Search Documents

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wil-barger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1940 The encouraging outcome of exploration and development in Montague and Cooke Counties and generally greater activity throughout the district resulted in the drilling of some 1700 wells during 1940, about 350 more wells than were drilled in 1939. Approximately 1250 of these tests were completed as oil wells. Production likewise increased during I940 to the extent of 8 million barrels more than the 25 1/2 million barrels produced in 1939. In spite of this large increase in production, known oil reserves again increased substantially. As is usually characteristic of this district, the new reserves were from a large number of fields, none of which were of such magnitude as to be important to the oil industry. Nevertheless, the Fargo field, Wilbarger County, deserves mention as one of the more important discoveries in this district during 1940. Following seismic surveys, the hmerada Petroleum Corporation located its No. I Goodpasture in sec. 35, block IS, H. and T. C. R. R. Co. survey, and drilled it to a total depth of 6717 ft. This well was completed in July 1940 through perforations in the casing from a pay between 3230 and 3252 ft. for an initial production of 241.5 bbl. on an 8-hr. pumping test. Other potential producing horizons were found in the Pennsyl-vanian at depths of 3960 to 3995 ft., 4208 to 11.234 ft., 4407 to 4422 ft., and in the Ordovician at 6300 ft. Wells completed to date in the several Pennsylvanian horizons have an average daily potential of 600 bbl. of oil. Although no wells have yet been completed in the Ellenburger dolomite (Ordovician), the discovery well swabbed I5 bbl. per hour from this formation before plugging back for completion in an upper horizon.

Jan 1, 1941

By Henry M. Howe

in Cast-Iron. It has been generally accepted that the presence of silicon in cast-iron leads to the formation of graphite; and this has been explained by saying that the silicon lowers the solvent power of iron for carbon at and somewhat below the freezing-point, so that, in the presence of silicon, the iron is unable to retain in solution or combination the whole of the carbon with which it has united while molten, and therefore expels the excess of carbon in the form of graphite, during and immediately after solidification. Probably the best way to study this question would be to examine pure cast-irons, i.e., those containing nothing but iron, carbon and silicon, which at the same time should have been saturated with carbon when molten. But the data for such a study are not at hand; so we must turn to commercial pig-irons as they are made in the blast-furnace, and before their composition has been changed by remelting. Much evidence has been offered of late, tending to oppose the theory of the action of silicon above set forth. Some of this evidence will be examined here. 1. Mr. Bachman's Results. In particular, Mr. F. E. Bachman† has published a collection of analyses of cast-iron, in which the proportion of graphite at first appears to be nearly independent of the proportion of silicon present. Thus, in his Table LI., we find that with pro-

Jan 1, 1901

THE education of adolescents to perform the duties and assume the responsibilities of maturity has been a characteristic of human society since the dawn of history. In the beginning the members of the immediate family performed this function, and in modern life they still have an important part in it. Possibly religion was the first field in which education began to be functional; young people were sent for instruction to a teacher who had a broader and deeper knowledge of the subject than was possessed by the family. It does not seem necessary for our purpose to attempt to determine how, when, or where instruction in the practical arts first began to become functional, and the brief outline which follows must suffice. The discovery and utilization of mineral substances to improve and maintain the conditions of human living is a practical art, which must have had an almost accidental origin and have been developed by empirical experiments. We do not know, nor would it be useful to try to fancy, how men first learned that they could make use of mineral substances to their benefit, but however that knowledge was initially gained it was certainly trans- mitted through instruction in the family. At fist such activities must have been merely a minor part of the making of a living, bit in time those who excelled found it better to devote them-

