Search Documents

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

By F. Wartenweiler

Much has been written on milling and cyanidation as practiced on this gold field, therefore the purpose of this paper is to record its development only briefly and to describe in more detail the contemporary state of the science and art of this branch of metallurgy. It is a pleasing task, because a steady evolution is to be recorded. Definite trends influenced the development. Some have the stamp of original thought and observation; many have been achieved from a logical sequence of planned experimentation and research; while others have resulted from the drive of sheer necessity. The large scale of operations and capital outlay has compelled conservative progress. Banket ORe For a better understanding, a review of the characteristics of the ore may not be out of place. The Witwatersrand gold ore is named "banket" from the similarity of the oxidized outcrop ore to the Boer almond cake of that name. The inter bedded orebody is commonly called "reef." It is a conglomerate composed of various sizes of pebbles, principally non-gold-bearing white quartz, which constitute about 70 per cent of the bulk, within a matrix of cementing material consisting of fine-grained quartz, sericite, chlorite and chloritoid and containing the precious metals and mineral sulfides. Argillaceous components in the mil pulp may be as high as 32 per cent. Of the sulfide minerals, pyrite and pyrrhotite are predominant. Most base-metal sulfides are present, but sporadically and generally only found in highly concentrated mill products. In the latter, osmiridium is recovered in varying amounts; from 1 oz. in 3000 tons to 1 oz. in 10,000 tons of ore. Most of the oxidized ore has been mined, so milling is confined principally to the sulfide ore. A typical analysis of sulfide ore is: silica (SiO2), 86.76 per cent; pyritc (FeS2), 2.75; ferric oxide (Fe2o3), 2.65; alumina (Al2o3), 6.91; lime (CaO), tr.; magnesia (MgO), 0.70; sp. gr., 2.7. Milling grade at present price of gold (137 shillings per ounce) varies from 3.5 to 8.5 dwt., with one mine milling ore as high as 16 dwt. The

Jan 1, 1935

Members whose deaths were reported from Apr 9, 1921 to Apr 7, 1923 Elected Died 1876 ABADIE, E R. 1923 1906 ADAMS, ARTHUR K 1920 1902 AHLES, ROBERT L 1921 1876 Akerman, Richard 0000 1884 ALEXANDER, CURTIS 1921 1918 ALLEN, CARL A 1923 1880 ALMY, WILLIAM F 0000 1893 AMSDEN, 0. B 1923 1917 ARGALL, P. H 1922 1917 ARNOLD, E C 1921 1914 ASANO, K 1921 1920 AUGUSTINE, ALBERT BEARSS 1922 1906 BAIRD, GEORGE A 1921 1921 BALDWIN, GEORGE P 1922 1920 BASKERVILLE, CHARLES 1922 1915 BENSEL, J A 1922 1890 BENSON, A J 0000 1912 BEST, WILLIAM NEWTON 1922 1892 BILHARZ, OSCAR M 1923 1890 BLACKSTONE, RICHARD 1922 1921 BLOOM, GEORGE BARNETT 1921 1905 BOSTWICK, WILLIAM A 1922 1884 BRANNER, JOHN C 1922 1920 BRIDGE, SAMUEL D JR 1921 1893 BROWNE, ARTHUR, 1922 1871 BUCK, STUART M 1921 1897 BURGER, C C 1922 1882 BURT, CHARLES S 1921 1921 BUTZ, Louis N 1922 1917 CAMPBELL, DONALD G 1921 1915 CAPLES, JAMES WATTS 1919 1892 CARLETON, JAMES G 1922 1914 CARUTHERS, A WAYNE 1922 1911 CHASE, FRED M 1921 1892 CLEMENT, F H 1922 1922 COAN, WALTER ERLING 1923 1872 COGSWELL, WILLIAM B 1921 1881 COLVIN, VERPLANCK 1920 1882 COOLIDGE, WALTER G 1922 1907 CORKILL, FREDERICK 1922 1912 COX, Guy H 1922 1883 CUNNINGHAM, JAMES S 1921 1873 DAGGETT, ELLSWORTH 1923 1916 DAULTON, THEODORE M 1921 1888 DICKERMAN, ALTON L 1921 1902 DIEFFENBACH, H M 1921 1911 DUNSTAN, SIMON P 1920 1917 DYNAN, ALAN E 1922 1920 EASTWICK, THOMAS H A 1922 1876 EDWARDS, J WARNER 1921 1914 ELDER, ROBERT B 1923 1885 EMMONS, ARTHUR B 1922 1911 ENGEL, GEORGE W 1920 1887 FERNOW, B E 1923 1879 FIRMSTONE, H1922

