Search Documents

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By Jack White

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the l l-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the ll-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 1% in. and a further gain of work accomplished of 2.1 pct when we went from 1 % in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By P. Somasundaran, D. W. Fuerstenau

The length of the collector is found to influence the flotation of the mineral even at incipient conditions, which are below the concentration at which interaction at the solid-liquid interface begins to take place to form hemi-micelles. To study this dependence, concentration for incipient flotation of quartz was determined as a function of pH with collectors of various chain lengths. The observed effect of chain length on flotation is ascribed to that of collector adsorbed on the bubble surface. In previous studies, it was shown that at low concentrations the alkyl collector ions adsorb at the solid-liquid interface as individuals.''2 At higher concentrations, the collector ions adsorbed at the solid-liquid interface associate with each other to form two-dimensional aggregates called hemi-micelles. Above the hemi-micelle concentration, the length of the hydrocarbon chain is extremely important since the hydrocarbons are in effect removed from water during the association, making the energetic conditions more favorable for adsorption at the interface. Because of this enhanced adsorption, one observes a very rapid increase in flotation associated with the hemi-micelle formation at the solid-liquid interface. However, a dependence of flotation on the chain length at concentrations below that required for hemi-micelle association was also observed,' and this cannot be explained by the above mechanism which postulated hydrocarbon chain interactions only at the solid-liquid interface. This prompted an investigation into other possible reactions of the hydrocarbon chains and an examination of the conditions at the bubble surface involved in the flotation system and how these observations might explain the reactions at the solid-gas interface which cause the particle-bubble attachment required for flotation. To obtain more information on chain length effects, flotation, under incipient conditions, was tested by vacuum flotation techniques. The collector-concen-tration-pH relationships for flotation of quartz with alkyl ammonium acetate collectors was delineated by observing the pH at which quartz particles begin to float to the liquid surface. By investigating flotation as a function of pH, it was also possible to study the effect of neutral molecules on incipient flotation conditions, since the aminium ions hydrolyze to amine molecules at higher pH values. EXPERIMENTAL WORK Brazilian quartz specimens were crushed and sized, and the 270 x 400 mesh fraction was used for flotation studies. The samples were leached with concentrated hydrochloric acid until no coloration of the acid occurred. The leached material was washed free of chloride ions and stored in distilled water. The vacuum flotation technique developed by Schuhmann and prakash3 was used to determine the critical pH-concentration curves. This method, which can be used to delineate conditions for incipient flotation, is fairly simple and rapid. About 0.5 gm of 270 x 400 mesh quartz was placed in a 100 ml graduated cylinder which was then filled to the 100 ml mark with the collector solution made from high-purity alkyl ammonium acetate salts. The water used for the test was conductivity water saturated with air that had been passed through a cleansing train consisting of Drierite, Ascarite, a water wash bottle, and a trap. After the pH was adjusted, the cylinder was then conditioned for thirty minutes. In the tests where an acid pH was desired, sufficient acid was added before the collector solution to avoid any effect due to slow desorption of collector from the quartz surface. After conditioning, vacuum was applied to the system and the flotation or nonflotation of the quartz was noted. The pH at which the quartz particles began to float to the liquid-gas interface was taken as the critical PH. Critical pH curves were thus determined for different concentrations of the various collectors. Hallimond tube flotation data were taken from the authors' previous publication1 for correlation with that from the vacuum flotation. RESULTS AND DISCUSSION The results of vacuum flotation studies for determining critical pH-concentration curves, i.e., curves which delineate conditions for incipient flotation, are shown in Fig. I. In generaI, all the curves exhibit an upper and lower pH limit between which flotation will