Jan 1, 1941

By Charles C. Hawes

DETERMINATION OF SILICA OXIDE iron ores usually are found in intimate association with silica and phosphorus compounds. Their quantitative separation and purification sometimes present difficult problems to the chemist. Silicic acids may represent various degrees of dehydration. They are exeedingly weak, but combine with metallic oxides and form some of the most stable oxides in nature, the silicates. When iron ores are treated with hydrochloric acid, they yield practically all their iron. However, apart from rare exceptions, varying amounts of insoluble residues of silica, alumina, lime, magnesia and compounds of phosphorus, sulphur, titanium, chromium and others will be left. If the oxides of silicon, aluminum and titanium are present in small quantities, the insoluble residue is generally very small, but the presence of these oxides is more usual in larger quantities. Therefore, only a special treatment can break the bond between these elements. Ore Residues Acids remove the soluble constituent of the ore, leaving the insoluble residue, which chemically is rock or gangue and must be treated accordingly. Alkali carbonates are used frequently to break up the residue, but other fluxes have also been recommended, such as a number of lead and boron salts. The introduction 0f these salts, which offers certain advantages, requires, however, their removal before the other constituents can be analyzed, and this elimination is sometimes difficult. Usually in quantitative analysis silicates are dissociated by fusing them in a platinum crucible with sodium carbonate, thereby forming sodium silicate, Na2SiO3, sodium aluminate, Na2Al204, sodium titanate, Na2TiO3, and carbonates of other elements. All the carbonates are soluble in hydrochloric acid, but also some silicic acid is formed that must be rendered insoluble. To this end the solution is evaporated several times, as the first evaporation still leaves as much as 5 per cent of the silica soluble. Even after a number of evaporations, minute quantities of silica may be found with the iron and alumina present. Perchloric Acid as an Agent for Dehydrating Silicic Acid Perchloric acid, HC104, (60 per cent), has been used for years as a solvent, but few chemists have used it to dehydrate silica. It is derived from anhydrous perchloric C1207, which is most unstable and dangerous. Perchloric acid is a strong oxidizing agent, which boils at 203°C. It is more effective in rendering silica insoluble than any other known agent, and most rapid in action. After perchloric acid is added to a mixture containing silicic acid, the resultant solution is

Jan 1, 1945

By F. F. Craig

The authors have done a commendable job in combining a number of recognized waterflood performance prediction methods into one composite method. The availability of a FORTRAN program for this composite method should encourage its widespread industry use. Pan American has had a computer program developed along similar lines for a number of years,' and it has received more use than any other reservoir prediction method. In three important stages of a pattern waterflood, the authors fail to consider fully the effects of water-oil mobility ratio on performance. This is discussed in the following paragraphs and modifications of the prediction method are suggested. During the early stages of a waterflood in a partially depleted formation, the injected water and its preceding oil bank move out radially from the injection wells. As pointed out in the author's paper the method of Yuster and Calhoun2 or predicting the water injection rate during this period assumes that the mobilities of the water and oil are equal. In his book, Muskat3 resents a modification of the Yuster-Calhoun approach that considers fully the influence of water-oil mobility ratio. In Muskat's method, the prediction of the injection rate-injected volume-time relationship is expressed in readily programmed dimension-less unts. At and following fillup the five-spot pattern consists of a water-invaded pattern with the remainder of the pattern containing only oil and connate water. In the paper, Eq. 18 is used to calculate the water injection rate at fillup. This equation considers that the entire pattern is invaded by water. To properly consider both the incomplete areal sweep of water and the water-oil mobility ratio, Eq. 18 should read:

