Search Documents

By Orlando Romig

PART I-PREPARATION OP METALLIC SINGLE CRYSTALS WITH ESPECIAL REFERENCE TO SINGLE CRYSTALS OP ZINC? As metals and alloys are composed, of, an aggregate of allotriomorphic crystals or grains, each possessing an individual orientation, the physical characteristics of a metal or an alloy are closely related to the properties of the individual crystals. The preparation and study of single metallic crystals are, therefore, matters of considerable importance. The advent of the X-ray spectrograph as a valuable metallurgical tool has magnified the importance of this subject, because the interpretation of some X-ray spectrographs is difficult unless single crystals are used in these studies. PREVIOUS WORK The first paper, as far as the writer knows, on the behavior or preparation of single crystals of metals is by Baker.1 He describes the behavior of extruded wires of sodium and potassium. These wires, when pulled in tension, instead of I showing the usual conical fracture common to most metals, had a chisel-shaped fracture when they were broken. I and II, Fig. 1, have a similar fracture. Baker checked his results by preparing single crystal wires from molten sodium and potassium and observing their properties. He prepared the wires by filling glass tubes, under oil, with the molten metal. The surfaces of the strained wires showed slip bands of remarkable clearness of which photographs are shown in his paper. He concluded that these wires were single crystals and "that the portions of the metal brought into play are cubes. Such cubes, when placed so that a plane through 'two opposite edges was parallel to the axis of the wire, would allow of lateral contraction by faces gliding over one another in one direction only and not in the direction at right angles."

Jan 1, 1927

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By Robert A. Campbell, Robert J. Brison

The problem of optimizing from an economic standpoint the capacity of grinding equipment in the design of a new concentrator is discussed. Although directed specifically to copper flotation mills employing conventional wet, grinding, the material presented is considered applicable with modifications to other types of ores and other grinding methods. A general approach to optimizing the grinding capacity is outlined and illustrated by an example. The' interrelation between grinding capacity and other aspects of the project is considered. The problem of regrind capacity and its relation to preceeding and subsequent processing steps is also discussed. Finally, factors are considered that may, in certain cases, dictate modifications of the suggested approach.

Jan 1, 1974

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By C. O. Bundranl, Peter Dehlinger, W. H. Browne

Brief laboratory investigations are described which attempt to determine optimum .sand concentrations in gel-sand and oil-sand1 well-treatments. The investigations apply to the case where sand acts as a propping agent in formation fractures. Both analytically and experimentally it is demonstrated that optimum sand concentrations can be defined. It is difficult to translate laboratory results to field treatments, however, since the relative distribution of sand and fluid in fractures may not be the same as injected. This is because fluid may penetrate the furtherest narrow portions of fractures, which would not pass sand. Optimum concentration of a monolayer of Ottawa sand in fractures of 0.025-in. width at the usual range of pressures encountered in treatments appears to be about 95 to 2 lb/gal. of gel. An investigation of abrasion of rock-walls by sand in treatments, described in the Appendix, shows that such abrasion is not probable in significant amounts. INTRODUCTION Experience in the Spraberry formation of West Texas, as well as in other formations, has shown that. sand is a necessary and vital part of gel-sand and oil-sand treatments. Many observers of treatments have also concluded that there seems to be an optimum range of sand concentration for these injections. Brief laboratory investigations were made at Battelle Memorial Institute to study flow in fractures with different sand concen- trations. To investigate the existence and range of optimum concentrations in the laboratory, however, necessitates knowledge of the mechanism by which the sand aids in increasing subsequent production. The action of sand in fractures is usually thought to be either that of a propping agent, thus providing a greater effective formation permeability; that of an abrasive in eroding fill material in fractures; or that of an abrasive eroding rock-wall irregularities along fracture surfaces. Investigations described in the Appendix show that sand does not appear to erode rock-wall materials appreciably. In a subsequent paper it is reasoned, at least for the Spraberry formation of West Texas, that the primary action of sand is not in removing fill materials in fractures. In this formation, and probably others, too, the main effect of sand appears to be that of a propping agent. Both analytical and experimental investigations were made for the case of a monolayer of sand acting as a propper, in which sand concentrations were determined that would, after treatment, permit flow of the maximum quantities of oil from the formation into a well. If too few sand grains are injected into fractures in which the bottom hole pressure has decreased appreciably below the original formation pressure, the confining pressure in the formation may become relatively large, thus compress the rock-walls around the sand grains, essentially close fractures, and so decrease the subsequent flow of oil. Similarly, if too much sand is used, the flow of oil will he impeded by the volume of sand present. THEORY Although an analytical approach to determining optimum sand concentrations involves gross assumptions.

