Search Documents

By John W. Bell

The aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½-ft. Huntington mill was used.

Jan 1, 1918

By D. A. Crerar, R. L. P. Kleinmann, R. R. Pacelli

A bacterium, Thiobacillus ferrooxidans, is of prime importance in the formation of acid drainage from pyritic material. Above pH 4.5, T. ferrooxidans increases initial acidification; below pH 4.5, it allows acidification to continue by oxidizing Fe2 +. Below a pH of approximately 2.5, the activity of F3+ is significant and results in steady-state cycling between oxidation of pyrite by Fe3 + and bacterial oxidation of Fe2 +. Laboratory and field tests demonstrate that inhibition of T. ferrooxidans by controlled release of anionic detergents can inexpensively reduce pyrite oxidation and acid formation.

Jan 1, 1982

By K. H. Coats

This paper presents the development and solution of a mathematical model for aquifer water movement about bottom-water-drive reservoirs. Pressure gradients in the vertical direction due to router flow are taken into account. A vertical permeability equal to a fraction of the horizontal permeability is also included in the model. The solution is given in the form of a dimensionless pressure-drop quantity tabulated as a function of dimensionless time. This quantity can be used in given equations to compute reservoir pressure from a known water-influx rate, to predict water-influx rate (or cumulative amount) from a reservoir-pressure schedule or to predict gas reservoir pressure and pore-volume performance from a given gas-in-place schedule. The model is applied in example problems to gas-storage reservoirs, and the difference between reservoir performances predicted by the thick sand model of this paper and the horizontal, radial-flow model is shown to be appreciable. INTRODUCTION The calculation of aquifer water movement into or out of oil and gas reservoirs situated on aquifers is important in pressure maintenance studies, material-balance and well-flooding calculations. In gas storage operations, a knowledge of the water movemenr is especially important in predicting pressure and pore-volume behavior. Throughout this paper the term "pore volume" denotes volume occupied by the reservoir fluid, while the term "flow model" refers to the idealized or mathematical representation of water flow in the reservoir-aquifer system. The prediction of water movement requires selection of a flow model for the reservoir-aquifer system. A physically reasonable flow model treated in detail to date is the radial-flow model considered by van Everdingen and Hurst.1 In many cases the reservoir is situated on top of the aquifer with a continuous horizontal interface between reservoir fluid and aquifer water and with a significant depth of aquifer underlying the reservoir. In these cases, bottom-water drive will occur, and a three-dimensional model accounting for the pressure gradient and water flow in the vertical direction should be employed. This paper treats such a model in detail — from the description of the model through formulation of the governing partial differential equation to solution of the equation and preparation of tables giving dimensionless pressure drop as a function of dimensionless time. The model rigorously accounts for the practical case of a vertical permeability equal to some fraction of the horizontal permeability. The pressure-drop values can be used in given equations to predict reservoir pressure from a known water-influx rate or to predict water-influx rate (or cumulative amount) when the reservoir pressure is known. The inclusion of gravity in this analysis is actually trivial since gravity has virtually no efFect on the flow of a homogeneous, slightly compressible fluid in a fixed-boundary system subject to the boundary conditions imposed in this study. Thus, if the acceleration of gravity is set equal to zero in the following equations, the final result is unchanged. The pressure distribution is altered by inclusion of gravity in the analysis, but only by the time-constant hydrostatic head. The equations developed are applied in an example case study to predict the pressure and pore-volume behavior of a gas storage reservoir. The prediction of reservoir performance based on the bottom-water-drive model is shown to differ significantly from that based on van Everdingen and Hurst's horizontal-flow model. DESCRIPTION OF FLOW MODEL The edge-water-drive flow model treated by van Everdingen and Hurst1 is shown in Fig. la. The aquifer thickness b is small in relation to reservoir radius rb. water invades or recedes from the field at the latter's edges, and only horizontal radial flow is considered as shown in Fig. 1b. The bottom-water-drive reservoir-aquifer system treated herein is sketched in Fig. 2a and 2b. Here the aquifer

