Search Documents

By R. J. Wygal, J. Naar

An equation for three-phase (water, oil, gas) imbibition oil permeability is developed, assuming the water to be the dominant wetting fluid. Oil isoperms are obtained for consolidated sandstones characterized by 1/pc2 = CS*. The evolution of an oil-gas system imbibing water from Swi to(Sw,imb )max is shown to proceed along a line of constant oil saturation with increasing oil permeability and decreasing gas saturation. When the gas satuation cannot be reduced further, the system evolves along a line of constant Sg with decreasing oil saturation and permeability. The initial gas saturation is shown to reduce markedly the effect of complete wetting by either oil or water on flow performance. INTRODUCTION Imbibition oil isoperms are required for performance prediction when a well is producing water, oil and gas. This situation occurs in multiphase displacements such as underground combustion, steam injection and the water flooding of highly depleted reservoirs. In a recent paper,1 a model was presented for the prediction of two-phase imbibition characteristics. This paper extends the imbibition model to the case of three phases by assuming that the water is the dominant wetting fluid. The following results were obtained from the model: (1) an analytical expression of oil isoperms; (2) oil isoperrns as functions of reduced water, oil and gas saturations, valid for all sandstones having a capillary pressure curve which can be approximated by 1/PC = CS*; and (3) evaluation of the three-phase flow performance as dictated by complete wetting by either oil or water. The agreement between predicted and observed oil recovery in the presence of a gas phase, reported in Ref. 1, is a partial support for the present development. However, experimental data are not available at this time to check fully the model predictions. Perhaps this paper will stimulate the collection of such data. The imbibition model of a porous medium has been described previously, and the reader is referred to the paper of Naar and Henderson1 for details. In brief, the model is formed by the random interconnection of straight capillaries, with a provision for the blocking of the non-wetting phase by the invading wetting fluid. The following expressions were derived from the model. 1. The amount of oil blocked by the invading water is

By M. Karfakis, K. Kim, R. V. de la Cruz

The in situ deformability of a closely jointed basalt rock mass was determined by two different methods: the NX-borehole jack method where displacements of opposing curved platens were related to applied hydraulic pressures, and the modified Goodman jack method where tangential strains on the borehole walls were related to induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX-borehole jack method. To explain the discrepancy, the influence of fractures and test variables, such as depth, orientation, hole location, and applied pressure on the calculated modulus of the rock mass, were analyzed by factorial analysis. It was found that the orientations and measurement depths have statistically significant effects. The in situ deformability values obtained by nonlinear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1984

By M. E. Steidlitz

FABRICATION of semiconductor devices.requires the formation of electrical contacts, often involving the use of lead, tin, and lead-tin solders. In several recent instances when germanium had been bonded to nickel with lead, a new metallic phase appeared, unattached to either germanium or nickel, but rather suspended as a continuous foil wholly contained within the lead matrix. Since such metallic structures do not form in nickel-lead or lead-germanium systems under identical conditions, a brief study was made of the characteristics and possible formation mechanisms of this material. EXPERIMENTAL Specimens were prepared by placing single crystal, transistor-grade germanium discs, 30-mils in diam by 6-mils thick, into a depression in a graphite boat. =A* nickel washers, 125 mils in diam by 5-mils thick, containing a center hole of 10-mils diam, and coined into a soup bowl shape, were loaded on top of the discs, so that the bottom of the

