Search Documents

By K. Torssell, U. Lindborg

The kinetics of precipitation deoxidation is considered from a theoretical point of view. The size distribution and the total content of deoxidation products are estimated statistically as a function of time, taking into account Stokes and gradient collisions between the particles and separation at the top surface of the bath. The assumption is made that two particles coalesce into one larger particle as a result of a collision. General expressions are derived and calculations are carried out numerically for the case of silica particles in liquid iron. The analysis predicts a three-stage behavior for the removal of oxygen, an incubation stage, a stage of rapid separation, and a slow final stage where the content approaches the equilibrium value. The agreement with experimentally determined size distributions and deoxidation times is considered to be good. A quantitative estimation of such growth mechanisms as diffusion from the melt and redistribution of oxygen from small particles to large ones shows that these latter mechanisms cannot explain the experimentally observed gvowth of inclusions. This also indicates that collisions provide the important growth mechanism. OXIDE inclusions precipitate when a deoxidizer like silicon or aluminum is added to a steel bath. The inclusions grow and the large particles tend to separate from the bath. For each type of oxide the growth determines the sizes of the final inclusions as well as the total inclusion content of the steel. The mechanism of growth is controversial, however. It has been suggested that an inclusion grows principally by diffusion of atoms through the melt to the inclusion particle or principally by collisions and coalescence with other inclusions. Diffusion growth is always present to some extent but recent experiments and calculations by Torssell,' Kniippel et 'a1.,2 Sano et al. and Miya-shita4 indicate that collisions may be more important than previously realized. A detailed analysis has so far been lacking. The present paper is a quantitative, statistical analysis of the growth and separation of inclusions and is based on a collision theory. Nuclea-tion is not considered. The numerical estimates are based on the experimental conditions of Torssell's' investigation and comparisons are made with his observations. Torssell' studied the growth and separation of silica particles in liquid iron. Samples were taken from a 0.6 kg iron bath at various times after the addition of silicon. By a particle-counting technique developed by Bergh and Lindber~the size distribution of the inclu- sions was determined. The number of particles at the first sampling, 10 sec after silicon addition, was of the order of 3 x lo7 to 10' per cu cm, the largest particles having a radius of 2 to 4 pm. The volume fraction was 0.001 to 0.004; i.e., the dispersion was very dilute. During subsequent holding the largest particles increased their radius by a factor of 10 after about a minute, and the whole size distribution was displaced toward larger values. These results were obtained with allowance for precipitation of the equilibrium concentration of oxygen during solidification. The bath contained less than 0.01 pct of C. Figs. 1 and 2 show the typical appearance of the inclusions. Most particles are very closely spherical and appear to have been liquid or semiliquid in the melt. The observed number of inclusions, about 5x 10' per cu cm, is of the same order of magnitude as found by ~er~h.' This is a large value. It follows that the diffusion distances are very short and that the precipitation

Jan 1, 1969

By C. O. Fairchild

THE meaning of temperature control can be extended to cover not only the control of temperatures' but also the control of processes through a knowledge of the temperatures involved. In this sense it has a very wide interest. A list of the industries in which temperature control is used in one way or another would cover nearly the entire industrial field. This discussion will be confined to the field of high temperatures. In practically all industries involving operations at high temperatures, pyrometers are used or men are paid for their ability either to estimate temperatures or gage an operation by some physical or chemical change or condition dependent on temperatures. As progress is made in the development of instruments and of methods for measuring temperature, some of these highly skilled artisans are learning the use of a new tool. Many processes have been, in recent years, improved by means of exact measurement thus substituted for estimation, but in a great many industries the pyrometer has had practically no opportunity to demonstrate its usefulness. The perfecting of instruments must be accompanied with a dissemination of the knowledge that new instruments are available and can be economically used. The demand at present, however, is ahead of the supply, and many industries are handicapped by the want of pyrometers. One of the highest paid skilled tradesmen of the present time is the man in the steel rolling mill who knows when proper working temperatures are attained. The metallurgist in his development of steels is continually demanding closer adherence to given temperature ranges in the processes, and the pyrometer is rapidly becoming indispensable. Properties of the finished products are being correlated with working temperatures and so closely that in some cases even the pyrometer is taxed to give the required accuracy. The greatest progress has been made in those industries in which the lower temperatures are used, particularly below 500° C. In this lower range automatic control has been highly developed.

