Search Documents

By W. G. Pfann

THE problem of forming points on wires that were from 0.002 in. to 0.010 in. in diam arose in the recent appearance of silicon and germanium point contact rectifiers as elements in microwave radar.1 In these devices a pointed tungsten wire makes a delicate contact with the surface of a semiconductor. Because the quality of such rectifiers is largely determined by the nature of this contact, considerable attention has been given to the formation of the metal point. Reproducibility of contour and freedom from burrs and even microscopic irregularities are considered essential. The operations involved must be simple and rapid enough for mass production. Previously tungsten wires had been provided with conical points by a grinding method which involved rotating a wire about its axis and causing it to bear at an oblique angle against a spinning abrasive disc. This was later complemented with an electrolytic polishing treatment which removed irregularities from the ground point and also rounded it off at the tip-a desirable feature. Finally, these operations were supplanted by the electrolytic pointing method described here. MECHANISM OF POINT FORMATION The wires to be pointed are partially immersed- in an electrolyte in a .vertical position whereupon they are provided with smooth rounded points entirely by electrochemical action. The process is independent of the depths to which the wires penetrate the electrolyte because the points are formed at the surface level. It may be used to point a single wire or many of them simultaneously and is applicable to wires of different diameters within a limited range. Solution of the immersed portion of a tungsten wire is accomplished by making it the positive electrode in an electrolytic cell, as shown in Fig I. While the wire is maintained at constant voltage the current through the cell falls continuously, principally because of the decrease in wetted area which results from solution of the tungsten. This increase in resistance occurs in a reproducible manner and is used as a control in the process. As the immersed portion of the wire dissolves, it remains cylindrical in shape except for the short section which is wetted by the meniscus. Here the rate of solution is lower and decreases as the top of the meniscus is approached. The result is the formation of a tapered section inside the meniscus. As solution continues, the cylindrical section either dissolves entirely or drops off just before complete solution, leaving only the taper which is now sharply pointed. Further action causes this point to become rounded and then quite blunt, until finally the end of the wire is almost plane. Fig 2 shows the stages in this development. Contour PF is most representative of those used in point contact rectifiers. Thus a variety of point

Jan 1, 1947

By C. L. Meyers, A. V. Levy, G. Y. Onoda, R. J. Kotfila

This paper presents the hypothesis that solid-solution hardening of regions in the order of tens of angstroms thick along grain boundaries is the most important mechanism controlling the ductile -brittle transition behavior of poly crystalline bcc refractory metals. Further, a physical model is developed and a general equation is derived to describe the dependence of the solute concentration at grain boundaries on temperature, nominal impurity concentration, thermal treatments, vain size, and prior plastic deformation. Analytical curves of the solute concentration at grain boundaries us temperature, calculated by means of the derived equation, are found to have the same general form as curves of ductility us temperature plotted from experimental data. Senziquantitative relationships between the transition temperature and metallurgical variables can he determined by using the physical model. The room-temperature brittleness of the poly-crystalline refractory metals (tungsten, molybdenum, and chromium) is a result of their high ductile-brittle transition temperatures. Recently studies on single crystals have revealed that, when sufficiently pure, these crystals have much lower transition temperatures than polycrystalline specimens of similar purity.'-3 For example, the transition temperature (measured by reduction in area in tensile tests) for very high-purity tungsten crystals has been reported to be as low as -50°F whereas polycrystalline specimens of similar purity had a transition temperature near 400" ~.' These results suggest that the ductile-brittle transition behavior of these polycrystalline metals can be attributed principally to the influence of grain boundaries on plastic flow and fracture. This paper contains a discussion of the manner in which grain boundaries influence the ductility of the poly-.crystalline bcc refractory metals and proposes that the segregation of impurities to grain boundaries is the most important mechanism for controlling the ductile-brittle transition behavior of these metals. Further, this paper contains an analysis of the effect of the compositional and structural variables on the grain boundary-ductility relationship, and introduces a semiquantitative model that can provide a foundation for more theoretical treatment to describe the influence of these variables on ductile-brittle transition behavior. PHYSICAL MODEL FOR PREDICTING DUCTILE-BRITTLE TRANSITION BEHAVIOR Grain Boundary Segregation of Impurities. Based on their own observations and on theoretical grounds, numerous investigators have suggested that impurities segregate to the grain boundaries. Such segregation would be expected because regions exist where both large and small foreign atoms fit with less strain than within the undistorted crystal structure. Therefore, the concentration of impurities should be higher at boundaries than within the grain body. TO estimate the degree (i.e., the ratio of grain boundary to nominal bulk concentration) to which an interstitial solute tends to segregate at boundaries within a solvent metal, the solubility rather than the size misfit could be used as a guide because solubility expresses the joint effect of both elastic and electronic factors.5 The solubilities of interstitial elements such as carbon, hydrogen, nitrogen, and oxygen are low in the group V-A metals and very low in the group VI-A metals.6 These low solubilities suggest that segregation to grain boundaries should occur for each of these solutes in both refractory metal groups. The difference between the ductility of single-crystal and polycrystalline bcc refractory metals can be described in terms of two distinct effects.4 The first of these is the general observation that grain boundaries hinder slip within grains and slip transfer between grains, and the second is that deformation is more complex in each grain of a polycrystalline specimen than it is in a single crystal. Mc Lean has pointed out, furthermore, that strong slip-hindrance effects at grain boundaries should occur in metals having strong segregation of impurities to grain boundaries. Therefore, the effect of grain boundaries on the hindrance of slip is expected to be the dominating influence on the ductile-brittle transition behavior of these polycrystalline refractory metals. cahn5 has suggested that temperature and solute mobility should influence solute equilibrium segregation at grain boundaries, and Fig. 1 illustrates