Jan 1, 1959

By Dorsey Hager

THE possibilities of finding new oil pools in Oklahoma and Kansas are far from promising. In 1916, the only new pools of importance were the Franchot pool near Bixby, the Garber, and the Billings pools in Oklahoma, and the Virgil and Utopia fields in Greenwood County, Kansas. In the first 8 months of 1917, a small pool of unknown extent was opened south of the Stone Bluff pool in Oklahoma, and a pool near Casey, Paunee County, Oklahoma. In Eastern Kansas, interest has been. caused by the sinking of new wells near the old Iola pool, but nothing of magnitude has yet been found. The outlook for new pools is far from encouraging, especially as geological surveys have covered all of Oklahoma and Kansas. There are a few areas where geological surveys throw little or no light on the subject, as exposures are poor, but the chances of finding new pools in such areas are slight indeed, if one can judge from the past history of such areas. So far the geologists have based their opinions largely upon the presence or the absence of geologic structure, such as anticlines, domes, and terraces, but some pools will most certainly be found where no surface structure exists, but where local changes in the sand body favor oil accumulations. However, the possibilities of new pools off structure are small, as fully 90 per cent. of the oil pools are on definite structure. In the past, it is estimated that one test in 150 "wild cats" or new tests has brought in a new field. The writer feels safe in asserting that the proportion will decrease still further, so that but one out of 500 new tests may bring in a pay well in a new area. From now on the principal field of work in Oklahoma and in Kansas will consist in developing the present pools. The years 1915, 1916 and 1917 saw the high peak of Oklahoma and Kansas oil production. The Eldorado and the Augusta oil fields present the largest possibilities for continued production in Kansas. These two pools have been scarcely more than one-third developed, and have greater potentialities than any of the present Oklahoma pools. In Oklahoma, pools of magnitude should

Jan 10, 1917

By Wayne E. Glenn, R. W. French, Lincoln F. Elkins

The Lance Creek Sundance reservoir provides a case history of ro years performance of a reservoir in which unit operation has permitted effective utilization of gravity drainage augmented by primary pressure control with injection of gas into top structural wells. Detailed performance of the reservoir is presented by means of maps of Well status, reservoir pressure, individual well recovery, etc., and by pool-performance charts. Analysis of reservoir performance indicates only minor water encroachment, so that gravity, injected gas, and expansion of gas are the main oil-expulsive agents. A simplified theory of regional drainage of oil from upstructure location to downstructure location due to gravity is presented and checked by means of comparison of "reservoir" permeability and "well" permeability from the pool performance. Good order of magnitude agreement was obtained. Individual well performance and overall reservoir performance indicate possibility that maintenance of pressure makes ineffective those parts of the reservoir in which permeability is too low to permit effective drainage of oil by action of gravity. Oil from these parts can be recovered only when pressure is reduced locally by selective withdrawal or when overall reservoir pressure is finally reduced.

Jan 1, 1949

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

By W. Rostoker

PART of a program of research on the Ti-A1 system1 involved a study of the lattice parameters of the titanium-rich a solid solution, which has a hexagonal close-packed structure. For this work, a 14 cm Debye-Scherrer powder camera and filtered CuK, radiation was used. For each pattern, the parameters were calculated by a least squares solution of the five strongest high angle lines. This provides an accuracy of i0.005A or better. The results are shown graphically in Fig. 1. It will be seen that an unusual change of slope occurs in the curve for the C parameter at high aluminum contents. Such anomalous changes in slope have been recorded by RaynorV or several magnesium-rich solid solutions. The effects were interpreted in terms of a special contribution to the lattice distortion due to factors of electronic origin predicted by Jones." Jones' theory, in substance, suggested that an unusually large expansion of the lattice would begin when the electron per atom concentration in the alloy was increased to a value at which an overlap just began from one Brillouin zone to another. Con-

Jan 1, 1953

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably her product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too he, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater dificulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1947

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably her product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too he, since finer particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely fine kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater dificulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1947

By A. Arrott, G. S. Ansell

A model is proposed to account for the observed strengthening behazlior of ferrous martensites. me model is based upon the inheritance of carbon-rich regions by the martensite which were present in the FERROUS martensite is formed by a nucleation and shear mechanism when austenite is cooled, at a rate which is fast enough to suppress the formation of pearlite, below a critical temperature (Ms ). Although the mechanism of the transformation process appears to be well understood,1,2 the mechanism re- austenite prior to transformation. These carbon-rich regions strengthen the martensite in a manner analogous to the strengthening effect due to a finely dispersed second phase. sponsible for the observed high strengths exhibited by ferrous martensites is uncertain. In this paper, a model is proposed to account for the strengthening of ferrous martensite. MODEL The maximum solubility of carbon in austenite is 1.98 wt pct as compared with a maximum solubility of 0.025 wt pct in ferrite. Prior to transformation, the carbon in the austenite is nonuniformly dis-