Jan 1, 1969

By E. W. Davis

Iron-ORE beneficiation methods are determined largely by blastfurnace requirements. There are still many millions of tons of direct furnace ore in the Lake Superior district and blast furnaces are designed and operated for the most efficient use of this material. Beneficiated ore must be so prepared that existing furnaces may use it without alteration in design or radical changes in practice. Many attempts have been made to develop new furnaces or processes for smelting iron-ore concentrate not suitable for blast-furnace use, but these processes have gained little importance. It is, therefore, the endeavor in beneficiating iron ore to make a product that will give at least as good results as direct furnace ore in existing blast furnaces. The term "beneficiation," as applied to iron ore, does not necessarily mean concentration, but more accurately means "dressing up" the ore so that it is more acceptable to the blastfurnace operators. In modern blast-furnace practice the structure of the ore is quite as important as the chemical analysis. Certainly, the higher the iron content and the lower the silica, phosphorus and sulfur, the more desirable the ore bccomcs; but if the structure is bad, that is, if the blast-furnace gases can penetrate the charge only with difficulty, the ore is undesirable regardless of its analysis. This means that the ore should be as uniform in size as possible and free from fines, and also that the individual particles of ore should be pervious to the reducing gases of the furnace. Structure and purity are the primary requirements for a furnace ore and structure is just as important as purity. Iron-ore beneficiation processes can be divided, therefore, roughly into two main classifications: (1) processes that primarily improve the structure, and (2) processes that primarily improve the chemical analysis. During the past 10 years approximately 25 per cent of the ore shipped from the Lake Superior district has been beneficiated. Of this about half has been crushed and screened, a simple operation that primarily improves the structure but in some cases also improves the analysis slightly. The other half of the shipment of beneficiated ore, amounting to an average

Jan 1, 1935

By Charles C. Hawes

DETERMINATION OF SILICA OXIDE iron ores usually are found in intimate association with silica and phosphorus compounds. Their quantitative separation and purification sometimes present difficult problems to the chemist. Silicic acids may represent various degrees of dehydration. They are exceedingly weak, but combine with metallic acids and form some of the most stable oxides in nature, the silicates. When iron ores are treated with hydrochloric acid, they yield practically all their iron. However, apart from rare exceptions, varying amounts of insoluble residues of silica, alumina, lime, magnesia and compounds of phosphorus, sulphur, titanium, chromium and others will be left. If the oxides of silicon, aluminum and titanium are present in small quantities, the insoluble residue is generally very small, but the presence of these oxides more usual in larger quantities. Therefore, only a special treatment can break the bond between these elements. Ore Residues Acids remove the soluble constituent of the ore, leaving the insoluble residue, which chemically is rock or gangue and must be treated accordingly. Alkali carbonates are used frequently to break up the residue, but other fluxes have also been recommended, such as a number of lead and boron salts. The introduction of these salts, which offers certain advantages, requires, however, their removal before the other constituents can be analyzed, and this elimination is sometimes difficult. Usually in quantitative analysis silicates are dissociated by fusing them in a platinum crucible with sodium carbonate, thereby forming sodium silicate, Na2SiO3, sodium aluminate, Na2A1204, sodium titanate, Na2TiOs, and carbonates of other elements. All the carbonates are soluble in hydrochloric acid, but also some silicic acid is formed that must be rendered insoluble. To this end the solution is evaporated several times, as the first evaporation still leaves as much as 5 per cent of the silica soluble. Even after a number of evaporations, minute quantities of silica may be found with the iron and alumina present. Perchloric Acid as an Agent for Dehydrating Silicic Acid Perchloric acid, HCI04, (60 per cent), has been used for years as a solvent, but few chemists have used it to dehydrate silica. It is derived from anhydrous perchloric C1207, which is most unstable and dangerous. Perchloric acid is a strong oxidizing agent, which boils at 203°C. It is more effective in rendering silica insoluble than any other known agent, and most rapid in action. After perchloric acid is added to a mixture containing silicic acid, the resultant solution is

