Search Documents

By A. R. Elsea, E. E. Fletcher

This paper describes a metallographic investigation of the influence of tungsten or molybdenum additions upon the transformation and precipitation reactions occurring in Co-rich Co-Cr alloys. It is shown that tungsten has little effect upon the a-ß transformation temperature range, while molybdenum tends to raise it. Both elements tend to promote the formation of ? phase, molybdenum being more potent in this respect than tungsten. HIGH temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed at an increasing rate during the past few years. This has resulted from the requirements in the design of modern aircraft engines. Although many alloys of this type are available, they have been developed on an empirical basis. Metallurgists do not have a clear understanding of the phases or structures that are responsible for these high temperature properties. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute with the object of learning more about the fundamental factors which promote high temperature strength in alloys. This study was to include a correlation of microstructure and the high temperature properties of Vitallium, an alloy which is widely used for high temperature service. Vitallium is a complex material both from the standpoint of composition and microstructure. Consequently, it was necessary to obtain informa- tion regarding the phase relationships in this alloy. The Co-Cr binary diagram was determined as the first phase of this investigation.' A second paper described the effects of iron, nickel, or nitrogen on the reactions occurring in the Co-rich end of this system.' The present paper covers a continuation of this investigation in which the effects of tungsten or molybdenum on the reactions occurring in Co-rich, Co-Cr-base alloys were determined. Preparation of 'rest Materials Two series of ternary Co-Cr-base alloys, representing Co-Cr ratios of 80:20 and 68:32 ( Cr x 100 =20 and 32 ) , were prepared containing ( Co + Cr = up to 6 pct W and up to 12 pct Mo. Melting stock consisted of electrolytic Co, electrolytic Cr, 99.9 pct pure W, and 99.9 pct pure Mo. Table I lists the chemical analyses of these materials. The melting furnace was a vertical porcelain tube

Jan 1, 1952

By J. J. Bodmer

IN 1855, Franz Uchatius patented, in England, his process of manufacturing cast steel. The first experiments, on a practical scale, were made at the Ebbw Vale Iron Works, Monmouthshire. The charge consisted of a mixture of cast iron with about 20 per cent. of a pure iron ore, and with or without other ingredients. In order to obtain the cast iron in a subdivided condition, Uchatius granulated molten pig-metal by running it into water, which during the operation was kept well agitated, and found that "the finer the iron is granulated, the softer will be the resulting steel." The writer is not aware that granulated iron has been used practically, otherwise than in the above-named process ; and until 1866 no other process of subdividing iron than by granulation was known. In April, 1866, an English patent was obtained by the writer for subdividing blast-furnace and other slags and metals in a molten condition, by passing the same through one or more pairs of rolls. In reference to iron the idea was, in following up the direction pointed out by the Uchatius process, to obtain better results in the puddling process by means of a thorough amalgamation (not simply a mixture) of the iron with the oxides and other ingredients in the charge itself. Experiments were made. A quantity of iron direct from the blast-furnace was subdivided (or laminated) by passing it through a pair of plain rolls. The rolls were hollow, and water was made to pass through them to keep them sufficiently cool. Without giving differential speed to the rolls, sheets were obtained about one-sixteenth inches thick, and from about one hundred square inches surface, downwards. With differential speed, the iron falls from the rolls in

