Search Documents

By J. L. Christie

A recent case of failure of a-low karat gold alloy by stress-corrosion cracking is of interest because it illustrates a principle frequently overlooked: the relation between high residual stress and high yield point. The alloy contained Gold, per cent 39.6 Copper, per cent 51.1 Silver, per cent 5.2 Nickel. per cent 3. 1 Zinc, per cent 1.0 Tension tests on the alloy showed the following:

Jan 1, 1945

By M. J. Salkind

In discussing the possible contribution of plastic deformation to neck growth during sintering, Wilson and Shewmon State that Lenel, Ansell, Salkind, and Early34, 35 concluded that dislocation flow is the rate-controlling process in sintering under zero external load. The experiments cited34, 35 were done with applied external loads, and the conclusions were that the same kinetics could be controlling sintering due to the force of gravity with no additional applied load. The effect of gravity on sintering behavior was previously cited.34, 31 In addition, Wilson and Shewmon argue that the conclusions of Refs. 34 and 35 are doubtful because the strain rate is proportional to stress for plastic flow. This assumption is true only for certain kinds of plastic flow such as Nabarro-Herring Microcree38 As Early, Lenel, and Ansell point out3' plastic flow, based upon dislocation movement, can exhibit strain rates which exhibit a power law relationship to the applied stress.39, 40 Wilson and Shewmon also doubt the results of Refs. 34 and 35 because the stresses in the necks are too small for x/a > 0.1. This is true, and the experiments described in Refs. 34 and 35 were done for small values of %/a. The conclusion was that plastic flow by dislocation movement was important during the early stages of sintering when x/a is small.

Jan 1, 1968

By Charles B. Dudley

THEO. N. ELY, Esq., Superintendent of Motive Power. DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails and their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? You will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light * At the Lake George meeting of the Institute in October, 1878, I had the honor of presenting to the Institute, through the kind permission of the officers of. the Pennsylvania Railroad Company, the results of a study of twenty-five samples of steel rails, which had all been in actual service. Considerable discussion followed the publication of that paper, and there seemed to be a strong disinclination, especially on the part of the steel-rail manufacturers, to accept the conclusions presented. One of the principal objections urged against the conclusions drawn was, that they were based on too few samples; in other words, that no conclusions safe to act upon could be drawn from the examination of twenty-five rails. In view of this criticism it was decided to repeat the investigation with a larger number of samples, and with the aid of the experience gained in the first investigation. The results of this second study of steel rails are, by the permission of the officers of 'the Pennsylvania. Railroad Company, herewith presented to the Institute, with the sincere desire that they may aid in adding to our knowledge of this most important product. Like the previous paper, this is in the form of a report to one of the officers of the company, which will account for the style, and the manner of presenting the data

Jan 1, 1881

By C. A. Eligwe, F. W. DeVries, A. E. Torma

This study is an investigation on using hydrogen peroxide for tank-leaching of uranium with sulfuric acid. The optimum sulfuric acid concentration was found to be 0.03 mole 11 -'for a 25% pulp density suspension. The order of reaction with respect to sulfuric acid concentration was found to be ns0.75. The best results vith hydrogen peroxide were obtained at a 4.64 molar ratio of 6202 to U in the ore. The order of reaction was found to be zero with respect to hydrogen peroxide concentration. The theoretical maximum rate effect of Hz02 on uranium extraction was derived as Vm = 8.15 x mole &-'min-'. The highest rate experimentally attained was 8.09 x mole kL'min-'. It was found that the uranium extrac- tion was not affected by the pulp density up to the 50% used in this study. However, the final yieldswere significantly higher (over 90%) for leaches carried out in the presence of Hz02 than (less than 90%) for leaches carried out in the absence of H202. The reaction was found to follow a first order course with respect to substrate concentration (pulp density) regardless of the presence of H202. The effect of temperature was more explicit at moderate tempetatures (30 to 55 C) than at lower (10 C) or at higher (70 C) temperatures. At this latter temperature an almost complete extraction was realized even without H202. The apparent activation energies were found to be AEa = 2.68 kJ mole-' in the absence of H202, 0.5 kJ mole-'with Hz02 at 40 C to 70 C. and 4.72 kJ mole-' with Hz02 at 10 C to 40 C. All these activation energy values suggested that the uranium extraction process is diffusion controlled regardless of the presence of H202. Further, the change in activation energy in the presence of Hz02 indicates the possibility of change in the reaction mechanisms at lower and higher temperatures.

