Search Documents

By S. Weissmann, P. R. Swann, D. F. Wriedt

The sizes and density of precipitates in an intemally oxidized 0.19 wt pct Al-Ag single crystal have been determined by low-angle X-ray scattering and by transmission electron microscopy . The correlation in particle sizes measured by the two techniques is reasonably good. For an oxidizing temperature of 800°C the particles were found to INTERNAL oxidation of dilute alloys of aluminum in silver produces an oxide which has an excess of oxygen compared to Al2O3.' It is believed that the excess oxygen is an indication of the small sizes of the oxide particles. Depending upon the particular model chosen for the oxide structure, the size of the o-A1 particles can be calculated as a function of the oxygen-to-aluminum ratio. These calculations pre- have diameters in the range 30 to 140A, with a mean size of about 50.4 as observed by electron microscopy. At lower oxidizing temperatures, less than 600°C, no clearly resolved particles are formed, and it is suspected that if A1-0 clusters exist they must be exceedingly small, i.e., 10A or less in diameter. dicto that the particles would vary in size from 15 to 100A. This range of sizes is amenable to detection by both small-angle X-ray scattering and transmission electron microscopy. This paper compares the cluster sizes in such internally oxidized A1-Ag alloys determined by transmission electron microscopy and small-angle X-ray scattering. SPECIMEN PREPARATION Single crystals were prepared from 99.9999 pct Ag, obtained from Cominco Products, and 99.99 pct Al, obtained from Aluminum Co. of America. All melting operations were carried out in graphite molds under flowing purified hydrogen in a horizontal zone refiner. The silver was first degassed,

Jan 1, 1964

By M. R. Geer, H. F. Yancey

John Grifien (Pittsburgh)—I wish to congratulate the authors on this paper, which, I am sure, will promote a clearer conception of the various criteria which have been advanced as measures of coal-cleaning performance. Their clear descriptions of the more important criteria that have been advanced and explanations of their meaning and application have been sorely needed and, if widely promulgated and followed, should remove much of the confusion which, heretofore, has been evident. I suggest that much of this confusion has also arisen from lack of common agreement as to the exact meaning of the words and terms used in our discussions of this subject. I am sure I have been equally guilty in this respect and suggest it is time that we select a committee to study vocabulary as well as criteria, so that common understanding and agreement can be had. Thus, I suggest, that the title of this paper should have used the words "coal-cleaning performance" and not "coal-washery performance." My understanding is that "washery" refers to a complete plant and it has additional functions to that of coal-cleaning, such as control of size, moisture, etc. Also, I do not agree with the authors that the formulas given in their paper, the Fraser and Yancey formulas, are necessarily the only ones that can be called efficiency formulas. When a dictionary is consulted one realizes that the words "efficiency" and "efficient" have not precise meanings but only very general ones and must be further defined for each particular use, if they are to have any precise meaning. To my mind, the first of the Fraser and Yancey formulas given should never be used as expressing "efficiency" alone but only by the fuller phrase which truly expresses the kind of efficiency it states, which is "coal recovery efficiency." For complete clarity we then need only define "coal" for the particular circumstances under which the formula is used. This would recognize the fact, fully explained by the authors, that the limits in coal qualities imposed by the market have imposed a factor—and a variable factor—which has influenced any answer obtained by this formula. Such a procedure makes it entirely practical and logical to use the values of any of the qualities of coal—ash, sulphur, phosphorus, specific gravity—or a combination of them to define what is coal for that particular use of the formula. Further, it is clear to me that the criteria to be used must be dictated by the objective in view and the use for which the data are obtained. The authors clearly point out that the Fraser and Yancey coal-recovery efficiency formula is influenced by three factors, "one is determined by the coal, one is dictated by market or use conditions, and one is an inherent characteristic of the cleaning unit itself." The formula which uses the inverse of misplaced material as a measure of efficiency is also a coal recovery efficiency formula and is influenced in like manner by these three factors. As the authors point out, both are useless in obtaining data which enables a direct and valid comparison of the performance of a given cleaning unit on two coals where the other two factors vary or of the performance of two or more cleaning units of different types unless the values of the other two factors are identical. Much of the confusion in our discussions of and literature on coal cleaning has come from failure to understand clearly this fact. Many such comparisons have been made from which erroneous conclusions have been drawn. I am, therefore, particularly glad to see the authors' emphasis on 4?-1e criteria which indicate the "sharpness of separation. I feel that these are the essential criteria