Jan 1, 1874

By J. B. Austin

It is now well established, chiefly through the work of Davenport and Bain,' that the influence of temperature upon the rate of transformation of austenite to ferrite at constant temperature is represented by a curve of the type shown in Fig. 5 on page 295 and the reasons for this general shape have been discussed by them in a qualitative way. Thus, the upper part, or nose, of the curve is the resultant of two factors of which the rate of change with temperature is not the same, and by analogy with other like cases it is almost certain that these factors are: (1) the chemical potential, or driving force, of the transformation, which is zero at the equilibrium temperature and increases rapidly as the temperature falls below this point; and (2) a factor analogous to viscosity, or resistance of the crystal lattice to a change in structure, which also increases as the temperature is lowered. Just below the equilibrium temperature this virtual "viscosity" of the metal is relatively low—that is, the metal offers little resistance to a change in lattice—but the driving force is also small, and the net result is that the reaction proceeds slowly. As the temperature is lowered the magnitude of both factors increases; but at first the driving force increases more rapidly than the resistance and the reaction is observed to proceed more rapidly. At lower temperatures, however, the resistance begins to increase faster than the driving force, and eventually, at the nose of the curve, overbalances it, causing the reaction to proceed more and more slowly thereafter. This concept is somewhat, though not completely, analogous to that employed in certain electrical cases where the precise factors are known and are separately measurable. The current I (in amperes or coulombs per second) flowing through a given wire is proportional to the impressed potential, or driving force E, and is inversely proportional to the resistance R of the wire; that is, I = E/R. Stated in a slightly different way, the time required for one coulomb to pass a given point (1/I) is equal to R/E. If the temperature of the whole circuit is changed, the resultant change in 1/I will depend on the relative rates of change of R and of E,

Jan 1, 1935

By J. B. Austin

It is now well established, chiefly through the work of Davenport and Bain,' that the influence of temperature upon the rate of transformation of austenite to ferrite at constant temperature is represented by a curve of the type shown in Fig. 5 on page 295 and the reasons for this general shape have been discussed by them in a qualitative way. Thus, the upper part, or nose, of the curve is the resultant of two factors of which the rate of change with temperature is not the same, and by analogy with other like cases it is almost certain that these factors are: (1) the chemical potential, or driving force, of the transformation, which is zero at the equilibrium temperature and increases rapidly as the temperature falls below this point; and (2) a factor analogous to viscosity, or resistance of the crystal lattice to a change in structure, which also increases as the temperature is lowered. Just below the equilibrium temperature this virtual "viscosity" of the metal is relatively low—that is, the metal offers little resistance to a change in lattice—but the driving force is also small, and the net result is that the reaction proceeds slowly. As the temperature is lowered the magnitude of both factors increases; but at first the driving force increases more rapidly than the resistance and the reaction is observed to proceed more rapidly. At lower temperatures, however, the resistance begins to increase faster than the driving force, and eventually, at the nose of the curve, overbalances it, causing the reaction to proceed more and more slowly thereafter. This concept is somewhat, though not completely, analogous to that employed in certain electrical cases where the precise factors are known and are separately measurable. The current I (in amperes or coulombs per second) flowing through a given wire is proportional to the impressed potential, or driving force E, and is inversely proportional to the resistance R of the wire; that is, I = E/R. Stated in a slightly different way, the time required for one coulomb to pass a given point (1/I) is equal to R/E. If the temperature of the whole circuit is changed, the resultant change in 1/I will depend on the relative rates of change of R and of E,

Jan 1, 1935

By F. Bahnemann

IN discussing the problem of abnormal magnetic polarization, C. A. Heiland1? emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions.

Jan 1, 1935

By T. A. Rickard

The province of Otago consists, roughly speaking, of the southern half of the South Island* of New Zealand. On three sides it is washed by the Pacific Ocean and on the north it abuts against Westland and Canterbury. It covers an area of over 20,000 square miles, and for the most part has an extremely broken surface; the narrow plains of the sea-board are bounded by the rounded foothills which in turn are overlooked by range after range of the snowy summits whose varied beauty has made the island known as the Switzerland of the southern hemisphere. The gold-fields are confined to the quartzose schists which, in a broad band, 70 to 75 miles wide, cross the district, extending in a northwesterly direction from the shore of the western ocean into the northern provinces. These quartzose schists are the characteristic rocks of Otago, and to their curious structure are due the interesting differences exhibited by the mining districts in the modes of occurrence of the gold. These rocks, which are almost unbroken over their full extent, have been divided by the Provincial Geologist, F. W. Hutton, into two series of beds, named respectively the Wanaka and Kakanui formations. The only reason given for this division is the desire " to divide such an enormous thickness of rocks in order that the map might display somewhat of the geological structure of the district." As Hutton and others have pointed out, there is in fact no dividing line. The changes noticeable in the ascending series of schists are very gradual, and are due to the slowly decreasing effects of metamorphism. Hutton estimates the thickness of the Wanaka series at as much as 50,000 feet, and the