Jan 1, 1923

PAST AND PRESENT CHAIRMEN OF DIVISIONS Institute of Metals Iron and Steel Mineral Industry Industrial Minerals Year Division Petroleum Division Division Coal Division Education Division Division 1918 W. M. CORSET 1919 " 1920 W. H. BASSETT 1921 " 1922 W. B. PRICE RALPH ARNOLD 1923 E. DEGOLYER 1924 G. B. ELLIOTT 1925 F. JULIUS FOHS 1926 P. D. MERICA 1927 11 JOHN. M. LOVEJOY 1928 S. SKOWRONSKI A. W. AMBROSE RALPH H. SWEETSER ' 1929 " J. B. UMPLEHY G. B. WATERHOUSE 1930 ZAY JEFFRIES C. V. MILLIKAN W. J. MACKENZIE HOWARD N. EAVENSON 1931 SAM TOUR C. E. BEECHER F. M. BECKET 1932 C. H. MATHEWSON EARL OLIVER F. N. SPELLER THOMAS G. FEAR C. H. FULTON 1933 T. S. FULLER W. E. WRATHER JOHN JOHNSTON ELI T. CONNOR " 1934 J. L. CHRISTIE H. D. WILDE, JR. L. F. REINARTZ " T. T. READ 1935 W. M. PEIRCE HARRY H. POWER A. B. KINZEL JOHN T. RYAN SAMUEL H. DOLBEAR 1936 E. H. DIX, JR. HALLAN N. MARSH C. E. WILLIAMS EUGENE MCAULIFFE WILLIAM B. PLANK OLIVER BOWLES 1937 A. J. PHILLIPS M. ALBERTSON FRANCIS B. FOLEY J. B. MORROW " CHESTER A. FULTON 1938 R. F. MEHL G. B. CORLESS J. T. MACKENZIE PAUL WEIR FRANCIS A.THOMSON J. R. THOENEN 1939 R. H. LEACH W. H. GETS J. HUNTER NEAD C. A. GIBBONS " M. M. LEIGHTON 1940 E. M. Wise T. V. MOORE F. T. SISCO C. E. LA WALL W. R. CHEDSEY W. M. WEIGEL 1941 D. K. CRAMPTON E. A. STEPHENSON C. H. HERTY, JR. JULIAN E. TOBEY " PAUL M. TYLER 1942 CARL E. SWARTZ HARRY P. STOLZ E. C. SMITH NEWELL G. ALFORD A. F. GREAVES-WALKER B. L. MILLER

Jan 1, 1943

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By R. H. Lynn, T. C. Craig

During the year 1933, in the Texas Panhandle, 113 oil wells were completed, adding 33,337 bbl. to the daily potential of the field. The field potential on Jan. 1, 1933, as determined by the Texas Railroad Commission, was 149,260 bbl., with a daily allowable production of 41,000 bbl. The potential was raised gradually, until on July 16, 1933, it reached 155,344 bbl. with a daily allowable of 55,000 bbl. This potential and allowable was maintained over a period from July 16, 1933, to Sept. 8, 1933, when the potential was reduced to 136,893, with a daily allowable of 43,727 bbl. Since Sept. 8, 1933, there has been a gradual increase, until on Jan. 1, 1934, the field potential reached 159,740 bbl. with a daily allowable of 42,000 bbl. Of this amount 26,429 bbl. arc "marginal oil" and 2682 bbl. are exempt on account of water. Deepening of Wells During the year 64 wells were deepened, increasing their total oil production 9631 bbl. per day. Of this amount the Gray County granite wash contributed 9256 bbl. from 57 wells. It has been found in many places that the granite wash carries an additional oil pay from 50 to 75 ft. below sea level. The majority of the wells that were .drilled during the early development in Gray County encountered their oil above sea level. When the wells producing from the upper horizon have become unprofit-

