approximation used in the wave equation is adequate. The coefficient v is a dimensionless damping factor which is found in field measurements to vary over fairly narrow limits. For mathematical convenience the gravity term is omitted in Eq. 1. The effect of gravity on rod load and stretch can be treated separately, as will be noted later. Since Eq. 1 is linear, the legitimacy of this procedure is easy to demonstrate. POLlSHED ROD MOTION SIMULATION The motion of the polished rod is determined by the geometry of the surface pumping unit and the torque-speed characteristics of its prime mover. By determining the motion of the polished rod, we formulate an important boundary condition. From trigonometrical considerations it can be shown that the position of the polished rod vs crank angle 0 is given by (see Fig. 1) These equations are obtained from the general solution of the "four-bar" linkage problem and can be used to describe the kinematics of any modern beam pumping unit.' If prime mover speed variations are disregarded, the angular velocity of the crank is constant, and Eq. 2 can be used to predict the position of the polished rod vs time. However, the constant-speed condition leading to constant crank angular velocity is only approached in practice: hence, it is better to make provisions for prime mover speed variations in the mathematical model. The speed at which the prime mover runs is determined by its torque-speed characteristics and the torque imposed upon it. The torque that the prime mover "feels" is the net torque arising from the polished rod load and the opposing torque from the counterbalance effect. The

By K. H. Ribe

Water often enters an oil reservoir during completion or workover operations on a well and forms a partial "water block" to oil production. A mathematical study of radial two-phase flow, neglecting capillary effects, has been employed to study the formation of such a water block and subsequent re-moval by production from the well. The effects of reduced oil permeability about the well on the well productivity were studied. The fluid saturation distributions about the well during formation and removal of the water block have also been computed. Several relative permeability relations and viscosity ratios were employed. If water has invaded the formation, its influence through relative permeability effects alone can cause the following. 1. Oil productivity will be depressed for extended periods after production is resumed and will build up only gradually as the water is removed. 2. Oil injected for treatment of water blocking will delay rather than promote restoration of full well productivity by enlarging the region invaded by water. Thus, unless the specific action of chemicals contained in the oil is needed, oil injection appears undesirable. INTRODUCTION During oilwell workover operations, water may enter the oil-bearing formation from the wellbore. When production is resumed, oil must flow through the region invaded by this water. The presence of this region can cause both well productivity and oil production rate to be low and oil to be produced with high water-oil ratio for some time after production is initiated. This situation is sometimes described as a water block. The introduction of water into the formation may result in other actions which also lead to reduction in well productivity and which are also usually included in the connotation of the broad term, water block. Often considered, for example, are the possibilities of clay swelling by contact with fresh water and the formation of emulsions with the formation oil. If it is suspected that such specific actions have taken place, remedial treatments are undertaken which usually involve the injection of chemicals in oil. Since the introduction of water, even in the absence of specific interactions with the formation or oil, will cause a temporary water block (which might be misinterpreted as evidence of a more severe situation), it is of importance to evaluate the magnitude and duration of this blocking which results purely from the reduction in relative permeability to oil in the vicinity of the wellbore. It is also of interest to evaluate the effect of oil injection on the productivity of a well blocked by water in this manner. Inasmuch as this unfavorable condition may persist for some time, it may lead to premature condemnation of a workover or premature abandonment of a potentially productive pay zone. A quantitative evaluation of the influence of water entry on the oil productivity through changes in relative permeability was made by solving a radial form of the Buckley-Leverett equation. The distribution of water saturation around the wellbore during the entry of water was calculated and was followed by a similar calculation of the saturation distribution during the period of resuming production. At any stage in the removal of the invading water, knowledge of the distribution of its saturation permitted calculating the attendant loss in oil productivity. The influence of the shape of the relative permeability relationships was also evaluated by carrying out the calculations for two hypothetical cases. Further, the effect of the oil-water viscosity ratio was examined by repeating the calculations, for several ratios of unity and greater, with the same relative permeabilities. Fi-nally, results are presented to show how the length of time a well must be swabbed to resume production depends on the length of time it has been subjected to invasion by water. STATEMENT OF THEORY Differential Equations Water is assumed to enter a producing formation which is initially at the connate-water saturation and contains no gas. The water and oil are treated as in-

