Search Documents

By H. W. Page

Petroleum requirements since V-J day have been appreciably higher than predicted. Foreign operations now exceed maximum wartime levels by about 14 per cent. Domestic operations since V-J day have averaged 92 Per cent of the wartime peak. In spite of maximum foreign refinery runs, large exports of all products, except residual fuel oil, are necessary to meet foreign demand. During the next few years it is expected that foreign operations will continue at capacity, including new installations, but that, because of increases in foreign demand, exports will continue at about their present level. Domestic operations will increase during this period and crude production probably will exceed maximum efficient rates. Even after 10 years some exports probably will be required, but eventually these will be supplanted by increased output of foreign refineries, except for small tributary exports. The increase in domestic requirements will exceed the decline in exports. Unless findings of crude oil exceed present expectations, the increasing demand will be met by increased imports and synthetic methods-—such as the Hydrocarbon Synthesis Process for conversion of natural gas and coal to gasoline and distillates. Catalytic cracking installations will increase as crude availability decreases. This will help to meet the increasing demand for gasoline but will intensify the domestic shortage of residual fuel oil. Eventually larger imports will be required to satisfy the demand for this product. Introduction Under the pressure of the wartime period, there was time only occasionaly to look ahead in anticipation of what the postwar era held for the petroleum industry. Perhaps the general expectation was that a rather pronounced decline in the level of industry petroleum operations would take place shortly after the end of the war, with the impact felt mainly on the economy of the United States- It is of interest now, nine months after V-J day, to take inventory of the near-term situation and see what significant forces are at work. With this as a starting point, it should be possible to engage in something more satisfactory than pure speculation concerning trends in the immediate future and 10 to 20 years ahead. Present and Near-term Situation During the nine-month period following V-J day, foreign crude oil production and rebery operations have actually increased the These activities were at maximum capacity on V-J day but the continuation of drilling programs, the completion of new and rehabilitated refineries and of transportation facilities during the Past nine months have increased the foreign capacity. This added capacity has been fully utilized. Foreign crude oil production in May 1946 is about 14 per cent higher than during July 1945 and refining operations some 12 per cent higher' During the same period there has been a falling off in similar activities within the

Jan 1, 1947

By H. W. Page

Petroleum requirements since V-J day have been appreciably higher than predicted. Foreign operations now exceed maximum wartime levels by about 14 per cent. Domestic operations since V-J day have averaged 92 Per cent of the wartime peak. In spite of maximum foreign refinery runs, large exports of all products, except residual fuel oil, are necessary to meet foreign demand. During the next few years it is expected that foreign operations will continue at capacity, including new installations, but that, because of increases in foreign demand, exports will continue at about their present level. Domestic operations will increase during this period and crude production probably will exceed maximum efficient rates. Even after 10 years some exports probably will be required, but eventually these will be supplanted by increased output of foreign refineries, except for small tributary exports. The increase in domestic requirements will exceed the decline in exports. Unless findings of crude oil exceed present expectations, the increasing demand will be met by increased imports and synthetic methods-—such as the Hydrocarbon Synthesis Process for conversion of natural gas and coal to gasoline and distillates. Catalytic cracking installations will increase as crude availability decreases. This will help to meet the increasing demand for gasoline but will intensify the domestic shortage of residual fuel oil. Eventually larger imports will be required to satisfy the demand for this product. Introduction Under the pressure of the wartime period, there was time only occasionaly to look ahead in anticipation of what the postwar era held for the petroleum industry. Perhaps the general expectation was that a rather pronounced decline in the level of industry petroleum operations would take place shortly after the end of the war, with the impact felt mainly on the economy of the United States- It is of interest now, nine months after V-J day, to take inventory of the near-term situation and see what significant forces are at work. With this as a starting point, it should be possible to engage in something more satisfactory than pure speculation concerning trends in the immediate future and 10 to 20 years ahead. Present and Near-term Situation During the nine-month period following V-J day, foreign crude oil production and rebery operations have actually increased the These activities were at maximum capacity on V-J day but the continuation of drilling programs, the completion of new and rehabilitated refineries and of transportation facilities during the Past nine months have increased the foreign capacity. This added capacity has been fully utilized. Foreign crude oil production in May 1946 is about 14 per cent higher than during July 1945 and refining operations some 12 per cent higher' During the same period there has been a falling off in similar activities within the

Jan 1, 1947

By Persifor Frazer

IN his “Final Report," Vol. II, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

Jan 1, 1877

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,' however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500' with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962