Jan 1, 1969

By C. C. Harris

A critical literature review leads to a descriptive model of tumbling mill operation based upon energy partition concepts and the necessary requirements for particle fracture. As grinding proceeds into the ultra-fine region, conditions which are of little significance during normal operations gradually become controlling. These involve increasing resistance to fracture and an increasing tendency to aggregate as particles become smaller, and a growing fraction of the power input being consumed fruitlessly. The result is that fineness asymptotes to a maximum value as comminution proceeds indefinitely; thus where t is time, p and n are experimentally determined parameters, and Ø is a measure of fineness, which is presumed to be proportional to specific surface area, or proportional to the reciprocal of the size modulus (provided that the distribution modulus remains constant with time), or both. Ø, is the asymptotic value of Ø and is a measure of the grind limit. A method for its graphical determination is given. In a previous paper1 the physical and mathematical principles requisite to a study of the role of energy in comminution were reviewed. The micro-process of comminution — or the comminution event — can be investigated in terms of (a) the magnitude of the force-field localized around the individual particles which gives rise to the stresses generated in the particles, which in turn induces their fracture, and (b) the distribution of fragment sizes, should the event prove fruitful. The entire fragmentation operation can be considered to be the totality of its individual events, and in order to obtain a single independent variable of the process it is necessary to transform and sum the local stresses in terms of energy.1 This energy, however, will account for only a fraction of the energy input to the comminution process, the actual magnitude depending upon the kind of mill and several related factors. From the comminution viewpoint the primary function of a mill is that of stressing as many as possible of the individual particles of the charge to failure, with the maximum economy of energy expenditure. This is difficult indeed to achieve, for stressing a particle does not always break it, while the overwhelming portion of the energy input is involved with various internal mill processes which — almost incidentally — determine the magnitude, frequency, and manner in which the forces are applied to the particles. Essentially, these processes depend upon the mill dimensions, loading and speed, and they may be little affected whether fracture occurs or not. These processes must be delineated if a complete description of the role of energy in comminution is to be given; the energy account sheet1 (Fig. 1) in showing how the energy is partitioned for the requirements of the several functions it performs, provides a framework for the development of a model of the comminution process. Actual numerical values for the variables appearing in Fig. 1 will depend upon the mill, materials, and operating conditions. A possible general relationship between the variables will be suggested in this paper. Before proceeding further, a cautionary note must be issued. It was pointed out in an earlier paper' that while energy input is not changed by increasing the power and decreasing the time in the same proportion, and vice versa, the results of the process in terms of particle fineness may be different. Thus, although energy is chosen as the independent variable of a comminution process, it is not absolutely independent, and care must be exercised to ensure that it is used within its range of valid application. Time has the necessary independence, and it will be used in place of energy where it is appropriate. The residence time in a mill is usually of the order of minutes. Under these conditions the particles are subjected to "... a relatively constant fracture producing environment".2 However, under the more rigorous conditions of greatly extended time, which pertain in ultra-fine grinding, indications are that the fracture producing environment no longer remains constant; this is the major subject of this paper. At this extreme limit the mill is probably taxed to its utmost, and at the same time the bulk material properties are becoming closer to ideal, while the physico chemical effects associated with surfaces, edges and corners are multiplying. (The edge length per unit volume is proportional to the square of the specific