By J. B. Cheatham, R. B. Paslay

Rock stresses and steady-state flow rates induced by the pressure gradient associated with the flow of formation fluid into a borehole have been analytically determined for a permeable, elastic material saturated with an incompressible fluid. In this analysis, the material properties and loading are considered to be symmetric about the axis of the borehole and independent of axial position. For Case I the material is assumed to have uniform permeability in the radial direction, whereas for Case 11 the permeability is assumed to have been reduced in a localized region adjacent to the hole by either normal well completion and production operations or deliberate plugging during air drilling. Results of a numerical example indicate that, in the absence of plugging, the rock shear strength must be approximately two-thirds the formation fluid pressure in order to prevent rock failure. The required rock strength is high for small radial zones of plugging and decreases as the region of reduced permeability becomes larger; however, a depth of plugging can be reached beyond which there is no real gain in strength, although the flow rate can be further reduced. INTRODUCTION During normal production of oil from a well, it is often desirable to increase the production rate of the formation fluid by increasing the pressure gradient through the formation adjacent to the borehole. Depending upon the magnitude of this pressure gradient and strength of the rock material, this production-rate increase can cause sloughing of the hole wall. In many cases, the production - rate increase can result in excessive sand production, increased wear of production equipment, lost production time and expensive workover jobs. In addition, the phenomenon of increased rock bit penetration rate with the use of a gaseous instead of a liquid drilling fluid has been observed in oilfield drilling operations and experimentally demonstrated by various investigators for several years. The improvement obtained by employing this technique can be quite significant and offers apromising method for reducing drilling costs. However, air drilling is currently limited to geographical locations where high-capacity water-bearing formations are not encountered. This limitation has prevented widespread adoption of air-drilling techniques, because the water influx into the borehole interferes with efficient removal of the drilling cuttings and usually results in a condition such that the bit becomes "balled-up" or stuck in the hole. In an attempt to remove the water - intrusion limitation from air drilling, various chemical and mechanical water shut-off methods have been proposed. Goodwin and Teplitzl suggested one such proposal whereby the permeability of the water-bearing rock structure was reduced in the vicinity of the borehole. Although the development of a shut-off method based upon this approach would certainly be welcomed by the oil industry, it is conceivable that, under certain conditions of the pressure gradient, strength of the rock material and depth of the modified permeability zone, a stress field can be created that will result in an unstable hole. As part of their study, an analytical solution is given for stresses in an idealized model of a hole and the surrounding rock material. The purpose of the present study is to extend the analysis of Goodwin and Teplitz to gain more insight into the details and consequences of excessive production rates and formation water shut-off. In particular, simplified models of these problems have been analytically examined, which makes possible the evaluation of the type of stress fields that can be anticipated as a result of these production and drilling practices. Both problems solved concern the determination of the steady-state volume flow rate of the formation fluid and the resulting steady-state stress and displacement distribution in a hollow, cylindrical configuration. The cylinder of Case I, corresponding to the production-rate problem, consists of a material with a constant permeability from the inside surface to the outside surface; the cylinder of Case 11, corresponding to the water shut-off problem, consists of a material with a constant permeability from the inside surface to an intermediate concentric cylindrical surface and a second constant permeability from the intermediate surface to the outside surface-

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.' In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By H. A. Wahl, J. M. Campbell