IT is necessary that all men who wish to bring things to a certain end should think of the agents needed to attain this. Now whichever one of the above processes you wish to use you must consider the nature of the material and see whether it is disposed to render what you wish to extract. Then you must see whether you have the other agents sufficiently powerful and proportioned to attain this result, for if the things were not in harmony your work would be vain and very laborious. Therefore, if you should wish to make waters or oils by way of distilla-

Jan 1, 1942

By A. M. Hall

Sulphur, even in small amounts, may often be harmful to nickel and high-nickel alloys, causing impairment of mechanical strength and destruction of malleability and ductility, as shown by Merica and Waltenberg.l,2 It may act either in the form of nonmetallic inclusions produced in the liquid state during furnacing or as reaction products resulting from its diffusion into the solid metal. In recognizing the action of this element, ability to identify its various forms by means of the microscope is often of considerable importance, especially when direct quantitative methods are inapplicable. Of the sulphur compounds associated with nickel and high-nickel alloys, the sulphides that may be found in malleable nickel, Monelt and Inconel are an important group. These sulphides were investi- gated by metallographic methods in order to provide descriptive data by which to identify them. The nominal compositions of malleable nickel, Monel and Inconel are given in Table I. The term "sulphide" is employed here in a very general sense, to designate a substance in which sulphur and one or more metallic elements are combined. The term includes any combinations of compounds and solid solutions. Method of Investigation Three groups of small laboratory melts were made, one group to represent each of the three types of alloy under investigation. Within each group, a number of ingots with a sufficient variety of chemical analyses were prepared so that the effect of each of the elements entering the complete commercial alloy could be isolated and observed. In most cases, to facilitate metallographic study by exaggerating the number and size of the resulting sulphides, somewhat greater amounts of the minor elements were added than are present in the commercial alloys. Likewise, considerably more sulphur was added than is normal, but not enough to complicate the system. Transverse sections were cut at a point one third of the distance from the butt to the head of each ingot, polished and examined with an inverted stage metallo-graph equipped with a combination polar -izing-analyzing vertical illuminator. The light source was a tungsten-mercury vapor arc lamp.

Jan 1, 1943

By A. M. Hall

Sulphur, even in small amounts, may often be harmful to nickel and high-nickel alloys, causing impairment of mechanical strength and destruction of malleability and ductility, as shown by Merica and Waltenberg.l,2 It may act either in the form of nonmetallic inclusions produced in the liquid state during furnacing or as reaction products resulting from its diffusion into the solid metal. In recognizing the action of this element, ability to identify its various forms by means of the microscope is often of considerable importance, especially when direct quantitative methods are inapplicable. Of the sulphur compounds associated with nickel and high-nickel alloys, the sulphides that may be found in malleable nickel, Monelt and Inconel are an important group. These sulphides were investi- gated by metallographic methods in order to provide descriptive data by which to identify them. The nominal compositions of malleable nickel, Monel and Inconel are given in Table I. The term "sulphide" is employed here in a very general sense, to designate a substance in which sulphur and one or more metallic elements are combined. The term includes any combinations of compounds and solid solutions. Method of Investigation Three groups of small laboratory melts were made, one group to represent each of the three types of alloy under investigation. Within each group, a number of ingots with a sufficient variety of chemical analyses were prepared so that the effect of each of the elements entering the complete commercial alloy could be isolated and observed. In most cases, to facilitate metallographic study by exaggerating the number and size of the resulting sulphides, somewhat greater amounts of the minor elements were added than are present in the commercial alloys. Likewise, considerably more sulphur was added than is normal, but not enough to complicate the system. Transverse sections were cut at a point one third of the distance from the butt to the head of each ingot, polished and examined with an inverted stage metallo-graph equipped with a combination polar -izing-analyzing vertical illuminator. The light source was a tungsten-mercury vapor arc lamp.

Jan 1, 1943

By F. M. Lewis, J.F. Myers

The Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accomplished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1943

By J. F. Myers, F. M. Lewis

The Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accomplished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1943

By Gerhard Derge, Harold Markus

The first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from 1.12† volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. Experimental Data Cations.—The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.1 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 10-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By Harold Markus, Gerhard Derge

The first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from 1.12† volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. Experimental Data Cations.—The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.1 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 10-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By Sage B. H., Lacey W. N., G. W. Billman

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By Sage B. H., G. W. Billman, Lacey W. N.