By Y. A. Rocher, J. E. Dorn, L. A. Shepard

Creep activation energies for single aluminum crystals favorably oriented for shear by (010) [101] glide were detemined over the temperature range from 78" to 900°K. Observations of slip bands on the specimen surface were made in conjunction with the investigation. From 78" to 780°K, the activation energies obtained in this imestigation agreed closely with those previously found for creep by (111) [101] slip. Between 78" and 140°K, the activation energy was identified with the Peierls process, while between 260°and 780°K the activation energy was close to that for cross-slip. The coarse wavy slip bands nominally parallel to the (010) plane observed above 260°K were attributed to fine cross-slip. From 800" to 900°K, unusually high apparent activation energies ranging from 28,000 to 54,000 cal per mole were obtained. These apparent activation energies were attributed to re crystallization. AS illustrated in Fig. 1, a recent investigation1 has shown that creep of aluminum single crystals by the (111) [i01] mechanism is controlled by three unique processes, each of which is characterized by a single activation energy which is independent of the applied stress and the creep strain. A comparison of the observed activation energies with theoretically calculated values permits a fairly clear identification of the three operative creep processes. Below 450°K, where the activation energy for creep is 3,400 cal per mole, the deformation is controlled by the Peierls process, the activation energy for creep agreeing well with that calculated by seeger2 for the energy required to nucleate the motion of a dislocation loop against the atomic forces of the lattice. Between 590° and 750°K, the observed activation energy for creep of about 28,000 cal per mole agrees well with the energy necessary to induce cross-slip. Seeger and schoeck3 estimate that the activation energy is about 24,000 cal per mole whereas Friedel4 recently calculated this activation energy to be 28,000 cal per mole. Above 800°K the activation energy of 35,500 cal per mole that was observed for creep agrees well with that estimated for self-diffusion in aluminum.= In this range the operative rate-controlling slip process has been clearly identified as that arising from the climb of edge dislocations. The objective of this investigation is to ascertain whether a single crystal of aluminum favorably oriented for simple shear in the [loll direction on the (010) plane might exhibit uniquely different activation energies for creep from those obtained previously for (111) [101] slip. Whereas the exis- tence of such unique activation energies would constitute incontrover table evidence for new mechanisms of slip, the absence of any new activation energies might suggest that slip of aluminum is confined to the (111) [loll mechanism. Several factors prompted the selection of the (010) [101] orientation for study. First, there are more reported observations of (010) [loll slip than of any other nonoctahe-dral mechanism.8-10Secondly, Chalmers and Martius1l have concluded from considerations of the energies of dislocations that (010) slip is the second most favored mechanism in face-centered-cubic metals. Finally, favorable orientations for simple shear by the (010) [loll mechanism provide the least favored orientation for slip by the (111) [101] mechanism. EXPE-RIMENTAL PRO-CEDURE The high-purity aluminum stock, specimen preparation, shear fixture, extensometry, and experimental technique used in this investigation were the same as those previously reported.' Single-crystal spheres grown from the melt of 99.995 pct pure Al* were _ *The high-purity aluminum used in this investigation was graciously given by the Aluminum Company of America. oriented, carefully machined into dumbbell-shaped shear specimens, annealed, and chemically polished. The finished specimen had a central reduced section 0.190 in. wide and 0.590 in. in diam and 1/4-in. grip sections at both sides, 0.690 in. in diameter. The specimen was oriented in the stainless steel grips of the shear fixture with the (010) plane perpendicular to the dumbbell axis and the [loll direction parallel to the stress axis within 2 deg. Creep activation energies were calculated in the previously described manner1 from determinations of the instantaneous change in shear strain rate produced by an abrupt 15 to 20 deg increase or decrease in test temperature. If is the instantaneous strain rate at strain y and temperature T1, and ?2 the instantaneous rate at y and T2,

Jan 1, 1960

By D. G. Peterson, W. J. Guay

The extraction of gold from refractory ores containing activated carbon and various types of carbon compounds is being done commercially for the first time at Carlin, Nev., by Carlin Gold Mining Co. Oxidation of the carbonaceous materials to CO and CO,- is accomplished by the introduction of chlorine into an aqueous pulp. The chlorine reacts with the limestone in the ore to form calcium hypochlorite which in turn reacts with the carbonaceous matter to form calcium chloride, CO, and CO.. Following the oxidation treatment the ore is cyanided in the conventional manner. For the first six months of operation the plant averaged 83% extraction at a feed rate of 500 tpd and a consumption of 28.4 lb chlorine per ton of ore which showed only 33.5% extraction by conventional cyanidation without the oxidation pretreatment.

