Search Documents

By M. R. Tek, K. H. Coats, D. L. Katz

The nature and the limits of validity of Darcy's law US applied to the flow of natural gas through reservoirs has been considered in order to resolve some controversial aspects of the effect of turbulence on pressure drops. The equivalence between various concepts and viewpoints advanced in the past by several investigators to explain how and why a gas well does not necessarily perform according to Darcy's law is shown. Starting with generalized equations of flow of fluids through porous media, a partial differential equation has been derived which accurately represents the flow at all rates. This equation has been numerically solved using an IBM 704 digital computer. The results permit plots of unsteady radial pressure distribution curves from which specific isochronal backpressure curves may be constructed. These back-pressure curves show the effect of the ,8 factor on the slope of the back-pressure curve. The calculations further indicate that the drainage radius for a gas well in turbulent flow propagates at a rate dependent upon the rate of production at the wellbore. This is quite different from the case with liquid flow or natural-gas flow in laminar regime. Additionally, the effect of reservoir inhomogeneities and crossflow between layers of different permeability on the back-pressure performance of gas wells has been conridered. In light of the current numerical results the significance and linlitation of the rate of flow function Y proposed by Smith" has been discussed. INTRODUCTION The relationship between the pressure drop and flow rate in problems of fluid flow through porous media is known to be affected by the nature of flow through the porous matrix. It has been observed by many that, for a range of flow rates, the pressure drop remains proportional to the rate of flow. When some flow rate is reached, however, it is usually observed that the pressure drop gradually begins to increase more than proportionally to the flow rate. It is well known that this phenomenon was first observed by Osborne Reynolds in 1901 in experimenting with flow through pipes. In his classical experiments, Reynolds made visual observations on the condition of streamlines evidenced by injecting a dye into water flowing through glass tubes. In these experiments, the abrupt transition between steady, "streamline, laminar" flow and unsteady random turbulent flow was found to be a function of the dimensionless group (Dvp/u), now known as the Reynolds number. During these experiments, in addition to observations on the nature of flow regimes, the proportionality between flow rate and pressure drop in laminar flow was contrasted with the nonlinearity between these variables in turbulent flow. Fancher and Lewis' reported data on various consolidated and unconsolidated sands in 1933. Their conclusions were that ". . . the flow of fluids through these porous materials closely resembles that through pipes; that there is a condition of flow in porous systems which resembles viscous flow, another which corresponds to turbulent; that the change from one type to the other takes place at a definite and reproducible condition for each system". In 1947, Brownell and Katz published a method to predict the laminar and turbulent flow behavior from the particle size, bed porosity and the particle sphericity, employing the friction factor-Reynolds number charts for pipes. Several investigators have verified the work of Fancher, Lewis and Barnes and presented their data as friction factor-vs-Reynolds number plots.' The equation which would represent the pressure gradient over the whole range of velocity must have an added term over that represented by Darcy's law. Accordingly, the pressure gradient necessary to sustain flow at the velocity (v) through a porous medium may be represented by the following equation, suggested by Forscheimer." The nature and the range of validity of Darcy's law has been the subject of studies by many investigators over the past years. While everyone seemed to agree on the need for a quadratic correction term to Darcy's law to make it effective over the range of velocities, the concept of inception of turbulence and the use of the term "turbulent flow" remained controversial. Some fluid dynamicists define turbulence as a flow