Jan 1, 1893

By D. H. Henley, F. F. Craig, W. W. Owens

The oil recovery performance of systems producing entirely by bottom-water encroachment has been experimentally determined in a series of scaled laboratory-model tests. The effects of well spacing, fluid mobilities, rate of production, capillary and gravity forces, well penetration and well completion techniques on the oil recovery performance have been investigated. The laboratory tests were performed using two uniform, un-consolidated sand-pack models. The models have ratios of the interwell distance to the formation thickness of 12 and 2, respectively. Tests at constant total fluid production rate were performed simulating a range of uniform reservoir characteristics and operating conditions encountered in field operations. The performance was determined by material balance and by observation of the encroachment of dyed fluids into the models. The results of the model tests agreed with those obtained mathematically when the conditions previously considered in theoretical studies were simulated, that is, when the oil and water are of equal density and no capillary forces exist. The model study of bottom-water drive indicated that certain variables can aoect the oil recovery performance to a greater degree than can be predicted by present analytical methods. In one comparison, the oil recovery at a water-oil ratio of 20 (obtained at a wide well spacing) varied as much as threefold, depending upon the system's properties and the production rate. Lesser effect of mobility ratio and no eflect of capillary forces over the range studied were observed. The test 'results also showed that the deeper the well penetration into the oil column, the greater the total water production to a producing WOR of 20. However, the ultimate sweep efficiency, and so the oil recovery to this level of WOR, did not vary significantly with well penetration. Horizontal fractures at the top of the formation did not significantly change the sweep characteristics of the reservoir models when values of radius and fracture capacity encountered in actual reservoirs were used. Impermeable pancakes at the bottom of the well moderately increased the oil recovery efficiency both at water breakthrough and at high water-oil ratios. A method is outlined by which the oil recovery performance of other uniform bottom-water drive systems can be estimated from the information obtained in these model tests. INTRODUCTION When oil is produced from a well which partially penetrates an oil zone completely underlain by water, the water rises directly beneath the well in a symmetrical cone when the system is uniform. Two different flow mechanisms can cause the water cone to form—coning and bottom-water drive. In coning, the aquifer is relatively inactive and the cone is formed beneath the well by the pressure gradients associated with the oil flow to the well. The oil can be produced by a solution-gas drive, an edge-water drive or other driving forces in the interwell area. In a bottom-water drive, the driving force for oil production comes from an upward encroachment of the underlying active aquifer. Two papers have analyzed the theoretical performance characteristics of bottom-water drive reservoirs. In the initial mathematical investigation, Muskat' established the equations which determine the pressure distribution in this type of reservoir and solved these equations for certain conditions. Specifically, it was assumed that the water and oil had equal mobilities and equal densities, there were no capillary forces, the pressure throughout the oil zone remained above the bubble-point pressure, a constant pressure existed at the initial water-oil contact and the oil was completely displaced by the encroaching water. These assumptions were used in obtaining analytical solutions. In general, Muskat found that the sweep efficiency to initial water breakthrough to the well was larger for the thicker oil zones, the closer well spacings, the lower ratios of vertical to horizontal permeabilities, the smaller the penetration of the well into the oil zone and the smaller the bore size of the well. The production history after water breakthrough was expressed as a volumetric sweep efficiency at a given producing water-oil ratio. The results indicated that cumulative oil production at producing water-oil ratios of 10 is less affected by the well spacing than is the water-free production history. Muskat studied well spacing which today would be regarded as close. The maximum value of his dimensionless well spacing (ratio of interwell distance to formation thickness) was 4.3. This would require the development of a 50-ft-thick oil sand on less than 10-acre spacing if the vertical and horizontal permeabilities were equal, with

By Charles Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metal-lography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method f compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform with-out fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orienta-tions resulting from recrystallization and is being extended to other metals and other types of deformation.