Jan 1, 1963

By L. G. Truby

DISCUSSION By Rhrt G. Nisle, Phillips Petroleum Co., Barthesville, Okla. The subject paper presents the results of a reservoir behavior analyzer study of the pressure-production performance of five Ellenburger pools in West Texas. These five pools are Wheeler, TXL, Andector, Embar, and Martin. This laboratory has also made reservoir behavior analyzer studies in this area and arrived at substantially the same conclusions. Although the principal results of the studies made in this laboratory are confirmed by the results in the subject paper, there are certain points of difference. The points of difference are (1) the subject paper includes the Martin pool in the common aquifer, whereas our studies indicate that it is not, and (2) the subject paper concludes that the effective aquifer is considerably smaller than that derived from studies made in this laboratory. In terms of reservoir analyzer data, our rejection of Martin is based on the inability to obtain a satisfactory match of the pressure curve when Martin is considered as lying within the common aquifer. A satisfactory match was possible, however, when Martin was run as an isolated pool. This indicates that the pressure disturbance resulting from production at Martin had not reached Embar, Andector, TXL, or Wheeler at the time of our study. A similar situation exists relative to Dollarhide. In tern of geological data, our rejection of Martin is based on the presence of a faulted zone between Martin and Embar. This condition is indicated in Fig. 4 and again in Fig. 10 of the subject report. If a permeable connection between Martin and the other fields does exist, it is probably by way of a detour around this fault. The second point of difference between the two studies is illustrated by a comparison of Fig. 4 of the subject paper with Eg. A. Fig. A is obtained from an internal report on one of the studies made by this laboratory. It will be noted that the area indicated in Fig. 4 is roughly that marked "Pool Unit" in Fig. A. The additional portion of the aquifer shown in Fig. A was simulated on the reservoir analyzer by means of the water drive network. A satisfactory pressure match could not be obtained without this additional network. The differences involved here stem from a more fundamental consideration concerning reservoir analyzer operating techniques. The true source of these differences in reported results cannot at this time be determined because of the incompleteness of the subject paper. It is not stated, for instance, whether the pressure match was induced by altering the field resistance or the field capacitance, or both. Changing analyzer

Jan 1, 1953

By Helmar Schubert

The tensile strength of moist agglomerates consisting of granular materials is demonstrated with the aid of models. The applicability of these models is proved by experiments. An explanation of the different values of strength of imbibed and drained agglomerates is given and it is shown that the maximum tensile strength occurs at the so-called entry suction. The entry suction, which can be considered as the characteristic capillary pressure of the agglomerates, is described in terms of its parameters by a dimensional analysis. The influence of porosity is determined experimentally by means of regressional analysis and is compared with known model equations.

Jan 1, 1977

By W. A. Van Voast, J. J. McDermott, R. B. Hedges

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 12.50 mj/day of flow from storage and created a piezometric depression of 3 m or more as far as 1500 m from the mine. No wells have yet become nonproductive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures of ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand,

Jan 1, 1980

By G. A. Perry, C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). PED is a method by which predesigned pushbacks are sequenced into an optimized period-by- period design. The design that PED Produces is the design used in the field without further modifications. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system. It is in operational use.