Jan 1, 1955

By L. S. Panyity

The Cleveland (0.) gas pool described by Frank R. Van Horn,' is the northern extremity of the great "Clinton" sand gas development in Ohio. Numerous gas pools have been developed in this formation, which are now more or less connected, link by link, forming an almost continuous gas pool, starting at Cleveland, and running thence southward through Cuyahoga, Medina, Wayne, Ashland, Richland, Knox, Licking,

Jan 1, 1918

By W. T. Olsen, R. Ulcer

WHEN a liquid alloy freezes, the solid first formed usually differs widely in chemical composition from that last formed, so that there is segregation in the alloy as cast. For example in the copper-nickel system (fig. 1) the first solid formed from a liquid containing 55 atomic pct Cu may contain as little as 38 pct Cu, while the last must contain well over 55 pct. Three factors may act to decrease segregation from the maximum possible. 1. Diffusion in the cooling solid tends to make the phase homogeneous, decreasing segregation. This may be important at slow rates of cooling. 2. Segregation is impossible without diffusion in the liquid. At extremely rapid rates of cooling there may not be enough time to allow maximum segregation. 3. Supercooling delays nucleation to temperatures well below the liquidus thereby decreasing segregation. Hence the first nucleus in the copper-nickel system may contain well over 38 pct Cu. At sufficient supercooling the first nucleus may form below the solidus, in which case there is no reason to expect any segregation whatever. From these considerations, we could predict that at sufficiently low rates of cooling the alloy would be unsegregated because of factor 1 and at sufficiently high rates of cooling there should also be no segregation because of factors 2 and 3. Considerable segregation should occur only at intermediate rates of cooling. We have demonstrated experimentally that segregation can be completely suppressed by rapid rates of cooling. For the alloys studied, however, these rates are too great to be attained in any commercial practice. An alloy of 55 atomic pct Cu, 45 atomic pct Ni was frozen by cooling at varying rates. The degree of segregation in the solid was determined by X-ray diffraction photographs. Slow rates were obtained by slowly cooling the furnace containing the liquid alloy; fast rates by pouring or ejecting droplets of the alloy into water or iced sodium hydroxide solutions. The cooling rate of the droplets can be cal-culated from their dimensions by assuming reason- able values of thermal conductivity.' The experi-ments were repeated with an alloy of 16.5 pct Cu and 83.5 pct Au. A single experiment also showed a 50 atomic pct Bi-Sb alloy had no segregation at the most rapid quench. The position of back-reflection X-ray diffraction lines is a highly sensitive function of the lattice constant, which in turn depends on the chemical composition of the phase. A phase of varying composition will give broad diffraction lines. By measuring the edges of these lines and making suitable corrections for intrinsic line width, it is possible to determine the range of lattice constants represented. These can be converted to chemical compositions from a lattice constant vs. composition curve. Results are shown in table I. In the copper-nickel system the greatest segregation is found at the slowest cooling rates, where the lowest percentage of copper theoretically possible is found. In the copper-gold system, on the other hand, the degree of segregation is decidedly less at the slowest rates of cooling, being greatest at 11,100°C per sec. At no rate is the theoretically lowest percentage of copper (12 pct) found. At the rates of cooling found in sand and die castings the degree of segregation is large and depends little on the rate of cooling. Acknowledgment Most of the material in this paper is abstracted from a thesis presented by William T. Olsen, Jr. in 1948 in partial fulfillment of the requirements for the degree of Master of Science at the University of California.

Jan 1, 1951

By Rodney P. Smith

The rate of motion of the boundary between a single-phase a-iron region and a two phase a-iron plus ?-iron, or a-iron plus cementite region has been measured on decarburization at several temperatures between 500" and 865°C. These data, together with data for the carbon content of a-iron at the boundary, yield the diffusivity of carbon in a-iron. The activation energy for carbon diffusion is 19.8 kcal per mole for the temperature range —50° to 150°C and increases to an average value of 23.0 kcaL per mole for the temperature range 727" to 865°C. AS part of an investigation of the diffusivity of carbon in iron using a steady-state method,' the diffusivity of carbon in a-iron was determined at the temperatures 802" and 851°C. The diffusion constant thus obtained was larger, by nearly a factor of two, than that predicted from the combined results of stanley2 and of Wert.3 It seemed desirable, therefore, to continue the investigation. Since the temperature range in which the steady-state method can be conveniently used is limited, we have chosen a decarburization method, based on the laws of diffusion in metal accompanied by a phase change.4,5 If the initial carbon content of the Fe-C alloy is such that two phases coexist at the decar-burizing temperature* and decarburization is car- ried out such that the surface is maintained at substantially zero wt pct. C, the carbon distribution after a time, t, will be as shown in Fig. 1. The boundary between the single-phase and two-phase regions moves from y = 0 to y = x in the time, t, where x is proportional4 to tl". If the initial carbon (content of the sample is Ci, and CB is