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By T&apos Kê, ing-sui

INTRODUCTION ACCORDING to the classical theory of elasticity, the elastic portion of the stress-strain curve is represented by a straight line. Such a representation implies that there is a linear relationship between strain and stress and also that strain is a single-valued function of stress and vice versa. Actually, such a one-to-one correspondence between strain and stress does not exist in real metals. A well-known example is the elastic after-effect on unloading. Another familiar example is damping or internal friction, that is, the dissipation of energy attending vibration. In an extensive review of such phenomena, Zener1,2 has proposed the term "anelasticity" to denote that property of a solid in virtue of which strain is not a unique function of stress in the non-plastic region. The phenomena arising from anelasticity are called anelastic effects. The measurements on inelastic effects are, important in many fields of metals technology. Thus, in precise instruments such as watch springs, difficulties often arise from the slight dimensional changes after fabrication. The internal friction or damping capacity of metals is often an important factor in deciding whether they are appropriate for instruments in which there are accompanying vibrations.' However, for metal scientists, the study of anelastic effects furnishes a powerful tool for understanding many properties of metals in terms of their microstructures or atomic interactions. In order to utilize the anelastic measurements to their fullest extent for acquiring such information, the experimental studies of anelasticity must be interpreted by appropriate mathematical analysis. For a great many problems, however, the necessary information often can be obtained by general qualitative arguments. From the definition of anelasticity, any physical changes occurring in a specimen as a result of the applied stress will cause anelastic effects if such physical changes are accompanied by a delayed change of elastic strain. Under these circumstances, we have the condition that strain lags behind the stress. We may mention the stress-induced transportation phenomena as examples. These include the stress-induced thermal diffusion," the stress-induced diffusion of particles,8-12. and the stress-induced viscous slip along the microelements in metals.12-15 The differential equations describing the microscopic mechanism in these phenomena lead to relations in which stress is linear with respect to strain (and/or their derivatives). Thus if we can - demonstrate that the superposition principle is valid under the circumstances in which the anelastic effects are observed, we would expect in. the macroscopic relation a linear relationship between stress and strain and their derivatives. This report is to describe a number of anelastic effects observed in alpha-iron, and an attempt is made to derive valuable information from a critical study of these

Jan 1, 1948

LEAD and tin mixed together make an alloy through an attachment of natural affinity which they have with each other, so that when they are mixed it is difficult to recognize by the sight which one it is, if the essences of their qualities are not surpassed by more than half. If, indeed, one can be recognized, it is the tin which gives off a certain sharp odor to the sense of smell, besides having a greater hardness and whiteness. The best of these is the one that is the purest in its kind. In the alloy of tin it is the one that is the whitest and hardest, or, when it is bent or some thin end of it is held tightly by the teeth, is heard to crackle as frozen water does. Because this happens more with this than with other metals, I do not wish now to inquire into it. It is enough that it be a sign for recognizing when tin is pure or mixed. Pewterers say that it should be joined in alloy with lead and that it is better for working when it contains four or six pounds to the hundred because it makes it softer to the hammer and more fluid in casting. But I do not like to hear this, even if all they say is true, for I see that the tin that comes from England, when worked as well as in cakes that show it to be pure, is much more beautiful and better in all works than is that made in Venice. And I believe that it is not better for any work when mixed than when pure, except for the advantage of the master who, if he does nothing else, sells lead that is worth little for tin that is worth much. I find that when mixed it serves in only two things. One is when it is wished to make a solder for copper, for use when it is not worth while to solder the bottoms and large pieces of vessels with low-grade silver as should be done. The other is when master potters calcine it in order to make glazes and to apply white to their vases. I consider lead to be useless in all other works of any kind of metal, since it unites with none of the other metals of good company except tin.

Jan 1, 1942

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938

By K. L. Komarek

Based on theoretical and experimental evidence a discussion follows of the behavior of phosphorus -bearing iron ores in the R-N Direct Reduction Process and suggestions are made of methods of reducing the amount of phosphorus in the metallic end product. In ferrous metallurgy a direct reduction process is one in which iron ores are reduced to metallic iron with gaseous or solid reductants without the appearance of a liquid phase. A number of attractive features have induced several companies and government agencies to invest in the development of direct reduction processes. A summary of all direct reduction processes up to 1954 has been given by Barrett,' and Wiberg,2 and Willems3 have reviewed the most recent developments in this rapidly expanding field. Many difficulties have been encountered in direct reduction processes and the nature of these difficulties has varied from process to process. One problem common to almost all of them is the removal of phosphorus which is one of the reasons for the rather pessimistic outlook given by some government publications4'5 to direct reduction processes. In this paper an attempt is made to give a theoretical explanation of the variations in phosphorus removal observed in the R-NY Direct Reduction Process. However, many conclusions are general enough to be applicable to other processes. Most iron ores treated by the R-N process yield products lower in phosphorus than the original ore. A qualitative account of the factors has been given by Stewart, Reed, and Herasymenkoe but the erratic removal of phosphorus from some ores and the general importance of this problem make a more careful analysis of the theoretical aspects desirable. In the R-N process mixed ore or balled fines, ex-