Jan 1, 1974

By Robert Mehl

THE importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.1 It is a structure produced by the precipitation of a new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Bessemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstätten figures.4 Osmond5 observed structures in a steel ingot analogous to those found in meteorites. Arnold and McWilliams6 obtained (and recognized) a

Jan 1, 1930

By Franz Wever

The importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.l It is a structure produced by the precipitation of a, new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Ressemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstatten figures.4 Osmond Observed structures in a steel ingot analog-ous to those found in meteorites. Arnold and Mc William6 obtained (and recognized) a

Jan 1, 1931

By Clifton W. Livingston

So many factors influence blasting results that theories and rules are usually dismissed as impractical; the practice prevailing today is arrived at by cut and try. Usually the first step is to experiment with drillhole patterns and spacing until an arrangement is found that gives best results. The next step is to experiment with different types of explosives and sequences of blasting until the most satisfactory degree of fragmentation is achieved and until no further reduction in cost is immediately apparent. Improved fragmentation is generally attributed to the type of powder used, the sequence in which the holes are blasted, or the use of millisecond delays. Various types of drill rounds have been evolved in tunneling operations, underground development headings, and stoping, and various patterns of blasting in open pit mines and quarries. These practices usually are carried from mine to mine or from district to district, and great skill is exercised by those experienced in the art of blasting.

Jan 1, 1960

By Arthur Lake

Within the past few months I have had occasion to visit and examine the area of country in Gunnison county locally called the Gold Belt and extending from the Cebolla river on the west to the head of Taylor Park and the Sawatch range on the east. The region including the "belt" may be hided topographically into two parts, a northern and a southern one. The former is characterized by lofty mountains and deep canons, with occasional parks and wide valleys. Most of it is included in the granitic system of the Sawatch range, with local patches of the Palaeozoic sedimentary rocks, more or less traversed by great bodies of porphyry and other eruptive rocks. The southern portion, on the other hand, is characterized by comparatively low, rounded hills of schist and sahistose gneisses, underlain by coarse, massive granite, which outcrops locally in small, and sometimes in large, patches. These hills also sometimes form table-lands by reason of overflows of lavas, such as andesitic breccia, rhyolite, trachyte and basalt. The leading geological feature is that of a schistose area of width and extent unusual for Colorado. These schists and gneisses are of pre-Cambrian age; but whether assignable to the Algonkian or to some older system has not been determined. The granite which occasionally outcrops from beneath these schists is, I think, of true eruptive character, since its mode of occurrence indicates a once molten, or at least highly viscous or plastic, condition. Thus, we may observe, included in its mass, numerous fragments of schist, almost like a coarse, volcanic breccia. Again, at its immediate contact with the schists, which often stand vertically upon it, the pediments of the latter are fused into the granite, and granite tongues and veins run up amongst the schists, as only a molten or viscous

Jan 1, 1897

By R. E. Reed, C. J. McHargue

Poly crystalline aluminum specimens having random and diffuse (001) initial orientations were reduced 90 pct in area at room temperature by drawing, extruding, and swaging. Although each procedure produced the duplex (001)- (111) texture, there were marked dqferences in the relative amounts of each component. This also produced variations in the tensile properties of the aluminum rods. It is generally agreed that the fiber texture found in aluminum rods consists of a strong (111) and a weak (001) component after reductions in area of 90 pct or more. An examination of data summarized in recent reviews'-3 shows much spread in the values for the relative amounts of the two components reported by different investigators. That the initial orientation has a marked influence on the final texture even after reductions in area greater than 90 pct is well-documented.4-7 Another factor which may influence the relative amounts of the two components is the method of fabricating the wires or rods. Barrett and ~assalski' state that the center of wires formed by rolling, swaging, and drawing have the same textures. The data cited in support of this conclusion came from qualitative X-ray techniques. In recent years there has been renewed interest in correlating the type of preferred orientation with such parameters as stacking fault energy and onset of mechanical twinning.'' Since these analyses have often used many sources of data, it is essential that the data be evaluated for the effect of fabrication variables. In this study we have produced aluminum rods by drawing, swaging, and extruding and have quantitatively determined their textures. All specimens had the same purity and fabrication temperature, and the amount of deformation and the starting textures were determined. We have compared our results with published studies on similar materials and fabricating parameters. We have also compared results from the same three fabricating procedures for single-crystal specimens in three instances. EXPERIMENTAL PROCEDURE The aluminum was 99.99+ pct with the only detected impurities being (by weight) 0.002 pct Cu, 0.001 pct Si, and 0.001 pct Mg. Cylinders a in. in diam by 1 in. long with a fine-grain random texture were made by the following method. Cubes 1+ in. on a side were machined from 2-in.-diam ingots. These cubes were slowly pressed about 30 pct in each of the cube directions. The material was recrystallized by annealing 1 hr at 350°C. Three deformation-anneal cycles produced the desired material. Polycrystalline specimens with a diffuse (001) texture were made by casting into a graphite tube 1 in. ID, li in. OD, by 8 in. long which had been preheated to 900°C. One end of the tube was placed on a water-