Jan 1, 1968

By J. M. Cases

Study of the normal interaction between flotation collectors and the silicates through measurement of the electrokinetic potential carried out by the streaming potential and flotation recovery methods indicates that the interaction is wholly 07 partly of electrostatic origin. In some cases, it partly consists of the chemical affinity of the polar head of the collector for the active surface sites. Reagents composed of a polar head and a paraffinic chain and forming micelles in solution were used as flotation collectors. They are sodium dodecylsulfate (anionic collector) and dode-cylammonium chloride (cationic collector). The adsorption isotherms on biotite of alkylamine chloride having 10 to 18 carbon atoms in their chain all show a sharp change in slope relevant to the condensation of alkylammonium ions into bidimensional phase.1-1 Condensation is possible because of the relative homogeneity of the adsorbing surface and of the very strong lateral binding forces through Van der Waals type bonds in the adsorption layer. The different isotherms are seen to coincide when, instead of the equilibrium concentration, the under-saturation ?µ = kT In C/C, is plotted in abscissa, C representing the concentration of the solution with which the adsorbed layer is in equilibrium and C, the saturation concentration of micelles in solution or. critical micellar concentration. More particularly, the undersaturation ?,u1*, corresponding to a surface coverage 6 of 0.5, is equal to Since silicates immersed in aqueous solutions show a surface charge which is a function of pH, it is of primary importance to study the influence of this parameter on the adsorption of collector ions acting as Strong electrolytes in the pH range where they are utilized. The aim of this present paper is to determine by studying electrokinetic phenomena and recovery curves effectuated with a cationic collector and a anionic collector, the nature of the normal adsorbate-adsorbent interaction. Tables 1 and 2 sum up part of the results previously obtained'H11 for the determination of the point of zero charge of the silicate studied by the streaming potential method. Throughout the remainder of this paper, the surface charge will be considered positive for all values of pH below the point

Jan 1, 1971

By R. W. Smith, R. W. M. Lai

Although several recent papers have shown that equilibrium contact angle in dodecylamine solution-quartz systems can often be directly correlated with flotation behavior, it appears that under conditions of relatively high amine strength and pH such a correlation can't be made. Under these conditions, when there are precipitated amine dipoles present, it appears that a dynamic contact angle formed immediately after introduction of fresh gas bubbles into the system is also of importance. The dynamic angle decreases in magnitude as a function of time. Apparently the decrease is the result of changes in interfacial tensions (liquid-gas and solid-gas) as a function of time. Dynamic angles of the type described can't be observed in trimethyldodecylammonium chloride solution-quartz systems. Several recent papers1-3 have shown quite conclusively that contact angle data can often be correlated directly with flotation behavior in cationic surfactant solution-quartz systems. At the same time, Iwasaki, Cooke, and Colombo4 have shown data for a dodecylammonium chloride solution-goethite system where, in the vicinity of pH 12 and a collector concentration of 10" M, 100% flotation occurs when equilibrium contact angle appears to be zero. A clue to this discrepancy can be found in the work by smith2 who reported the occurrence of dynamic, time dependent, contact angles in a quartz-dodecyl-amine solution system at relatively high pH values and at surfactant concentrations greater than or equal to 10-4 M. It was found that under these conditions, if a fresh bubble was brought into contact with a properly conditioned and polished quartz surface, a large angle was obtained. The large angle, however, instantly started to diminish in magnitude, sometimes to a smaller stable angle and sometimes to its complete disappearance. Also, if the bubble was preconditioned for some minutes (or sometimes even seconds) in the same amine solution, the smaller or sometimes zero stable angle was obtained when the bubble was brought in contact with the quartz surface. One is immediately led to the thought that perhaps it is these dynamic angles when they exist, not stable angles, that are of primary importance in flotation. The present investigation attempts to further study the relationship between contact angle and flotation