Jan 1, 1963

By W. Hurst, R. E. Leeser, W. C. Goodson

Three aspects of gas deliverability are presented in this paper. The first treats with the gas deliverability or availability of a normal depletion-type dry gas field. Such encompasses not only the period of stabilized constant rate, but more so, the "tailings" when a fixed abandonment pressure is reached and the rate by necessity must decline. A comprehensive work plot is offered, developed from mathematics herein included, that removes the triai-and-errnr computations that attended such undertakings in the past. The second part treats with the discount factor of the open flow potential constant from what is observed initially in testing a gas well to what is evidenced when stabilization is reached. This prevails in tight formations, such as the Kansas Hugoton field which is offered as the example. The means of establishing this factor are pressure build-up curves which, as sustained by analytical deductions, reproduce this entire period of transient flow under conditions of a constant rate influx. Finally, what is offered in this paper is the deliverability performance of an exceedingly rich gas condensate field producing from a tight formation. The example shown is the Knox Bromide field in Oklahoma, producing from the Bromide formations. The results are ominous, showing early reduction in permeability to gas pow, due to the retrograde condensate forming in the pore space, with the attending early logging-up of these wells. The analytics of lowered permeability are incorporated in the gas deliverability formula along with the PVT data that gives the increased condensate liquid saturation as the gas flows to the well bore. This paper would not be complete without a critique oflered at the end. With the many gas wells now in production and those that have completed their life, there has been no factual information collected by any source as to what constitutes that permeability range where a gas well would be unimpaired in its gas deliverability by the presence of rich condensate content, and the lowered range where such would be harmful. This question confronts all producers. INTRODUCTION Various aspects of gas deliverability are presented in this paper that includes depletion-type reservoirs, deteriora- tion factor of the gas deliverability constant, and the performance of a rich gas condensate reservoir producing from a tight sand. With respect to the presentation of gas deliverability and its tailings for depletion-type gas reservoirs, one notes that this is essentially the information offered by every gas transmission company and producer appearing before the Federal Power Commission for Letters of Conveyance in the dedication of reserves. In the ordinary procedure, as many engage upon this study, trial-and-error calculations are included, particularly as apply to the tailings. For many years one of the writers has employed mathematical analyses to perform this step and avoid the complexities so associated. In the preparation of this paper these analyses have been amplified to include any slope n for the open flow potential relationship for which the tailings can be determined from Fig. 1. With reference to the deterioration or discount factor of the open flow potential constant as such occurs in the gas deliverability formula, this for the most part has been an unexplored subject. Although the issue first appeared in the Kansas Hugoton field, where such was surmised but only recently resolved, this situation of a deterioration of the gas deliverability constant can occur wherever dry gas production from a tight sand is encountered. The first concerted attacks upon this problem were the presentations of Hurst' and Goodson' before the Kansas Corporation Commission to show that transient fluid flow and unsteady-state flow formulas prevailed. This was amplified later before the Federal Power Commission3 to show that this deterioration factor could be identified from pressure build-up curves. This has been reported by McMahon.4 Its importance to the industry merits the review of these essential features in completing the program on the aspects of gas deliverability. Finally, as illustrated here, for a low permeability formation such as the Knox Bromide field where the gas is rich, representing some 165 bbl of condensate per MMcf of effluent gas, the gas deliverability can be of limited extent in the life of the field, leaving substantial amounts of condensate and gas unrecovered. In cases such as this, gas cycling is mandatory. This is particularly revealed by the fluid mechanics introduced here, employing factual field as well as laboratory data, to show this-restriction upon gas deliverability. PRESSURE DEPLETION What will now be offered is the study of gas deliver-

By G. H. Ashley

THE Pittsburgh coal bed stands today: as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? To the present it has contributed more than 2,530,000,000 tons of high-grade coal from Pennsylvania alone, worth nearly $4,000,000,000. Since 1910 it has added more than $2,500,000,000 to the value of Pennsylvania's mineral output. There is estimated to be about three times as much coal still in this bed as has been mined. To realize the full value of this wonderful bed it must be remembered that the figures given are for one State only. To them should be added the figures for the same bed from West Virginia, Ohio and Maryland. Furthermore, as known by man, this great deposit is only a fraction of its original whole. Outliers in Somerset County, Pa., indicate that its original extent in Pennsylvania in an east and west direction was more than two times its present extent. Add to that the northward extension as indicated by outliers in northern Allegheny, Armstrong and Indiana counties,, and it seems safe to say that its original extent was not less than three times the area at present underlain by it. And as the subjacent beds of the Allegheny group are found still further eastward and northward, it is at least a possibility that it originally covered an area many times its present area.