Jan 1, 1965

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By Robert Linton

THE PURCHASE of silver by the United States Government under the provisions of the Pittman Act is practically completed. Producers of silver in this country will now have to market their silver in competition with the rest of the world. It therefore becomes of interest to study such data as are available and endeavor to obtain such suggestions as may be afforded therefrom as to the probable future market position of the metal. Conditions influencing the marketing of silver are numerous and complex. It is a commodity entering. into the arts and manufactures, and therefore influenced by the condition of various lines of business which make use of it; it is currency-being used by all countries for subsidiary coins and even as the founda-tion of the system by a very few; and it serves as a frequent basis for speculation. The various factors involved can easily set up so many cross-currents in the flow of the metal that predictions in regard to the market position of silver can never be safely made, although it may be possible to form some idea of prob-able trends over a sufficiently long period. Of course price is determined, as is the case with all commodities, by the inexorable workings of the law of supply and demand.

Jan 6, 1923

By B. D. Thomas

GRAVITY concentration is a general term designating processes for separating and sorting granular material by means of forces that depend on the density, size and shape of the particles. When these forces are applied to the particles the latter are caused to move, those of a given density along one path and those of a different density along another, until ultimately they are sufficiently separated to be removed from the operation of the process. The forces producing this separation are in general complex and, unfortunately, no completely rigorous analysis of them has as yet been devised. The science of the hydrodynamics of viscous fluids deals with the little that is known about the problem. Every observer of nature is familiar with the fact that an object moving in a fluid encounters a force of resistance. We have only to walk against a brisk wind or stir a cup of coffee, or observe the slow fall of a grain of sand in water, to experience directly the fact that such forces exist. The exchange of force between an object and a fluid in which it is moving operates on the fluid as well as on the object. Thus a sailboat may be set in motion by the force exerted by the wind on the sail; but the sail also deflects the wind-furthermore, the water in which the boat floats is set in motion by the force exerted by the boat as it cleaves through the water. The wind is thus enabled to do work on the water through the intermediary of the boat. In general, an object moving through a fluid encounters a force that opposes the motion and also acts to change the motion of the fluid. In gravity concentration we are dealing with this force of resistance acting on the granular particles that are to be separated. Furthermore, the motion induced in the fluid by a particle will in turn affect the motion

Jan 1, 1943

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By K. E. Beu

THE integrated intensity X-ray method of meas-uring retained austenite concentrations in hardened plain carbon or low alloy steels as proposed by Averbach and Cohen1,2 has the advantages of being a highly sensitive and precise quantitative method. The various phases of this method have been studied and several modifications have been developed which aid not only in reducing the time required per determination, but which also increase the possible accuracy of the method. A fundamental step in the original calculation procedure is to plot V.A(?) curves for austenite and martensite and to obtain VM/VA ratios from these curves.' In taking this ratio the absorption factor A (8) drops out since it is constant for a. given diffraction angle 8. The reason for eliminating A(?) in this manner is because it is apparently assumed