Jan 1, 1934

By Henry J. Sandri

ACQUISITION JUSTIFICATION There are many reasons why companies consider acquisitions as a means to expand their operations. Some wish to reduce the impact of business cycles on their businesses. Others seek firms within the same industry for expansion and increased market share. Still others diversify in order to avoid takeovers. Whatever the reasons or justification, an evaluation of an acquisition candidate should be systematic and thorough. To many financial managers the concept of a systematic acquisition evaluation indicates the need for a regular set of evaluation criteria. While these are available from numerous sources, one basic parameter frequently overlooked is the application of these criteria to an industry which is different from the acquirer. This becomes particularly important when evaluating firms within the mineral industry. The mineral industry is significantly different from other industries to require different valuing techniques. • This paper will present a number of reasons why an acquisition candidate in the mineral industry should be evaluated differently from other acquisitions, including by other mineral firms. Additionally, this paper will review the most appropriate means of valuing a mineral firm. • Firms considering the acquisition of a mineral firm should understand the nature of the industry before ever making a tender offer. Some of the general considerations include the following: • Level of Capital Intensity: In the mid-1980's the start up cost for a gold mine has been between 20-200 million dollars and 500-1,500 million dollars for a bauxite operation. • Global Nature of Competition: Except for certain industrial minerals, most minerals and metals are traded worldwide and many on national exchanges, such as COMEX. • Start-Up Time: Many mining operations in developed and developing countries have long lead times, 7 to 10 years in some cases, prior to the start-up of production. • Long Term Nature of Investment: For most mineral operations payback usually occurs at least 7 years after production has started. Additionally, many mining operations will continue producing for 80-100 years. • High Level of Risk: The number of factors that a mining firm cannot control such as grade, volume, world supply and demand, plus the long payback periods tend to classify mineral firms at a higher than average risk compared to other investments. • Cyclical Nature: The mineral industry is cyclical in nature, experiencing long troughs and explosive peaks, thus making timing a critical issue. • Labor Intensive: Even with the large capital requirements needed to operate a mine, most mines are labor intensive in proportion to their capital equipment. • Location: Obviously, the nature of this industry requires operators to work in difficult locations, frequently far from civilized localities, in poor weather conditions and without proper supply and distribution infrastructure. One of the most important considerations is an understanding of asset replacement and asset value. Unlike manufacturing concerns, firms in the mineral industry are working toward the elimination, through depletion, of their asset base. Product flexibility is not available to a mining operation. A mineral firm basically has two options as its resource base is depleted: 1) replace the asset with new production, or 2) deplete the asset and close down operation, as in the South African gold mining model referred to later in this paper. An understanding of the

Jan 1, 1985

By W. A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into watercourses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appro-priative water titles. But by far the most profound impact on western water law was made by the gold-seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.1 They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.' In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State."" Rules of the California mining camps were based on two essential principles: 1) priority in discovering claims and appropriating water by diverting it from streams and putting it to use, and 2) diligence in working claims and applying water in mining. The customs so developed, which were copied in mining areas of other states and territories, were enacted into law in one western jurisdiction after another. They form the basis of what is called the arid-region doctrine of prior appropriation of water, which received the attention of Congress in legislation recognizing and protecting appropriations of water for mining, agriculture, and other purposes on the public domain.' In several western states a great number of water cases decided in the early years involved relative rights to the use of water for mining purposes or for milling connected with mining." The miner's inch, the customary unit for measuring water in the mining camps, is still used in various western communities, although its relation to the cubic foot per second varies from one area to another. Undoubtedly, the miners of a century ago made the major contribution to the appropriation doctrine as it is now recognized and applied throughout the West. What inspired the California gold-seekers to develop these principles? Thoughtful writers have pointed out that their regulations and customs were strikingly characteristic of much earlier mining enterprises in the Old World.D It is said that the right of free mining and free use of flowing water therefor —so similar to the California conditions and practices—-was a part of the customs of Germanic miners in the Middle Ages, that it spread from middle Europe to other countries and colonies, and that the doctrine of prior appropriation was widespread in the important mining regions of the world. Certainly the Forty-niners came to California from many countries. It does not tax the imagination to consider that they may have brought with them some knowledge of the old Germanic customs and applied this knowledge in their new environment. RIGHTS TO USE OF WATER IN GENERAL In the West, rights to the use of water of watercourses fall into two categories—appropriative and riparian. The doctrine of prior appropriation is recognized in each of the 17 western states. The riparian doctrine is recognized concurrently with the appropriation doctrine in some of these states but has been abrogated in the others. The riparian doctrine prevails generally throughout the East, although there is now considerable interest in developing something else. Generally speaking, the appropriation doctrine has been highly developed in the West, whereas the principles of riparian doctrine have been comprehensively established in only a few states throughout the country. The subject of water rights is a big one. Space permits no more than a brief discussion of aspects that bear upon the title of this article. RIGHTS OF PRIOR APPROPRIATION Fundamental to the doctrine of prior appropriation is the principle first in time, first in right. Although in some states there are statutory exceptions. the original and still generally prevailing rule is that the first one who initiates a right to divert and use water of a stream, and who completes his undertaking with reasonable diligence, acquires thereby the first right of appropriation of the specific quantity of water involved. Each succeeding right in point of time is junior to all earlier rights but senior to all later ones. The practical effect of this priority system is that when the water supply is not enough for all, the earliest rights must be fully satisfied before any water may be taken by those later in time. Acquirement of Appropriative Rights: Each of the 17 western states has a statute under which water may be appropriated pursuant to a prescribed procedure. Generally, the first step to be taken by the intending appropriator is to file application in the office of the State Engineer for a permit to make the appropriation. In most but not a11 states, valid ap-

