Search Documents

PRESIDENT W E WRATHER Washington, D C PAST PRESIDENTS Louis S CATES, New York, N Y CLYDE WILLIAMS, Columbus, Ohio VICE PRESIDENTS ' HOLCOMBE J BROWN,' Boston, Mass ROBERT W THOMAS, Ray, Ariz RLE V DAVELER, New York, N Y C HARRY BENEDICT Lake Linden, Mich DONALD H MCLAUCHLIN, San Fiancisco, Calif VICE PRESIDENT AND TREASURER ANDREW FLETCHER New York, N Y

Jan 1, 1952

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 1, 1950

By WALTER M. DAKE

GENERALY speaking, the bituminous coal mines of the country are being operated at a loss. To purchasers of the necessary commodity, a statement of this character may have the sound of a far fetched propagandist cry; but to the coal producer who lives in the hope of an up-turn in the almost stationary market price of his product, while inking in red his monthly operating balances, it carries the ringing sound of truth.

Jan 1, 1925

By D. B. Hobbs, L. W. Kempf, R. S. Archer

Silicon is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17s and 51s of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both 'normal" and "modified" sand castings. Review of Literature The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

By Willard P. Ward

HAVING been engaged during the past year in the manufacture of ferro-manganese in a blast furnace, I have imagined that some further information on this subject might be of interest to that large number of members of the Institute who are engaged in the iron and steel industries. The great question of the economical production of good steel, ingot metal, or homogeneous iron (we scarcely know now what to call it) from good materials, and at reasonable prices, has, thanks to the intelligence and energy of a few American engineers, been successfully solved in this country. Nearly all first-class railroads, and many that would riot rank so high, have adopted the Bessemer rail. Martin boiler-plates are rapidly gaining ground, in competition with

Jan 1, 1877

By Willard P. Ward

Having been engaged during the past year in the manufacture of ferro-manganese in a blast furnace, I have imagined that some further information on this subject might be of interest to that large number of members of the Institute who are engaged in the iron and steel industries. The great question of the economical production of good steel, ingot metal, or homogeneous iron (we scarcely know now what to call it) from good materials, and at reasonable prices, has, thanks to the intelligence and energy of a few American engineers, been successfully solved in this country. Nearly all first-class railroads, and many that would not rank so high, have adopted the Bessemer rail. Martin boiler-plates are rapidly gaining ground, in competition with

By T. Egleston

AT the Dover meeting of the Institute, Mr. F. A. Canfield showed some of the members a machine which he had invented for dressing mineralogical and geological specimens, which he has since modified and brought to such a high state of perfection, that after having used it for several months in preparing specimens for the cabinet of the

Jan 1, 1876

By T. Egleston

At the Dover meeting of the Institute, Mr. F. A. Canfield showed some of the members a machine which he had invented for dressing mineralogical and geological specimens, which he has since modified and brought to such a high state of perfection, that after having used it for several months in preparing specimens for the cabinet of the