Jan 1, 1969

By John B. Hastings

The occurrellce of such a large amount of gold in the Hart-eel granite, even though the surmised existence of similar areas is not new, brings freshly to mind the pegmatite type of mag-matic differentiation lately brought again to attention by occurrences at Silver Peak, Nev., described by Spurr; and in Alaska, described by both Spurr and Brooks. In both localities granitic rocks or dikes are thought to pass into metalliferous quartz-veins. An interesting association in this connection is the occurrence of diamonds in residual pegmatitic clay of Sail Juao de Chapado, Brazil, described by Derby :' (P. 142) "Bodies of pegmatite are quite common in the older rocks of Brazil, both in the diamond regions and elsewhere, occurring not only in the gneiss and granite, but in the schistose series as well. Those that have been examined are dike-like in their mode of occurrence and granitic in composition.'' (P. 143) '" The question of the eruptive or secretionary origin of pegmatites has long been a subject of discussion among geologists.... The recent studies .. seen] to have clearly established that most if not all of them are essentially eruptive masses, though possibly modified in some way by aqueous agencies. Even before becoming acquainted with the literature of the subject this view had seemed to me to be the only acceptable one as regards the typical pegmatites of Brazil." What is pegmatite ? J. F. Kemp says :2 "... veins or dikes—it is an open question which is the more correct term— are met formed of very coarsely crystalline aggregates of the same minerals that constitute granite. These are called pegmatite and in them is the home of graphic granite, the curious intergrowth of quartz and feldspar, such that a cross fracture of the blades of quartz suggests cuneiform characters.... In regard to the larger veins or dikes it seems improbable that true igneous fusion could have afforded such coarsely crystalline aggregates, and so we are forced to assume such abundance of steam and other vapors, i.e, mineralizers, as to almost, if not quite, imply solution."

Jan 1, 1909

Horace F. Lunt, York, Montana* :—Two years ago I visited the region described by Mr. Jennings and assisted in the examination of a somewhat similar group of deposits in the White Mesa sandstone on the Navajo Indian Reservation, 125 miles north of Flagstaff and 50 miles east of the Kaibab plateau. There, the Triassic red sandstone is less than 200 ft. thick, and is overlain by a stratum from 200 to 250 ft. thick of white sandstone, which gives the name of " White Mesa" to that locality. The white sandstone shows all phases of crossbedding in great complexity, and evidently marks a period of oscillation and subsidence of the water, or an elevation of the land, at the close of a geological epoch. The prevailing color is white or gray, but occasionally it is red. In structure, it is composed of well-worn grains of quartzsand, from which most of the cementing material has been leached out, leaving it soft and friable. Possibly the cement was ferruginous, as is indicated by occasional traces of red color. The copper-deposits consist of a replacement of the cement of one particular cross-bedded stratum of the sandstone by chrysocolla, having also at times various quantities of tenorite in grains or masses. Some specimens of the ore contain as much as 32 per cent. of copper. Generally the copper-deposits are a few hundred cubic feet in size, and no strict line of demarcation is shown between them and the surrounding sandstone, the bluish-green color of the chrysocolla gradually fading into the white of the sandstone. The ore is apparently associated with small vertical crevices or fissures. Some of the deposits show a distinct vein-structure, while others do not. The origin of the ore is not very clear. Undoubtedly the solutions, coursing through the crevices noted above, played a prominent part in its deposition, as possibly

Jan 1, 1904

By Warden A. Moller

The Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of hlukden, the oapital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Xiukden, consists of a long narrow valley, running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 30 ft. of alluvium, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lavas and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent. is good coal. The seam dips to the north conformably with the shales, at angles of from 25 to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut oft' by the northern hills. The coal-bearing shales extend east and west for a length of about SO miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal—quick steam-raising and poor stacking qualities. Pieces of resin, varging in size from

Jan 1, 1911

By George S. Rice

THE wide scope of the causes and effects of ground movement and their interrelation to various kinds of mining and geological conditions are not always understood. Minimizing of roof movement by selection of suitable mining methods is closely allied to the problem of obtaining maximum safety in mining, but there are other questions involved: for example, mechanical developments which increase the production of ore and other minerals per shift or unit of labor but which, though highly ingenious, may increase hazards. More- over, the newer mobile loaders need much space for operation with longer protecting roof spans. Another problem emphasized by mechanization is the incompleteness of extraction of mineral, as there is no governmental requirement (except for limited leases on the public domain) in this country, as in European countries, and loss of coal in pillars is accepted by mine operators rather than risking the loss of an ex- pensive loading machine from a heavy roof fall. The extent to which losses of coal in mining are now being incurred is conjectural, for it has been fifteen years since there has been a comprehensive survey. In that study a loss of slightly over one-third of the coal in both anthracite and bituminous mining was indicated.