Jan 1, 1967

By E. B. Fitch, E. C. Johnson

The operating behavior of liquid-solid cyclones is outlined, together with the nature and range of the process results obtainable, to serve as a background for engineers wishing to consider application of this new process tool. BY now most engineers are familiar with the liquid-solid or Dutch State Mines cyclone. However, it should be helpful to know exactly what it is that the equipment does and what its limits are. Without going into cyclone theory, this paper will describe the operating characteristics of Dutch State Mines cyclones. These are manufactured under license in this country and sold under the trade-marked name of DorrClone. The physical construction of the liquid-solid cyclone has been covered in many papers,'-' the DorrClone in particular being described in some detail by Weems. Fig. 1 shows the unit in cross-section. The feed enters at C. The coarse, heavy particles are thrown centrifugally to the periphery and make their way down the wall to the apex where their rate of discharge as underflow is controlled by an adjustable rubber apex valve. As the apex diameter is decreased the solids build up behind the valve, producing a denser underflow. Meanwhile the fine particles are swept into the upward flowing vortex stream which exits as overflow through the vortex finder, F. Flexibility to produce the specific result desired in a particular process is achieved by providing means for varying the areas of the entrance, vortex discharge, and apex discharge. The entrance area may be varied by insertion of special shims. Vortex discharge area may be changed by use of different-sized vortex finders which are interchangeable. Similarly, the different sizes of apex valves are interchangeable and in addition each apex valve is variable down to about 60 pct of its maximum diameter. A most significant primary distinction to make is that although liquid-solid cyclones have been sometimes called thickeners, they actually are classifiers, and very potent ones. They are almost never thickeners in the special sense that many metallurgical engineers understand the term. There would be no profit in quibbling over the definition of a word, but when the application of cyclones is considered, it will help to understand the difference be- tween two mechanisms, one of which will be called classification, and the other thickening. In what is called thickening the fine solid particles present in the feed hold together by surface attraction during the sedimentation process. The loose network of particles thus held together constrains all particles to settle at approximately the same rate, the larger ones dragging the smaller ones down. As a result, pulp settles with a sharp line of demarcation between solids and a relatively clear supernatant liquid. Essentially all the solids, regardless of their fineness, pass into the thickened underflow, and a clear overflow is separated. In classification, on the other hand, the interparti-cle forces are relatively insignificant as compared to the settling force on the individual particles, and are insufficient to prevent independent movement of the particles. The coarsest, heaviest particles settle most rapidly through the pulp, passing more slowly settling fines. Particles coarser than the mesh-of-separation essentially all settle into the underflow, but if the feed contains any particles finer than the mesh of separation, at least part of them will appear in the overflow. A clear supernatant or overflow can be obtained only if there are no undersize particles present in the feed. Thus it will be seen that classification is impossible under ideal thickening conditions. The finer particles are pulled down at essentially the same rate as coarser particles, and there is no separation on the basis of particle size. The surface attraction holding the particles together in a thickener is usually feeble. Whenever the sedimentation force on any particle is strong with respect to the interparticle forces, that particle can pass through the tenuous structure and settle independently. There are at least four ways of making the sedimentation force strong, with respect to the interparticle forces, and obtaining classification. First, and most obvious, the particles may be large and heavy. Thus coarse sands settle out in a beaker or Dorr thickener ahead of the rest of the thickening solids. Second, the interparticle forces may be altered by physicochemical means; i.e., it is often necessary to add dispersing agents to destroy the interparticle forces and permit classification to take place. Third, the interparticle forces may be reduced by dilution of pulp. It is well known that to obtain the most efficient separation of