This study extends our information on solid-liquid slurries to the flow of sand in horizontal fractures. Inasmuch as this is basically an unsteady-state process, a comprehensive photographic study was undertaken in a 10-ft windowed cell to determine if the basic flow regimes described for steady-state flow in pipes applied to the subject process. Since the number of potential variables far exceeds the capacity of a single study, emphasis has been placed on the effects of sand concentration, oil viscosity and oil flow rate. The extensive photographic evidence obtained has proven very valuable in gaining an insight into the basic flow mechanisms. Being able to follow visually the flow characteristics that accompany the quantitative data is valuable in the application of the results. Although the use of dimensionless parameters was carefully investigated. it was found that the data obtained could be more easily, and as accurately, correlated by judicious use of the dimensional variables investigated. However, a study into the feasibility of scaling slurry flow was made in the event this technique is justified in future investigations. The data presented show that the pressure behavior observed in solids transport in pipes basically applies to slurry flow in horizontal fractures. The roles of the parameters are altered but a basic equivalence exists. The most significant correlating parameter was the oil viscosity (µo) and the bulk velocity of the slurry (vn), expressed as ''µv" product. The most significant correlation expresses the rate of advance of the sand as a function of the variables investigated. There are many practical ramifications of this phase of the investigation that should aid in better treatment design. Evaluation of sand advance rates provides a means of estimating sand placement efficiencies during a treatment and the resulting sand distribution in the fracture. The results show that sand placement efficiencies are low under typical treatment conditions. A brief description of the effects of overflushing is also included. INTRODUCTION The flow of sand-oil slurries in fractures is an area in which little basic knowledge is available. This stems to some degree from the fact that it is impossible to duplicate fractures at the surface. They occur in various shapes and sizes with an infinite combination of irregularities. Unfortunately, we can never "see" these fractures except in cores and by indirect means of measurement. In spite of this inherent difficulty, it is desirable to develop some basic concepts that will provide a better understanding of the sand transport mechanism. An insight into the problem is provided by investigations of fluid flow in rectangular conduits. Several studies on the flow of liquids in non-circular conduits1,13 show that a Reynolds number-Fanning friction factor relationship can be written if the hydraulic diameter is substituted for the regular diameter in a circular pipe. This hydraulic, or equivalent, diameter is taken as four times the cross-sectional area occupied by the flowing fluid divided by the wetted perimeter. Eq. 1 expresses an extension of this same work when applied to infinite parallel planes b distance apart.' Eq. 1 is a theoretical equation expressing the friction factor as a function of the Reynolds number for laminar single-phase fluid flow. This expression has been verified experimentally. The equivalent expression for a smooth circular conduit differs only in that the value of the constant is 16 instead of 24. Numerous studies have related friction losses to Reynolds number in both circular and non-circular conduits. These results are widely used and are not reviewed here. Huitt' investigated the effect of surface roughness on fluid flow in simulated fractures. He concluded that fluid flow in fractures may be treated similarly to fluid flow in circular conduits. This work, together with that of Nikuradse,' shows that surface roughness has no appreciative effect upon the resistance to flow in the viscous flow region. In the region of turbulent flow, surface roughness is a prominent factor. Hydraulic conveyance literature is another important source of information. Durand3 has attempted to organize systematically the variables involved in hydraulic-solid transport in pipes. He has classified the modes of flow into three types according to the size of the particles in the mixture— homogeneous mixtures, intermediary mixtures and heterogeneous mixtures. With the usual concentrations and flow rates used in hydraulic transportation, particles with diameters of less than 20 or 30 microns form eszentially homogeneous mixtures with water. The data show, however, that even small materials will tend to settle out under laminar flow conditions. Mixtures containing solids over 50 microns in diameter do not achieve total homogeneity even under turbulent flow conditions. Particles from 50 microns to 0.2 mm in diameter may be transported in fully suspended flow at normal transport velocities although the concentration in the vertical plane is not uniform. Above 2 mm in diameter solid materials are transported along the bottom of the conduit at a velocity substantially less than that of the liquid itself. Between 0.2 and 2 mm in diameter, the particles tend to be in a transition zone between heterogeneous suspended flow and deposit flow at normal hydraulic transport velocities. The sand sizes used in fracturing usually fall in this size range. It is interesting to note that the grain size range designated by Durand for this transition zone corresponds closely to the transition zone between