Jan 1, 1953

By C. A. Fothergill

An improved blotter model is described which makes use of a plastic sheet as base for the blotter field and pins to represent the input wells. The model is simple to construct and adapt and is particularly useful for demonstration purposes. Operational details are given. INTRODUCTION The blotter model was first applied to the investigation of oilfield problems by Wyckoff, Botset and Mus-kat,' primarily in order to demonstrate the flood patterns which could be expected from various arrangements of input and output wells in waterflooding projects. In recent years the model has been largely superseded for analog studies by the potentiometric and electric analog models which are more refined and versatile, since they can simulate the form, and, in certain cases, permeability variations which it is not possible to do with the blotter model. However, the latter is still used for analog studies where the reservoir can be represented as being uniform in thickness and permeability, and where a visual record of the flood advance is required. Ramey andNabor,2 for example, have applied the model to the investigation of areal sweeps in oil recovery by in-situ combustion. Because of its limitations, the blotter model can be used in general for only very simple arrangements of input and output wells, but within these limitations it has a definite advantage over all other types, in that it provides a picture of the advancing flood using the simplest and most easily constructed apparatus, by contrast with the gelatin model, for example, which requires more elaborate equipment. Moreover, the experiments can be quickly repeated and modified if necessary, whereas considerable time is required to prepare a gel field, compared with that required for the preparation of sheets of conducting blotting paper. For these reasons the blotter model can be very useful for demonstration and teaching purposes, enabling the student to experiment for himself with different arrangements of input and output wells. A model has been constructed for this purpose which is simple to operate and adapt. The model (Fig. 1) consists of a base platform or box, approximately 12-in. square, on top of which are screwed three lathes of 1/2 -in. square section to form three sides of a square 6 in. in length. This forms the support for a sheet of Cobex, transparent plastic, thickness .003 in., on which is carried the blotting paper representing the field. The plastic is flexible and relatively soft, and can be attached to the support by cellulose tape so that it can be easily removed when required. The input wells are represented by brass drawing pins pressed through the plastic sheet from the underside until the points are just projecting through the top; these are connected in the circuit as shown in Fig. 2. The sheet of blotting paper of required shape and size is saturated with a solution of 0.2 n-potassium sulfate to which has been added a saturated alcohol solution of phenol-phthalein at a strength of 10 cc/liter of stock solution. The surplus water is removed and the blotting paper placed in position on the plastic sheet making contact with the drawing pins and the sheet (which is an insulator). The anode consists of a second sheet of blotting paper cut as shown and saturated with the same solution. This is suspended from a laboratory stand, being connected to the conducting wire by means of a crocodile clip and making contact with the horizontal blotting paper at the projecting point. This is the method used by Ramey and Nabor and which permits the hydroxyl ions or colored front to reach the anode. As shown in Fig. 2, the electrical voltage used is 220-v DC and a shunt is placed across the terminals to step down the voltage as required. Further adjustment can be made as necessary using a lamp board in series with the shunt to obtain the

Jan 1, 1958

By A. Taylor

IN a previous communication,l the quaternary system Ni-Cr-Ti-A1 was described in detail and it was shown how certain alloys used for high-temperature applications could be construed as consisting of Ni,Cr suitably modified by the addition of aluminum and titanium in relatively small amounts. With the correct aging treatment, the ordered face-centered-cubic Berthollide phase, y'-Ni,Al, could be precipitated from the face-centered-cubic primary y-solid solution. By increasing the proportion of titanium with respect to aluminum, it was also possible to precipitate the very brittle hexagonal-close-packed Daltonide phase, ?-Ni,Ti. From the nature of the system it seems reasonable to expect the y and y'-phases to take appreciable amounts of cobalt and iron into solid solution. In the case of the present investigation it was decided to confine the work to iron additions only. This element may be introduced in two quite distinct ways: 1) as a simple replacement for nickel; and 2) as a replacement for chromium, titanium, and aluminum. The second method of iron addition forms the basis of the present investigation, which is, in effect, a study of the pseudo-quaternary system Ni,Cr-NiPe-Ni,Ti-NLAl. For purposes of reference, Figs. 1, 2, and 3 have been included and illustrate the quaternary system Ni-Cr-Ti-A1 described in the previous paper along with sections through N&Cr-Ni,Ti-Ni,Al at 750" and 1000 "C respectively. As will be shown below, the pseudo-quaternary system with components Ni,Cr, NiPe, Ni,Ti, Nihl is remarkably similar in many ways to the face defined by Ni,Cr-Ni,Ti-Ni,Al because of iron re-