Jan 1, 1938

By E. J. Yoder, N. B. Aughenbaugh, R. B. Johnson

Mineral aggregates experience degradation during field and laboratory compaction. Reduction in the aggregate size is accomplished by abrasion of the particle edges and fracturing of individual pieces which have become overstressed. Little is known of the factors that govern the amount of breakdown experienced for a given situation. A field study was made of the factors affecting aggregate breakdown under compaction using three carbonate aggregates of different physical properties. The preliminary results indicate that rock type, compactive effort, gradation, and thickness of compactive layer are factors which exert the greatest influence. Mineral aggregates experience a mechanical breakdown of some of the aggregate pieces into smaller fragments during any compaction process, whether in the field or laboratory. This phenomenon occurs as abrasion of the sharp edges during movement and reorientation of the particles in densifying and/or as granulation and fracturing of those pieces which have become overstressed. Two types of aggregate breakdown occur in the field. These may be classed in a general category of aggregate degradation.* One occurs during the con- * Aggregate degradation has been defined in many different ways. For this paper it is considered as any breakdown of larger particles into smaller ones, whether mechanical or chemical. struction period and is related to the densification of the aggregate body from a loose state to a relatively dense mass by heavy compaction equipment. This type is almost entirely a mechanical action. The other occurs after the construction period when the roadway has been put into use. This in-service breakdown is; a different phenomenon from the breakdown during construction in the sense that it combines mechanical with chemical changes. Time becomes an important consideration that may cause subordinate factors in construction degradation to develop into principal ones for in-service breakdown. Breakdown of aggregates in service has been extensively studied by investigators from the northwestern

Jan 1, 1962

By W. G. Pfann

In zone-melting, a small molten zone or zones traverse a long charge of alloy or impure metal. Consequences of this manner of freezing are examined with impurerespect to solute distribution in the ingot, with particular reference to purification and to prevention of segregation. Results are expressed in terms of the number, size, and direction of travel of the zones, the initial intermsofsolute distribution, and the distribution coefficient. IF a charge of binary solid-solution alloy is melted and then frozen slowly from one end, as for example in the Bridgman method of making single crystals,' coring usually occurs, with a resulting end-to-end variation in concentration. Such coring, or normal segregation, is undesirable where uniformity is an object. On the other hand, for certain systems, it can be utilized to refine a material by concentrating impurities at one end of the ingot.'. ' In the present paper a different manner of freezing will be examined with respect to the distribution of solute in the ingot. A number of procedures will be indicated which have in common the traversal of a relatively long charge of solid alloy by a small molten zone. Such methods will be denoted by the general term zone-,melting, while the process described in the preceding paragraph will be called normal freezing. It will be shown that, in contrast to normal freezing, zone-melting affords wide latitude in possible distributions of solute. Segregation can either be almost entirely eliminated or it can be enhanced so as to provide a high degree of sttparation of solute and solvent. A number of simplifying assumptions will be invoked which, while not entirely realizable in practice, nevertheless provide a suitable point of departure for more refined treatments. Moreover, our own experience with zone-melting has shown that, for certain systems at least, the analysis holds quite well. The present paper will be confined to a discussion of principles and a general description of procedures. Comparison with experiment is planned for later publication. Normal Freezing Before considering zone-melting, segregation during normal freezing will be reviewed briefly. If a cylinder of molten binary alloy is made to freeze from one end as in Fig. 1, there usually will be a segregating action which will concentrate the solute in one or the other end of the ingot. If the constitutional diagram for the system is like that of Fig. 2, then the distribution coefficient k, defined as the ratio of the concentration in the solid to that in the liquid at equilibrium, will be less than one and the solute will be concentrated in the last regions to freeze. If the solute raises the freezing point, then k will be greater than one and the solute will be concentrated in the first regions to freeze. The concentration in the solid as a function of g, the fraction which has solidified, can be expressed by the relation: C = kC0 (1-g)k-1 [I] where C, is the initial solute concentration in the melt. Eq 1 is based on the following assumptions: 1—Diffusion in the solid is negligible. 2—Diffusion in the liquid is complete (i.e., concentration in the liquid is uniform). 3—k is constant. Concentration curves representing eq 1 for k's from 0.01 to 5.0 are plotted in Fig. 3. This equation, in one form or another, has been treated by Gulliver,³ Scheuer,4 Hayes and Chipman5 for alloys and by McFee2 for NaCl crystals. It is derived in Appendix I. It should be pointed out that the k which is calculated from the phase diagram will be valid only in the ideal case for which the stated assumptions are correct. In all actual cases, the effective k will be larger than this value for solutes which lower the melting point, smaller for solutes which raise the melting point, and will probably vary during the beginning of the freezing process. For simplification it will be assumed that the ideal k is valid. Zone-Leveling Processes The processes of this part are designed to produce a uniform, or level, distribution of solute in the ingot. Single Pass: Consider a rod or charge of alloy whose cross-section is constant and whose composition, C2, is constant, although permissibly varying on a microscopic scale." Such a charge might be a rapidly frozen casting or a mixture of crushed or powdered constituents. Cause a molten zone of