Jan 1, 1962

By S. D. Dahlgren

ORDERED G.P. zones having the cesium chloride structure were found to exist in the bcc iron-rich grains of an Fe-Au-Cu alloy that had been supersaturated with approximately equal atomic percentages of gold and copper, and aged at 400° and 350°C. Streaks and superlattice spots in electron diffraction patterns revealed the presence of the ordered zones in the aged material. The ordered Ll2 structure is commonly found for precipitates in fcc metals (e.g., Ni3A1 in nickelL7') but it is uncommon to find precipitates in bcc metals having the cesium chloride structure. The formation of the G.P. zones caused age hardening of the grains. Samples containing 3.8 at. pct each of gold and copper (with the remainder being iron) were annealed at 95@ or 1125°C in quartz capsules and were quenched by breaking the capsules under water. X-ray diffraction patterns revealed two solid solutions in the quenched samples. One solid solution was bcc and the other was fcc. The microstructure consisted of iron-rich grains of 0.3 mm diam surrounded by a yellow gold-copper-rich grain boundary network. The Au-Cu phase diagram %hows continuous solid solubility of gold and copper with ordered phases forming below 410°C. None of the ordered Au-Cu phases have the cesium chloride structure. Both Fe-Au and Fe-Cu phase diagrams3 show extended miscibility gaps and only terminal solid-solution phases. Consequently, it is reasonably certain the iron-rich grains consisted of an a-phase terminal solid solution, and the grain boundary network consisted of a gold-copper-rich terminal solid solution. Lattice parameters of the quenched solid solutions were consistent with the suggestion that the quenched phases were terminal solutions. The lattice parameter of the bcc phase (2.879A) obtained upon quenching from 950°C was higher than that (2.866A) for pure iron. The fcc phase in this sample had a lower lattice parameter than that for a 50 at. pct Au and 50 at. pci Cu solid solution, i.e., 3.866 compared to 3.877A. The lattice parameter for the 50 pct Au and 50 pct Cu solid solution was interpolated from data for Cu-Au solid solutions.4 More gold and copper were soluble in iron at 1125°C than at 950°C as indicated by a 0.012A increase in the bcc lattice parameter for a sample quenched from 1125°C. After the alloy had been quenched from 950° and 1125°C, the bcc lattice parameters were 2.879 and 2.891A1 respectively G.P. zones having the cesium chloride structure-which formed during low-temperature aging—were detected by electron diffraction and observed with electron transmission microscopy. In Fig. 1, the asymmetrical streaks parallel to ( 100) directions indicate that platelike G.P. zones had formed parallel to (100) planes of the matrix. The direction of streak asymmetry shows that the bcc unit cell of the G.P. zones was larger than the bcc cell of the matrix. The ordered cesium chloride structure is indicated by low-intensity superlattice spots at 010 positions which are nonallowed for bcc structures. The superlattice spots are streaked; therefore they are from the G.P. zones and are not caused by rel-rod effects of a thin matrix phase. The appearance and size of the zones observed in electron transmission microscopy and the appearance of the asymmetrical streaks in the electron diffraction patterns for the Fe-Au-Cu alloy were the same as those observed for a similarly treated Fe-Au alloy.' Ordered G.P. zones were detected also for an Fe-Au-Cu sample aged only at 400°C. The production of the ordered cesium chloride structure zones by low-temperature aging of super-

Jan 1, 1968

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-'; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-'. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1'2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By Dorsey A. Lyon, Robert M. Keeney

The electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in thc production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly by the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name "refining" is applied to the present finishing process, because in the operation oxygen and other impurities arc removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral, the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities. The reverberatory melting of cathode copper is one of the weak parts