Jan 1, 1939

By W. McDermott

It is well known that many so-called free-milling silver arcs are so classed more from their value necessitating a cheap process than from a real adaptability to raw amalgamation. Such low--grade ores, carrying more or less sulphurets, are more profitably treated by a cheap rapid process than by the more effective but costly process of roasting arid amalgamation. The tailings are sometimes crudely concentrated, or, after lying and becoming partially oxidized, are again worked in pans. Of late years, by the use of improved methods of concentration, many old low-grade tailings-piles have been reworked to a good profit; and in some improved mills arrangements are made to concentrate before or after amalgamation, thus making a single treatment in mill suffice. It is self-evident that on a low-grade ore a small increase in percentage saved is of no commercial advantage if accompanied by a material increase in cost, and therefore a cheap and continuous system of work is the real necessity, if a fair saving be effected. As an illustration of the possibilities of combined concentration and amalgamation on some ores, the following results of a working test at the New York Ore-Milling and Testing Works will be of some interest. The ore treated was a hard white quartz from Mexico, carrying a very small percentage of finely divided sulphurets, chiefly iron

Jan 1, 1885

By M. Gensamer

IT has been suggested by a number of people that it would be worth while for some one to attempt to summarize or condense the proceedings of this symposium. This task has fallen to me as organizer and co-chairman. Its difficulty will be appreciated by anyone who attempts to read the whole proceedings. It is therefore with trepidation that I offer the following digest. In recent years there has been a renewal of interest in America on this subject of the cohesive strength of materials, and a growing appreciation of the need for a better theory of cohesion failure. The theories of elastic action and plastic action are well developed, particularly the former. The theory of plastic action is still in the course of development, but it is well along. Plastic action is terminated by cohesion failure and what is needed is a theory that will tell us when to expect the cohesion failure. In the past it has generally been assumed that cohesion failure will occur when a critical value of the maximum tensile stress has been reached. Many experiments have shown that this is not strictly true, and this symposium concerns itself with the failures of this simple hypothesis, and with the efforts that have been made to devise a more satisfactory theory. The most active contributor in recent years to knowledge in this field is Dr. McAdam, and he was asked to open the symposium with a summary or condensation of his papers and views. Undoubtedly it is presumptuous to attempt a still greater condensation, but perhaps it will be useful, because even his contribution to this symposium contains no summary, no concise statement of just what his contribution has bees. Dr. McAdam makes two main points. The first is that the cohesive strength is not a single valued quantity, but that it is a function of all three principal stresses and hence must be represented diagrammatically by a surface in a three-dimensional figure. Dr. McAdam has attempted so to delineate the cohesion limit, basing his

Jan 1, 1944

By T. Egleston

THE direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German bloomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Not¬withstanding the improvements which have been made in the construction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The Dame of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process. * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By T. Egleston

The direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German b1oomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Notwithstanding the improvements which have been made in the constrnction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The name of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of' German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process.

Jan 1, 1880

By R. J. Watson

IN an earlier paper, Ehrenburg and Watson1 published the develop-ment for a potential function by which it is possible to obtain the electric potential at points on the surface of the ground when a current I passes between two electrodes and the subsoil is composed of parallel, homo-geneous layers. In view of the continued interest in the resistivity method of electrical prospecting, the author has considered it desirable to publish the results of a number of theoretical studies making use of this potential function, and also the results of a considerable number of tests with models designed to show the soundness of the mathematical theory. It is hoped that these results will prove how erroneous the various empirical rules for depth determination may be. It has always seemed puzzling to the author that one can find, in papers published comparatively recently, statements upholding empirical rules for depth determination, and attributing most of the irregularities of resistivity curves to vertical discontinuities in resistivity in the subsoil. It would indeed be fortunate for the geophysical investigator if such a simple rule held. However, numerous investigators have proved both theoretically and by the success of their field work that such a rule does not hold, even by a" rough approximation" in many cases. On the other hand, as is shown in the development to follow; if the underground conditions are favorable it is possible for such empirical rules to give a satisfactory depth determination. Authors should be more careful about making such sweeping state-ments about the accuracy of these empirical rules because the relative simplicity of the field work places the method in the hands of any inter-ested experimenter, and he is likely to become completely disgusted with the method after he has made several obviously wrong interpretations by empirical rules.

Jan 1, 1934

By CHARLES E. W.

I. LOCATION. THE Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low ridge of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. CLIMATE AND VEGETATION. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera-ture is generally from 60° to 70° F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100° F. in the day-time, while 115° F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1906