By J. Chipman, G. G. Hatch

T. ROSENQVIST*—It is a pleasure to see the excellent way in which the experimental part of this work has been handled. There seems to be little doubt that the distribution data obtained corresponds most closely to thermodynamic equilibrium under the prevailing reducing conditions, namely equilibrium with graphite and one atmosphere CO pressure. The desulphurization curves in Fig 10 show the same general feature as the curves given by Holbrook and Joseph, but the distribution ratios are from 20 to 40 times greater—undoubtedly due to a closer approach to true equilibrium. In the theoretical discussion, the authors calculate a theoretical distribution (S) ration -jg-. which they find to be about 50 times greater than the experimental. The deviation is so great that the basis for their calculation needs a more thorough examination. The authors base their thermodynamic calculation on free energy expressions where diluted solutions of FeS and CaS are used as standard states. (The activity coefficient in diluted solutions is taken to equal unity.) Such a standard state will change when the nature of the solvent is changed. Taking the free energy of the reaction [FeS] ? (FeS), Eq 2, which is derived from the distribution of sulphur between an iron and a FeO-melt, it is very unlikely that the free energy of this reaction will be the same for a distribution between pig iron and a calcium silicate slag. Therefore a more fundamental basis for the thermodyuamic calculations seems needed, where all thermodynamic equations are referred to unambiguously defined standard states. The most natural standard states for CaO and CaS are the pure solid substances at the same temperature. As standard state for sulphur in iron, pure liquid FeS can be used. This rules out Eq 2 [FeS] ;=s (FeS) because ?F° = 0. The standard equation will then be: FeS, + CaO6 + Cgraph ?Fei + CaS8 + CO. vFo1773 = 25,000 cal It would be more universal and also simpler to refer the escaping tendency of sulphur in liquid iron to the corresponding H2S/H2 ratio which can readily be determined experimentally. As standard state a gas mixture H2S/H2 = 1/1 can be used. (This corresponds at the temperature of liquid iron closely to one atmosphere S2 vapor.) Thus the standard equation for the sulphur reaction can be formulated as follows: H2S0 + CaO3 + Cgraph ?H2o + CaS8 + COg The standard free energy of this reaction has been calculated from the best available data to AF°m3 = —35,000 cal. This gives for the equilibrium constant at 1500°C Now, the solubility of CaS in blast furnace slags has been determined by McCafferey and Oesterle* and corresponds at 1500°C to about 10 pet S (varying somewhat with the composition of the slag.) If the activity of CaS is assumed linear between 0-10 pet as curve 1, (see Fig 11), then acaO = 0.1 (S); (S) being wt. pet sulphur in the slag. For a diluted solution of sulphur in an iron melt saturated with carbon, the ratio H2S/H2 is, according to Kitchener, Bockris and Liberman,f about 0.01 [S], [S] being wt. pet sulphur in iron. Substituting these values in the expression for Kp we find The value 2.103 is only 4 times greater than the experimental coefficient found by Hatch and Chipman, but the value is very sensitive to a small error in AF°. A better agreement with the experimental distribution coefficient can be obtained if one assumes the activity of CaS to run like curve 2 (Fig 11). This (S) will give a lower theoretical W, value, a value which varies with (S) exactly as Hatch and Chipman learned. Such a shape of the activity curve, which corresponds to a positive deviation from Raoult's law, is actually to be expected from the fact that liquid silicate and sulphide phases usually show incomplete miscibility. A closer agreement between experimental and theoretical data can not be expected before we have more complete data for the individual activities of CaS and CaO in the slag. The activities acaS and Ocao referred to the solid phases as standard states, are exact defined quantities contrary to the somewhat undefined expression "free lime," and they are independent of any theory for the constitution of liquid slag. J. CHIPMAN (authors' reply)—The authors wish to thank Mr. Rosenqvist for his very interesting and useful thermodynamic addition. Curve 2 of his figure offers the needed basis for explaining the increase in the ratio (S)/[S] with increasing sulphur content. Attention is called to an error in the printed paper: Fig 2 and 3 are reversed. M. TENENBAUM*—In the figures showing the relationship between excess base and sulphur distribution (Fig 6, 7 and 9) the slope of the curve tapers off in the negative basicity range. Somewhat the same thing is observed with open hearth slags. In that case, the fact that some sulphur distribution between slag and metal is obtained with negative basicity is interpreted as indicating some dissociation of the lime silicate compounds whose existence in oxidizing basic slags has been used to explain various observed phenomena with regard to other slag-metal reactions. In the case of the blast furnace slags, the reduced slope of the sulphur distribution curve with decreasing excess base is attributed to the amphoteric effect of alumina. Has the possibility of other explanations been investigated ?

Jan 1, 1950

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.' This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