By G. R. Countryman, G. H. Thomas, I. Fatt

Procedures are described for scaling up turbulent friction pressure drops of inelastic fluids and laminar friction pressure drops of inelastic/elastic fluids in circular ducts. The laminar scale-up calculation method does not require the use of arbitrarily defined flow models, and can be performed directly from laminar capillary viscometry data, or by means of a numerical solution of the integral equation for Poiseuille flow, inputing true shear rate-shearing stress data from other simple shearing experiments. e.g. Couette and plane Poiseuille flows. The turbulent scale up procedure, based on the Dodge-Metzner correlation for inelastic fluids, requires evaluating the characteristic rheological parameters at the existing wall stress under laminar flow conditions. Since the wall stress is the quantity sought in a pipe flow scale-up problem, a trial-and-err or solution is indicated, and therefore a calculation method has been developed and programmed for a medium-size magnetic-drum-memory digital computer. Laminar flow data from other somces may also be adapted to this turbulent scale-upmetbod for inelastic fluids. Comparisons between predicted and experimentally observed friction losses for generalized Reynolds numbers ranging from 3 — 32.000 indicate an error band width of less than 10 per cent in circular tubes ranging in size from 0.5 to 1.89 in. in diameter. INTRODUCTION Considerable effort has been devoted to the problem of establishing an accurate procedure for predicting the laminar and turbulent flow behavior of non-Newtonian materials in pipes from data obtained with small scale laboratory or pilot plant equipment, as evidenced by the variety of reviews on the subject.1-3 Although there does not appear to be a universally accepted scale-up method for laminar flow, the various methods currently employed can be divided into two principal categories depending upon whether a functional relationship between shear rate and shearing stress is assumed, or whether a generalized correlation is adopted. The methods of Hedstrom4 and of Weltmann are typical of the first category, while the generalized correlation of Metzner and Reed6 illustrates the second category. Under appropriate conditions either approach yields a reasonably satisfactory description of laminar flow behavior. In contrast, the prediction of non-Newtonian transitional and turbulent friction losses is much more complex. For example, certain types of materials have been observed to sustain laminar flow at much higher flow rates than Newtonian liquids. When turbulence does develop, the level of agitation is damped to such an extent that the friction factor is lower than that of the original low viscosity Newtonian medium. Extremely broad transition regions and "diameter effects" have also been noted in the turbulent flow of certain chemically complex materials.' Aside from the latter complications, which are attributed in part to viscoelasticity, the existence of a variety of scale-up procedures for predicting transitional and turbulent friction losses is due principally to the chioce of viscosity parameter used in the definition of the Reynolds number. In contrast, Dodge and Metzner have demonstrated that the friction factorReynolds number relationship for inelastic fluids can be satisfactorily generalized provided the fluid property parameters are evaluated at the existing wall shearing stress.* However, the quantity usually sought in a pipe flow scale-up problem is the wall stress, and hence a trial-and-error procedure is required when dealing with non-power law materials. In this report we discuss two calculation methods: (1) for determining the wall stress, and hence the friction pressure drop, for inelastic fluids under conditions of turbulent flow by means of an iterative procedure, and (2) for predicting laminar friction pressure drops without recourse to arbitrarily defined flow models.

By O. D. Gaither

This paper is an analytical study of the flow of fluids through small vertical conduits. Small conduits are defined as 11/4-in. nominal diameter tubing size and smaller, and approximately twice this area for annular conduits (i.e., 1- X 21/2-in. annulus and smaller). Experimental data are presented for the 1-X2-in. and 11/4- X 2%-in. annuli, and the I-in. and 11/4-in. tubing, since these represent the small conduit sizes and configurations generally encountered in oilfield applications. Data have been gathered for these conduits for single-phase water, single-phase gas and two-phase water-gas mixtures, with particular emphasis on high gas-liquid ratios. Water rates in excess of 2,000 BID and gas rates in excess of 2.5 MMcf/D, and two-phase flow ratios in between these two, represent the scope of the data gathered. Existing equations have been applied to predict flowing pressures and compared with experimental data. New correlations have been developed. INTRODUCTION The increased economic pressure on the domestic oil industry in the United States has constantly required the use of new techniques and equipment designed to reduce the cost of finding and producing oil and gas. Since tangible items are most readily apparent in economic analysis, the advent of lower-cost well completions was inevitable. One of the methods used to reduce costs which has received widespread attention is the slim-hole completion technique where tubing is used as the well casing and in which small conduits are used for tubing if necessary. Small conduits, defined by Kirkpatrick1 as "11/4-in. diameter nominal tubing and smaller for tubing flow and less than twice the 11/4-in. diameter nominal tubing internal flow area for annulus flow", have also found widespread usage as siphon strings for de-watering gas wells and as "kill" strings in deep high-pressure oil and gas wells. The growing use of small-diameter tubing has resulted in an increased need for development of improved methods to measure or predict flowing bottom-hole pressures since the physical dimensions generally preclude the use of subsurface-recording pressure gauges. Even in the cases where small bombs are available, the relatively high velocities encountered at nominal flow rates make it necessary to use excessive weight bars or special hold-down devices. Attempts to use recognized correlations to accurately predict flowing or gas-lift performance in wells equipped with small conduits have been generally unsuccessful. Insufficient field data were available to allow the development of a correlation on this basis, and an experimental approach was applied in an attempt to obtain a workable relation. The experimental approach used to obtain the data presented in this paper was actually a compromise between a field installation and a laboratory study. A test well 1,000 ft in length was used to obtain flow data on single-phase liquid, single-phase gas and two-phase water-gas flowing mixtures. Liquid rates up to 2,200 B/D and gas rates up to 3 MMcf/D were used in the single-phase flow studies. Two-phase flow rates from 100 to 600 B/D with gas-liquid ratios from 500 to 8,000 cu ft/bbl were recorded. Experimental data were obtained for single- and two-phase flow through 1-in and 11/4-in. nominal tubing, and through the annuli between 1- and 2-in. and 11/4- and 2%-in. nominal tubing strings. Experimental results for the two-phase flow are compared to the Poettmann-Carpenter correlation2 which is widely used as a comparative standard for development of multiphase flow predictions in flowing and gas-lift wells. Correlations developed by Tek,3 Baxendell and Thomas" were also investigated. The experimental data recorded herein fell in between the two flow regimes as defined by Ros," and this correlation also failed to yield satisfactory results. The fact that existing correlations failed to confirm the experimental data led to the need for development of a new correlation. Although a two-phase flow study was the primary objective of this investigation, data were also recorded for single-phase flow of water and gas, and constants were developed relating to pipe roughness and equivalent diameters for annular flow. These single-phase studies assisted materially in the development of certain of the two-phase flow results. Considerable previous work has been published which presented relationship of surface measurements to bottom-hole condition. The works of Buthod and Whiteley,6 Jones,' Poettmannb and the Texas Railroad Commission" are classic examples of the successful use of mathematical relationships which allow acceptable predictions of subsurface pressures, when gas is the flowing fluid. Darcy and others have derived relationships which may be used with minor modifications to predict subsurface flowing conditions in injection and water-supply wells. As previously stated, the application of the single-phase flow relationships