Jan 1, 1945

H. 0. HOFMAN, Boston, Mass (written discussion*).-The paper by Mr.. Pyne gives clear evidence of the difficulties the metallurgist is likely to encounter when he tries to recover in the blast furnace the metal from old chromite lining used as a refractory material in the copper reverberatory furnace. It appears that chromite cannot be fluxed at temperatures which usually prevail in copper blast furnaces. This calls to mind the freezing-point curve drawn by M. Simonis1 of mixtures of chromite and kaolinite. The chromite used in the experiments contained 52.9 per cent. Cr203, 22.6 FeO, 4.8 AI203, 9.6 Si02, .10.1-MgO; FIG. 1. the kaolinite was clay from Zettlitz with 98.5 per cent. clay-substance: The accompanying curve shows that the eutectic mixture with 35 per cent. kaolinite and 65 per cent. chromite freezes at Seger cone No. 15 (1435° C.), while kaolinite fuses at cone No. 35 (1770° C.) and chromite at cone No. 42 (2000° C.). The curve indicates that the difficulty in the blast furnace can be overcome by having at the smelting zone a temperature much higher than is usual in copper smelting; a charge composition similar to that prevailing at the Mansfeld copper smeltery -which gives with 23 per cent. coke a, slag of the composition Si02, .49.09; .(FeMg)0, 5.58; (CaMg)0, 16.02; A1203,-16.02-might flux and fuse chromite.

Jan 3, 1918

By B. H. Kear

All the possible ways of forming simple two-dislocation boundaries in multiple slip orientations are deduced. It is shown that the principal differences in work hardening behavior of crystals plastically deformed in these orientations can he accounted for in terms of the likelihood of formation of diffuse boundaries, or deformation bands, consisting of the products of dislocation reactions of the Lomer type. Also, it is pointed out that the break-up of boundaries under the applied stress is more likely to yield interstitial jogs than vacancy jogs, whereas glide dislocations cutting throuqh dislocations trapped in particularly stable boundam'es can acquire both types of jogs. USING Frank's' grain boundary formula, Ball and Hirsch2 determined the parameters of all the possible boundaries that can be built from two sets of glide dislocations in the fee structure. This paper deduces the geometrical possibilities for the formation of these two-dislocation boundaries in the different multiple slip orientations, and discusses the role of boundaries in work hardening and in jog formation. Formation of Two-Dislocation Boundaries in Mutiple Slip Orientations. The parameters of the possible two-dislocation boundaries for any crystal orientation can be deduced most conveniently using the boundary formulae due to Amelinckx,3 in conjunction with the stereographic projection shown in Fig. 1. Suppose that slip occurs in a-BC and ß-CA. According to Amelinckx, when the two systems of glide dislocations are parallel, the rotation axis, u, of the boundary is parallel to (a x ß) and the unit normal, u, defining the boundary plane is parallel to (a x ß) x (BC x CA). On the other hand, when the glide dislocations form a crossed grid, u is parallel to (BC x CA) and u is parallel to (a x CA) x (ß x BC). In Fig. 1, (a x ß) is the pole of the great circle passing through a and ß, so that u is parallel to DC, i.e., parallel to [110]. Furthermore, (a x ß) x (BC x CA) is the pole of the great circle passing through DC and 6, so that u is parallel to [110]. Hence, when all the glide dislocations are parallel, the boundary is pure tilt with parameters u = [110], v = [ 110]. Similarly, it may be shown that the corresponding crossed grid of dislocations is a mixed boundary with u = [111], u = [111]. Consider the case of a crystal compressed in the [001] orientation. In this orientation, according to Fig. 1, there are eight available slip systems. In what follows, the different types of two-dislocation boundaries that are possible in this orientation will be examined by taking different combinations of two slip systems out of the available eight, with a-BC always one of the systems. Case (i)—Slip Systems a-BC and d-CB. The formation of a tilt boundary in (101), which consists of a crossed grid of edge dislocations with vectors BC andCB, is illustrated in Fig. 2(a). As the figure shows, slip is required in the system a-BC in one part of the crystal and in d-CB in the other part, with both sets of dislocations entering the boundary from opposite sides. The rotation axis of the boundary lies in (101), depending on the relative densities of the two sets of edge dislocations in the boundary. Case (ii)-Slip Systems a-BC and ß-CA. The two possible boundaries are shown in Figs. 2(b) and (c); boundary (b) is tilt with u = [110], u = [110], and