Jan 1, 1953

By R. G. Powell, R. Schuhmann, E. J. Michal

Liquidus surfaces in the ternary system FeO-Fe2O3-SiO2, were determined from 1250' to 1450°C by the procedure of equilibrating small samples in platinum crucibles, quenching, and microscopic examination. The experimental results were combined with previously published information to construct a ternary diagram for the system showing the entire temperature-composition range of stability of iron silicate slags. Metallurgical applications of the diagram, especially in copper smelting, are discussed briefly. IRON oxides are almost unique among the common oxide constituents of metallurgical slags in that the iron occurs in two different states of oxidation, ferrous and ferric. Moreover, in liquid slags the degree of oxidation of the iron is readily changed by reactions of the slags with oxidizing agents or reducing agents. This behavior of iron oxides in slags accounts, for example, for the effective transfer of large quantities of oxygen through slag layers in open hearth steelmaking. In this process, oxygen supplied by reactions at the gas-slag interface is dissolved in the slag with the oxidation of ferrous iron to ferric. Ferric oxide is transported across the slag layer by convection, and at the slag-metal interface the oxygen reacts with liquid metal while the ferric iron is reduced back to the ferrous state. Another group of processes in which variation in degree of oxidation of iron has great practical importance is in copper smelting. In matte smelting and converting, such large proportions of the iron are oxidized to the ferric state that problems are encountered in preventing or controlling the formation of solid magnetite. The ferrous-ferric relationship also affects the attack of iron oxides on high-SiO2 refractories, which appears to be most severe under reducing conditions for which ferrous iron predominates. Darken and Gurry' determined the chemical properties and phase equilibria of pure iron oxide slags. Their data show that iron oxide melts can have compositions ranging almost all the way from FeO to Fe2O3. The melts of lowest oxygen contents, which exist in equilibrium with metallic iron, approach ferrous oxide in composition but still have a small percentage of ferric oxide. The melts of highest oxygen contents, which have oxygen dissociation pressures of 1 atm, are above magnetite in oxygen content, with over two-thirds of the iron in the ferric state. The previously established phase diagrams for silicate slag systems all show FeO as the iron oxide component. However, Bowen and Schairer? who determined the FeO-SiO2 diagram and many of the other diagrams used by slag chemists, have been careful to point out that their systems always contained both ferrous and ferric iron. Thus, their data are for limiting mixtures with minimum contents of ferric iron, obtained by melting and equilibration in iron crucibles. Under these conditions, the Fe2O3 percentages found by analysis were small enough to justify simplification of the published phase diagrams by calculating the Fe2O3 to equivalent FeO and ignoring Fe2O3 as an additional component. On the basis of experimental measurements of melting points of iron oxides on silica in the presence of various gas mixtures, Darken3 worked out phase diagrams for the Fe-Si-0 system which show the important phase equilibria in terms of temperature and gas composition. This study clarified many aspects of the application of the phase rule to the FeO-Fe2Oa-SiO2 system and was an important basing