Jan 1, 1980

By H. H. Rachford, and J. D. Rice

The effectiveness of digital computing machines in making technical calculations depends on how well the work is arranged to utilize the capability of the machines. This note presents a particularly useful way of calculating hydrocarbon vapor-li.quid equilibrium in the flash vaporization (or condensation) system. The method is well suited to sequence-controlled computing equipment. It is not limited to equilibrium calculations and may be used for solution of most implicit equations in one variable. INTRODUCTION There is increasing interest in the use of electronic digital computers in research and engineering calculations. This is a fortunate and inevitable trend in view of both the increasingly extensive numerical work which is becoming a routine part of many daily production operations and growing demand for the overwhelming amounts of calculations required by newly developed numerical methods for solving heretofore unsolved problems. Machines are in many ways ideally suited to the task but of necessity present certain difficulties. for a particular poblem to be solved must often be formulated quite differently from the way it would be arranged for manual solution. This is done in order to take advantage of the inherent speed and precision of electronic computers and at the same time to limit the need for number storage to the capacity of the machine. Therefore, this note is submitted to present a general and quite powerful method of finding solutions of the frequently encountered implicit equation: F(x,y1,y2,...ya)=0.......(1) where the root, x, is to be found for a given set of y1, ... yn.. The procedure is well suited for use with computing machines, for it usually requires but little storage or programming beyond that necessary to evaluate F. HYDROCARBON EQUILIBRIUM The method is described in terms of the problem it was designed to solve, i.e., the calculation of hydrocarbon vapor-liquid equilibrium in flash vaporization. Given the composition of a hydrocarbon mixture and appropriate values of the equilibrium ratios K, to find the phase ratio and compositions in a closed system: let z, be the mol fraction of the i-th component in the mixture. If K, is the ratio yl/xl, where y, and x,

Jan 1, 1952

By E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredg-ing operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. DREDGING AREAS The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California.. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were deposited relatively near the source; consequently, in' the higher moun-tain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows.

Jan 1, 1937

By Neil Johnson

IN the cyanidation of gold, silver and mixed ores, the solids suspended in the pulp after fine grinding, primary settling and series agitation are subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D. The conventional C.C.D. plant consists of a series of separate thickeners-three to five in number-arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they are diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D. plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in series instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and seal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-ance with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a dia-phragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By J. B. Agan, R. J. Fernandes