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By J. C. Savins, G. C. Wallick, W. R. Foster

The dual differentiation-integration method of rbeological analysis is applied to Couette flow. Using machine processing techniques, a spectrum of characteristic derivative functions for a variety of ideal Generalized Newtonian and viscoplastic models has been developed; As for the case of Poiseuille flow the functions for Generalized Newtonian models as a class are strikingly different from the corresponding functions for the class of viscoplastic models. It is shown that this dual scheme of analysis is a highly sensitive analytic method for dotermining the applicable range if a rbeoloaical model. The unique characteristics of this function in the case of viscoplastics may lead to a more precise detection and evaluation of the yield point or yield stress in these materials. INTRODUCTION It has been shown 1,2 that the dual differentiation-integration method of analysis is a discriminating and flexible method for interpreting flow behavior and determining the applicable range of a particular model from Poiseuille flow experiments. In the preceding paper3 the basic equations governing the Couette flow experiment were reviewed and the significance of changes in boundary conditions on data analysis in the case of the viscoplaaic discussed. In this paper the dual method of analysis is applied to Couette flow using the suites of rheological models considered previously.

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle' published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer' in this study. The squase drainage system of a well was rep-

By J. O. Scott

Transient pressure behavior of wells intersected by a single vertical fracture has been examined by means of a heat pow analogy. Results are correlated in terms of dimensionless pressure change and dimensionless transient time. The resulting curves are found to lie between the dimensionless curves for a cylindrical well and a line source when effective well radius is expressed as one-fourth of the total fracture length. Results are also shown for various degrees of afterflow. Use of the curves provides a means of determining reservoir permeability, wellbore radius, and thereby fracture length, even when the final slope of the transient curve is not obtained. Superposition of curves may be used to confirm existence of vertical fractures in the reservoir adjacent to the well or to indicate a damaged zone on the fracture face. INTRODUCTION Hydraulic fracturing has become a standard well completion practice for the purpose of increasing flow. Results are normally gauged in terms of some sort of "stabilized" flow rate established before and after the treatment. This procedure may be misleading because pressures in or around the well do not become "stabilized" during the test period. Transient pressure tests on fractured wells can overcome the objections to stabilized flow tests by indicating when a stable pressure gradient is reached. In addition, the transient pressure tests can be used to determine formation flow capacity and effective wellbore radius. The effective wellbore radius may be used as a measure of the success of the fracturing operation. The slope and position of the transient pressure-log time curve may be used to determine the flow capacity and wellbore size after sufficient lapse of time so that the pressure gradient in the vicinity of the fractures becomes constant. However, in tight reservoirs or in short tests this condition may not be reached. Presence of the fractures in tight reservoirs may cause a constantly increasing slope to the transient pressure curve. If this slope is picked too soon, formation flow capacity will appear high and the fracture size will appear too small. This paper is intended to clarify the early transient behavior of vertically fractured wells. It shows how formation flow capacity and wellbore size can be determined even though the maximum slope of the transient pressure curve is not obtained during the test. Development of the techniques of transient pressure analysis for wells has been summarized by Perrine.' He reviews the various definitions of wellbore effects such as skin effect, productivity ratio, damage factor and condition ratio. In the present paper, use of these terms is avoided by defining an effective wellbore size. For the fractured well this effective wellbore size is larger than the actual wellbore. Assumptions made are constant flow rate at the well, constant fluid compressibility, constant fluid mobility and uniform porosity and formation thickness. From the basic differential equations of flow, two different solutions may be obtained. The first, the line source solution, is commonly used in transient pressure analysis.' It expresses the change in pressure at any radius due to withdrawal or injection of fluid at the line source from an infinite reservoir at uniform initial pressure. This equation, in oil field units: is