Jan 1, 1915

By S. R. Goodman, Hsun Hu

A detailed study of texture developmenf in poly crystalline copper atzd 70-30 brass has been completed. Textural changes as a function of deformation are shoum by pole jigmres and by intensity measurements oF- various rejlectiotzs from the rolling plane and the rolling direction. These examinations were accompanied by measurements of stacking fault frequency, hardness changes, and microstructure. Some of the results were briefly presented earlier. Additional results reported here are consistent with the idea that deformation faulting or slip by partial dislocations is of primary importance in the formation of deformation textures in fcc metals. lo examine the idea that deformation faulting is of primary importance in determining whether the texture is the copper type or the brass type an extensive study of the development of polycrystalline textures in copper and 70-30 brass was initiated. Besides the determination of complete pole figures, the intensities of the various reflections from both the rolling plane and the plane perpendicular to the rolling direction, the peak shifts due to deformation stacking faults, and the hardness of the rolled specimens were examined at various reductions from 10 to 99 or 99.5 pct. Mi-crostructures were examined by transmission electron microscopy. Some of the results were briefly presented in an earlier publication.' Since then, additional information has been obtained. This is given in the present paper. EXPERIMENTAL PROCEDURE Material and Specimen Preparation. The material used was a commercial electrolytic copper bar 1i in. wide and 2 in. thick and a 70-30 brass bar la in. wide and 1i in. thick. Chemical analysis indicated a purity of 99.97 pct for the copper, with 0.025 pct 0 as the major impurity. The 70-30 brass was of higher purity with 0.0016 pct 0 as the major impurity. Extreme care was taken in the preparation of the starting material to insure uniformly fine grains with a nearly random initial texture. The two bars were first cold-forged and then annealed to eliminate any original texture. The grains were then refined by several cold rolling (approx 30 pct reduction) and annealing treatments. The + -hr anneals were carried out in a salt bath at 390" to 440°C for copper and at 490°C for brass. The resulting penultimate grain size was 0.06 mm for copper and 0.03 mm for brass, and both showed very little preferred orientation. The number of prior cold rolling and annealing cycles was such that the final thickness after various final reductions of 10 to 95 (for brass) or 99 (for copper) pct was the same (0.020 in.). These annealed strips were rolled in two directions by reversing end for end between passes according to the following schedule: 0.006 in. per pass to 0.100 in., 0.003 in. per pass to 0.050 in., 0.002 in. per pass to 0.025 in., 0.001 in. per pass to 0.020 in. Texture Determination. The development of rolling textures was studied by examining complete pole figures determined from the (111) reflection. Specimens thinned from one face of the strip to half thickness (0.010 in.) were used to obtain the central portion of the pole figures, while specimens thinned from both faces to 0.003 in. were used to obtain the peripheral portion. The reflection and transmission techniques have been described previously. In addition to X-rav pole figures, texture development was also studied b; examining the intensity variation of the (Ill), (200), (2201, (311), (331), (420), and (442) reflections from the rolling plane and from the plane normal to the rolling direction, as a function of deformation. The same specimens used for the central portion of the pole figures were used for the intensity measurements of the various reflections from the rolling plane. For intensity measurements from the plane normal to the rolling direction, composite specimens were prepared by mounting sections cut parallel to the transverse direction of the strip. An epoxy resin was used to bond these sections together, and the entire composite was then mounted in a cold-setting resin to facilitate subsequent polishing and etching to remove distorted metal at the cut. The intensities were expressed in units of the integrated intensities measured from an annealed copper specimen having almost no preferred orientation. Stacking Fault Frequency Determination. Following the analysis of Warren: the stacking fault frequency, a, was determined from the change in the peak separation (A%) of two neighboring reflections of a deformed specimen, as compared with the normal peak separations of a fully annealed specimen. To obtain sufficient intensities for the second-order reflections, (222) and (400), composite specimens were prepared from parallel sections cut from the strip at 30 deg to the rolling direction for copper and 25 deg for the brass.* From texture data, these sections are known to contain a large population of both (111) and (200) planes. Since residual stresses can also cause X-ray line shifts (the direction of line shifts depends upon the sign of the stress), the use of composite specimens consisting of sectioned planes should help compensate for these effects as the residual stresses change sign from the surface to the central section of a rolled strip. Since the amount of peak shift is almost un-measurable in brass rolled 15 pct and in copper rolled

Jan 1, 1969

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By T. V. Philip, R. E. Lenhart