This paper utilizes the layered-system approach, modified to include areal sweep efficiency, to determine the miscible-slug size required and to predict the perfort7zance of a miscible-slug process in a highly stratified reservoir having a permeability variation of 0.76. The slug size in each layer was determined from theoretical calculations and laboratory data which showed that, to maintain miscibility in the reservoir, the slug size had to be 8.2 per cent of the floodable hydrocarbon pore volume. Economic considerations, however, such as the value of the miscible product injected, the cost of injection and the cost of reprocessing the miscible product, limited the amount of miscible product which could be injected into the lower-permeability layers. This resulted in subjecting only 60 per cent of the reservoir to a slug size sufficient to maintain miscibility. Utilizing the relationship of producing gas-oil ratio and areal sweep efficiency as a function of pore volume injected (as obtained from data published by Dyes, Caudle and Erickson2), the theoretical performance was determined. This prediction is compared with actual performance to date. Actual performance reflects an increasing percentage of tniscible product in the produced fluid to a particular level, which remains static for a short period and then increases again to a higher level. This performance suggests that the reservoir has performed as a layered system. It is concluded that the layered-system approach can be used to predict performance in a highly stratified reservoir and that economic consideration is a limiting factor in determining the amount of the reservoir which can be miscibly swept. INTRODUCTION The Paloma zone in the Paloma oil field, Kern County, Calif., is comprised of several sand members separated by siltstone, shale and/or cherty sections. Rapid facies changes within the zone indicate that the sediments were deposited in a "near shore" environment. As a result, the Paloma sands have a high permeability variation, and the Paloma zone is comprised of several sand reservoirs. Since one of the sand reservoirs containing crude oil was not receiving the benefits of gas injection, consideration was given to recompleting certain wells to isolate the sand in order to perform a miscible-phase injection project and, thereby, to increase its ultimate oil recovery. Before proceeding with the project, a review of the literature was made to determine the miscible-slug size that would be required to maintain miscibility throughout the displacement process. Although the review showed that considerable information was available for homogeneous systems, insufficient information was available to determine slug-size requirements and to predict performances for a highly stratified reservoir. This paper has been prepared to describe the method used to determine the miscible-slug-size requirement and to predict the performance of the miscible-phase injection project initiated in the Paloma oil field. Although the Paloma project has only been in operation since Aug., 1958, sufficient production history has been obtained so that a comparison can be made with the predicted performance. DESCRIPTION OF RESERVOIR The reservoir in which the miscible-phase project was initiated in the Paloma field is shown on Figs. 1 and 2. Reservoir properties are as follows: average sand thickness, 43 ft; porosity, 19.1 per cent; water saturation, 47.2 per cent: oil viscosity, 0.328 cp; reservoir temperature, 250°F; reservoir pressure, 3,500 psi: gas saturation, 21.2 per cent at time of miscible product injection; and total net hydrocarbon pore volume, 19,993,000 reservoir bbl. LIMITATIONS The method described herein utilizes a layer-system approach, where injection into and production from each layer is assumed to be proportional to the layer's fractional capacity. The effects of increased fluid mobility on injection and production rates, in layers which have had breakthrough, are not reflected in this method. There has been considerable controversy over the slug size necessary to maintain miscibility throughout the displacement process. In this method, the slug-size

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

Alfred E. Hunt, Pittsburgh, Pa. (communication to the Secretary): Mr. Blue's statement (page 576) that, " owing to the presence of iron and other impurities, makers of aluminum. assert that native corundum is unsuited for the production of that metal," is somewhat incorrect, at least so far as it may refer to any objection made by the officials of the Pittsburgh Reduction Co. to the Canadian corundums. We recognize corundum as among the richest and purest of the ores of aluminum, and the material furnished from Canada would offer for us the advantage of a supply near to our works for the manufacture of aluminum at Niagara Falls. The real difficulty which we find in the use of corundum for this manufacture is the cost of the raw material as compared with that of native bauxites. In this item we include not only, the price of the corundum as it has been offered to us, but also the expense of grinding it to an impalpable powder, which must be done before it can be used directly in the manufacture of aluminum, and the cost of preliminary chemical treatment for purification—which latter operation, however, is also required for bauxite. I agree with Mr. Blue that the introduction of new and irnproved processes has greatly reduced, during the past ten years, the cost of manufacturing aluminum; but I am inclined to believe that any further improvements, facilitating the use of corundum for this purpose, would apply, in equal or greater degree, to the common clays (silicates of aluminum) which exist in all parts of the world, are more easily mined and handled, and are likely to be always cheaper per unit of aluminum than any corundum.

Jan 1, 1899

By William Kent

ABOUT a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh. Car-wheel Works, in making a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and pro¬vided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to , 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0088 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam was told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hand-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 44,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