By R. H. Kolb

A long term project at Shell Development Co.'s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.' THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit' was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By J. E. Warren, J. H. Hartsock

An asymptotic solution to the equation that describes the flow of a slightly compressible fluid in an infinite porous medium has been used to estimate the interaction between two adjacent wells producing from a common reservoir. A direct method for approximating the interference time defined by Stevens and Thodosl has been suggested. An alternative definition for the time of interference, based on the minimum pressure change in the interference region, has been proposed; also, a direct method of determination has been prescribed. Examples have been employed to illustrate the use of both methods.

By E. A. Ernst, N. F. Carpenter

The benefits derived from an acidizing treatment are a function of the penetration achieved by the acid before complete spending. Additional penetration may be achieved by (1) controlling acid leak-08 into formation pores in the channel faces, and (2) retarding the reaction rate of the acid. A recently developed chemical additive consists of a synthetic polymeric material which absorbs hydrochloric-acid solutions, when suspended therein, swelling up to 40 times its original volume. These swollen particles have the ability to deform and seal-08 formation pores, providing fluid-loss control. In addition, they provide a diffusion barrier between the fracture face and the acid solution, prolonging the spending time of the acid. Field applications of this new technique have shown promising results. A method of conducting acid fluid-loss tests, using carbonate cores, is believed to provide fluid-loss data that are more representative of formation conditions than the conventional filter-paper determinations. INTRODUCTION The concept of oilwell acidizing has changed since its first commercial application, 30 years ago. Originally, it was visualized that the acid penetrated thousands of tiny pores and flow channels in the matrix rock, enlarging them by dissolving the carbonate walls. The resultant permeability increase was assumed to be the responsible factor in increasing production from the well. Recent laboratory studies,' however, have shown that this does not provide the complete picture. Although this type of individual pore penetration by the acid does take place during acid "soaks", designed to overcome "skin effect" due to mud invasion in the immediate vicinity of the wellbore, many years of experience have shown that considerable pressure is required to attain any appreciable injection rate into the fine capillary pores of the rock. During most acidizing treatments, the bottom-hole pressure build-up due to the restriction of flow into the formation exceeds the "breakdown" pressure of the rock so that a fracture is induced. In most cases, such fractures open up along natural, incipient fissures and zones of weakness in the rock and, therefore, tend to follow the natural stress pattern of the rock—whether it be horizontal, vertical or inclined. Because of the comparatively greater permeability of the channel in relation to that of the matrix, the bulk of the acid volume is diverted into the newly opened fracture. Here it quickly penetrates the formation, opening and ex- tending the fracture in much the same manner as a conventional fracturing fluid. Unlike the fracturing fluid, however, most acidizing solutions contain no propping agent; thus, the open fracture will again close when the injection pressure is relieved. Laboratory studies2 have shown that in many cases the etching of the fracture faces, resulting from the reaction between the acidizing solution and the carbonate rock, is nonuniform due to the heterogeneity of the rock structure. As a result, the two fracture faces no longer match when pressure is released, and support pillars and intermediate voids remain, forming a high-conductivity channel for well fluids. Unfortunately, this is not true over the entire area of the fracture, but only over that portion of the fracture where the rock has been partially dissolved by the acid. The acid solution spends as its travels away from the wellbore; once it has completely spent, even though it may provide additional mechanical fracture extension, no additional benefit due to etching of fracture faces can be expected. Studies of acid reaction rates under formation conditions,3 observing the effect of different variables upon spending time, have shown that the reaction was often so rapid that very little penetration of the formation occurred before the acid was spent. Study was undertaken to devise methods of increasing the penetration of the acid before spending, so as to provide greater benefit from the acidizing treatment by etching a greater portion of the fracture faces. Several techniques were devised to accomplish this purpose. First, chemical additives were developed which were designed to retard the reaction rate of the acid, causing it to penetrate a greater distance from the wellbore before finally becoming spent. Another method was to increase the injection rate of the acid. However, it was found that the resultant increased shear tended to accelerate the reaction rate of the acid, partially offsetting the benefits of the higher injection rate insofar as achieving increased penetration before spending was concerned.' Another approach to the problem of achieving increased penetration was the development of fluid-loss additives for acid solutions, which would minimize the volume of acid lost into formation pores in the fracture faces and provide maximum fracture extension for the volume of acid injected during the treatment. The use of fluid-loss additives is now considered the most effective method of providing maximum fracturing-fluid efficiency.~ Unfortunately, this latter technique does not solve the problem of rapid reaction rate, with consequent limitation of the fracture area benefited by reaction with unspent acid. A newly developed acid additive overcomes many of these limitations by providing the dual benefits of fluid-loss control and mechanical retardation of acid reaction