Jan 1, 1958

By Minoru Sasabe, Mayurni Sorneno, Kazuhiro Goto

I) The Object of the Present Experiment. When the oxygen chemical potential in the gas phase is changed, the oxygen chemical potential in the liquid metal or in the liquid oxide phase will be subsequently changed. The object of the present experiment is to develop a method of measuring the change in the chemical potential of oxygen in liquid metals and in liquid oxides with respect to time, when the oxygen potential in the gas phase changes. II) The Experimental Method. The following types of the oxygen concentration cells with the solid electrolyte of Zr0z-CaO are used: KAZUHIRO GOTO, MemberAIME.MINORU SASABE,and MAYUMl SOMENO are Associate Professor, Research Associate, and Professor, respectively, Department of Metallurgical Engineering, Tokyo Institute of Technology, Meguro-ku, Tokyo, Japan. Manuscript submitted March 12, 1968, EMD. Igas phase liquid Ag or Pb ZrO2-CaO electrolyte!, The measured reversible electromotive force can be expressed by the next equation, provided that the transference number of the oxygen anion in the electrolyte is unity: E = RT/nF log (at electrode I)/P~ (at electrode 11) where is the electromotive force, R is the gas constant, T is absolute temperature, n is valence of oxygen anion, and Pq is the oxygen pressure at the electrodes. As shown in the previous work1 of the authors, the electromotive force is determined by the difference in the chemical potential of oxygen at the vicinity of the interfaces between the solid electrolyte and the electronic conductors used for the two electrodes. Fig. 1 shows the two kinds of the cell assembly used to measure the change of the chemical potential of oxygen in liquid metals and liquid oxides with respect to time. In both cases, the change of the oxygen pressure in the gas phase is measured by the independent oxygen concentration cell located above the

Jan 1, 1969

By A. Simkovich, C. W. McCoy

THE relationship among chromium, carbon, and temperature during the oxidation period of stainless steel melting was developed by Hilty et a1 1-3 whose studies were confined to plain chromium stainless steels. The simplified version of their relation is given by the equation:

Jan 1, 1962

By S. B. Patterson, A.R. Amos

Log washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate completely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5" to 10" and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1938

By A. R. Amos, S. B. Patterson

Log washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate completely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5" to 10" and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1938

By J. W. Rutter, K. T. Aust

The temperature dependence of the rate of grain boundary migration was measured in bicrystals of zone-refined lead containing from 20 to less than 1 ppm by wezght of tin. The apparent activation energy in the temperature range from 320" to 200oC is markedly dependent upon the solute tin concentration and upon the orientation relationship of the grains adjacent to the grain boundavy. The quantitative experimental observat~ons are compared with the predictions of various theories of grain boundary migration. In previous work.&apos;?&apos; the mobility of individual grain boundaries was studied as a function of impurity concentration and type of boundary. Grain boundary migration occurred at the expense of dislocation arrays which were introduced into the specimen during solidification. Boundary mobility in zone-refined lead at 300°C was markedly decreased by small additions of tin. 0.004 wt pct being sufficient to decrease the rate of grain boundary migration by a factor of 1000. The mobility of grain boundaries having polar orientation relationships near 38 and 22 deg about <Ill>, and 28 deg about <100>, was much less sensitive to tin concentration in the range studied. As a result, these boundaries have relatively high mobilities. The present paper is a continuation of the above study. Data are now presented on the temperature dependence of the motion of individual grain boundaries in zone-refined lead as a function of solute tin concentration and orientation relationship of adjacent grains at the grain boundary. The experimental observations are compared with the predictions of a number of theories of grain boundary migration3-8 which, prior to the present experimental investigation, could not be critically evaluated. EXPERIMENTAL PROCEDURE The striation or lineage structure of melt-grown single crystals of zone-refined lead, containing various additions of tin, was utilized to provide a driving force for grain boundary migration, as previously described.1,2 Each grain boundary under study separated the striated single crystal from another grain which was introduced by localized plastic deformation and recrystallization of a small region of the sample. The speed of migration of grain boundaries in dilute alloys of tin in zone-refined lead was investigated as a function of 1) tin concentration from < 0.0001 to 0.002 wt pct, 2) temperature in the range of 200" to 320°C, and 3) orientation relationship of the adjacent grains at the grain boundary. The substructure driving energy available for grain boundary migration was estimated to be about 4000 ergs per cu cm, within a factor of two, from specimen to specimen.&apos; The specimen dimensions, and growth and alloying procedures for the preparation of striated single crystals of lead of known tin composition, were as described previously.&apos; Each bicrystal was carefully wrapped in aluminum foil, and annealed in a well-stirred salt bath consisting of 50 pct NaNO2 and 50 pct KNO3, for known periods of time at a series of constant temperatures (*2°C). The grain boundary positions, before and after each anneal, were determined by etching lightly in a solution of 5 pct nitric acid in methyl alcohol, in order to follow the motion of the boundary and determine its rate of migration. Thus, the rate of motion of the grain boundary in a single specimen was measured at various temperatures. The above procedure was carried out for each grain boundary in seventeen different bicrystal specimens.