By A. M. Turkalo

IT is a well-known fact that martensitic steels show a greater resistance to brittle fracture than do pearlitic and bainitic steels. It was, therefore, thought worthwhile to investigate the mode of brittle fracture with respect to structure by studying the effect of various austenite decomposition products on the propagation of brittle fracture in steel by means of electron microscopy. Newly developed replication techniques together with the advantages of the electron microscope such as great depth of field, available high magnification and easy adaptation to stereophotography make electron microscopy very suitable for fracture studies. EXPERIMENTAL PROCEDURE An essentially plain carbon steel containing 0.56 pct C, 1.30 pct Mn, 0.02 pct P, 0.03 pct S and 0.22 pct Si was used in this investigation. The following table gives the heat treatments used to obtain the various austenite decomposition products: The resulting austenite grain size from the 870°C austenitization treatment was about an ASTM No. 7 grain size. The specimens which were 2 in. long, 1/4-in. diam bars were austenitized in a tube furnace through which argon gas was blown. The tube was not, however, air-free and the specimens were not completely oxide-free. Isothermal treatments were done in a lead bath. With the exception of the fully hardened specimen and the one as-isothermally transformed at 300°C the heat treated specimens were notched in the following fashion with a jeweler's saw. A cut about 0.08 in. deep was made perpendicular to the length of the bar. The specimen then was rotated about 45 deg and another cut about 0.08 in. deep was made. In the case of the hard martensitic and bainitic specimens, only one cut was made and the depth was not controlled. The design of the two-cut notch caused fracture to initiate at the point of intersection of the two saw cuts. The specimens were broken at -196°C in a Charpy impact testing machine. In order to hold the specimens securely in the impact machine two square pieces of mild steel were made about 5/8 in. long having the same cross section as that of a standard Charpy specimen but containing a hole 1/4 in. diam through the center of the cross-section. These adapters were slipped over the ends of the test specimen which was then secured tightly by means of set screws in the adapters. The specimen with the adapters was cooled to -196°C in liquid N,, then placed in the impact machine and broken within 3 sec. One half of the broken specimen was used for the electron microscope study of the actual fracture surface. The other half was nickel-plated and a cross section through the notch and fracture was polished for electron microscope examination. Carbon replicas of the fracture specimens for the electron microscope study were made essentially according to Bradley's evaporation technique.' Both direct carbon and two-stage carbon replication techniques were used. In the case of the direct carbon technique, a thin layer of carbon was evaporated first at an angle of about 45 deg to the mean fracture surface and then another film of carbon was evaporated normally to the fracture surface. The carbon replica was freed electrolytically.2 The specimen was made an anode in a 10 pct Nital polishing solution. It was etched intermittently by shutting off the power now and then. The freed replica was washed in 40 to 50 pct water solution of nitric acid for 10 min or so, then washed in water and picked up on a screen for examination. The two-stage carbon replication technique involved first making a primary replica of cellulose * acetate from which a carbon replica was then made. One side of a strip of cellulose acetate wet with acetone was pressed lightly against the surface of the specimen, allowed to dry and then stripped. Prior to the deposition of carbon, which was done at 90 deg to the cellulose acetate replica surface, chromium was evaporated at 45 deg. After the carbon evaporation the cellulose acetate was dissolved in acetone according to the Jaffe method3 leaving the carbon replica preshadowed with chromium for examination.

