Search Documents

This issue presents the first of several articles making up the Bump Symposium, which was held at the 1958 Annual Meeting of AIME. Other Symposium papers will appear in the September issue of Mining Engineering. THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump. The problem is extremely complex, and it cannot be over-emphasized that preventive measures, if they are to be successful, must be based on a thorough study of conditions in the individual mine. In western Canada, for example, the McGillivray mine, operating in a 9-ft seam at 2000 ft, has experienced severe bumps, but there have been no occurrences in the International mine, which operates in the same coal seam at 2400 ft, where the coal averages 17 ft thick. Differences in conditions governing the operation of these two mines are described in one of the following articles (see page 883). Again, most bumps in coal mines take place along pillar extraction lines, but at the Sunnyside mine in Utah they also occur a long way from active workings and sometimes in virgin territory. It is usual, too, for such failures to occur under fairly deep cover. But at Sunnyside, to cite only one instance, there have been disturbances along the main fault zone under less than 500 ft of cover. All too often conditions favorable to bumps are revealed only by actual mining—at Springhill No. 2 mine, drilling in roof and pavement strata disclosed a 60-ft sandstone bed after operations had started— and where extraction has advanced too far for preventive measures to be incorporated in the mining plan, districts have had to be abandoned. But in an era when premium ores are being rapidly depleted in the face of rising demands, abandonment is not easily justified. There must be systematic planning to eliminate coal mine bumps, insofar as this is possible. As in the Gary district of West Virginia (see page 888) much has been accomplished by planned operations based on known factors in bump control. But even this is not enough. Precise instrumentation is needed to indicate where bumps are likely to occur, and in both the U. S. and Canada stress analysis studies are being carried out with this object in view. These pages reveal the progress being made.

Jan 1, 1959

By K. K. Kohli, S. S. Peng, R. E. Thill

Introduction Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include: 17 longwall panels and 2 room and pillar sections. The data in each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages. Most subsidence surveys started with the first panel and ended with the second or sometimes, but rarely, the third panel. The first panel may be located in a virgin area but frequently it was adjacent to (on the tailentry side) a mined-out room and pillar section. It must be noted that all of the subsidence data is restricted only to the amount of vertical subsidence and that the horizontal displacement measurement was completely ignored. Primarily due to the fact that vertical subsidence is the most striking feature in a subsidence trough, which is mistakenly considered to be the only critical contributor to surface structural damages, and that a horizontal displacement survey is much more complicated and time-consuming.

Jan 1, 1981

[Admissions: B. M. Gottlieb, Chairman Edmond F. Egan K. Marshall Fagin John S. Fuller Edward E. Monteith T. A. Pollard Howard J. Ritts, Jr. Kenneth W. Robbins Harold E. Wright Advertising and Exhibits: Bernard F. Klein, Chairman Bob Diggs Brown R. E. Howard H. M. Krause, Jr. R. G. Parker Mrs. Evelyn R. Robertson]

Jan 1, 1961

By D. G. Mickle, H. L. Hartman

Hydraulic filling was probably first used as a means of ground support in 1864 in an anthracite mine at Shenandoah, Pa. In the nearly 100 years since that time it has gained widespread acceptance, but surprisingly little study has been made of the basic features of the process. The investigations that have been made primarily concern the design of preparation processes and transportation systems, while little attention has been paid to ensuring that the fill does its job adequately after placement. Both permeability and compressibility of fills have been studied in the laboratories of the Department of Mining at The Pennsylvania State University under the sponsorship of the Mineral Conservation Section, formed to promote efficient utilization of the state's resources. Results of these studies form the basis of this article.