Jan 1, 1960

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5&apos;798&apos;14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970

By W. F. Laverty

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs&apos; absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

DEPENDENCY on foreign sources for many mineral raw materials is a characteristic of our economy which is becoming painfully evident. Although investment in foreign mining projects has increased, it has not kept up with the growing demand for foreign minerals. The sphere of American investment capital in mining ventures abroad has been severely limited by the rise of nationalism in many underdeveloped countries. Consequently, we can look back over half a century in which mining investment, exclusive of petroleum, has increased by 50 pct whereas other American investments abroad have multiplied by better than 300 pct. Investment in foreign mining or petroleum encounters different problems than capital investment for other industries. It is rarely invested in industrialized nations. Most of it goes to countries with expanding frontiers, like Canada, or to underdeveloped nations like Liberia. It must be used for building communities, recruiting and training labor, and establishing lines of communication and transportation. These complications are an accepted part of the mining game. However, the most complex problem is in those countries which consider mineral exploitation a usurpation of the people&apos;s natural heritage. This is a characteristic of the young government existing by a tenuous balance of power in an underdeveloped nation. American mining capital understandably has shunned these nations as being poor investment risks. However, they possess minerals which are needed by industry. Our government has attempted to stimulate mineral supplies beyond those provided from abroad by private capital. ECA, now under DMPA, makes loans to foreign mining companies. Since the ECA program cannot be expected to continue indefinitely, Point IV seems to be the logical next step to encourage foreign countries to fill our shortages. However, only 1 pct of the $35 million budget provided in the first year for Point IV was alloted for mining programs. Considering the need for minerals and the difficulties of procuring them by private investment, a larger share is needed and justifiable. Those who have been engaged in foreign mining can vouch for the fact that it takes many decades to teach the complex technology and economics of mining to the natives of under-developed countries. For this reason Point IV must be considered a long range program. Mineral requirements for the present must be met by more direct measures. Encouragement of private investment in foreign mining by such incentives as tax relief on profits from foreign sources, international bank-borrowing facilities for private capital, and diplomatic assistance in encouraging foreign countries to cooperate are imperative for our future mineral security.

Jan 1, 1952

By H. F. Moore

We have studied the simple case of repeated stress, without considering impact, which might bring in other factors. This investigation has shown that steel under repeated applications of stress, reversed from positive to negative, will not fail below some fairly clearly defined limiting stress that, so far we can see, does not bear any definite relation to the ordinary elastic limit, being as large as the elastic limit in some cases and about one-half the elastic limit in others. According to one theory, fatigue is the result of changes in crystalline structure by repeated stress. I do not know of any evidence in favor of this theory. The crystals are broken under repeated stress. According to Bauschinger, under repeated stress some inherent property of the material changes its elastic limit; possibly some property of the amorphous cement between the crystals. A third theory is that all fatigue of metals is the result of the spread of damage from little localized overstresses. While I do not feel justified in accepting the last theory rather than the second, I have yet to run across a case of failure of steel or other metal, either in the laboratory or in service, that could not be explained by the gradual spread of damage from some nucleus. We have found, for example, that it is possible to subject a homogeneous steel, like Armco iron or a 0.90 per cent. carbon steel, that has been thoroughly annealed, to one hundred million reversals of stress as high as the elastic limit of the steel with no sign of failure. On the other hand, a complex structured steel, like a chrome-nickel steel that has been hardened with very little drawing, will fail at a stress about 58 per cent. of its elastic limit. Between these two we get a variety of results. In the steel work of any building, there are undoubtedly many thousands of places where structural damage was done—where riveted members were bent into place cold and where the rivets were fitted with drift pins, etc. Locally the steel in the building was stressed beyond its yield point in many places. These little localized overstresses do no damage at all; the building is entirely safe. But if this building were subjected eight or ten times a day to a mild earthquake, these little localized overstresses might be nuclei from which damage would spread

Jan 1, 1922