Jan 1, 1961

By Ichiro Ito

At present, in Japan, the application of in-place leaching technique to the mined-out stopes has been carried out at two copper mines in a comparatively large scale. These mines are the Kosaka mine and the Tsuchihata mine, both are situated in the north-east district of Japan. At first, the author would like to tell about the in-place leaching operations and their results at these two mines. Then, the problems involved in the application of in-place leaching technique to the Japanese metal mines and the possibility of the future development of this technique in Japan are referred, too. Next, as to the research works, the author would like to explain briefly about some of the important results obtained in the recent studies on in-place leaching as well as on bacterial leaching in Japan.

Jan 1, 1976

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

Total U.S. mineral production reached an estimated $17.8 billion for 1960, 4 pct above 1959 and second only to the record high of $18.1 billion established in 1957. As a group, metals achieved a rise from $1.6 billion in 1959 to $2.0 billion this year, an increase of 28 pct. Similarly the value of nonmetallic production including fuels (i.e., natural gas, petroleum, natural-gas liquids, asphalt and related bitumens, carbon dioxide. anthracite. bituminous and lignite coal, peat, and helium) rose from $15.5 billion in 1959 to approximately $15.8 billion in 1960. However, this 2 pct increase in the total value of non-metallic production was due to an increase in the value of the fuels ($11.8 billion in 1959 to $12.2 billion in 1960) which offset a drop in value of the other nonmetallic minerals ($3.7 billion in 1959 to $3.6 billion in 1960).

Jan 2, 1961

By Milton E. Wadsworth, Edward M. Eyring

BETTER understanding of solid surfaces and their associated adsorption products is of both academic and practical value. The study of detergents and their behavior in cleaning surfaces is fundamentally related to the nature of the products adsorbed and their ability to compete for certain surfaces. Similarly in flotation, the nature of the adsorbate before and after adsorption is basic to clear understanding of the process. The recently developed pellet technique1,2 employing infrared spectroscopy provides a powerful tool for the study of solid surfaces. Absorption bands, which are infrared-active, may be observed for adsorbed products. Also any changes in the surface substrate that occur as a result of adsorption may be detected by means of differential spectra. In applying the pellet technique to solids of large surface area, French and his coworkers3 have surveyed the adsorption of organic flocculants on clay minerals, oleic acid on fluorite, and ammonia on cracking catalysts. Recent work on application of differential infrared spectroscopy to the study of solid surfaces' has demonstrated that the difference between a sample and a reference can be obtained with double-beam instrumentation. In this way displacement of surface products, adsorption of new products, and differences in the substrate, if any, may be detected. Experimental Procedure: Potassium iodide pellets were used in this study, prepared from recrystallized analytical reagent grade KI. Grinding was carried out in a Fisher mechanical agate mortar. Two-gram plates containing the solid under study were pressed in a special evacuated die constructed in the laboratory at the University of Utah." Concentration depended on the solid in question. Zinc sulfide and willemite are sufficiently transpar- ent in the infrared region for concentrations as high as 20 mg of mineral in 2g of KI to be used. Zinc oxide is even more transparent, permitting concentrations as high as 60 mg in a 2-g plate. For non-differential operation, however, much lower concentrations (2 to 10mg/2g KI) had to be used. Spectra were obtained on a Per kin-Elmer 21 double-beam recording infrared spectrophotometer. A sodium chloride prism was used giving a spectral range of approximately 2 to 15 v wave length. For differential runs a resolution of 1000 was used and the scanning speed was controlled commensurate with instrument response. The response was checked continuously and each spectrum was repeated several times. For nondifferential runs a resolution of 927 was used. Zinc oxide used was analytical grade oxide fume. The zinc sulfide was precipitated from solution with analytical grade zinc sulfate and sodium sulfide. The precipitate was washed and centrifuged several times and dried. Before use the precipitate was washed in dilute HCl and then treated with saturated NH4Cl to remove any bulk oxides and sulfates. X-ray patterns of the precipitate were comparable to that of the natural mineral sphalerite. The precipitate was much more satisfactory than finely ground natural ZnS because of its very large surface