Jan 1, 1962

By P. W. Neurath, R. E. Waite

INFORMATION is available on the effect of stress on permeability, coercive force, and hysteresis for a variety of materials' but for the technically important grain-oriented 3 pct Si-Fe' the stress effects are not adequately covered in the literature; in addition, most of the stress data do not permit estimation of what would happen to the 60 cycle watt losses of the material under stress. Direct measurement of these effects therefore has been made and appears to be of considerable theoretical as well as practical interest. Losses were measured on the central 25 cm portion of 40~3~0.035 cm samples which could be stressed in a small tensile machine built for this purpose. Under tension the following effects, illustrated in the figures by a particular example, were observed: 1—"Unstrained" material of commercially acceptable loss level shows no change or a small increase in loss at low elastic stresses. For the sample shown in the figures, this is illustrated during the initial run, where a 7 pct increase is observed (Fig. 1). 2—There is no additional change in loss when the sample is further strained up to the elastic limit (Fig. 1). Within that limit the loss-stress curve is reversible. This is not illustrated in Fig. 1. 3—Even in the plastic range only small increases in loss are observed as long as the sample is kept under stress (Fig. 2, point N); often no increase can be observed (Fig. 1). 4—A large increase in watt losses is observed after removal of the stress subsequent to plastic deformation (Figs. 1 and 2). 5—All, or nearly all, of the foregoing increase in loss due to plastic deformation can be eliminated by a reapplication of tensile stress but returns upon removal of this stress. This is illustrated in the third run (Fig. 3). This run remains within the elastic limit and shows the reversibility of the stress-loss curve under this condition. These findings have been confirmed on large Samples (approximately 200~10~0.035 cm and larger) except that under 1 no initial increase in loss was ever observed on these. The accuracy of the watt loss measurements is of the order of 1 pct. Neither bending of the sample in the tensioning device nor a redistribution of flux along the width of the sample accounts for these results. They therefore must be explained on the basis of either a change in the domain configuration due to stress or a change in the domain wall mobility. Acknowledgment The assistance of Mr. Robert L. TenBroeck with the instrumentation is gratefully acknowledged.

Jan 1, 1956

By Vytas Svalbonas

Sophisticated computer analysis methods such as finite elements, finite differences, and numerical integration have become tools in the mineral processing industry for design of large mill shells. While use of such methods allows the analyst-designer to take new freedom with his designed structure, there are also pitfalls and dangers which must be recognized for the proper use of such sophisticated tools. One of the worst of these is treating any computer answers as "gospel truth." The present paper discusses the knowledge required by the analyst-designer for proper use of computer analysis, as well as explaining to the layman how to identify questionable areas in such structural analyses.

Jan 1, 1980

By K. C. Sclater, B. R. Stephenson

Recent progress in oil-recovery methods has brought into prominence gas-energy relations in oil sands. The greater the effort made to utilize this gas-energy relationship to the best advantage in oil recovery, the greater becomes the need for more precise information concerning physical conditions as they actually exist in an oil well. The intelligent use of gas-oil ratios when considering production efficiency has been the subject of much recent discussion. It has been stressed that the pressure as well as the volume of gas must be known when considering the efficiency of a producing well on an energy basis. When methods of production are compared on an energy basis it implies a knowledge of pressure, temperature and physical properties of the fluids at the bottom of the well. In questions concerning gas-lift and the pressure control of wells usually there is a wide variance of opinion among engineers when energy relations come up for discussion. Perhaps this difference f opinion can be traced to erroneous assumptions made with regard to the physical conditions existing within the well. If erroneous assumptions are made it follows that computations based on these assumptions will give results which also will be in error. That erroneous assumptions are made is not to be wondered at because when handling a fluid composed of gas and oil, we are dealing with a complexity of hydrocarbon components each varying to some degree in physical and chemical properties. This means that the physical state of the gas and oil will depend not only on temperature and pressure but that it will be influenced also by the relative amounts of the various hydrocarbon components present. If water is present the problem becomes still more complicated. From these considerations alone it would appear that we can well afford to give some thought to devising more positive methods or means for obtaining data on physical conditions within the well rather than depend entirely on computations from casinghead data. If these data