Jan 11, 1961

United Engineering Trustees, Inc Engineering Foundation Engineering Societies Research Board Other Committees United Engineering Trustees, Inc. ARTHUR S. DWIGHT GEORGE D. BARRON J. V. N. DOER Engineering Societies Library Board ROBERT PEELS PHILIP W. HENRY GEORGE C. STONE JOSEPH E. POGUE The Engineering Foundation H. C. BELLINGER GALEN H. CLEVENGER J. V. N. DORR

Jan 1, 1929

The following tables showing the output of coal during the year 1913 have been secured y R. H. Morris, of Pocahontas, Alberta, Canada, for the use of the Committee through the kindness of John T. Stirling, Chief Mine-Inspector of Alberta. The principal mining districts are, Crow's Nest Pass, Calgary, Lethbridge, and Edmonton, the outputs from which were as follows: Tons Crow's Nest Pass 1,849,435 Calgary...: 627,461 Lethbridge ; 966,020 Edmonton 863,430 Total 4,306,346 Of this quantity there was exported to the United States, principally from the Crow's Nest Pass district, 138,201 tons of 2,000 lb., that being the ton used throughout the Province. This production consisted of lignite, bituminous coal, anthracite, coking coal and coal used in making. briquettes, as follows: Tons "Lignite coal" (lignitic?) 1,763,225 Bituminous coal 2,374,401 Anthracite coal 168,720 Coking coal 104,012 Coke produced 65,167 Briquettes produced 130,861 The only district in which coke was made is the Crow's Nest Pass district, and the entire product was consumed in Canada. The total number of persons employed is as follows: Above ground 2,231 Underground 5,837 Total 8,068 The per capita production was as follows: Tons of coal mined per employee 533 Tons of coal mined per underground employee 737

Jan 7, 1914

South Dakota State School of Mines, Rapid City, S. D. C C O'Harris,-President. A number of technical bulletins have been issued at the South Dakota State School of Mines but, unfortunately, most of them are out of print and as this directory is concerned only with available publications, the following are all that are now to be had Bulletin 11, A bibliography of the geology and mining interests of the Black Hills region (1917), no charge; 14, The geology, mineralogy, and scenic features of Custer State Park (1926), 40 cents plus postage on 1 lb ; 15, The Tertiary mineralization of the northern Black Hills (1927), charge, postage on 1 1b.; 16, The mineral wealth of the Black Hills t418 pages) (1929), 80 cents plus postage on 3 lb

Jan 1, 1933

Climax Molybdenum Co. has contracted with the Government to operate its property at Climax, Colo. at maximum capacity for five years. Substitution of synthetic lubricants, polyalkylene glycols and their derivatives, for petroleum products in certain industrial applications is yielding substantial savings in production costs and improved operation of mechanical equipment.

Jan 1, 1951

By D. Y. Geng, S. S. Peng

Surface subsidence of two longwall panels, one with a private residence and the other with an arch bridge, was monitored over a period of 1 to 1' ½ years. Surface subsidence data were analyzed in terms of zone of advance influence and delay angle of maximum subsidence velocity. The variational characteristics of both features coincide with the periodic weighting at the advancing longwall face. Surface heaving in the subsidence process can also be attributed to periodic weighting. It was found that residential damages occurred when subsidence velocity exceeded 4.5 mm/day (0.15 ft/day). The effects of locating structures on the panel center and near the gob edges are illustrated. The effect of mining on ground water was also discussed. Finally, methods of reducing structural damages are recommended.

Jan 1, 1984

By Ernest F. Burchard

PAGE. I. Introduction,........... 75 II. Outline of the Geology......... 76 1. Stratigraphy............ 76 A. Clinton Formation........ 77 2. Structure...........82 3. The Ore..........85 A. Character............ 85 B. Geographic Distribution....88 III. Local Descriptions........... 88 1. Birmingham District.......... 88 A. Topography and Its Relation to Industrial Development... 88 H. Distribution and Structure of Formations.... 89 C. Divisions of the Birmingham District. 95 Division A (Description of the Ore-Beds), . 95 Division B.........105 Division C.......... 106 Division D,..107 Division E,...........108 Division F........ 111 Division C.......... 112 D. Mining .Development.... 113 2. Northeast Alabama........114 IV. Possible Origin oF the Ore......... 119 V. Relation of Origin to Quality and Extent of Ore... 122 VI. Estimates of Ore-Reserves,......... 125 1. Method of Making Estimates......... 125 2. Data and Results....126 VII. Production and Consumption oF IRon-ORe,.... 132 I. Introduction. Brief and interrupted studies of the Alabama Clinton iron-ores have been made within the last four years by members of the IT. S. Geological Survey. Reports on the progress of this