By H. Biloni, H. R. Bertorello

GruZLESKI and winegard1 have recently reported on the origin and development of the cellular substructure in Sn-Cd eutectic unidirectionally grown with different amounts of constitutional supercooling (CS). This communication deals with the results obtained in a parallel study on the instability of a plane interface in Al-Cu eutectic unidirectionally grown. Similarities as well as differences with the results of these authors1 will be presented. A1-Cu eutectic alloy ingots of 99.999 pct purity were grown unidirectionally under different G/R ratios where G = thermal gradient in the liquid, R = solidification rate. The ingots were cut in slices perpendicular to the solidification axes and the substructure studied on parallel sections following the sense of growth. It was generally found that the last part of the ingot to solidify presented a well developed colony substructure as a result of impurity build up and constitutional supercooling. The results obtained were: 1) When the structure was observed with low niagnification (of the order of 150 to 300 times) the first instabilities were observed at the grain boundaries and node-like structures formed at the junctions of the growth-induced boundaries, as reported by Gruz-leski and Winegard.1 Inside the grains the first signs of instability appear later and correspond to the type shown in Fig. 1; this is a two dimensional cell substructure. ' 2) Figs. 2 and 3 correspond to the evolution from a two dimensional substructure to a cellular type. In the A1-Cu eutectic the boundaries of the two dimensional cell are always perpendicular to the laniellaes instead of parallel as in the Sn-Cd eutectic. 1

Jan 1, 1970

ANYONE who wishes to make the patterns for statues in order to cast them later in bronze, even though he himself is the artificer who made them, must take many things into consideration: first, whether they are large or small, and whether they are wholly round or only in part; then of what material they are made, for the way that can be followed if they are of wax cannot be used if they are of clay, wood, marble, or even of plaster; likewise he must consider whether or not it has irons inside to support it. There is also a great difference in facility if the support is placed more in. one way than in another. Great consideration should be given to whether it is to be made hollow or solid. If you have not been the workman yourself, you must at least have been an active helper in this and in every other part in order to be able to observe everything without a fault. For if they are large it is necessary to make their moulds in pieces, with marks and measurements so that you can replace them-at will exactly in the same order and in the same places after they have been taken out. But if you are the artificer [as well as sculptor] the process is made easier. Taking the ordinary way and, over an iron, make out of well beaten moulding clay, compounded with cloth clippings a core exactly as the statue is to be or however large you wish the hollow to be. Dry and bake it. On top of this work the wax, thickening it all over as much as you wish the bronze to be and finish it completely, remembering to arrange that the base may come out solid with bronze so as to support the whole work. Then take some rods of hammered bronze one dito thick and one palmo long. Pass these throughs the thickness of the wax and fasten them in several places in the core of clay that you made. [81] Do it so that they, project out of the wax a good three or four dita. These are, put in so that when the wax is removed the core is held in the middle of the mould that forms the outer part, and this outer part is held by the inner part, namely the core, so that the mould may not move in any part from its place even when it is handled. This done, take some of that clay made with well-prepared cloth clippings as I taught you, and mix with it if you wish some wash ashes or

Jan 1, 1942

By T. C. Craig

During the year, there were 570 oil wells completed for a total daily initial production of 365,352 bbl. The daily oil potential of the field, effective Jan. 1, 1935, as established by the Texas Railroad Commission, was 306,102 bbl. with a daily allowable of 58,800 bbl., whereas, on Dec. 31, 1935, the potential was 587,376 bbl. with a daily allowable of 57,800 bbl. Because of the limited market demand, the allowable decreased although the potential increased. In August, the five-day test for determining the potential production of a well was replaced by a 24-hr. test. The reason for this change was that some of the oil-pur-chasing companies contended that too much oil in excess of the limited market demand was produced during the five-day tests. Dry Gas.—During July, the Texas Railroad Commission supervised the first complete and accurate field-wide test of open flows that has been made in this area. The total open flow as determined at that time was 16,426,085,000 cu. ft, There were 79 gas wells drilled in '935, with a combined open flow of 2,408,000,000 cu. ft. and 50 depleted oil wells were plugged back for gas with a total open flow of 529,800,000 cu. ft. The total new gas production for the year was, therefore, 2,937,800,000 cu. ft. The 17 natural-gas pipe lines drawing on the Panhandle supply of fuel gas withdrew a daily average of 420,497,507 cu. ft., or a total of 153,481,-590,000 cu. ft. for the year. The 44th Texas Legislature passed a statute known as House Bill No. 266, which was designed to prohibit waste and protect correlative rights by compelling the ratable production of gas. The part of the law relative to withdrawal of sweet gas became effective Aug. 1, 1935, and the part referring to withdrawal of sour gas became effective Oct. 1, 1935. Three of the major pipe line companies attacked the validity of the ratable production feature of the new law and a preliminary injunction was granted by the Federal District Court. The final hearing on the incrits of the case is scheduled for the early part of January. Natural Gasoline.—Forty of the 42 natural-gasoline extraction plants in the Panhandle operated throughout the year. One plant discontinued