Jan 1, 1961

By A. Paul Bond

Two series of 17pct Cr iron-base alloys with small, controlled amounts of carbon and nitrogen were vacuum-melted in an effort to detertmine the meclz-uniswls of inter granulur corrosion in ferritic stain-less steels. An alloy containing 0.0095 pct N aid 0.002 pct C was very resistant to intergranular corrosion, even after sensitizing heat treatments at 1700" to 2100o F. However, alloys containing more than 0.022 pct Ni and more than 0.012 pct C were quite susceptible to intergranular corrosion after sensitizing heat treatments at temperatures higher than 1700°F. This corrosion was observed after the usual exposure tests and after potentiostatic polarization tests. Electronmicroscopic examination of the alloys susceptible to intergranular corvosion revealed a small grain boundary precipitate; this precipitate was absent in the alloys not susceptible to such corrosion. Thc electronmicrographs indicate that intergranu1ar corrosion of ferritic stainless steels is caused by the depletion of chromium in areas adjacent to precipi-tates of chromium carbide or chromium nitride. It also seems likely that the precipitates themselves are attacked at highly oxidizing potentials. Confirma-tion of the proposed mechanisms was obtained in tests on air-melted ferritic stainless steels containing titanium. The titanium additions greatly reduced susceptibility to intergranular corrosion at moderately oxidizing potentials but had no beneficial effect at highly oxidizing potentials. A major obstacle to the use of ferritic stainless steel has been their susceptibility to intergranular corrosion after welding or improper heat treatment. It appears that sensitization of ferritic stainless steel occurs under a wider range of conditions than for austenitic steels. In addition, a greater number of environments lead to damaging intergranular corrosion of sensitized ferritic stainless steels than to sensitized austenitic steels. The chromium depletion theory of intergranular corrosion is widely accepted for austenitic stainless steels'" although there: are some objections.3 On the other hand, several alternative mechanisms proposed for ferritic stainless steels include precipitation of easily corroded iron carbides at grain boundaries,' grain boundary precipitates that strain the metal lat-tice,5 and the formation of austenite at the grain bound-arie.6 The application of the chromium depletion theory to ferritic stainless steels has been discussed extensively by Baumel.7 The present investigation was undertaken to determine which of the proposed mechanisms can be sub- A PAUL BOND IS Research Group Leader, Climax Molybdenum Co of Michigan, Ann Arbor, Mich. stantiated with experimental data obtained on ferritic stainless steels. High-purity 17 pct Cr alloys containing small controlled additions of carbon or nitrogen were therefore prepared, and then examined electro-chemically and metallographically. EXPERIMENTAL PROCEDURES Materials. Two series of experimental alloys were prepared from electrolytic iron and low-carbon ferro-chromium using the split-heat technique. In this technique, the base composition is melted, and part of the melt is poured off to produce an ingot. To the balance of the melt, the required addition is made and the next ingot cast. This process is repeated until a series of the desired compositions is cast. By this procedure the impurity levels are essentially constant within each series. All the alloys in the carbon-containing series were melted and cast in vacuum. The base composition in the nitrogen series was melted and cast in vacuum; subsequent ingots in the series were melted with additions of high-nitrogen ferrochromium, and cast under argon at a pressure of 0.5 atmosphere. Two additional alloys were produced starting with normal purity materials. They were induction-melted while protected by an argon blanket and cast in air. Table I gives the composition of the alloys. The 2-in.-diam ingots produced were hot-forged and hot-rolled to a thickness of 0.3 in. and then cold-rolled to 0.15 in. All specimens were annealed at 1450°F for 1 hr. The indicated sensitizing heat treat-s s ments were performed on annealed material. All heat treatments were followed by a water quench. Specimen Preparation. For the 65 pct nitric acid test, 1 by 2 by 0.14-in. specimens were wet-surface ground to remove surface irregularities and polished through 3/0 dry metallographic paper. For the modified Strauss test, $ by 3 by 0.14-in. specinlens were similarly prepared. Immediately prior to testing, the Table I. Compositions of the Alloys Composition, pct Alloy Cr hio C N 270A 16.76 0.0021 0.0095 270B 16.74 0.0025 0.022 270C 16.87 0.0031 0.032 270D 16.71 0.0044 0.057 271A 16.81 0.012 0.0089 27 IB 16.76 0.018 0.0089 271C 16.69 0.027 0.0085 271D 16.81 0.061 0.0O71 4073' 18.45 1.97 0.034 0.045 4075† 18.5 2.0 0.03 0.03