Jan 10, 1926

By F. H. Rhines, A. H. Grobe

The constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conven-tional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitu- tion of its alloys desirable. As a part of a program far the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (I43. 5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By A. H. Grobe, F. H. Rhines

The constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conven-tional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitu- tion of its alloys desirable. As a part of a program far the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (I43. 5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By J. P. Witherow

The blast-filmace plant of the Crozer Steel and Iron Company was built under contract by Witherow & Gordon, of Pittsburgh, Pa. The furnace is 70 feet high by 16 feet bosh, tunnel-head 12 feet 8 inches, and hearth 9 feet in diameter. The columns are 20 feet high above furnace level, below which they extend 2 feet. The shell is 23 feet diameter at bottom and 19 feet at top. The plate iron is 3/8 inch at bottom, and tapers to 1/4 inch, the top ring being 5/16 inch.

Jan 1, 1884

By P. Martinez, A. F. Hoyte, F. E. Senftle

The possibility of applying a neutron activation technique for silver exploration is considered. A mobile positive-ion accelerator type neutron source is used to irradiate a small area of rock or soil in situ. By using a short period of irradiation and gamma ray spectral analysis, a technique is shown for silver exploration. Two different mobile units are described. Laboratory and preliminary field tests both indicate that a sensitivity of less than 1 oz of silver per ton of ore can be achieved. The increasing consumption of silver for industrial uses and also for coinage has caused a serious shortage of silver in this country. The silver shortage has been reviewed and analyzed by kiilsgaard1 who concludes that, "The best hope for meeting future demands for silver is through accelerated exploration for precious ores." As almost all the exposed "bonanza" type silver deposits evidently have been found, it is urgent that some sensitive geophysical technique be found to detect large, extended, but generally low-grade, secondary ores, as well as hidden vein deposits. Silver is easily made radioactive by exposure to slow neutrons; hence a neutron activation method appears promising for locating silver deposits. The principles of mineral beneficiation using neutron activation techniques were discussed some years ago.2-4 Using the same approach, a preliminary description5 has been published of neutron activation as a mineral exploration tool. An exploration technique is described in which silver is made radioactive in situ and detected with a gamma radiation counter. The technique is similar to the well-known method used for uranium exploration. THEORETICAL CONSIDERATIONS Elemental silver consists of two isotopes, Ag107 and Ag109, having naturally occurring isotopic abundances of 51.4% and 48.6%, respectively. For short periods of irradiation of silver by thermal neutrons, the long-lived 250 day, half-life isotope, Ag110m, is not produced in significant quantities. However, significant quantities of 2.3 min half-life Ag108 and 24.5 sec half-life Agl10 are formed by the following reactions. Ag108 and Agl10 emit a 0.44 Mev (million electron volts) and a 0.66 Mev gamma ray, respectively. Ag107 + n + Ag108 (2.3 min) Ag109 + n + Ag110 (24.5 sec). Because of the large capture cross section (110 barns) of Ag109, and short half-life of Ag110 (24.5 sec), the 0.66-Mev gamma ray is the most prominent emission from silver for neutron activation periods of about a minute's duration.* The 0.44-Mev gamma ray from Ag108 will also be present, but will be one or two orders of magnitude lower in intensity. The decay scheme of Ag110 is shown in Fig. 1. If the neutron irradiation time is limited to about 100 sec, the Ag110 activity will essentially reach saturation and can be used to detect the presence of silver. In a neutron flux of 10 8 neutrons/cm2/set, the induced 0.66-Mev activity in 1 g of silver will be about 2 x 107 disintegrations per sec. This is about 1000 times the measurable gamma activity of 1 g of uranium in equilibrium with all its decay products; hence there is ample activity for detection. Under the same conditions of activation, most of the other elements do not reach this relatively high disintegration rate. Although this is in favor of the proposed technique, other problems must be considered. For mobile operation, it is desirable to obtain the largest neutron flux to weight ratio. Hence we have used a small 150-kev accelerator-type neutron source rather than an isotopic source such as an americium-beryllium neutron source. By use of remote control system, an accelerator-type neutron source can be safely used without the massive shield required for an isotopic source. Moreover, an accelerator-type source is more versatile in that it allows one to use a flux of either 14-Mev or 3-Mev neutrons, depending on whether a tritium or a deuterium target is used. With a 14-Mev generator, one can obtain a flux of 10 9 neutrons/cm 2/sec, and with a 3-Mev generator, the flux is generally two orders of magnitude less. Although silver will become activated with either generator using proper moderation, detection may be