C. G. Dunn(General Electric Research Laboratory)— It is well recognized that understanding of the formation of the cube-on-edge texture in annealed commercial cold-rolled Si-Fe strip is important industrially as well as scientifically. I would like to make a few remarks on this subject, discuss some points in the present paper, and list two remaining problems that appear to be particularly outstanding. Attention should be drawn to the paper by P. K. Koh,23 which also considers the kinetics of secondary recrystallization in 3 pet Si-Fe, produced commercially by the Allegheny Ludlum Steel Corp. Koh covered a much larger temperature range than do either the present authors or P. N. Richards, whose work is mentioned in a footnote. Koh found an induction period (of short duration) even for isothermal anneals at 1260oC (2300°F). Koh and Dunn24 also found a change in texture during the 1260oC anneal for the same material. On the other hand, the material in coil D, according to Philip and Lenhart, underwent no sec-condary recrystallization, only continuous grain growth. The grade classifications of the four coils studied would suggest, however, that all four materials had developed the cube-on-edge or (110) [001] texture, but to varying degrees. Since no data on this are given and since watt loss depends

Jan 1, 1962

By Alfred Weiss

When I first received the announcement of this meeting I was pleased to see that this 14th APCOM Symposium had expanded its range of interest. One new topic to be considered this year is long range or strategic planning--the continuous process by which current risk taking decisions are made systematically, and with the greatest knowledge of future impact. Long range planning should receive our attention. It is the first step in the management process and the foundation of many--if not all --key managerial decisions. Improvements made at this stage of managing are almost certain to be of benefit in later stages of decision making. It is obvious to many of us that in a physical process such as mineral beneficiation, one does not concentrate all of one's attention on the flotation design without also considering the grinding, cycloning, and desliming stages of the process. Taking this a step further it would be equally erroneous to find a mineral engineer designing a mill without due consideration for mine, smelter and refinery and beyond that the sales goals, growth and profit objectives of the firm itself. And yet, how many times have we seen organizations staff and reorganize without consideration of an overall plan; without adherence to the management process which by its definition, calls for a plan first, followed by the appropriate organization and staff. The computer applications traditionally discussed at APCOM meetings have concentrated on areas dealing with things and people-- the implementation of the plan, rather than with concepts and ideas, the formulation of the plan.

Jan 1, 1977

By L. G. Truby

This paper presents the results obtained after calculating matches of the observed pressure performance of five fields completed in a common aquifer. A general dejcription of the Central Basin Platform area in West Texas in which the five fields, Andector, Embear, Martin, TXL, and wheeler, are lo. cated is contained in the paper. The method of utilizing the electric analyzer to calculate simultaneously matches of the observed pressure performance of the five fields is outlined. The determination of boundaries of pressure communication is discussed and the extent of pressure interference between fields consistent with the configuration of the area aquifer is shown graphically. INTRODUCTION Anomalies in the pressure performance of the Andeector Ellenhurger Field resulted in an investigation of pressure interference between several Ellenburger fields located on the Central Basin Platform in West Texas. Four fields, Embar, Martin, TXL, and Wheeler, were found to contribute significantly to the pressure drawdown at Andector. An initial investigation of the pressure performance of the Andector Ellenburger Field revealed that the reservoir pressure could not be matched by the calculation technique usually applied to water drive reservoirs. In the past, many have advanced the opinion that fracturing in the Ellenburger was a local condition restricted to the immediate uplifted area around the field, in which case each field would in all probability be surrounded by its own relatively small aquifer. Following several unsuccessful attempts to account for the pressure performance at Andector, a system assuming a common aquifer involving several fields in the immediate vicinity of Andector was placed on the electric analyzer and the effect of lo. interference was noted. A refinement of the initial analyzer calculations involved the determination of the approximate boundaries of the aquifer, the calculation of detailed matches of the pressure performance of the interfering fields, and an evaluation of the degree of communication between fields. DISCUSSION Geology and Development The fields considered in this work are located in the Central Basin Platform, a north-south trending structural feature in West Texas lying between the Delaware Basin to the west and the Midland Basin to the east. The locations of various individual Ellenburger fields in this general are shown in Fig. 1 with the five major fields which appear to be definitely intercommunicating colored in black and located in the circled portion of the figure. Production from the five fields was first obtained from the Embar Field discovered in July 1942, followed by the Wheeler Field in 1943, the TXL Field in 1945, and the Martin and Andector Fields in 1946. The total reservoir fluid production from these fields is indicated in Fig. 2. As illllstrated in this figure, very little production was taken from these fields prior

Jan 1, 1952