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By G. Carman Ridland

IN conjunction with a geological investigation of the silver-bearing veins at Contact Lake, Northwest Territories, Canada, a survey was made with a Geiger-Müller counter of the gamma-ray emissions from the rocks in the vicinity of the mine workings. Discontinuous pitchblende veins have been encountered occasionally in the silver-bearing fissures, and the geophysical survey was undertaken with the hope that abnormally high gamma-ray intensities, if detected, might lead to larger and more continuous pitchblende discoveries. Before the instrument was used at. Contact Lake, preliminary tests were made, first with laboratory specimens at Princeton University, and later over known pitchblende deposits at the Eldorado property, LaBine Point, N.W.T. The Geiger-Müller counter, as adapted for field use, is described; the technique of transporting and operating the instrument is outlined; and the general precautions to be observed are discussed. The results obtained at Great Bear Lake show that the instrument is capable of detecting not only a pitchblende ore shoot in a shear zone, but also the mildly radioactive "host rock" at a considerable distance from the ore body. Hence, use of the Geiger-Müller counter is urged, not just for the detailed search for an ore body in a shear zone, but for the detection of possible radioactive "host rocks" in large-scale reconnaissance surveys of unexplored regions made by prospectors and members of federal geological survey parties.

Jan 1, 1944

By J. T. Norton, N. J. Grant, A. R. Chaudhuri

MOST of the recent work to establish the mech-anism of creep in metals at high temperatures has utilized aluminum as the experimental material. It was thought desirable to initiate an investigation of a hexagonal close-packed metal, because of the relatively simple slip system, and compare the observed deformation characteristics with those that have been observed for the face-centerd cubic metals. High-purity magnesium was chosen for this purpose, first, because its strength and other mechanical properties are similar to those of aluminum in the same temperature range, and second, because the existing equipment was ideally suited to observe magnesium during creep. It is proposed in this paper to present a pictorial and qualitative account of the changes that high-purity magnesium undergoes during creep at 500°F. The characteristics of deformation of aluminum described below have been observed by various workers and accounts of these may be obtained from the papers of Chang and Grant.'- These characteristics are: slip, subgrain formation, grain boundary sliding and migration, fold formation, deformation bands, and kink bands. It is well known that in a flat magnesium specimen, slip on the basal plane (0001) in the [1120] direction results in the formation of straight bands on the surface of the specimen. Schmid and co-workers' have shown that this system is operative in the temperature range of -185" to 300°C (-300° to 572°F). They have also shown that a second system, slip on the pyramidal planes {1071} or {1012} in the [1120] direction, is operative at temperatures higher than 225°C (437°F). Between 225° and 300°C (437" to 572°F), therefore, deformation by both these systems is expected. Bakarian and Mathewson5 confirmed the occurrence of pyramidal slip on the {1011} plane and found that it resulted in irregular markings on the surfaces of their specimens. Burke and Hibbard6 obtained evidence of pyramidal slip in single crystals of magnesium deformed at room temperature. Bakarian and Mathewson5 suggested that the irregular appearance of these bands was due to slip on both of the pyramidal planes occurring simultaneously but in the same direction, the close angular relationship between the planes making this process possible. Furthermore, since neither of these planes is close enough to the basal plane, slip on the latter does not exhibit the irregular appearance of slip bands resulting from pyramidal slip. Experimental Procedure High-purity magnesium, supplied by the Dow Chemical Co., was used in these experiments. The analysis was as follows: Al, 0.0002 pct; Mn, 0.0018; Fe, 0.0024; Cu, 0.0002; Sn, 0.001; Ca, 0.01; Ni, 0.0003; Zn, 0.01; Pb, 0.0005; Si, 0.001; and Mg, 99.972. The magnesium was supplied in the form of 1/2 in. diam rods. The specimens had an overall length of 21/4 in., the round ends being threaded to fit the specimen holders. The previously round 3/16 in. diam gage section of the specimen had two parallel flats machined on opposite sides for microscopic observation, yielding a test zone having the dimensions of lx3/16x7/64 in. The specimens were electrolytically polished (without prior mechanical polishing of the machined flats), in a solution composed of 375 ml of ortho-phosphoric acid and 625 ml of ethyl alcohol.' The cathode was a stainless steel sheet bent so that the specimen was completely surrounded. The voltage for successful polishing was 1.5 v at 100 to 300 milli-amp current. Electropolishing for about 45 min sufficed to obtain a good metallographic surface on the specimens after they had been machined. The creep tests were performed under constant load, and two types of equipment were used. In the first, designed by Servi and Grant,V he specimens were beam-loaded, and a furnace could be lowered to surround the specimen. As the microstructural changes could not be observed during the course of the test, the tests had to be interrupted periodically by removing the specimen for microscopic examination. The second unit was a high temperature microscopy furnace designed by Chang and Grant.' The furnace was fitted with an optically flat quartz window having area dimensions 1.25x0.5 in., so that the whole test portion could be viewed through it at magnifications up to x240. The metallurgical microscope had three mutually perpendicular axes of motion, and, in addition, it was possible to measure angular displacements by rotation of the eyepiece. It was thus possible to make precise observations of the specimen during creep, and micrographs could be taken by attaching a camera to the eyepiece of the microscope. The average grain size of the specimens that were tested was about 1 to 3 mm. This grain size could