Jan 1, 1954

By Howard R. Keil

Reactor at Carlton mill successfully calcines pyrite-telluride flotation concentrate for cyanidation. CARLTON mill in the Cripple Creek district, 45 miles southwest of Colorado Springs, Colo., has been in operation for approximately three years, treating the custom sulpho-telluride ores formerly handled by the Golden Cycle mill in Colorado Springs. At the new mill the pyrite-telluride flotation concentrates have been roasted, prior to cyani-dation, in a Dorrco FluoSolids reactor, which has proved capable of yielding calcine readily amenable to cyanidation. Incoming ores are crushed at Carlton to % in. and sampled in 30 to 75-ton lots before the individual lots are mixed in the fine ore bin. The composite ore then goes to the grinding circuit. Classifier overflow from the grinding circuit is treated by flotation to produce a concentrate containing approximately 85 pct of the values in 5 pct of the weight. The flotation concentrate goes to the FluoSolids reactor prior to cyanidation. Cyanide solution values are recovered by zinc dust precipitation. Flotation tailings are thickened and cyanided, the values from this part of the circuit being recovered from solution by activated carbon. Gold values in the flotation concentrates consist of a small amount of finely divided metallic gold; the tellurides, sylvanite and calaverite; and gold very intimately associated with the pyrite. The metallic gold and a part of the telluride values can be extracted from the concentrates by cyaniding without roasting. However, extraction on the tellurides by this method is not satisfactory, and the pyrite values are so intimately associated with the pyrite that very fine grinding and cyanidation for a prolonged period under ideal laboratory conditions does not yield good recovery. Upon roasting, the tellurides are oxidized to very finely divided metallic gold which is readily soluble in cyanide. The pyrite is oxidized mainly to a porous iron oxide which allows cyanide solution to penetrate to gold particles and take them into solution. Feeding the Reactor Flotation concentrates move by gravity to a thickener. Thickener underflow is discharged at approximately 60 pct solids, by means of a diaphragm pump, into a storage and blending agitator. From here the concentrates are pumped to a disc filter. The filter cake, at 84 to 88 pct solids, drops directly into a repulper where it is repulped into a slurry of 78 to 80 pct solids. The repulped filter cake flows into a 6x6-ft slurry agitator from which it is fed directly into the reactor by the Moyno pump. The Moyno pump has eliminated a large number of difficulties that were first encountered in feeding a wet concentrate to the reactor. On the original installation in Canada a screw feeder was used to introduce the filter cake directly into the reactor. Since the reactor is under a slight positive pressure it was necessary to have a suitable seal to prevent gas escaping from the reactor at this point. When the concentrates produced in flotation were coarse or granular they could be readily fed to the reactor but when fine-textured, clayey concentrates were produced a great deal of trouble was encountered.

Jan 1, 1955

By G. O. Prickett, P. Somasundaran

An experimental progmm based on statistical principles is used for optimizing a flotation operation for the separation of minerals. In this case, flotation of sylvite from sylvinite ore with amine and starch as the flotation reagents was studied to find the optimum reagent levels at various slime levels. The experiments were first done on a two-level three-factor design. Analysis of the results showed that the interactions between various factors were significant. Hence, a first-order linear model of the flotation response would not be accurate. The two-level three-factor design was expanded into a composite design in order to test the fit of a higher-order model. Data were treated to obtain an expression for flotation response as a function of the different variables, to predict the optimum reaaent levels at various slime levels, and also to determine the path of steepest ascent. Tests around the predicted optimum and along the path of the steepest ascent were done until a near-optimum region was obtained. Exploration of the nature of the response surface in that region established the actual location of the maximum response. The optimum amine level was found to be 0.20 lb of amine per ten of ore at all slime levels, while the optimum starch level varied as a function of the slime present. Computer access at the laboratory by means of a teletype terminal on a commercial time-sharing system enabled efficient and accurate treatment of experimental data. The efficiency of experimental investigations can be improved significantly by the use of experimental design and data analysis based on statistical principles. The common approach used in experimental research is to study a property of a system as a function of "one-variable-at-a-time". Several authors'-4 have pointed out the inadequacy and deceptiveness of this method. Results obtained for the effects of a variable on the measured response of the system using