Jan 1, 1952

By Sherwin F. Kelly, Bela Low, William B. Creagmile

Electrical methods and instruments for geophysical exploration have been almost exclusively applied, during these years of development of the art, by a few companies specializing in this field. The control of patents, the cost of the instruments and the general lack of published information on details of field procedure and office interpretation have given these owners a monopoly in carrying out electrical surveys. The development of the Megger Ground Tester1 seems likely to change this situation, and to enable mining engineers and geologists, without special training in geophysics, to carry out simple reconnaissance electrical surveys. Nevertheless, the need for such special training and experience in planning surveys and interpreting their results remains, and probably i always will remain, indispensable for a successful outcome. The unique thing about, the Megger Ground Tester, which gives rise to this hope for its general use, is its simplicity of operation. The four binding posts of the instrument are connected by insulated wires to four stakes driven into the ground at appropriate points. The crank of the Megger is then turned, and the resistance of the ground between the two inside stakes is read directly, in ohms, by the deflection of a pointer over a scale. The apparatus is shown in Fig. 1. Fundamentally, the principle of operation is that of determining the resistance of a four-terminal conductor, as applied by Frank Wenner to the measurement of earth resistivity. "A four-terminal conductor is a conductor provided with two terminals to which current leads may be connected and two terminals to which potential leads may be connected. The resistance of such a conductor is the difference in potential between the potential terminals divided by the current entering and leaving

Jan 1, 1932

By A. G. McGregor

During the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and equipment developed. Some of these features are described in this paper. Concentrate Hauling, Unloading and Sampling System (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences. A concentrate unloading pocket (Fig. 4), 180 ft.long, is provided at the smelting plant, which has a conveyor belt running throughout its length underneath the track. To unload a car, the vertical plug at the end of the car is lifted by means of a chain hoist which is supported by a trolley overhead. The gate at the end of the car is opened approximately 18 in. The removal of the plug leaves a hole down through the concentrates. The concentrates are poked through the hole from the top of the car until it is convenient for a man to stand on the bottom and draw one of the slats in the bottom toward the gate end of the car. The concentrates are then raked down with hoes on their natural angle of repose,

Jan 1, 1917

By Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mcxico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid curbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1938

By Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mcxico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid curbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1938

By Yang Tsang Woo

I will endeavor to describe the methods of silver-mining and smelting employed by the natives in Mongolia. Modern methods have been applied there, but with little success; and, since they are familiar to most members of the Institute, I will simply mention that the failure was due to the high price of coke used in smelting the ore in modern furnaces, and to the unsuitable mill-machinery employed for concentrating the galena, which is finely distributed in the ore. The Jehol silver-mines are situated about 45 miles NE. of Jehol, the capital of Mongolia. They embrace two mines, 5 miles apart,—the Ku Shan Tze mine and the Yen Tung Shan mine. They were first worked by natives 50 years ago, about the time when mining was so flourishing in other parts of the world,—for instance, in California and Australia. The upper part of the vein is galena mixed with iron-stone, and is 2 to 4 ft. thick. At lower levels the vein is composed of silver-lead ore running between quartz-porphyry walls. Limestone, talc and black shale, colored by graphite, are found in other parts of the mine. Crystalline limestone is found 1 mile NE. of Ku Shan Tze. Granite is encountered in the Yen Tung Shan mine. Mining.—The native method of working the mines is most primitive. The same method may have been employed a thousand years ago. A small inclined shaft, 4 ft. by 4 ft., is sunk in the vein-stuff where the appearances are most favorable. Another shaft is sunk 20 or 30 yds. away, for ventilation. The shaft follows the vein in a zigzag fashion in whatever direction the vein appears to be richest. Timber is used only in soft ground. Where the ground is hard, the roof is cut into an arch-form. In some places, instead of using ladders, steps are cut in the rock, just wide enough to hold one foot. The deepest native workings are 400 ft. below the