Jan 1, 1957

By Mehl, Robert F.

IT has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relation-ship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solu-tions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available .2 Related to this latter class

Jan 1, 1934

By M. Bevis, E. O. Fearon, P. C. Rowlands

Fe-Ni and Fe-Ni-C martensite specimens have been deformed in compression at room temperature and the habit planes of operative deformation twins determined by two-surface optical trace analysis. The full orientations of the martensite crystals were determined from divergent X-ray beam diffraction patterns. The experimental results are in excelled agreement with predicted twinning modes. In particular, the habit planes of some deformation twins in bcc martensites are consistent with a "Type XI compound'' twinning mode with Kl, Kz, 71, 77~ elements given by {5, 8, 11) {ioi}, (33) (ill) Tetragonal derivatives of this mode are operative in bct martensites. UnUSUAL deformation twinning modes have been reported by Richman' to occur in Fe-Ni-C martensites with bcc and bct structures. The twin habit planes were determined by single-surface trace analysis (pole locus method) and the remaining twinning elements were determined from the geometry of twin-twin intersections. The indices assigned to the observed habit planes are (3 101, "(089)" and "{0, 1,13)" or "{1,2,7} ", and only in the first case do the twinning elements correspond to a predicted twinning mode. This is mode 1.4 in the paper by Bevis et al. The results presented in Ref. 2 indicate that previously unpublished bcc and bct modes should be operative in preference to the (130) mode and anomalous modes reported by Richman. In view of these results and the uncertainties involved in determining habit planes from single-surface trace analysis and twinning elements from twin-twin intersections5 a two-surface trace analysis of deformation twins in Fe-Ni and Fe-Ni-C martensites has been carried out. EXPERIMENTAL PROCEDURES Two alloys with compositions Fe-23 pct Ni-0.6 pct C and Fe-30.4 pct Ni were prepared from 4N pure materials by induction melting under a vacuum of 10"5 mm Hg. The alloys were homogenized at 1350'~ for 5 days. Both of these alloys are austenitic at room temperature with M, temperature - — 50"C. The aus-tenite grain size of the Fe-Ni-C alloy was approximately 300 to 400 p. The Fe-Ni alloy was remelted in a vertical tube furnace and the melt lowered slowly from the hot zone of the furnace to produce s ingle -crystal austenite specimens. Specimens approximately 10 by 5 by 5 mm were cut from the ingots and quenched to various temperatures below the Ms temperature. The specimens were elec-tropolished in a 10 pct perchloric acetic electrolyte before being deformed in compression at room temperature. Martensite plates which exhibited profuse deformation twinning were selected for analysis and the specimen polished on a second surface such that the two surfaces which contained the martensite plate enclosed an obtuse angle of approximately 145 deg. The specimens were then electropolished to reveal the traces of the deformation twins on both surfaces. The full orientations of the martensite crystals were determined using a divergent X-ray beam technique (Kossel line technique) employing an AEI SEM2 electron probe microanalyzer. Details of this technique which include a detailed description of the Kossel camera attachment to the microanalyzer used in the present experiments have been discussed elsewhere.3 Only additional details relevant to this investigation are discussed here. The specimens were mounted with one surface normal to the incident electron beam as illustrated schematically in Fig. 1. The martensite plates to be analyzed were located using the normal scanning equipment of the microanalyzer. The position of the electron beam and hence the position of the source of divergent X-rays generated within the crystal could be located to within 1 p. Exposure times of approximately 8 to 10 min were required for back-reflection Kossel patterns and it was found that useful diffraction patterns could be obtained consistently from heavily deformed martensite plates. A reference line (carbon contamination mark) produced on the two surfaces of the specimen by scanning the electron beam in a direction having a known relationship with the reference !ine in the X-ray camera enabled the full orientation of the crystals to be determined. Martensite plates with widths as small as 8 p could be oriented using this procedure. The Kossel line patterns were interpreted using the charts developed by Rowlands and ~evis~ as generally