Jan 1, 1936

By T. C. Craig

During the year, there were 570 oil wells completed for a total daily initial production of 365,352 bbl. The daily oil potential of the field, effective Jan. 1, 1935, as established by the Texas Railroad Commission, was 306,102 bbl. with a daily allowable of 58,800 bbl., whereas, on Dec. 31, 1935, the potential was 587,376 bbl. with a daily allowable of 57,800 bbl. Because of the limited market demand, the allowable decreased although the potential increased. In August, the five-day test for determining the potential production of a well was replaced by a 24-hr. test. The reason for this change was that some of the oil-pur-chasing companies contended that too much oil in excess of the limited market demand was produced during the five-day tests. Dry Gas.—During July, the Texas Railroad Commission supervised the first complete and accurate field-wide test of open flows that has been made in this area. The total open flow as determined at that time was 16,426,085,000 cu. ft, There were 79 gas wells drilled in '935, with a combined open flow of 2,408,000,000 cu. ft. and 50 depleted oil wells were plugged back for gas with a total open flow of 529,800,000 cu. ft. The total new gas production for the year was, therefore, 2,937,800,000 cu. ft. The 17 natural-gas pipe lines drawing on the Panhandle supply of fuel gas withdrew a daily average of 420,497,507 cu. ft., or a total of 153,481,-590,000 cu. ft. for the year. The 44th Texas Legislature passed a statute known as House Bill No. 266, which was designed to prohibit waste and protect correlative rights by compelling the ratable production of gas. The part of the law relative to withdrawal of sweet gas became effective Aug. 1, 1935, and the part referring to withdrawal of sour gas became effective Oct. 1, 1935. Three of the major pipe line companies attacked the validity of the ratable production feature of the new law and a preliminary injunction was granted by the Federal District Court. The final hearing on the incrits of the case is scheduled for the early part of January. Natural Gasoline.—Forty of the 42 natural-gasoline extraction plants in the Panhandle operated throughout the year. One plant discontinued

Jan 1, 1936

By Ashok K. Kakar

THE occurrence of superplasticity in Al-Zn alloys is of interest because of its possible industrial exploitation.' The eutectoid composition (78Zn-22A1) has been the most extensively studied;'-= neck resistant flow and high strain rate sensitivity of flow stress (characteristic of superplasticity) are associated with a micron-size grain conferred on the alloy by an homo-genization and quench.5'6 Compositions away from the eutectoid have received comparatively little attention, especially from the viewpoint of relating the structural

Jan 1, 1969

By E. H. Wells, A. Andreas

The oil and gas industry of New Mexico recorded notable progress ill 1935. More wells were brought in than in any previous year, and important new discoveries were made. The total number of completions was 340, of which 260 were oil wells, 8 were gas wells and 72 were dry holes. The total oil production was 20,228,947 bbl., an appreciable increase over the 1934 production of 16,636,804 barrels. Many of the wells completed in southeastern New Mexico were acidized. This treatment proved highly effective in increasing the capacity of the wells, the resulting potentials usually being two to ten times as large as before acid treatment. In the Lea County fields in which proration was entirely on an acreage basis, the tendency of many of the operators was to complete their wells according to best conservation practice rather than to obtain the largest possible potential. Much remedial work was done in the Hobbs, Cooper, Jal and Eunice fields, and with excellent results. At many of the wells high gas-oil ratios were greatly reduced and encroaching waters shut off by setting packers. Several companies carried on pretentious geophysical campaigns in the southeastern part of the state. The location of the Amerada discovery well in the Monument field was based on geophysical surveys. The New Mexico Oil Conservation Commission, established by the 1935 Legislature and consisting of the Governor, the Commissioner of Public Lands and the State Geologist, began to function in May. Production in the state thereafter was based on orders issued by the Commission. Proration in the Hobbs field, which had been provided for since July, 1930, by successive proration agreements signed by all operators in the field and approved by the State Geologist, was continued by the Commission by giving approval to the current proration agreement,. A plan of proration for the other Lea County fields that had been in offect since early ill 1934 was adopted. 111 September, 1935, the Commission approved a. proration agreement for the Artesia-Jackson-Maljarnar area in Eddy and Lea counties that had been agreed upon by