Jan 1, 1903

By John J. Collins

[CONTENTS PAGE Purpose and scopeI Core samplingI Sludge sampling.....7 Combining core and sludge assays13 Deviation and surveying of drill holes17 Conclusions24 Acknowledgments25 Bibliography25] PURPOSE AND SCOPE The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described 25,26,31,32.50,65 but more information is needed on the results shown by actual mining operations. CORE SAMPLING The accuracy of diamond-drill-hole sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says, in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change, often indicated by a color change in the sludge water, should be a signal for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By Norman Brown, J. V. Rinnovatore

Substructures in explosively deformed and annealed ß brass have been examined by electron microscopy. In the explosively deformed condition, the structure contains a large density of straight screw type dislocations. Subsequent annealing up to 300oC produces low angle boundaries, which are characterized by superlattice dislocations, and expanded and contracted nodes. Evidence is given where two a(111) superlattice dislocations combine to form two a(001) superlattice dislocations. It is also shown that annealing at 400°C the networks disappear and that quenching from 400" C produces square and circular prismatic dislocation loops that lie on (100) and (111) planes, respectively. THE purpose of this work was to determine the effects of explosive deformation and subsequent annealing in a superlattice using electron microscopy. One of the first observations of explosively deformed structures was made by Hornbogen1 on a iron. Hornbogen found that screw dislocations were most prominent in the explosively deformed structure. He explained this result by suggesting that the edge components of dislocation loops move with the velocity of the shock front leaving a trail of extended screw components. Kressel and Brown2 observed explosively deformed Fe3A1, which is basically a body-centered type of superlattice in terms of dislocation geometry, and found that, as in the case of iron, screw dislocations were most prominent. It was also observed2 that, in cold-rolled and explosively deformed nickel, screw dislocations did not predominate, but rather a uniform network of dislocations was present in which the orientation of the dislocations was random. (Cell structures also have been observed by Nolder and Thomas3 for copper and by Johari and Thomas* for nickel). Kressel and Brown2 discussed the difference between dislocation morphology for bee and fee metals in terms of dislocation mobilities. They suggested that edge dislocations have a greater mobility than screw dislocations in bee metals but not in fee metals. Thus, the idea offered originally by Hornbogen1 is not valid since it should apply equally to fee and bee systems but does not. The results of recent work by Mikkola and cohens on explosively deformed Cu2Au are consistent with other observations for fee metals. They found that dislocations were randomly arranged but there was no significant cell formation. At high shock pressures, deformation twins are produced in fee metals.' High pressures in bee metal should induce the bee — fee transformation while the metal is under pressure. EXPERIMENTAL PROCEDURE The Cu-Zn alloy used in this work contained 51.4 wt pct Cu. Specimens of 0.5 in. diam and 0.012 in.