Jan 1, 1954

By D. L. Albright, R. W. Kraft

A technique is described whereby the study of crystal perfection through the use of conventional X-ray rockite curves is extended to three dimerzsions. Specinzens of unidirectionally solidified eutec-tic alloy which consist of a nearly perfect parallel arrangement of alternating Platelets of Al and CuAl2, but which contain lamellar faults have been analyzed by this technique in conjunction with X-ray microscopy. Analysis of the data has shown that some rotational symmetry about the growth direction occurs, that small groups of lamellae between faults diffract as a unit, and that the misorientation caused by a fault is on the order of a degree of arc. A eutectic-grain can be defined as that portion of a eutectic specimen in which the crystallographic orientation of each phase AND the microscopic or met-allographic orientation of the phase particles have fixed angular relationships one to another. Eutectic-grains of the A1-CuA12 eutectic, which is a normal lamellar eutectic, have been grown by unidirectional solidification and identified as such.1-3 To a first approximation, a eutectic-grain in this system consists of two interpenetrating single crystals which are related to each other and to the lamellae themselves as follows:

Jan 1, 1962

By M. King Hubbert, David G. Willis

A theoretical examination of the fracturing of rocks by means of pressure applied in boreholes leads to the conclusion that, regardless of whether the fracturing fluid be of the penetrating or non-penetrating type, the fractures produced should be approximately perpendicular to the axis of least stress. The general state of stress underground is that in which the three principal stresses are unequal. For tectonically relaxed areas characterized by normal faulting, the least stress should be horizontal; the fractures produced should be vertical with the injection pressure less than that of the overburden. In areas of active tectonic compression, the least stress should be vertical and equal to the pressure of the overburden; the fractures should be horizontal with injection pressures equal to or greater than the pressure of the overburden. Horizontal fractures cannot be produced by hydraulic pressures less than the total pressure of the overburden. These conclusions are compatible with field experience in fracturing and with the results of laboratory experimentation. INTRODUCTION The hydraulic-fracturing technique of well stimulation is one of the major developments in petroleum engineering of the last decade. The technique was introduced to the petroleum industry in a paper by J. B. Clark,' of the Stanolind Oil and Gas Co. in 1948, and since then its use has progressively expanded so that by the end of 1955 more than 100,000 individual treatments had been performed. The technique itself is mechanically related to three other phenomena concerning which ah extensive literature had previously developed. These are: (1) pressure parting in water injection wells in secondary-recovery operations, (2) lost circulation during drilling, and (3) the breakdown of formations during squeeze-cementing operations, all of which appear to involve the formation of open fractures by pressure applied in a wellbore. The most popular interpretation of this mechanism has been that the pressure had parted the formation along a bedding plane and lifted the overburden, notwithstanding the fact that in the great majority of cases where pressures were known they were significantly less than those due to the total weight of the overburden as determined from its density. Prior to 1948, this prevalent opinion had already been queried by Dickey and Andresen,2 in a study of pressure parting; and by Walker,"' who, in studies of squeeze cementing, pointed out that the pressures required were mostly less than those of the overburden, and inferred that the fractures should be vertical. J. B. Clark,' in his paper introducing hydraulic fracturing, and later Howard and Fast," and Scott, Bearden, and Howard," also of Stanolind, postulated that the entire weight of the overburden need not be lifted in producing horizontal fractures, but that it was only necessary to- lift an "effective overburden," requiring a correspondingly lower pressure. Hubbert,7 in discussing the paper by Scott and associates, pointed out that the normal state of stress underground is one of unequal principal stresses; and in tectonically relaxed areas, characterized by normal faults, the least stress should be horizontal. Therefore, in most cases, fracturing should be possible with pressure less than that of the overburden and, moreover, such fractures should be vertical. Harrison, Kieschnick, and McGuire,8 also on the expectation that the least principal stress should be horizontal, argued strongly in favor of vertical fracturing. Scott, Bearden, and Howard6 observed that, when