By R. E. Zinkham, R. J. Goodwin

A mathematical study has been made of the amount of support a cement sheath could provide to casing cemented into the earth. Several assumptions were required to make the analysis, but only two of them are limiting: (I) the pipe must be completely surrounded with cement, and (2) any mud filter cake between the cement and formation has the same physical properties as either the cement or formation. The calculations showed that little support would be provided to the pipe before an unsupported cement sheath failed in tension; however, when the cement is confined between the pipe and wellbore and is loaded in compression, the pipe could receive a considerable amount of support. In fact, the theoretical results indicate the lower grades and larger sizes of pipe could have their working pressures doubled when reasonable compressive loads were applied to a surrounding cement sheath. These data are shown in six charts. Other down-hole conditions such as setting the cement under pressure, increased temperature and cement confinement all tend to increase the potential usefulness of the sheath. Because of size limitations, a laboratory program to verify the most important results of this mathematical study would be very difficult. However, small-scale field tests would be practicable. This paper shows that, if a solid cement sheath can be obtained in the field by either primary cementing or by repair after detection of flaws by surveys such as the new cement-bond logs, the use of this approach to reducing pipe costs merits further consideration. INTRODUCTION A modification in casing design practices is proposed which may either reduce the amount and grade of steel required to contain a specified internal pressure or permit the working pressure to be increased for a specified weight and grade of pipe. One of the more important considerations in casing design is its resistance to collapse; however, Bowers' and, more recently, O'Brien and Goins' have shown many casing programs are unnecessarily conservative in this respect, and they have indicated how savings can be made by designing for more realistic down-hole conditions. Earlier, Saye and Richardson howed that pipe costs could be reduced by considering the cement sheath as a part of the casing string when collapse resistance was being calculated. More recently, Rogers4 has raised the question as to whether a cement sheath might be considered in the design for burst resistance of the cemented casing. Calculations have been made for the increased burst resistance a cement sheath would provide for casing in a wellbore, and the results show that a sizable amount of support could be obtained in some instances. These data are presented in addition to a discussion of several other factors that are considered to affect the burst strength of pipe supported by cement. Two types of support are treated: Case I for tensile loading of the unconfined cement sheath, and Case for compressive loading of the confined cement sheath. ANALYTICAL TREATMENT AND RESULTS CASE I—TENSILE STRESSES IN AN UNCONFINED CEMENT SHEATH Conditions like this would most likely occur in a greatly enlarged portion of the hole where the cement was not in immediate contact with either the formation or a thin and hard mud cake. The mathematical analysis for this condition, as shown in the Appendix, rests on the following concepts. Pressure inside a unit length of pipe causes: (1) a tensile or tangential stress to be exerted over the longitudinal cross-sectional areas of the pipe and cement; and (2) an equal amount of strain in both the pipe and cement that is uniformly distributed over the wall thickness of each. This analysis was then used to make several calculations for a cement sheath around 51/2-in. OD pipe. The results are illustrated in Fig. 1, which shows that a tensile stress of 500 psi is imposed on a 5-in. thick sheath when the casing contains a pressure of only 1,450 psi. It also shows that a 10-in. thick sheath would be stressed to 500 psi in tension when the pipe contained a pressure of only 2,350 psi. Alternatively, if the stress analysis is made by means of the Lame thick-wall cylinder theory, the inner fibers of the 10-in. thick sheath will be stressed to 500 psi in tension when the pressure in the pipe is only 990 psi. This, of course, reveals that an unconfined sheath is of little support to the pipe in burst; however, an entirely different result is obtained when the cement is confined between the pipe and formation.