Jan 1, 1929

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland' found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.' determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-' torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.' These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren' and Miller' were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

By R. M. Daelen

In recent years many new appliances have been introduced into German steel-works and rolling-mills for the purpose of improving working-methods, and of creating and maintaining increased production, and satisfying the ever-growing demand for metal of closely specified hardness, strength and form. One result of the improvements has been to aid very effectively in demonstrating the real superiority of ingot- over wrought-iron for almost every possible purpose, and in dispelling the last vestiges of prejudice unfavorable to the new metal. If, nevertheless, no marked decrease in the number of puddlingfurnaces has yet been noticed, the cause of their survival must be attributed to the greatly increased consumption of all kinds of ironmanufactures. Several large new works for the production of ingotiron are now, however, in course of erection in the Rhenish-Westphalian district, and upon their completion a rapidly diminishing output of wrought-iron may be anticipated. The present aim of all large works manufacturing ingot-iron is to work the molten blast-furnace pig into a finished product without any further fuel-consumption than is required to furnish steam for the rolling-mill. Though practice has established the feasibility of this principle, no works can yet point to its complete adoption, partly because of the limitations imposed by existing conditions and plant, and partly, also, on account of the highly-diversified character of the finished products. The Bessemer-works were the first to feel the influence of the basic process; but of recent years a similar influence has affected the open-hearth, and the owners of works possessing both a converterand an open-hearth plant are now seeking to arrange them for combined working, in charging as well as in casting. In small works the basic-lined reverberatory furnace is constantly gaining ground over the old puddling-furnace. The small basic converter, on the

Jan 1, 1891

By D. F. DeSante, A. S. Tetelman

MICROCRACKS are often introduced into commercial metals during fabrication processes such as swaging, cold rolling, deep drawing, and welding. These microcracks act as strain concentrators and may be capable of causing premature catastrophic failure of a component or weld. The present investigation was undertaken to determine whether high-temperature annealing treatments may be capable of reducing or negating the detrimental effects of such existing microcracks. Internal microcracks, ranging from 0.1 to 0.85 mm in length and averaging 0.23 mm, were introduced into polycrystalline Fe-3 pct Si tensile specimens (0.155 mm grain size) by the cathodic charging of hydrogen.1'2 The typical appearance of such microcracks and their associated strain patterns (made visible by the technique of dislocation etch pitting3) is shown in Fig. 1. The stress fields of the dislocation loops formed during plastic relaxation stabilize the microcracks so that, when the internal hydrogen pressure is removed: the microcracks stay open, rather than disappear as perfectly elastic cracks would be expected to do.' As shown in Fig. 2, such stopped microcracks cause a 36 pct decrease in the macroscopic cleavage fracture strength at -196°C.

Jan 1, 1969

By A. J. Opinsky

MANY investigators, in their discussions, have reasoned that the ductile-brittle transition in iron could be explained by the intrusion of cleavage into the normal slip process. The purpose of this note is to apply the laws of critical normal stress for cleavage and critical shear stress for slip to explain the orientation and temperature dependence of the ductile-brittle transition in body-centered cubic metals. It will be found that within a certain temperature range, single crystals tested in tension will cleave or slip, depending on their orientation. Some data recently appearing in the literature will be analyzed from this standpoint. For a single crystal with [uvw] parallel to the tensile axis, the resolved shear stress on the slip

Jan 1, 1954

By Charles O. Thomson

When a wire rod of iron or of steel is immersed in a hot solution of common salt, allowed to remain long enough to bring the metal to the temperature of the brine, and withdrawn, the surface of the rod is irregularly covered with a deposit of crystals of salt. These crystals adhere to the cod with great firmnes, in consequence, doubtless, of a thin film of ferric hydrate, which is formed between them and the rod as the water dries off. The rod can now be reduced, by successive passes through a dic or draw-plate, without any

Jan 1, 1881