Jan 1, 1970

By H. J. Modi, P. L. De Bruyn

IN recent years interest has been aroused in flotation rate studies both from a technical and a more practical aspect. With increasing fineness of grind becoming a necessity in treatment of low grade ores, difference:; in flotation rates of various size ranges will assume importance in the evaluation of overall recovery results. Theoretical analysis of flotation kinetics was initiated by Schuhmann,' who sought to define flotation rate of a given mineral and specified size range in terms of certain physical variables of the flotation system. Using as a basis for his analysis the bubble-particle encounter hypothesis previously advanced by Gaudin,' Schuhmann writes for the rate of flotation (R,.) of particles of average size x, Rx = PcPa(x) V F. [1] In this relation Pc and Pa represent, respectively, the probability of collision between particle and gas bubble in a given time interval and the probability of adhesion of particle to the bubble after collision. Rigorously speaking, the term PC does not have the significance of a probability factor, since it depends on the time interval and therefore can be numerically greater than unity. The term c(x) expresses the concentration of particles of an average size x in the flotation cell in weight per unit volume of pulp, and V denotes the total volume of pulp in the cell. The product, P,c(x)V, defines the frequency of particle-bubble collisl.on, and when it is multiplied by P,, the number of collisions per unit time resulting in successful adherence is obtained. The factor, F, measures the froth stability and is introduced because after fruitful bubble-particle contact some particles may still riot reach the froth launder. Coalescence of bubbles in the froth column or too short a bubble life could account for this effect. Schuhmann also introduced the concept of "specific flotation rate" (Q) to allow for the relative abundance of different mineral species in the flotation pulp. The specific flotation rate, having the dimension of reciprocal time, is defined as Eq. 2: Qx =Rx/c(x)v [2] and it also follows from Eq. 1 that Qx = PcPaF. [31 The theoretical aspects of flotation kinetics were also considered by Sutherland,3 who tried to improve Eq. 1 by expressing the probability factors in terms of such physical variables as particle radius (x), bubble radius (X), velocity of bubble relative to particle (v), the number of bubbles per unit volume of pulp (N) and the induction period (A) necessary for air-mineral adhesion. According to Sutherland's treatment, the rate equation, Eq. 1, transforms to R, = [3pX x v N] [sech2 (3 v ?/4 X) ] ?c(x) V [4] where the first term in brackets on the right-hand

Jan 1, 1957

By T. M. Morris, W. E. Horst

W. E. Horst—In regard to the flotation rate being described as "first orcler" for flotation of quartz particles below 65 p in size (or any size studied in this work) in this paper, it appears that the authors' conception of rate equations is not in agreement with cited references. A first order rate equation has as one of its forms the following: a In.=a/a-x=kt where a = initial concentration, a—x = concentration at time t, t = time, and k = constant. The constant, k, has the dimension of reciprocal time which is similar to the specific flotation rate, Q. described by Eq. 2 in the authors' article, as has been previously discussed by Schumann (Ref. 1 of original article). The plotted data presented in Fig. 4 of the article utilizes the specific flotation rate, Q (min.'); however, there is not adequate data given to indicate the order of the rate equation which describes the flotation behavior of the quartz system studied. Results from the experimental work indicate that the relationship between rate of flotation (grams per minute) and cell concentration (provided the percent solids in the flotation cell is less than 5.2 pct and the particle size is less than 65 p) is described by an equation of the first order (R, = k c+", n being equal to 1 in this size range) and the use of the first order rate equation does not apply. Similarly the relationship for other particle size ranges studied is expressed by equations of the second or third order depending on the magnitude of n. T. M. Morris—The authors are to be commended for the experiments which they performed. As they state in their discussion the concentration of collector ion In solution did change with change in concentration of solids in the flotation cell. Since for a given slze of particle, flotation rate increases with concentration of collector until a maximum is reached, the effect of concentration of particles in their experiments was to vary the concentration of collector ions. A collector concentration which insures maximum supporting angle for all particles eliminates the unequal effect of collector concentration on various sized particles and the effect of size of particles and concentration of particles upon flotation rate could be more clearly assessed. I believe that if the authors had increased the concentration of collector to an amount sufficient to attain a maximum supporting angle for all particles they would find that the specific flotation rate of particles coarser than 65 p would be constant with change in the concentration of solids in the flotation cell, and that a first order rate would apply to the + 65 as well as to the —65 p sizes. It might also be discovered when this change in collector concentration was made that the maximum specific rate constant would be shifted toward a coarser fraction than when starvation quantities of collector are used since this practice favors the fine particles and penalizes the coarse particles. P. L. de Bruyn and H. J. Modi (authors' reply)—The authors wish to thank Professor Morris for his kind remarks and for mentioning the influence of equilibrium collector concentration on flotation rate. With a collector concentration sufficient to insure maximum supporting angle for all particles, a first order rate equation may indeed be found to be generally applicable irrespective of size. Such a concentration would, however, lead to 100 pct recovery of the fine particles and consequently defeat the essential objective of the investigation to derive the maximum information on flotation kinetics. To establish absolutely the validity of any single rate equation for a given size range, the ideal method would be to work with a feed consisting solely of particles of that size range. Use of such a closely sized feed would also eliminate the possibility of the interfering effect of different sizes upon one another. The authors do not believe that increasing the collector concentration would shift the maximum specific flotation rate (Q) towards a coarser fraction. Experimentation showed Q to be independent of solids concentration for all particles up to 65 µ in size, whereas the maximum value of Q was obtained in the range 37 to 10 p. Professor Morris contends that the addition of starvation quantities of collector favors fine particles at the expense of coarse particles, but the reason for this is not entirely clear to the authors. The comments by Mr. W. E. Horst are concerned only with the concept of the term "first order rate equation." According to the usage of this term in chemical kinetics, time is an important variable, as is shown in the equation quoted by Mr. Horst. All the experimental results reported by the authors were obtained under steady state continuous operations when the rate of flotation is independent of time. To be consistent with the common usage of the "first order rate equation," it would be more satisfactory to state that under certain conditions the experimental results show that the relation between flotation rate and pulp density is an equation of the first order.