Jan 1, 1936

By H. W. McCue, Henry Rogatz

Oil.—In the Texas Panhandle, 502 oil wells were drilled during the year 1940, with a total daily initial production of 139,187 bb1.—that is, 137 more oil wells drilled than in the previous year, with an increase in total daily initial production of 8219 bbl. The total daily potential of the field on Dec. 31, 1940, as determined by the Texas Railroad Commission, was 1,375,502 bbl., an increase of 30,825 bbl. over the previous year. On Dec. 31,1940, a daily allowable of 85,050 bbl., which was a decrease of 35 per cent over 1939, was assigned to the field to be produced from 4788 wells. The total amount of oil produced for the year was 26,788,590 bbl., making a cumulative total of 378,960,728 bbl. during the past 19 years. No new oil-producing acreage was discovered. Gas.—During the year, 92 gas wells were drilled, having a combined open flow of 2,402,900.000 CU. ft.; that is, 6 more than the number of wells drilled in 1939, with an increase in the open flow of 204,900,000 cu. ft. per day. The gas production for the year was 670,435,112,000 CU. ft., and the total gas removed from thc ground during

Jan 1, 1941

By Henry Rogatz, H. W. McCue

Oil.—In the Texas Panhandle, 502 oil wells were drilled during the year 1940, with a total daily initial production of 139,187 bb1.—that is, 137 more oil wells drilled than in the previous year, with an increase in total daily initial production of 8219 bbl. The total daily potential of the field on Dec. 31, 1940, as determined by the Texas Railroad Commission, was 1,375,502 bbl., an increase of 30,825 bbl. over the previous year. On Dec. 31,1940, a daily allowable of 85,050 bbl., which was a decrease of 35 per cent over 1939, was assigned to the field to be produced from 4788 wells. The total amount of oil produced for the year was 26,788,590 bbl., making a cumulative total of 378,960,728 bbl. during the past 19 years. No new oil-producing acreage was discovered. Gas.—During the year, 92 gas wells were drilled, having a combined open flow of 2,402,900.000 CU. ft.; that is, 6 more than the number of wells drilled in 1939, with an increase in the open flow of 204,900,000 cu. ft. per day. The gas production for the year was 670,435,112,000 CU. ft., and the total gas removed from thc ground during

Jan 1, 1941

By P. K. Kaiser, C. Mackay

A circular shaft with a diameter of 6m was excavated by the conventional drilling and blasting method to a depth of 235m through 60m of glacial till, 1 Om of water bearing basal sand, 1 1 Om of clay shale (Bearpaw Formation) and finally a strata of coal, mudstone, siltstone and sandstone (Oldman Formation). The lined shaft was instrumented at three levels by multipoint extensometers to determine the displacement field near the shaft bottom, embedment strain gauges to measure the strains in the liner and IRAD-stress change gauges to observe the radial and tangential stress changes in the rock mass. The data from these gauges were used to determine the in situ stress field. An attempt to measure in situ stresses by overcoring was also made at a higher elevation. The performance of the shaft and its support was then evaluated by use of the "Convergence-Confinement Method". For this purpose the measurements of stress changes and displacements were combined to determine by extrapolation the displacements ahead of the shaft and after the liner installation. The convergence curves calculated in this fashion were then used to evaluate the performance of the cast-in-place concrete liner and of an alternate shotcrete shaft support system.

Jan 1, 1983