Jan 1, 1910

By Rex E. Cheek, Donald E. Menzie

The fluid mapper, a model relatively new to the petroleum industry, was used to study the effect of various mobility ratios on the areal sweepout efficiency for two typical spacing patterns. The experiments indicated the areal sweepout for the five-spot pattern varied from 51.8 per cent at a mobility ratio of 0.093 to 89.1 per cent for a ratio of 24.4. In the direct line-drive pattern, the areal sweepout varied from 58.7 per cent at a mobility ratio of 0.089 to 92.0 per cent at a ratio of 24.8. The fluid mapper may prove useful to determine quickly the effective areal sweepout for any well spacing. INTRODUCTION The effect of the mobility ratio on the areal sweepout efficiency during primary depletion of a water drive reservoir and during secondary recovery operations has recently become more widely recognized The mobility ratio, M, is defined as: _ kjp (displaced fluid) k/u (displacing fluid) where k = effective permeability u = viscosity When the displacing fluid is miscible with the displaced fluid, the permeabilities are equal and the mobility ratio may be expressed as a ratio of viscosities: u (displacing fluid) u (displaced fluid) The mathematical analysis for calculating the areal sweepout efficiency with mobility ratio other than unity is quite tedious.5,11 An experimental method by using a potentiometric model2 in a step-wise manner and in using an X-ray shadowgraph model3,12 with continuous fluid flow has been published. Several types of models have been used to study oil and gas reservoir performance. These models may be classified as physical, electrolytic, potentiometric, X-ray shadowgraph, and fluid mapper. The X-ray shadowgraph and fluid mapper are models relatively new to petroleum engineering and have not been used extensively for specific applications. The theory of the fluid mapper indicates it may be adapted to a study of areal sweepout efficiencies for various mobility ratios as well as other complex problems in petroleum engineering. The use of the model and results obtained when using displacing and displaced fluids of equal densities but different viscosities are discussed. FLUID MAPPER DEVELOPMENT H. S. Hele-ShawV eveloped a fluid mapper model based on the hydrodynamic theory. This theory is that in the steady flow of a viscous fluid between horizontal parallel plates spaced a very small distance apart, the effect of viscous shear is of such magnitude in the vertical plane that the motion in the horizontal plane is practically undisbrted streamline flow. Techniques developed by Hele-Shaw were not expanded and no additional developments in fluid mapper models were forthcoming until A. D. Moore, University of Michigan, published a series of papers starting in 1949, which describe the construction of a flexible and inexpensive model'h nd the fluid mapper technique for the solution of certain problems.' The essential components of the fluid mapper as developed by Moore are::.ln 1. A base slab. made of dental stone (calcium sulphate and water). which is shaped to represent the prototype. 2. Plate glass slightly larger than the slab and spaced