Jan 1, 1968

By J. M. McDowell, E. C. Doty, F. Morgan

Improvements in the X-ray method of measuring liquid saturation and saturation distribution are presented. Two identical direct current amplifiers have been added to measure continuously the intensities of the X-ray tube output and the beam which has passed through the core under test. The ratio of these intensities is automatically recorded on a modified Brown Electronik Recorder. Arrangements have been made to drive the core automatically and in synchronism with the recorder chart so as to give a continuous curve showing the variation of liquid saturation along the length of the core. By determining the ratio of the two X-ray beam intensities simultaneously the measurements are made essentially independent of small fluctuation in voltage and current supplied to the tube. This improved technique has been used for investigating the fluid distribution along the length of cores and core assemblies when one fluid is displaced by another. Typical results of these studies are shown. INTRODUCTION In a previous publication' a method was described for measuring the oil saturation in cores which was based on the absorption of X-rays by the fluid content of the core. While that technique is capable of yielding accurate results, the original apparatus was not especially convenient for determining the fluid distribution along the length of a core. This was primarily due to the slow response of the amplifier and galvanometer and the necessity of making a point by point survey of the material under investigation. It was, therefore, not only possible for sections of the core having a variable or unusual saturation distribution to escape observation entirely, but changes in output of the X-ray generator between readings on the unknown and the monitor introduced errors in the measurements that could be avoided only by further stabilization of the source or by taking a large number of readings. This paper describes a method and apparatus for recording continuously and automatically the intensity of the X-ray beam that is transmitted by a core. The variation of saturation with time at a given section of the core may thus be found, or by scanning the core by driving it in synchronism with the recorder the saturation distribution may readily be determined. As indicated in the previous paper, the X-ray method possesses an advantage over the weighing technique in relative permeability experimentation in that the core need not be removed from the holder for the purpose of making a saturation measurement. Furthermore, the actual distribution of fluid and the effects upon that distribution of inflow and outflow heads may be investigated. And errors due to gas bubbles or loss of liquid that are frequently sources of error in volumetric methods of saturation determination are avoided. PRINCIPLE OF THE METHOD The energy in an X-ray beam that has passed through an absorbing material is expressed by the well known formula: E = E0, e-cd (1) where E, is the energy in the incident beam, µ the mass absorption coefficient, c the density or concentration of absorbing material, and d is the length of path of the beam in the absorber. The coefficient µ varies with the wavelength of the radiation as well as with the absorbing material. The output of an X-ray tube varies in an approximately linear manner with the tube current, but to the second or higher power of the anode voltage. Moreover, the quality or wavelength distribution of the radiation varies with the voltage.

Jan 1, 1950

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner. Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal. The effect is known as "earing" and the protuberances are called "ears." Other terms frequently heard are "tips," "scallops," and "corners." It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip. 'Numerous papers dealing with various aspects of the earing effect have appeared in the literature, those listed in the references1 being especially interesting and valuable. An investigation of the factors influencing earing of brass cups has been in progress in the laboratories of the American Brass Co. for several years, and it was thought desirable to make some of the results generally available in summarized form. The present paper discusses many factors that do and do not contribute to ear formation. In addition, a section is devoted to methods of minimizing the earing tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced. In the space available, it is impossible to quote detailed experimental procedures and numerical results. However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill. MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions. The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup. A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip. The two-ear form that sometimes appears is also traceable to gauge variations. However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself.