Jan 1, 1957

By U. N. Bhrany, J. H. Brown

The specifications of particle size and the size analyses of fine particulate materials are commonly presented without reference to the method of analysis. A review of the various sizing methods showed that not only numerous sources of error but also different definitions of size are inherent in the different methods of analysis. To demonstrate the magnitude of the differences, the size distribution of finely crushed quartz was determined by several methods and a critical comparison of the data was made. The experimental results show that appreciably different sizes may be indicated for one material depending on the method of analysis used. However, because the shape of the size-distribution curves determined by almost all methods was constant, a simple method of correlating the data can be adopted. Conversion factors, by which size measurements obtained by the various methods can be expressed in terms of screen sizes, are presented as one method of correlating the results. The size analysis and size specification for lump rock and particulate materials are commonly determined with sieves. With this technique, a readily reproducible measure of size can be obtained merely by duplicating the sieve and the method of sizing. For coarse materials, such as lumps of rock, this technique is simple and effective; and the effects of properties of the material such as shape can be readily understood. When very small particles are measured, however, problems arise. Small sieves are difficult to construct and maintain, and size separations become sensitive to the analytical procedure. For these difficult sieve sizes and for still smaller particles, other sizing techniques employing, for example, sedimentation, light extinction, and microscopy are available. Because these various techniques employ different size-dependent responses to establish size, it is appropriate to examine them and the results they yield to determine their relationships and their limitations. The 'size' of a lump of rock is not an absolute quantity, but rather a defined one. With sieves, for example, the size is defined by the screen aperture and no reference is made to the actual shape of the particle, yet only in the case of a regular body, such as a sphere, can the sieve size be related to the shape. With sieves only two dimensions of a particle can be suggested, for the sieve makes no allowance for the length of the particle passing through an aperture. Similarly, the size of a particle as measured by a microscopic technique need bear no relationship to the size as measured by sieves, although the two measurements may be related statistically. In fact, all size measurements are not only defined quantities, but the measurement actually used is an average that is controlled by the technique employed and, hopefully, reflects the property in question of the material of interest. Many papers have been presented that illustrate the accuracy of the various sizing methods, present the advantages of certain methods for certain applications, and describe the principles and technical backgrounds of the various methods. No attempt will be made in the present paper to review this work in detail. The purpose of the present paper is to examine the limitations of the various sizing methods, and to demonstrate experimentally the relationships between the sizes as determined by the various methods of analysis. It is hoped that by recognition of these limitations and relationships, errors in size specification and size interpretation will be avoided. REVIEW OF SIZING METHODS In specifying the size of a material, not only the data but also the method of measurement must be stated. For example, the size of the lump might be specified as its total volume, as its weight, as its maximum dimension, or as its minimum cross section; any one definition might be completely satisfactory for one problem, but not for another. In practice, size analyses follow four basic approaches and fortunately, the conditions that restrict each approach are known. These major methods include: 1) screen analysis, 2) direct measurement of particle dimensions, 3) determination of equivalent spherical size in response to fluid flow, and 4) specific surface determination. Each of these techniques has several variations and some new techniques are also available, but the limitations of the basic techniques are sufficient to permit at least a preliminary