Jan 1, 1969

By Richard H. Jahns

GRANITIC pegmatite deposits are the chief source of commercial feldspar, sheet mica, beryllium, tantalum-columbium, and lithium minerals, and certain types of kaolin. They also have yielded significant quantities of cassiterite, gems, scrap mica, molybdenite, tungsten minerals, uranium-thorium and rare-earth minerals, and zircon, either directly or as the sources of placer deposits. The output from pegmatite mines in the United States is small as compared to other mineral products in terms of bulk or value, and much of it comprises minor metals and nonmetals. Nevertheless, pegmatite minerals play a vital part in domestic industrial economy, particularly in the ceramic and electrical industries. Numerous special purpose uses also are important, even though they require small quantities of raw materials. Never was United States dependence upon pegmatite mining more clearly emphasized than during World War 11, when greatly expanded demands and uncertainties of foreign sources of supply caused much concern. Such commodities as beryl, tantalite, and sheet muscovite remained high on the critical list for months at a time, and for some minerals there was a real struggle to achieve and maintain a favorable ratio of supply to demand. Satisfactory stock piles of certain sizes and qualities of sheet mica, for example, were not built up until late in 1944, when wartime requirements already had begun to level off or even to decrease. Production of all the strategic pegmatite minerals from domestic deposits during World War I1 constituted only 10 pct or less of the total domestic consumption of these minerals, but the importance of this contribution should not be minimized. Domestic production often represented the difference between increase and further reduction of existing stocks of commodities already in seriously short supply, and in the early stages of the war it was the only assured source if imports were cut off. During the recent war period, the U. S. Geological Survey carried on a program of pegmatite studies in the New England and Southeastern States, in the Black Hills area of South Dakota, in the Rocky Mountain region of Wyoming, Colorado, and New Mexico, and in various parts of Washington, Idaho, Utah, Nevada, Arizona, and California as shown in Fig. 1. Several papers and reports already have appeared as an outgrowth of this work,'-= and others are in preparation. This paper outlines some results of data obtained by the writer during the period 1942 to 1946, when he was engaged in studies of pegmatites in the Southeastern, Southwestern, and Rocky Mountain States. Beryllium Minerals Beryl is the present commercial source of beryllium metal and beryllium compounds, which are used in ceramics, in the preparation of X-ray tubes and fluorescent lamps and screens, in special processes of paint and textile manufacture, and in the optical systems of some electrical instruments. The metal also is used in nuclear physics, chiefly as a source of neutrons. Beryllium is alloyed with aluminum for certain light-metal uses and is a constituent of some nickel and iron alloys. Currently the chief demand, however, is for copper-base alloys, which are exceptionally resistant to fatigue and wear, are responsive to hardening treatments after

Jan 1, 1952

By Plato Malozemoff

Our young, technically oriented people today are entranced by the space program, by physics that unlocks the secrets of nature, by electronics, and by other new technologies. The mining industry seems to be their last choice. Enrollment in mining schools is dropping and so is the interest of our great universities in mining curricula. The image of the mining industry appears to be one of being conservative, nonprogressive, resistant to change, and lacking in excitement and challenge. I submit that this public image is wrong. While the initial development of mines is usually slow and seemingly plodding, the problem of solving the imponderables of nature-the ore emplacement, its structure and physical characteristics, its response to recovery processes, and its probable ultimate profitability-is stimulating to the most acute and searching of minds and requires careful application of a combination of many technologies. The paths to obtaining the desired results must be within the bounds of reasonable expenditures in the early stage of development when risks are still high, and this financial discipline is a further stimulus to the imaginative search for the right answers.

Jan 6, 1968

By M. D. Cooper

FOr the purpose of obtaining some first-hand data in regard to the shooting clown of coal in bituminous 'nines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6,020 shots were fired by him during this period. All of the work was clone in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Co. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut.

Jan 1, 1917

By T. M. Chance

THE term "low-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as 1 ½ per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low sulfur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, With few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 ½ per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous dis-tricts, it has been necessary to turn to the areas of higher-sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.-Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout

Jan 8, 1919