Jan 1, 1942

By T. E. Seidel, A. U. MacRae

The dependence of the electrical and crystalline properties of silicon containing ion implanted boron atoms have been studied as a function of the incident dose, substrate temperature, and annealing tempera-ture. Hall effect studies show that the compensation due to defects is negligible after annealing at and above 500°C for a dose of 1013 ions per sq cm. Steps occur in the isochronal annealing curve for the sheet resistance at 300°C and 800°C and the mechanisms responsible for these steps are discussed. The range of the ions at 150 kev is 3500 * 5001. Electron diffraction studies on samples implanted with 150 ker ions show the existence of damaged (polycrystalline) silicon closer to the surface than the range of the ions. Etching and subsequent annealing of etched and unetched specimens suggest that the poly crystalline silicon is closer to the surface than the bulk of the distribution of ions. THE purpose of this study is to investigate some electrical and crystalline properties of ion implanted boron in silicon. Sheet resistance, Hall measurement, depth distribution by chemical staining, thermal probe and electron diffraction have been used to study the properties of samples implanted in a random direction with ions having energy up to 150 kev. The boron-silicon system has been the subject of considerable study'-7 due to its possible application in the fabrication of electronic devices. The implanted ions produce considerable crystalline damage to the substrate crystal before they lose most of their primary energy and come to rest. Fortunately, most, if not all, of this damage can be removed by subsequent annealing or by holding the substrate at an elevated temperature during the implantation process. Sheet resistivity measurements of the p-type layers produced by boron implantation into room-temperature silicon, reveal that the annealing occurs in a two-step process: the first occurring at -300°C and the second at -800°C.' Electron-microscope and low-angle electron diffraction studies of this damaged material indicate that the bombarding ions produce an amorphous silicon region about the trajectory of each ion.' At high doses, these damaged regions overlap and an amorphous surface layer results. Furthermore, the 800°C annealing step, appears to be associated with the elimination of this gross damage. The depth distribution of the as-implanted and also the annealed samples have been studied by an angle lap and staining technique as well as by Hall measurements.3-7 We find the experimentally determined ranges of the boron are less than those calculated by the Lindhard-Scharff-Schiott theorys (hereafter referred to as the LSS theory). Our results are in essential agreement with pre- vious results. In addition, we have made Hall measurements on samples bombarded with a low dose (2 x 1013 ions per sq cm) to minimize impurity banding effects, and find that deep ionized levels influence the carrier concentration and room-temperature hole mobility until the sample is annealed at temperatures above 500°C. Above this temperature, the data corresponds to that obtained when silicon is doped with boron by conventional techniques. We have also made a depth distribution determination of the crystalline damage due to the implanted boron by using glancing angle electron diffraction techniques. It was found that the gross damage depth distribution of heavily implanted samples is closer to the surface than the depth distribution of the electrically active boron. By removing this gross damage, without affecting the distribution of the implanted boron, we have determined that the 800°C annealing stage is not exclusively due to the improvement in the crystalline perfection of the amorphous material but also appears to be associated with the annealing of some point defects. These results and their relation to previous results are discussed in the following sections. IMPLANTATIONS Boron ions were implanted into silicon samples using an accelerator capable of operating from 10 to 150

Jan 1, 1970

By U. F. Kocks

The flow stress in some latent slip systems of aluminum and silver crystals after various deformations in single slip was investigated by transverse compression and supplemented by experiments on overshoot of the compression axis and the stability of corner orientations. Work hardening was found to be remarkably isotropic, the ratio of the flow stress in the latent system to that in the primary system being between 1.0 and 1.3. The strain-rate dependence was not significantly larger in the latent system. This low anisotropy suggests that specific dislocation interactions are not the direct cause of work hardening. Either the obstacles are essentially impenetrable so that only their distance enters, or a fairly random distribution of dislocations of all systems is. in fact. formed during single slip. The latter seems to he excluded by the observations on the strain-mte dependence and on the amount of secondary strain. The amount of seconzdary strains occurring in single slip was determined by shape-change mensurements and by a new method connected with the latent-hardening experiments. It is definitely less than 1/300 times the strain in the primary svstem. WORK hardening is due to dislocation interactions; this is a hypothesis, and possibly the only one, on which all present work-harden ing theories agree. About a dozen specific interactions have been considered, and it is unlikely that any essential one has been missed. Different work-hardening theories differ to a large extent in the specific interactions which are deemed most important. The presence or absence of any particular interaction, and its degree, depend on the geometrical relationships between the two dislocations interacting. Let us enumerate some examples. Two dislocations may react, with a varying reaction energy, to form a third dislocation, and this reaction product may be sessile or glissile. Two dislocations may intersect and a jog may be formed on both, on one of them, or on neither; this jog may be sessile17Z or glissile and it may, if moved nonconservatively, lead to the production of vacancies or interstitials. Finally, a dislocation may bypass another one and thus interact only with its stress field. All these interactions depend on the specific relation between the Burgers vectors and line directions of the two dislocations. Any dislocation generated during plastic deformation of fcc crystals belongs to one of twelve slip systems. Taking any one dislocation, its relationship to each of the other eleven can fall, by symmetry, into one of only five classes. These relationships are enumerated in Fig. 1 and Table I. Each slip system is represented in the stereo-graphic projection by two triangles, namely those in one of which the specimen axis would have to lie if the specimen were to deform in single slip on this slip system in a given sense, in a tension test. Let us represent the primary slip system by the shaded triangles. The other slip systems are classified only with respect to their relationship to this primary system. The code letters (initials of established names* in German) are explained in Table I. Three specific interactions are also listed in cases where they may be strong: the product of a reaction, the formation of jogs in either system, and the elastic bypass stress. The last column relates to the types of experiments reported in this paper and summarizes their results. To decide experimentally between the relative importance of the various interactions one would like to produce a group of dislocations in one slip system and then measure the stress necessary to force another group of dislocations of a specific second system through them. Hopefully, one can produce the first set of dislocations by plastically deforming the specimen in single slip. Then one can try to achieve single slip in a specific, previously latent system and measure its flow stress. If it is different from the virgin flow stress, there has been "latent hardening". Some types of latent-hardening experiments will be discussed in the next section. The strain-rate and temperature dependence of the flow stress is an indication of the importance of dislocation intersections. By extending an investigation of this dependence to the latent systems, one can determine how much more important forest contributions are here. seeger3 has used the as-