Jan 1, 1984

By T. H. Alden

T. H. Alden (General Electric Research Laboratory)—This paper as well as earlier ones of Dr. Wood represent an important contribution to the experimental description of fatigue fracture. The mechanism of fracture proposed by the authors, however, is not established by this data nor supported by other data existing in the literature. Although taper section metallography provides a rather detailed picture of fatigue crack geometry, photographs so obtained must be interpreted with care. The narrow bands revealed by etching, frequently associated with surface notches, are labeled by the authors "fissures". Measurement shows, taking into account the 20 to 1 taper magnification, that the depth of these structures is at most 2 to 3 times the width. This distinction is important in the conception of a mechanism of crack formation. It is difficult, for example, to imagine a deep, narrow fissure arising from a "ratchet slip" model. A surface notch, on the other hand, may form easily by this mechanism. The notches observed in the present work are the subsurface evidence of the surface slip bands or striations in which fatigue cracks are known to originate.4-6 It is clear that an understanding of the structure of these slip bands is of key importance in understanding the mechanism of fracture. The evidence presented shows that these regions etch preferentially, possibly because they contain a high density of lattice defects, or as the authors state equivalently, because they are "abnormally distorted." However, it is not possible to conclude that the distortion consists of a high density of vacant lattice sites. The fact of a high total shear strain in itself does not assure a predominance of point defects as opposed to other defects, for example, dislocations. Other evidence in the literature which suggests unusual densities of point defects formed by fatigue7-' refers not to the striations or fissures, but to the material between fissures (the "matrix"). If a choice must be made, the preferential etching would seem to be evidence for a high dislocation density, since dislocations are known to encourage chemical attack in copper;g no such effect is known for the case of point defects. A third alternative is that the slip bands are actually cracked, but that near its tip the crack is too narrow to be detected by the authors' metal-lographic technique. In this case the rapid etching can be readily understood in terms of the increased chemical activity of surface atoms. Unless a vacancy mechanism is operative, the motion of dislocations to-and-fro on single slip planes will not lead to crack growth. Point defect or dislocation loop generation are the principal non-reversible effects predicted by this model. In any case, the nonuniform roughening of the surface in a slip band6 requires a flexibility of dislocation motion which is not a part of the to-and-fro fine slip idea. The same is probably true of crack growth by a shear mechanism. Either some dislocations must change their slip planes near the end of the band and return on different planes,'0 or dislocations of opposite sign annihilate." The mechanism by which these processes occur in copper at room temperature or below is that of cross slip. Thus cross slip appears to be essential to fatigue crack growth.6'10"12 The fact that a tensile stress opens the slip bands into broad cracks does not indicate the structure of the bands or the mechanism by which cracks form. The charactersitic concentration of slip into bands during fatigue shows a low resistance to shear strain in these regions. (This fact in itself may be inconsistent with a high concentration of vacancies.) The authors contend also that continuing shear produces an additional mechanical weakening so that the bands fracture easily (are pulled apart) under the influence of the superimposed tensile stress. It is equally possible that the only weakness is a weakness in shear, that the crack propagates by a shear mechanism, and that subsequently the tensile stress pulls the crack apart. Even the direct observation of bands opened by a tensile stress would not be conclusive since, as argued above, they may be fine cracks. The same argument applies to internal cracks, their existence in the presence of a tensile stress not indicating the mechanism of formation. Internal cracks originating in regions of heavy shear have also been seen following tensile deformation of OFHC copper,13 so that this mode of fracture is not unique to combined tensile and fatigue straining. The authors point out in their companion report14 that 90 pct of the cracks formed during pure tor-sional strain were within 8 deg of the normal to the specimen axis. If the tensile stress were an important factor in crack propagation, it is surprising that the cracks cluster about the plane in which the normal stress vanishes. Similarly, a study of zinc single crystals showed that for various orientations the life correlated well with the resolved shear stress on the basal plane,'= and was not dependent on the normal stress across this plane. W. A. Wood and H. M. Bendler (Authors' reply) -Dr. Alden's discussion emphasizes the essential point in the relation of slip band structure to