Jan 1, 1968

By Rupert Spivey

Kennecott Copper's Chino mine is one of the oldest copper mines in the United States, having been operated by the Spaniards as early as 1800. At that time haulage methods were indeed primitive. Indians brought the ore up on "chicken ladders" in leather buckets. It was then melted into crude bars and hauled to Chihuahua by mule train. There are still remnants of the old trails near the present pit where the mule hooves cut grooves in solid rock. The mines were worked as underground operations off' and on until open-pit mining was started in 1910 by John Sully and Daniel C. Jackling. Since that time many haulage methods have been used: mule carts, steam and electric trains and finally large haulage trucks, now believed to be the best method for this mine. The general shape of the pit is oval with dimensions of 1% miles by 1% miles. Working benches are 50 ft high, with the bottom bench at 5750 ft and the top at 6450 ft above sea level.

Jan 1, 1964

By Harrison Everett Ashley

Slimes are usually defined as all material passing a certain sized sieve, which is invariably the finest sieve employed by each metallurgist in his tests; 100-mesh and 200-mesh have been taken as the limits by different writers in recent volumes of the Transactions; 150-mesh is common practice. The reader of the first two volumes of Richards' is impressed by the inflexibility with which all grinding-arrangements are praised or condemned according as they make little or much slime. Until recently, one of the principal aims of the mill-man was to keep down the slimes. He was obliged to have separate apparatus for sand- and slime-treatment. The latter was sometimes puzzling and erratic. Often it was found most economical to omit treatment of the slimes entirely, or to store them in immense basins or heaps, waiting for possible future improvements in methods of treatment. Recently, improved processes of agitation and filtration have made possible the successful extraction of values from many slimes. The tendency, when the metal is exceedingly finely disseminated, is to cut out all sand-treatment and to slime everything. These processes have been almost entirely mechanical in their conception, and it is the object of the present paper to show that certain chemical considerations may greatly hinder or assist their successful operation. It has long been a source of dissatisfaction to chemists that their analyses fail to be of much help to the clay-worker; that it is a matter of common occurrence for clays of closely identical ultimate chemjcal constitution to show the widest possible divergence in physical properties.

Jan 1, 1911

By G. A. Moore, D. W. Williams, C. E. Sims

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By C. E. Sims, G. A. Moore, D. W. Williams

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. 'The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.' Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By John T. Norton

In spite of the very general errlployment of nitride hardening, there is still considerable doubt as to the real nature of the mechanism involved. Experience has shown that the addition of small amounts of hardening elements to iron or steel results in a wide variety of desirable properties in a nitrided case. Perhaps the foremost of these elements is aluminum and in this investigation an attempt has been made to study the behavior of aluminum during the hardening process. It is believed that the establishment of a complete atomic picture of the metal at various stages of the process will indicate the relationships between the several kinds of atoms and their individual influences on the physical properties in a clear and direct fashion. A consideration of the problem suggests a surprising similarity between the mechanisms of nitride hardening and of age-hardening. It is now generally understood that age-hardening may take place by one of two distinct processes, the first involving the precipitation of a finely dispersed phase and the other being concerned with the modification of an existing phase. Following much the same line of reasoning, two theories of nitride hardening have been suggested. The first explanation, which has been generally discussed, particularly by Fry,' states in brief that the presence of aluminum causes the precipitation of aluminum nitride during nitriding and that this finely dispersed phase is the primary cause of hardening. The second explanation, which has not been published but which has been freely discussed by those interested in the problem, postulates the substitution of aluminum atoms for certain of the iron atoms in the several iron-nitrogen phases in the same manner that the substitutional iron-alurninurn solid solution is formed. The marked increase in hardness, as compared with the aluminum-free system, is attributed to the severe lattice distortion accompanying this replacement.