Jan 1, 1956

By H. D. Yoo, M. R. Tek, D. L. Katz

The behavior of gas-storage reservoirs subject to water drive is investigated through analog simulation on an electronic differential analyzer. The simulation technique developed on an LM-10 computer permits the prediction of reservoir volume or pressure resulting from the movement of water in the surrounding aquifer. The method developed on the analog computer consists of setting up an appropriate transfer-function circuit and feeding the arbitrary time-varying boundary conditions as an input signal. The input may be specified as gas reservoir pressure, pore volume or the water flux. Several cases studied include an isolated gas reservoir on a limited aquifer, interference among three reservoirs adjacent to a common aquifer and the growth of gas-storage volume on an aquifer. It is concluded that the method developed on an electronic differential analyzer provides an excellent technique to simulate and investigate the behavior of gas reservoirs subject to water drive. The agreement between the reservoir performance as predicted from the simulation technique and as measured from actual field data is found to be better than the range usually encountered in predicting water-drive behavior. INTRODUCTION It is generally known that some gas-storage reservoirs are located on top of blanket sands of large extent, saturated with brine called aquifers. Because the volume of the body of water associated with aquifers is usually very large and water is compressible, the cyclic pressure variations encountered in normal storage service inevitably cause unsteady, compressible flow conditions in the adjacent aquifers. The solution to radial diffusivity equation for a limited aquifer for constant terminal conditions has been know111 since the early 1930's. The solution for the constant terminal conditions for an infinite aquifer was puhlished in 1949.2 The proldem of handling the unsteady flow of water through a porous medium with time-varying boundary conditions has been studied by many investigators through the use of graphical,3 digital4 computing techniques or on an R-C type of electrical analog called a reservoir analyzer.5 The digital computer performs a series of arithmetic calculations to superimpose the solutions of constant terminal conditions, while the R-C type of analyzer permits the simulation of the continuous medium by means of "lumped-cell" electrical resistance and capacitance elements based on finite-difference approximations. The graphical method is based on the convolution integral solution of the partial differential equalion. The purpose of the present study was to simulate the behavior of an aquifer on a general-purpose, electronic differential analyzer to obtain the influx of water or the change in pressure at the reservoir continuous1r and quickly. The use of the electronic differential analyzer was based on well known solutions for the constant terminal conditions already available in the literature.2,6-8 THEORETICAL DEVELOPMENT MODEL. The gas reservoir (R) is described in relation to an aquifer in Fig. 1. The permeability and porosity of an aquifer sand, the viscosity of the brine, and the compressibility of the brine and the formation are assumed to be constant. It further is assumed that the blanket sand is not thick enough to give appreciable vertical pressure distribution. The model in consideration is circular with radial geometry. The aquifer radius can be of limited or infinite extent. The gas-water interface is assumed to be fully segregated, and the displacement of the gas by

By F. C. Bond

SIZE of grinding media is one of the principal factors affecting efficiency and capacity of tumbling-type grinding mills. It is best determined for any particular installation by lengthy plant tests with carefully kept records. However, a method of calculating the proper sizes, based on correct theoretical principles and tested by experience, can be very helpful, both for new installations and for guiding existing operations. As a general principle, the proper size of the make-up grinding balls added to an operating mill is the size that will just break the largest feed particles. If the balls are too large the number of breaking contacts will be reduced and grinding capacity will suffer. Moreover, the amount of extreme fines produced by each contact will be increased, and size distribution of the ground product may be adversely affected. If the balls added are too small, grinding efficiency is decreased by wasted contacts that are too weak to break the particles nipped; these largest particles are gradually worn down in the mill by the progressive breakage of corners and edges. Ball rationing is the regular addition of make-up balls of more than one size. The largest balls added are aimed at the largest and hardest particles. However, the contacts are governed entirely by chance, and the probability of inefficient contacts of large balls with small particles, and of small balls with large particles, is as great as the desired contact of large balls with large particles. Ball rationing should be considered an adjunct or secondary modification of the principle of selecting the make-up ball size to break the largest particle present. Empirical Equation In 19521,2 the author presented the following emerical equation for the make-up ball size: B - ball, rod, or pebble diameter in inches. F = size in microns 80 pct of new feed passes. Wi - work index at the feed size F. Cs - percentage of mill critical speed. S — specific gravity of material being ground. D == mill diameter in feet inside liners. K - 200 for balls, 300 for rods, 100 for silica pebbles. Eq. 1 was derived by selecting the factors that apparently should influence make-up ball size selection and by considering plant experience with each factor. Even though Eq. 1 is completely empirical, it has been generally successful in selecting the proper size of make-up balls for specific operations. But an equation based on theoretical considerations should be used with more confidence and have wider application. The theoretical influence of each of the governing factors listed under Eq. 1 was accordingly considered in detail, as described below, and a theoretical equation for make-up ball sizes was derived. Derivation of Theoretical Equation Ball Size and Feed Size: The basis of this analysis is that the largest ball in a mill should be just sufficient to break the largest feed particle into several pieces, excluding occasional pieces of tramp oversize. In this article the size F which 80 pct passes is considered the criterion of the effective maximum particle feed size. The smallest dimension of the largest particles present controls their breaking strength. This dimension is approximately equal to F. As a starting point for the analysis it is assumed that a 1-in. steel ball will effectively grind material with 80 pct passing 1 mm, or with F- 1000µ or about 16 mesh. The breaking force exerted by a ball varies with its weight, or as the cube of its diameter R. The force in pounds per square inch required to break a particle varies as its cross-sectional area, or as its diameter squared. It follows that when a 1-in. ball breaks a 1-mm particle, a 2-in. ball will break a 4-mm particle, and a 3-in. ball a 9-mm particle. This is in accordance with practical experience, as well as being theoretically correct. Confirmation of this reasoning is supplied by the Third Theory of Comminution," which states that the work necessary to break a particle of diameter F varies as F. Since work equals force times distance, and the distance of deformation before breaka4e varies as F it follolvs that the breaking force should vary as F½ These relationships are expressed in Table I, with a 1-in. ball representing one unit of force and breaking a 1-mm particle. This establishes theoretically the general rule used in Eq. 1 that the ball size should vary as the square root of the particle size to be broken. Ball Size and Work Index: The work input W required per ton" varies as the work index Wi, and the