Jan 1, 1970

By J. W. Putman, N. J. Grant, D. S. Bloom

SEVERAL recent determinations of the melting S point of pure chromium have been reported which give values of 1845°C1; 1895°C,² 1930°C,³ 1860°C,' and 1890°C.5 because of this wide spread of values, it appeared desirable to make one additional attempt to obtain a more accurate, reliable figure. bloom and Grantx recently reported a phase transformation in chromium:.--- it was desired to check this, too, in the course of checking the melting point. To accomplish this, a much higher purity chromium was required. Electrolytic chromium containing about 0.5 pct 0 was crushed to a finer size and was then annealed in highly purified, dried hydrogen at 1375°C for 100 hr. This treatment produced chromium with about 0.008 pct 0, 0.002 pct N, and negligible carbon. The balance of the impurities was 0.3 pct Fe, 0.03 pct Si, 0.004 pct S, and less than 0.001 pct Mo. This chromium was melted in a stabilized zirconia crucible under pre-purified argon, using induction heating. Temperature measurements were made with annealed wolfram-molybdenum thermocouples and a Leeds and Northrup Speedomax Recording Potentiometer. The thermocouples were annealed for 1 min in hydrogen at a temperature of about 2400°C. Each leg of the thermocouple was immersed in an ice-water mixture using mechanical connectors to the lead wires. The thermocouple tip was immersed in the molten chromium in a zirconia protection tube which introduces an error of about 3°C as a temperature drop through the walls of the tube. The weight of chromium was about 183 g. The dimensions of the melt in the crucible were about 1.25 in. diam x 2 in. high. The tip of the thermocouple was held about ½ in. from the bottom of the crucible. Two new thermocouples were used with the above set-up giving the results shown in Table I. Since this chromium is purer than that used by Greenaway, Johnstone and McQuillan,' by Carlile et al.,4 and other investigators,²,3 it is believed to be the more accurate. Thermocouple aging effects which are believed responsible for the high value of 1930°C³ were avoided in this work. This value of 1903°C is correct to about ±10°C. The right hand column lists the temperature of the a ? ß transformation on heating and the ß ? a on cooling.3 A sample curve is shown in Fig. 1. The value so determined is 1840°C + 15°C. Fig. 1 gives adequate evidence that there is a transformation in chromium at high temperatures.' References 'H. T. Greenaway, S. T. M. Johnstone, and M. K. McQuillan: High Temperature Thermal Analysis USing the Tungsten-Molybdenum Thermocouple. Journal Inst. Metals (November 1951) 19, p. 109. ²J. W. Putman, R. D. Potter, and N. J. Grant: The Ternary System Chromium-Molybdenum-Iron. Trans. A.S.M. (1951) 43, p. 824. ³D. S. Bloom and N. J. Grant: Chromium-Nickel Phase Diagram. Trans. AIME (1951) 191, p. 1009; Journal of Metals (November 1951). ' S. J. Carlile, J. W. Christian, and W. Hume-Rothery: The Equilibrium Diagram of the System Chromium-Manganese. Journal Inst. Metals (1949) 76, p. 169. 5G. Grube and R. Knabe: Ztsch. Elektrochemie (1936) 42, p. 793.

Jan 1, 1953

By P. L. Allsman

A method of analyzing blasting action indicates that major cost savings are possible by revising practice and bringing the classical blasting formulas up to date; difficult problems such as taconite and throw-breakup can be attacked by engineering Denonation pressure — the peak pressure developed by the explosive reaction; "shatter blasting." Average detonation pressure — the average pressure over the time the reaction continues; "heave blasting." Radial presswe — the stress in a radially expanding sphere about the detonation. Corresponds to the diminishing peak pressure. Lateral stress - the stress in a circumferential direction, induced by outward movement of the rock away from the detonation. Limiting stress or Slim— the rock property at which failure will occur in the case at hand; may be tensile or compressive strength, or combinations. Recent developments in explosives technology, following the advent of nuclear explosions, have led to a rather complete understanding of their action. A survey was made for the purpose of uncovering any knowledge which might be applicable in the mining and quarrying industries, the principal users of explosives. Although no revolutionary techniques have become apparent, much basic data pertaining to blasting — fortunately not classified — have been developed by recent research, from which a good general understanding of the process can be derived. It is hoped this explanation of the scientific principles governing explosive action, together with a proposed analysis of blasting practice, will further the development of mining engineering. NATURE OF THE REACTION: The phenomenon of explosion, termed detonation, is in reality a rather complex chemical reaction, and as such is completely explainable by physical and chemical laws. Detonation is characterized by high temperature and pressure, extreme rapidity — often being complete within one microsecond — and most importantly by formation of a shock pulse which accompanies the reaction zone. As with any chemical reaction, there is a critical value of temperature and pressure below which detonation can not occur; this is termed the "critical point". Whereas an explosive substance will decompose slowly at ordinary temperature, with the formation of gases which readily dissipate; at elevated temperature the reaction is considerably speeded. If pressure is suddenly applied at some point in an explosive medium, adiabatic compression results, and the temperature is locally raised. When the temperature becomes high enough the decomposition will be so rapid that the gaseous products do not have time to dissipate, but contribute to a further build-up of pressure. This, in turn, furthers adiabatic temperature rise over a widening area, and with any heat generated by an exothermic reaction, causes a rapid increase in temperature. Both temperature and pressure are spontaneously built up in this manner until the critical point is reached, resulting in detonation. The values of pressure and temperature necessary to create detonation are established by the unusual nature of the process. If temperature alone is raised above the critical point, without sufficient increase in pressure, deflagration or "low-order detonation" occurs. In the true, or "high-order detonation", the shock pulse resulting from the violent decomposition becomes an integral part of the reaction, and itself aids in increasing the detonation