Jan 1, 1958

By N. I. Fisher, J. Shepherd

Abstract-Statistical studies have been carried out on structural geological data collected across a large zone of roof failure 600 m (1968 ft) wide and at least 800 m (2642 ft) long in the Greta coal seam at Aberdare East Colliery. Two swarms of hundreds 2 of minor, normal faults with throws commonly between 3 and 300 mm in the room and pillar workings are broadly coincident with roof failure. The faults have been classified into dip slip and oblique and strike slip types. Roof conditions have been classified into good; troublesome with subclasses scaly, heavy, gutter falls and wide, flat-roofed falls; and severely failed with subclasses very heavy roof, gutter falls and dome falls. Troublesome conditions are defined as those in which the height of the fall is less than or equal to 0.3 m, and severely failed conditions as those in which the fall height is greater than 0.3 m. Comparison of faults, roof conditions and mining rate on a shift basis indicates that faults and roof failure are much more important than machine breakdowns in reducing mining rate. The effect of faults on roof conditions has been quantified using a concept called the "zone of influence, " a rectangular area around a fault in which the fault has potentially deleterious effects. The spatial comparison of fault "zones of influence" with areas of roof failure using Spearman's rank correlation coefficient shows that, while normal dip slip faults do not appear to be associated with roof failure, oblique slip and strike slip faults appear to be associated with roof classed as severely failed. The "zone of influence" of an oblique slip fault may extend up to 3 m on each side of it in the headings and up to 1.14 m in the cut-throughs. The fault "zone of influence" has geomechanical implications for the design of mine openings and possibly represents the maximum length of a cantilevered roof beam likely to fail during mining, owing to a fault. Roof conditions could possibly be predicted in blocks of virgin coal if the type of fault could be identified in oriented drill cores.

Jan 9, 1978

By C. E. McCarthy, A. George Stern, Stanley J. Green

THE national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of I9I4-I8 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. WYOMINGITE DEPOSIT For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the southwestern part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, I2; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the wyomingite has a potash content averaging slightly higher than eleven per cent K20. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1944

THE only asbestos mine in the Middle East is on the Island of Cyprus, high in the Trodos Mountain village of Amiandos. The mine is owned by the Tunnel Asbestos Cement Co. Annual output is some 18.000 tons of short fibre in the 4-T. 4-Z, and 5-R grades.

Jan 9, 1953

By C. E. McCarthy, A. George Stern, Stanley J. Green

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By A. George Stern, Stanley J. Green, C. E. McCarthy

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By Maurice L. Pinel, Thomas Wright, Thomas T. Read

The erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1, ll, l² but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until morc and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: I. 502 A.D. A pair [right and left) of recumbent lions (Fig. 1). Base 7¼ by 113/8 in., height over-all 5½in, weight 26 Ib. each. The tranblation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third pear of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938

By Maurice L. Pinel, Thomas Wright, Thomas T. Read

The erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1, ll, l² but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until morc and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: I. 502 A.D. A pair [right and left) of recumbent lions (Fig. 1). Base 7¼ by 113/8 in., height over-all 5½in, weight 26 Ib. each. The tranblation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third pear of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938