Jan 1, 1959

By E. C. Reed

Drilling activity in Nebraska during 1945 continued to decline slightly over that of the previous year. Eight tests for oil and gas were completed during the year, of which seven were wildcats and resulted in dry holes. The eighth test, an inside location in the Dawson field of Richardson County, yielded an initial production of about 3o bbl. per day with 86 per cent water from the Hunton formation. Five wells were drilling at the end of the year, two of which were wildcats. Two of the drilling wells were deepening operations in the Dawson and Falls City fields and the third was an inside location in the Falls City field, which appears likely to result in a producer. Most of the operations were in Richardson County but two wells were drilled in Dawes and Gage Counties and one each was drilling in Holt and Washington Counties at the end of the year. There were no new discoveries of oil or gas.

Jan 1, 1946

Jan 1, 1901

By E. K. Olson

Eagle Mountain mine of Kaiser Steel Corp. began production in 1947 when the direct shipping ore contained 51-56% Fe. The high grade, wide ore face and low stripping ratio ores were rapidly depleted and Eagle Mountain required processing plants for upgrading and more efficient mining equipment. During 1970-71 total annual pit tonnage averaged 56 million tons of material ranking the Eagle Mountain Mine as the fourth largest in the country. Ore production averaged 12.5 million tons requiring a stripping ratio of 3.5: 1. During this period mining activities were scheduled for a three-shift, seven-day operation. The present mining rate is about 30 million tpy on a two-shift, five-day schedule.

Jan 12, 1972

By E. E. Wahlstrom

The Harold D. Roberts tunnel, in Summit and Park Counties, Colorado, is a concrete-lined pressure tunnel finished to a circular cross section of 10.25 ft diam. The tunnel is 23.3 miles long and is designed to transport water for domestic use by the City and County of Denver from reservoir storage at Dillon to a tributary of the South Platte River at Grant. The tunnel passes beneath the Continental Divide at the crest of the Front Range and intersects rocks of diverse types and origins and geologic structures of extreme complexity. Geologic investigations preceded and were continued during construction and contributed materially to the safe and economical advance of the tunnel headings. Geological data obtained and evaluated during construction include plans and sections on a scale of 1 in. to 50 ft, rock temperatures at 2000-ft intervals, records of progress related to geology, records of ground-water conditions, summaries of the use of steel and timber supports, and summaries of grouting operations. Adverse conditions required use of steel and timber supports for 71.74% of the total length of the tunnel. Most supported sections reached a condition of equilibrium within a few hours to a few months after being excavated, and the concrete lining serves chiefly to provide an additional safety factor and to provide necessary hydraulic characteristics to the tunnel. Efforts to attain a maximum rate of advance of the tunnel headings necessitated use of more steel and timber supports than would have been required in a less accelerated tunneling operation. This report summarizes geologic investigations prior to and during construction of the Harold D. Roberts tunnel in Summit and Park Counties, Colorado (Fig. 1) and analyzes the tunneling operation as it is related to the various kinds of geologic conditions encountered in the tunnel. The tunnel is concrete lined to a circular cross section of 10.25 ft and is designed to transport 788 sec ft from reservoir storage at Dillon 23.3 miles along a dog-leg course passing under the Continental Divide to outlet and control works at Grant, Colo. The primary purpose of the tunnel is to augment the domestic water supply of the City and County of Denver, but plans include provisions for power generation at the outlet portal at a future date. Location of the tunnel was made after extensive preliminary geologic and engineering investigations by the Board of Water Commissioners of the City and County of Denver, and the U.S. Bureau of Reclamation. In 1946 the Board of Water Commissioners started tunnel driving on a limited scale from the east (outlet) portal and by 1955 had completed 9986 ft of tunnel. An urgent need for additional sources of water supply required acceleration of the tunneling operation, and, in 1955, Tipton and Kalmbach Inc. of Denver were assigned the responsibility of reviewing the project and preparing plans and specifications for the tunnel and appurtenant features. Additional geologic studies were made, and the geology of several possible alternate tunnel lines were compared before determining that the tunnel should be driven along the course previously adopted by the Board of Water Commissioners. On July 12, 1956, a contract for construction was awarded to Blue River Constructors Inc., a combine