Jan 1, 1954

By J. B. Newkirk, A. H. Geisler

Certain of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some perrnanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems oA&apos;er for study over the usual in which an intermetallic compound is formed are many: 1. Since the precipitate has the same crystal strutture as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be ex. petted to have the same orientation. 3, Small &,registry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from 0 to 100 pet* thus permitting wide freedom for the study of the effect of cornposition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1&apos;2 The two have the same <Jo parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for CU-Ni-CO alloys because of the similarity in constitution but this had not been demonstrated. The Present investigation was conducted on a CU-Ni-CO alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established, however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system Was chosen for a comprehensive investiga-

Jan 1, 1949

By C. A. Stetefeldt

IK the dry-crushing of ores, either by stamps, rolls, or other machinery, it is essential that the material should be free from moisture. Hence a contrivance which effects this with economy, and is of durable and compact construction, is a great desideratum. It is claimed for the below-described shelf dry-kiln, that it possesses these qualifications in a high degree. The construction of the shelf dry-kiln is based on the Hasenclever principle. That is to say, a number of inclined shelves are arranged zig-zag above each other in a vertical shaft, having openings or slits where they meet, on which the ore rests in a stratum, the thickness of which is governed by the width of the slits and the inclination of the shelves. If a portion of the charge is removed at the end of the bottom shelf, a sliding motion of the ore takes place on all shelves above, and the top shelf is replenished from a hopper set over it. It will be seen that the shaft is divided by the shelves into a number of triangular prismatic spaces. Through these the hot gases from a fireplace are made to circulate, each space communicating with the next one by a flue arranged in the sidewall of the shaft. These flues being located on alternate sides of the shaft, a continuous passage is formed through the whole structure. After thus stating the principle of the construction, its details will be easily understood by reference to the drawings, Fig. 1 to Fig. 5. The drawings, Fig. 1 to Fig. 4, represent two kilns united into one structure. The cast iron shelves(a) are 2 feet 4 inches wide and 5 feet long, with sides and a back 4 inches high, and are cast a full halfinch thick. How they rest on the brackets(d), and interlock each other, is shown in Fig. 5. Three such shelves, with an inclination of 38&apos;) are placed in one row in a brick shaft 7 feet 1/2 inch wide and 4 feet deep. The ore hoppers(g) rest on the iron bems(f). At the end of the bottom shelves are the discharge-doors(b), with shoots projecting beyond the front wall. A swinging apron(e) keeps the ore in place. By dropping it a car below the shoot is filled with dry ore. A number of extra-large pieces of ore may cause a stoppage in the slits ; for such an emergency the openings(e) are provided, through

Jan 1, 1884

IF you do not make the disc at the same time as the core and as part of it, it is necessary to make it by itself. This is done by spreading on a board or other flat surface a layer of clay as thick and wide as [88] the disc that you made at the feeding head of the first pattern of the gun. When it is dry, mark it exactly with compasses and then, cutting with a chisel or rasp, make it fit exactly into the empty space at the head. Likewise, make a hole just as wide as the thickness of the core exactly in the middle of this clay disc. When you have put the disc in its place in the mould and then pass the core through this hole, it passes exactly through the center of the mould in such a way that it meets the iron ring that you put at the foot of the mould for this purpose. As I said above, if&apos; you do not make it as part of the core, it is necessary to proceed in the aforesaid way. But if&apos; you wish to make it attached to the core (which I like better because it can be done more accurately) make a

Jan 1, 1942

By Robert B. Sosman

The chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily I I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting On a paper that I had recently published27 On "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of of Howe&apos;s interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. Scope of the Lecture During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyro-metric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the united States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the ((temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that " temperature of the furnace " is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1949