By K. E. Brown, F. W. Jessen

By utilizing an 8,000-ft experimental field well equipped with 10 gas-lift valves and 10 Maihak pressure recorders, gas-lift tests were conducted with port sizes ranging from 5/16 through I in. The well was equipped to provide accurate means of measuring surface pressures, temperatures, quantity of injection gas and fluid production. The tests were conducted in 2%-in. OD tubing, and the well was making 95 per cent water. A complete evaluation of gas-lift-valve port sizes shows the relationship of per cent recovery, gas-liquid ratios, minimum pressure created at the operating valve and horsepower requirements for each port. The length of time necessary for the fluid in the tubing to reach equilib.rium conditions after each cycle was recorded. Fallback of fluid at depths of 477, 969, 1,685, 2,493 and 4,290 ft was noted. For each port size, pressure loads of 2.50, 300, 350, 400 and 450 psi were lifted with a valve operating at approximately 550 psi at 6,000 ft. Gas-liquid ratios for each load were varied from excess gas to a gas volume per cycle whereby the load failed to reach the surface. Numerous curves are presented in evaluating the accumulated dara. The results show a 1-in. port to be the most efficient under all conditions. The production of intermittent liquid slugs against different-sized surface chokes was evaluated. These tests were conducted from a 7/16-in. ported valve at 4,072 ft. Tests indicate that, when possible, a %-in. in diameter choke or larger should be used at the surface. In the past few years most of the advancement in gas-lift operations has been made in continuous-flow operations. Yet, it is estimated that at least 70 per cent of the wells on gas lift in the United States are of the intermittent type. Since the term "slug flow" is sometimes used in both intermittent- and continuous-flow operations, it would be well to distinguish between the two types of flow. Continuous-flow gas lift is defined as a method whereby the fluids are produced at a continuous rate at the surface. This generally requires a continuous injection of gas through a surface choke; however, various other control devices sometimes are installed to eliminate freezing, to shut-off gas during natural flow periods, etc. The actual flow of fluids in the tubing may be of the slug type (one of many flow patterns known to exist in continuous flow). Intermittent flow is defined as a method of gas lift whereby the liquid is produced in separate piston-type slugs. Perhaps this type of flow could best be thought of as a ballistic-type flow where the liquid leaves bottom as a piston, propelled by a slug of expanding gas. Gas generally is injected through some type of control at the surface at predetermined intervals. However, the valve may have characteristics whereby gas can be injected through a small choke and still result in a ballistic-type flow. The purpose of the experimental work was to evaluate the most efficient port size to be used on the operating valve for the ballistic type of lift and, in addition, to establish the importance of utilizing a surface choke large enough to allow slugs to be produced without detrimental effects. This work is part of a compre- hensive study of both intermittent-and continuous-flow gas lift, representing a joint project conducted by the Ohio Oil Co., the Sun Oil Co., Otis Engineering Corp, and The U. of Texas. The problem of evaluating port sizes has been given little previous attention. Some work undoubtedly has been done which has not been published to date. Some tests were conducted when the wireline, mechanically-opened valve (Nixon) first came on the market. This valve was capable of utilizing full tubing area as its port size. It is known that this was a very efficient valve, but to the authors' knowledge the results of tests have never been published. EXPERIMENTAL EQUIPMENT These tests were conducted on an actual field well, the Ohio-Sun Unit Well No. 2-E, in the North Markham-North Bay City field, Matagorda County, Tex. The well incorporated 23/8-in. OD tubing and produced 95 per cent water. Since the running of equipment was to be quite elaborate and expensive, a well was selected in which both intermittent- and continuous-flow tests could be conducted. This particular well was capable of producing in excess of 1,000 B/D of liquid (95 per cent salt water), yet with a 3/64-in. in diameter bottom-hole choke, production was controlled to 82 B/D. Most of the intermittent tests were conducted at this low rate. Figs. 1 and 2 show all the surface and down-hole equipment. As can be seen, every attempt was made to insure that ample equipment was available for reliable testing procedures. Fig. 1 shows the surface testing equipment. The input gas was controlled first by a regulator, then