Jan 1, 1962

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

By S. G. Dixit, A. K. Biswas

The flotation and adsorption behavior of ilmenite, monazite and zircon have been studied with sodium oleate as the collector and pH as the principal variable. The maxima in the flotation and adsorption properties of any of the above minerals fall within similar pH ranges. The bell shaped pH versus adsorption magnitude (r) curve is explained on the basis of collector concentration (Co and the concentration of hydroxyl ion (COH-) acting as the depressant. An equation of the type: 1 =KiCor~K2 Coh-/Coi-is proposed to account for the experimental data. The beach sand deposits along the sea coast in Southern India contain ilmenite, monazite, zircon, rutile and sillimanite as valuable minerals while quartz, garnet, shells and traces of hornblende form the gangue. A typical composition of the deposits is reported to be as follows:' Ilmenite 75%, Zircon 4-6%, Rutile 3-4%, Monazite 2 - 4%, Garnet 2 - 5% and the rest 8 -10%. Selective flotation of beach sand constituents has been reported by many workers.2-4 The fatty acid soaps have been invariably used as collectors. It is seen that all the valuable constituents of the beach sand are efficiently floated by soap collectors such as sodium oleate. In order to selectively float the beach sand constituents, it is necessary to use some depressants such as sodium silicate.3 The physicochemical parameters that govern the flotation of these minerals are yet to be studied in detail. In the present article, the findings on the parallel studies on the flotation and adsorption of the systems — ilmenite-sodium oleate, monazite-sodium oleate and zircon-sodium oleate — are being reported. In these correlative studies on adsorption and flotation of beach sand minerals, ilmenite (FeTiO3), monazite (Ce, Dy, Nd) PO4 and zircon (ZrSiO,) have been selected because they represent three important

Jan 1, 1970

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By V. Lessels, D. J. Buckwalter, D. H. Rose

A cyanide leaching process developed at Michigan Technological University was tested in a 12 to 24 tpd pilot plant. Flowsheet layout and equipment are described. Cyclic operation of leaching, copper precipitation by acidification, and regeneration of the cyanide leaching solution are discussed. Copper extraction and reagent consumption were as predicted by laboratory tests, and the process was proven to be technically feasible. The White Pine Copper Co., a wholly-owned subsidiary of the Copper Range Co., produces copper in the Upper Peninsula of Michigan. Production in 1965 amounted to 138 million pounds of metal. An expansion program now under way will increase this by approximately one half. The highly mechanized room and pillar mine produces 18,000 tons of ore per day, which is treated in a flotation plant. The concentrate is smelted in a reverberatory furnace, the matte is blown in converters to blister copper, and the blister copper is further refined to a uniformly high-quality Lake copper, which is 100% conductive and has a silver content of 25 to 40 oz per ton. The run of the mine ore averages 22.5 lbs of copper per ton with the ore mineral occurring in the form of chalcocite. The nature of the mineralization is such that the sand tailings average a little over 4 lbs of copper per ton. Intensive research has improved copper recovery in the flotation operation to some extent, but at the scale of present operation about 12,000 tons of sands containing over 48,000 lbs of copper go to the tailings pond daily. When the plant expansion is completed, the loss of copper will be somewhat greater. In 1959, the White Pine Copper CO, initiated a study of the recovery of copper in the sand tailings. Inasmuch as the flotation operation was considered to be optimized, a logical approach seemed to be leaching. For various reasons ammonia, ferric chloride, acid, and biological leaching were ruled out as impracticable. This led to a consideration of cyanide leach-

Jan 1, 1968

By S. F. Ravitz, S. R. Zimmerley

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951