Jan 1, 1964

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal The effect is known as "caring" and the protuberances are called "ears" Other terms frequently heard are "tips," "scallops," and "corners " It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip Numerous papers dealing with various aspects of the caring effect have appeared in the literature, those listed in the references' being especially interesting and valuable An investigation of the factors influencing caring of brass cups has been in progress in the laboratories of the American Brass Co for several years, and it was thought desirable to make some of the results generally available in summarized form The present paper discusses many factors that do and do not contribute to ear formation In addition, a section is devoted to methods of minimizing the caring tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced In the space available, it is impossible to quote detailed experimental procedures and numerical results However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip The two-ear form that sometimes appears is also traceable to gauge variations However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself

Jan 1, 1942

By W. L. Fink, L. A. Willey

This paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium relations have been determined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and aluminum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith † suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extentl,2,3 The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are distinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns. Previous Investigations The solid solubility of magnesium in aluminum has been well established by the work of Dix and Keller4, Schmid and Siebe15, and Saldau and Sergeev6. There is no agreement as to the composition of the magnesium constituents at the aluminum end of the binary aluminum-magnesium system. Hanson and Gayler7 report Mg2Al3; Boyer8 found that the alloy

Jan 1, 1937

By B. L. Sackett

The converting of lead matte is not a general practice at lead smelters, therefore a description of the methods used and developments made during the past 20 years in converting both lead and copper matte at the Tooele plant of the International Smelting Co. in Utah may be of interest. The Tooele converting plant consists of five electrically operated stands in which are used 96 by 150-in. horizontal, barrel-type converters each of about 10 tons capacity. The main converter building is served by a 60-ton electric traveling crane and the casting shed by a 30-ton crane. Copper matte is tapped from near-by reverberatory furnaces into launders that deliver into 8-ton ladles on the converter floor. Lead matte is brought from the blast furnaces, about li mile away, in 5-ton ladles mounted on trucks, hauled by electric locomotives. As the Tooele copper plant has never been a producer of much copper, and has been Irregular in its operation, the original converting plant with its small converters has been adcquate, although decidedly out of step with large, modern plants. Tonnage figures in this paper are for comparison with each other only, as they are not at all in line with prevailing tonnages at larger plants today. The reasons for the changes made in converting practice at Tooele, as well as the improvements in the results obtained as these changes were perfected, are given in the following pages. Lead-matte Converting, 1914 to 1927 In 1914, Oscar M. Kuchs wrote a paper for the Transactions,' describing in detail the lead-matte converting methods at Tooele up to that time. The method perfected only a few months before Mr. Kuchs' paper was written consisted, briefly, of blowing the lead matte alone, without the addition of siliceous fluxing ores, to a point where the lead and zinc were largely eliminated by volatilization. During this period