Jan 1, 1961

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

By THOMAS S. MENNIE

ON GORE Mountain, about four and a half miles, southwest of the village of North Creek, Warren Co., N. Y., are the Barton Mines. Here is the largest known deposit of garnet in the world. This property is owned by H. H. Barton &: Son Co., of Philadelphia, and is being worked under lease by Barton Mines Corpn. North Creek is the terminus of the branch of the Delaware and Hudson R..R., which runs into the

Jan 1, 1925

By Francis J. Dennis

(San Francisco Meeting, October, 1911.) MANY factors govern the value of dredging-ground, and much capital can be wasted by the mistaken policy of contracting for the purchase of property and the installation of machinery before a thorough, examination has been made. To the uninitiated investor the presence of gold is generally the criterion,, and very superficial evidence is necessary to satisfy him as to this point. He considers the comprehensive report of a competent engineer as a wasteful extravagance and cannot understand why the engineer requires so much time and money to ascertain the information on which to base his conclusions, when the promoter can furnish him such pleasing and satisfactory data with but little expenditure of time and money. The uninitiated investor will often optimistically risk capital for purchase and equipment, and not until the venture comes to grief does he learn that the conditions are wholly unsuited for dredging. In many instances, a short preliminary examination by a competent engineer would have disclosed these facts. The mere presence of gold is by no means sufficient; some of the other factors necessary to be ascertained in determining the value of placer-ground for dredging-purposes are : (1) character and distribution of gold, and how much can economically be recovered; (2) character of bedding underlying the gravel, its contour, and whether its gold can be recovered by ordinary dredging-operations; (3) area and depths of gravel, surface contour, over-burden, water-level, proportion of fine material and boulders, and the presence of any material which might interfere with the dredging-operations and the recovery of the gold; (4) water-supply, power available, labor, transportation, and supplies, and cost of these ; (5) climatic condi-tions; (6) title to property, cost and royalties, and legal obstacles to carrying on dredging-operations. A brief reconnaissance may be sufficient to determine that some of the essential conditions for successful dredging are

Apr 1, 1912

By John E. Lanning

During the last decade, since most smelters have included Cottrell plants as standard equipment for the removal of dust from furnace gases, it has become apparent that smeltermen have had a new problem slowly developing. This problem has manifested itself in accelerated destruction of, or serious injury to, the masonry of flues and chimneys. The masonry either spalls, if the material is of low strength, or acquires large major cracks, either of which conditions attains such proportions that renewals or reinforcing become necessary to maintain the structure in satisfactory condition. This paper describes the failure of a large modern brick chimney to such an extent that its safety was vitally impaired; the investigation of its condition; the methods of restoring satisfactory strength to the structure; and the installation of an acidproof lining. Plant History The Clarkdale smelter of the United Verde Copper Co., which was put in operation in 1915, was primarily a blast-furnace plant. The smelter at Jerome had utilized blast furnaces exclusively, and in the design of the new (1915) plant, blast-furnace smelting evidently was considered of major importance, the smelting equipment consisting of four blast furnaces 48 in. by 26 ft. 8 in. and three reverberatories, each 19 by 101 ft. The latter, supplemented by roasters, were intended mainly for handling dust and fine ore resulting from the crushing operations. The original roasting equipment consisted of six six-hearth Wedge roasters, six more being added in 1917. All gases from blast furnaces, reverberatories, roasters and converters were conducted by means of suitable flues and dust chambers to one central chimney. This chimney, 30 ft. inside diameter by 400 ft. high, is a self-supporting steel structure, lined with 4-in. brick supported on steel shelf angles, riveted to the shell, spaced about 15 ft. vertically. The bricks were of local manufacture, not particularly hard-burned, and were laid in ordinary cement-fireclay-sand mortar. No record is available to indicate that any particular effort was made to secure an acidproof mortar. The same materials were employed in the construction of the reverberatory and roaster flues, and the roaster dust chamber. Parenthetically, it may

Jan 1, 1934