Jan 1, 1963

By Harold L. Hinds

The Homestake Ledge or Lead was discovered by Fred and Moses Manuel on April 9, 1876. They recovered a small amount of gold from the quartz outcrop, but, unfortunately, they were prospectors not hardrock miners. Their claim was sold to a group of experienced California mining men in 1877. These mining men incorporated their holdings as the Homestake Mining Company. This was the beginning of one of the greater gold mining enterprises of the Western World. Metallurgical operations progressed over the years from an eighty- stamp grinding circuit using amalgamation for recovery to the more complex circuit of today. The Homestake Mine, today, is an underground mine with the deepest winze reaching the 8,000-foot level. The ore is hoisted to the surface by two primary shafts, the Ross Shaft and the Yates Shaft. See Figures 1 and 2. It is crushed in three-stage crushing plants located in the headframes. From here, it is trammed to the mill fine- ore bins by electric locomotives. The Lead grinding plant milling circuit, known as the South Mill, receives ore from the crushing plant at minus 112 inch (Figure 3). This material is dumped into overhead fine-ore bins from five- ton rail cars. The fine-ore bins have a live capacity of about 3,700 tons. The South Mill bins can also be fed by a conveyor system which reclaims ore from an 80,000-ton capacity stockpile. This stockpile is built up from peak mining production periods and available surface low grade material. It is then reclaimed during low mine production periods. The grinding circuit at the South Mill consists of four rod mills in open circuit followed by four ball mills in closed circuit. Three of the rod mills are 6-foot by 12-foot Marcy's. The other is

Jan 1, 1983

By Max Heberlein, R. P. E. Hermsdorf

The electrolytic refining of metals for the removal of undesirable impurities has become a recognized necessity in the nonferrous field. Copper, lead, zinc, nickel, silver and gold have been produced in this manner for years. The United States Metals Refining Co., realizing that considerable quantities of lead and tin could be made available to the trade if a satisfactory method of purification of these metals could be established, decided to investigate the possibilities of electrolytic solder. In cooperation with Dr. Edward F. Kern, of the School of Mines at Columbia University, the company developed a process of electrolytic refining of lead-tin alloys using a tin-lead fluosilicate electrolyte. A pilot plant was installed in November 1927, and the commercial unit was put in October 1929. Since that time thousands of tons of electrolytic solder have been produced in this plant and consumed by all branches of industry that use solder. Older Methods of Producing Solder In the early days practically all solder was made by melting together virgin lead and tin in the proper proportions to meet specifications; then the solder was cast into the commercial shapes required. Today the base of most solders comes from scrap or secondary materials. Ordinarily solder is produced from secondary materials either by sweating solder-bearing scrap or by smelting lead and tin-bearing drosses, residues and similar materials. When solder is produced from scrap by sweating, clear solder is collected directly. It is then given some kind of kettle refining and usually blended to specification with virgin metals before it is cast into finished shapes. In producing solder from drosses and residues, the materials are usually first given a reducing smelting treatment from which a crude solder is obtained. This crude solder may be refined in several ways, but usually the first step is a furnace liquation to remove the bulk of the copper, which is followed by one of the more or less complicated methods for the removal of antimony and other impurities.

Jan 1, 1937

By Stuart McHugh, Douglas Keough

INTRODUCTION AND BACKGROUND Because of the potential for large reserves from increased production in the eastern Devonian shales, the Department of Energy (DOE), Morgantown Energy Technology Center (METC) selected these materials for the application and evaluation of existing and novel well stimulation techniques. One technique selected for further study was pulse tailoring, or tailored pulse loading, i.e., shaping the input borehole pressure history to produce a specific fracture pattern and to increase communication with the reservoir. The complexity and expense of in-situ mineback experiments prohibits direct evaluation of pulse tailoring in various geologic formations. An alternative approach used by SRI International consisted of evaluating fracture enhancement by computational simulations with supporting laboratory experiments and using data from field tests by other agencies to validate the computational model (McHugh and Keough, 1980). Laboratory experiments were conducted on core samples to determine fracture phenomenology and parameters and to verify material properties. The fracture parameters were obtained from posttest measurements of fracture distributions and correlation with stresses calculated by a wave propagation code. Model development was guided by these experiments and similar experiments in various materials performed by other agencies. The validity of the modeling, parameters, and scaling was evaluated by comparing fracture patterns from field tests with calculational simulations.