Jan 1, 1934

By B. B. Rath, Hsun Hu

In wedge-shaped bicrystals of zone-refined aluminum it is observed that (111) pure tilt boundaries migrate under the driving force of their own inter-facial free energy. The boundary velocity is a power function of the driving force. The driving force exponent decreases with decreasing angle of misorien-tation. For example, at 64O°C, the exponent decreased from 4.0 for a 40 deg to 3.2 for a 16 deg tilt boundary. An evaluation of the driving force acting on the boundaries during their motion indicates that for low driv-forces, up to about 2 x l03 ergs per cu cm, the velocity is relatively independent of misorientation, whereas at higher driving forces a 40 deg tilt boundary exhibits the highest velocity. The measured activation energy for boundary migration approaches that for bulk self-diffusion at low driving forces, decreasing from 33 to 27 kcal per mole as the driving force is increased from 1 x l0 to 5 x l03 ergs per cu cm. These results are compared with current theories of grain-boundary migration. In previous experimental studies of grain boundary migration the driving force has been limited to a difference in stored energy across the boundary. This stored energy has been introduced into the crystal either by prior deformation1-3 or by grown-in lineage structure. A part of the energy stored in the deformed crystal is released by recovery either prior to or concurrently with grain boundary migration, thus introducing an uncertainty as to the magnitude of the driving force responsible for grain boundary migration. The grown-in lineage structure, though thermally stable during annealing, neither provides conditions under which different levels of energy may be stored in the imperfect crystal nor provides a control of orientation difference across the migrating boundary of a growing grain. Furthermore, because of variation in the lineage structure, it is difficult to determine accurately the energy stored in the imperfect crystal. Several investigations of grain boundary migration during normal grain growth have also suffered from difficulties in estimating the driving force because of uncertainties in the principal radii of curvature.~ In the present investigation the velocity of pure tilt boundaries in zone-refined aluminum bicrystals of selected orientation (40, 30, and 16 deg around the [Ill] tilt axis) has been measured in the absence of a dislocation density difference across the moving boundary, thus eliminating the previous experimental difficulties. The driving force for boundary migration is derived from a gradient of the total interfacial free energy of the migrating boundary in wedge-shaped bicrystals. A similar method was attempted by Bron and Machlin in a study of grain boundary migration in silver. However, they found that one of the crystals was deformed and consequently the motion of the boundary was partly due to a difference of stored energy across the boundary. The observed behavior of boundary velocities as affected by the driving force is examined in the light of the predictions of the current theories of grain boundary migration.7"10 The effect of boundary misorientation on velocity is compared with the theory of " which is based on a dislocation core model for high-angle boundaries. EXPERIMENTAL METHOD Seed-oriented bicrystals of zone-refined aluminum, 2.5 cm wide, 0.5 cm thick, and 12 cm long, containing tilt boundaries with a common (111) axis, were grown from the melt in the direction of this axis. Spectro-graphic analysis, reported earlier,'' indicated the purity of the crystals to be 99.999+pct. Three such bicrystals containing 16, 30, and 40 deg tilt boundaries were used. Wedge-shaped specimens were prepared from these bicrystals by spark cutting followed by electrolytic polishing. The angle of the wedge was usually 40 deg and the specimens were usually 0.25 cm thick. The intercrystalline boundary was located within 0.2 to 0.5 cm from the tip of the wedge. Fig. 1 shows a section of an oriented bicrystal containing an outline of a wedge-shaped specimen. The crystallographic directions shown in Fig. 1 represent the orientation of one of the crystals (the larger section of the bicrys-tal); the orientation of the other crystal differs only by rotation around the common [lil] axis. The parallel faces of the wedge always corresponded to the common (171) planes in both crystals, whereas the orientation of the side faces varied, depending on the misorientation angle. The bicrystal orientations were determined

Jan 1, 1970