Jan 1, 1934

By Robin O. Williams

The textures which are produced by simple shear in poly crystalline samples of copper, brass, aluminum, iron, and zirconium have been determined. For the fcc materials, there are two major textures, both of which are oriented for slip on the usual slip systems. It is shown that each grain will, in general, give rise to both orientations through the production of deformation bands. This is considered a clear demonstration that such bands aye produced by the heterogeneous deformation which takes place instead of the five-slip-system model considered by Taylor. The results on iron and zirconium are more limited but would appear to exhibit certain additional complexities. It is suspected, however, that the general consideration of deformation bands may apply here also. One finds some correlation between the textures produced by this single shear and the conventional textures although it would appear- that additional data and analysis are requived to produce a strong correlation. It is somewhat remarkable that of all the texture investigations only a very few have been concerned with the action of simple shear on polycrystalline aggregates. Of these limited investigations, all used torsional strains and only in Backofen's' and Backofen and Hundy's "ork was sampling carried out so as to derive a texture in terms of the shear direction. Some rather remarkable conclusions re- sulted from Backofens'1,2work: 1) the rate of texture formation in copper is high, being almost complete at a shear strain of unity; 2) the texture does not change if the sample is sheared back, although the surface grains return to their original shape; and 3) the texture is complex in that it has four components, three of which have [110] as a shear direction. These conclusions were based on both qualitative and quantitative data. Shear deformation is intermediate in complexity between simple shear of single crystals and the usual deformation of polycrystals; hence, one might expect to learn considerable from the extension of this work. CONVENTION Deformation in simple shear has the lowest possible symmetr3, less than the other simple modes of deformation (rolling, drawing, and compression); hence, one cannot necessarily expect the textures to have the same degree of symmetry. The geometry of the process is represented by Fig. 1 along with its sltereographic projection. One has the shear plane, the shear direction, the mirror plane normal to the shear plane and containing the shear direction, and a neutral plane normal to both the shear plane and mirror plane. These planes divide the projection into four quadrants. These quadrants are not, however, identical, since all directions within the upper left and lower right are being shortened by the shear process, and the other directions are being lengthened. The first kind are called compression quadrants and the direction of greatest contraction rate, at 45 deg, is labeled with a minus sign; the corresponding direction of greatest extension rate

Jan 1, 1962

By M. H. Sommer

MANY attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals com-monly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compression or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and

Jan 1, 1934

By Y. C. Liu

An analysis is presented to show that the formation of rolling textures in fcc metals can be rationalized in terms of flow mechanisms operative during the rolling process. First, a general approach used by Calnan is followed, where the rolling process is approximated on the basis of two axes, p and Q. In this treatement there are two separate sets of slip systems, one for each axis, and it is shown that a homogeneous rotation can he achieved by restricting the slip systems for the two axes to share common slip directions Then, two criteria are used to select the active slip systems for the axis P: they must have relatively high resoloed shear stresses, and dislocations on these slip systems must interact attractively in order to lower total energy content Finally, a method of analysis is introduced to locate the end position of an axis by knowing its acti7.e slip systems. The result of the analysis indi- cates that two main flow mechanisms operate in fcc metals. The ideal orientation derived from one oj-them is (8 13 21) (21 8 13) which is very close to the (358) (523) orientation observed experimentally on the rolling texture of copper. This flow mechanism should only he operative in metals containing dislocations extended into partials separated by less than five times their lattice parameter. The ideal orientations derived from the other flow mechanism are a combination of (1 10} (112) and a spread of orientations with (110) parallel to the rolling plane. This type of ideal orientations corresponds to those observed in the rolling texture of silver 30:70 brass, and binary alloys with high alloying content. This flow mechanism should be operative in any fcc metal regardless of its stacking-fauIt energy. When a polycrystalline metal is subjected to a large amount of plastic deformation, it is generally observed that grain orientations alter and align themselves towards certain positions, eventually reach-

Jan 1, 1964

By J. W. Halley

RIMMING steels derive their name from their action during solidifica-tion in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop ill the molds, are deter-mined by the Composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accu-rately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring condi-tions and furnace practice on the distribution, though there is still much to be done in this direction.

Jan 1, 1938