Jan 1, 1982

By D. W. Rudd, D. W. Vose, S. Johnson

The permeability of Mo-0.5 pel Ti to hydrogen was investigated over a limited range of temperature and pressuire (709° to 1100°C, 1.i and 2.0 atm). The resulting permeability, p, is found to obey the The experimental data justifies the permeation mechanism as a diffusion contl-olled pnssage of Ilvdrogen atoms through the metal barrier. 1 HE permeability of metals to hydrogen has been investigated by a number of workers and their published results have been tabulated by Barrer' up to 1951. Since most of the work on the permeability has been accomplished prior to this date, the compilation is fairly complete. Mathematical discussion of the permeability process has been reported by Barrer, smithells, and more recently by zener. From these efforts several facts are observed. First, the permeability of metals to diatomic gases involves the passage through the metal of individual atoms of the permeating gas. This is evidenced by the fact that the rate of permeation is directly proportional to the square root of the gas pressure. Second, the gas permeates the lattice of the metal and not along grain boundaries. It was shown by Smithells and Ransley that the rate of permeation through single-crystal iron was the same after the iron had been recrystallized into several smaller crystals. Third, it has been observed that the rate of permeation is inversely proportional to the thickness of the metal membrane. Johnson and Larose5 verified these phenomena by measurirlg the permeation of oxygen through silver foils of various thicknesses. Similar findings were noted by Lombard6 for the system H-Ni and by Lewkonja and Baukloh7 for H-Fe. Finally, it has been determined that for a gas to permeate a metal, activated adsorption of the gas on the metal must take place. Rare gases are not adsorbed by metals, and attempts to measure permeabilities of these gases have proved futile. ~~der' found negative results on the permeability of iron to argon. Also, Baukloh and Kayser found nickel impervious to helium, neon, argon, and krypton. From what was stated above concerning the dependence of the rate on the reciprocal thickness of the metal barrier, it is seen that although adsorption is a very important process, at least in determining whether permeation will or will not ensue, it is not the rate determining process for the common metals. A case in which adsorption is of sufficient inlportance to cause abnormal behavior has been noted in the case of Inconel-hydrogen and various stainless steels.'' APPARATUS The apparatus used in this study is shown in Fig. 1. The membrane is a thin disc (A), but is an integral part of an entire membrane assembly. The entire unit is one piece, being machined from a solid ingot of metal stock. When finished, the membrane assembly is about 5 in. long. Two membrane assemblies were made; the dimensions of the membranes are given in Table I. The wall thickness is large compared to the thickness of the membrane, being on the average in the ratio of 13 to 1. There exists in this design the possibility that some gas may diffuse around the corner section of the membrane where it joins the walls of the membrane assembly, If such an effect is present, it is of a small order of magnitude, as evidenced by the agreement of the values of permeability between the two membranes under the same temperature and pressure. A thermocouple well (B) is drilled to the vicinity of the membrane. The entire membrane assembly is then encased in an Inconel jacket and mounted in a resistance furnace. The interior of the jacket is connected to an auxiliary vacuum pump and is always kept evacuated so that the membrane assembly will suffer no oxidation at the temperatures at which measurements are taken. The advantages of this configuration are: 1) there are no welds about the membrane itself, so that the chance of welding material diffusing into the membrane at elevated temperatures is remote. 2) It is possible to maintain the membrane at a constant temperature. Since the resulting permeation rate is very dependent upon temperature, it is advisable to be as free as possible from all temperature gradients. 3) It is possible to obtain reproducible results using different specimens. The only disadvantage to this configuration is the welds (at C) in the hot zone. The welding of molybdenum to the degree of per-

Jan 1, 1962

By E. Gybbon Spilsbury

Everybody who has had his attention turned to the gold-deposits of the Southern States, is acquainted with the undisputed fact of the existence, at least in the Carolinas and Georgia, of enormous areas of gold-bearing rocks. Long before the discovery of the precious metal in California, gold-mining on a very extensive scale mas a well-estab-

Jan 1, 1887