Jan 1, 1962

By M. H. Caron

BASIC U. S. Patent 1,487,145 on ammonia leaching of nickel ores was issued to the author on March 18, 1924. Equivalent patents in other countries were obtained later. The Dutch Syndicate Brikcarbo became interested in the process in 1935; and a couple of years later the late Dr. H. Foster Bain sent samples of Surigao laterite iron ore to Delft and witnessed tests made there on this material for the Philippines Commonwealth. As a result, the author was asked in April 1940 by Dr. Bain to go to the Philippines to erect and take charge of a pilot plant for the process. The World War prevented carrying out this proposal. The Dorr Co. also became interested in the process at about the same period. The investigations by the Freeport Sulphur Co. on the process as applied to the Cuban nickeliferous laterites, which resulted in the Nicaro enterprise, and the results of this operation have been well described elsewhere.1,²,³,4,5 This Nicaro plant was, in operation for almost two years, and during this period produced about 10 pct of the world nickel production from laterites containing 1.35 pct nickel. This plant and its operation were war measures and, in view of this, activities were suspended in April 1947. The results obtained fully demonstrated the technical feasibility of the process and its economical aspects on a commercial scale. In this respect, it should be understood that it is probable that improvements may be made by further development, and that there are possibilities for advantageous application of the process to garnierite and similar ores with higher values in nickel than the laterite iron ores at Nicaro. While the articles cited above have given a certain amount of information, no general article containing all the important process data has been pub- lished. Since the process is of more than local interest, a fuller knowledge of the fundamental and practical factors of the method may be welcome to those interested in this new field of metals technology. The author, accordingly, takes pleasure in submitting this article to the AIME as it represents in a condensed form the results of many years of research. The brief outlines of the fundamental and other factors and the explanation of observed phenomena are presented with as little discussion of details as possible, consistent with clarity. It is a special satisfaction to the author to make some contribution of his own in return for the benefits of the many valuable publications issued by the Institute during his thirty years of membership. Ores Adapted for Ammonia Leaching: All nickel and cobalt ores which originate from weathering of peridotites or similar basic rocks having sufficient values are suitable for treatment by the ammonia leaching process after a preliminary reduction under proper conditions. The formation of these deposits was probably as follows: In the course of time the basic rocks were attacked by atmospheric agencies; MgO and SiO2 were gradually leached out, and secondary nickel minerals formed, such as garnierite, a hydrated silicate of nickel and magnesia. These secondary products are, however, not stable. They decompose in a further stage of weathering and ultimately only a relatively small residue of insoluble oxides remains, known as laterite iron ore with a small nickel content and very little cobalt. Under these mantles of laterite, richer nickel values may be found, usually indicated by the occurrence of garnierite. The more the ore is disintegrated by nature, the higher the iron content and the better the nickel extractions that may be expected therefrom. Table I shows extractions that may be expected from different types of ores, assuming treatment of -200 mesh products and that all precautions have been taken for obtaining maximum extractions. As for the distribution of the various nickel minerals and compounds that may be present, great variations may occur from locality to locality as well as vertically in a deposit. From such "run of

Jan 1, 1951

Jan 1, 1906

By William H. Callahan

"For his exceptionally successful career as a geological mentor, for his ore-finding skills, and particularly the discovery of the Central Tennessee Zinc District and for his lecture, 'Prospecting in the USA-Promise and Problems.' " Recipient of the 1982 D.C. Jackling Award

Jan 1, 1983