Jan 9, 1919

By Stanley W. Sundeen

2.3-1. Introduction. The subject-"Preliminary Evaluation of Coal, Metallic and Industrial Mineral Deposits for Surface Mining'-seems at first glance to be definitive and not likely to be misinterpreted. Nevertheless, there are widely divergent opinions as to what is meant by "preliminary" and even as to what is meant by "evaluation." Some definition and qualification is necessary in order to provide a readily recognized basis for discussion. Evaluation evokes the idea of organizing extant data and judging its significance especially in the economic sense. It also may evoke the concept of the physical processes of acquiring the data that will characterize the deposit such as the geologic mapping, drilling, etc. Castle (5) considers that evaluation may embrace psychological aspects wherein human traits as, for example, over optimism might cause the evaluator to overlook obvious project weaknesses. In this chapter, evaluation is discussed primarily from the viewpoint of economically appraising a project from data available at a given point in time. The qualifying adjective "preliminary" is not easily defineable. In fact, some kind of evaluation proceeds, if not continuously, intermittently over the full span of exploration and early stages of development of a deposit. Bailly (1) comments: "Sometimes, before starting exploration in new areas or countries for a given commodity, we establish models to define what minimum combinations of re- coverable grade and tonnage are needed to give the minimum acceptable rate of return established by corporate policy. Then, before starting physical exploration in any target area we try and guesstimate optimistically what best 'geometry-grade-tonnage' can be expected. If these are acceptable in light of above minimum combinations, exploration is started as soon as funds are appropriated for the target area.''

Jan 1, 1968

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By A. B. Parsons

PUBLICATION of this little volume is a luxury that the Institute itself could scarcely afford. In truth, no engineer nor geologist, no assayer nor metallurgist would be likely to enhance his knowledge, improve his technique, or cut his own operating costs by reading this excellent translation of two booklets first published circa A.D. 1520. It is doubtful if the present enterprise would, in a practical or tangible way, "promote the arts and sciences connected with the economic production of the useful minerals and metals." And such, is the prescribed purpose for which the funds of the Institute should be spent. Fortunately for the Institute, the Seeley W. Mudd Memorial Fund is not so circumscribed; and the Fund Committee enjoys, greater liberty of action. The sponsorship by the Mudd Fund in 1942 of the publication of The Pirotechnia of Vannoccio Biringuccio, as translated by Dr. Smith and Mrs. Gnudi, was an innovation-indeed something of an experiment. Not only was the content of the volume significant mainly for its "cultural" and "scholarly" attributes; -but the format, an outstanding example of the fascinating art of bookmaking, bore no resemblance to the ordinary technical book. The Committee, frankly, was surprised at the enthusiastic reception accorded the volume. When a second edition was required, the Committee became convinced that the publication of material of this type, particularly if printed and bound in attractive form, was an appropriate avenue for utilizing a moderate proportion of the monies available from the Fund. The Bergbüchlein and the Probierbüchlein antedate by some years the first publication of De la Pirotechnia and of De re Metallica; but Georgius Agricola, the author of the latter work, made good use of the material in the earlier volumes. As pointed out in the Introduction, both

Jan 1, 1949

By T. V. Subrahmanyam, A. P. Rao

The adsorption behavior of chalcopyrite has been studied at different xanthate concentrations and flow rates in a column apparatus with potassium ethyl xanthate as the collector. Based upon the experiment results an equation of the type: 1/F = K3 + m3C + k2/t.Cm2.fm1 is proposed to account for the experimental data. Among copper minerals an early study on chalcocite by Gaudin and Schuman (Taggart, 1951) is well known for its research on the kinetics of the reaction by conventional method of mass balance between the products of reaction and xanthate consumed. The results were interpreted by the concept of ion exchange adsorption. Szeglowski (1977) conducted measurements on the adsorption of potassium ethyl xanthate on copper polarized to various potentials, the adsorption being measured by radio-tracer techniques. The adsorption in the range -1800 to 700 mv was found to be a reversible physical adsorption. The potential range in which the primary electrode process could lead to surface coverage with a minimum number of product layers was evaluated. The adsorption density of xanthate on sulfide surface was found to be related to the concentration of xanthate in solution and concentration of depressants as: [ ]

Jan 1, 1983

By G. Rowan, M. W. Clegg

The basic equations for the flow of gases, compressible liquids and incompressible liquids are derived and the full implications of linearising then discussed. Approximate solutions of these equations are obtained by introducing the concept of a disturbed zone around the well, which expands outwards into the reservoir as fluid is produced. Many important and well-established results are deduced in terms of simple functions rather than the infinite series, or numerical solutions normally associated with these problems. The wide range of application of this approach to transient radial flow problems is illustrated with many examples including: gravity drainage of depletion-type reservoirs; multiple well systems; well interference. INTRODUCTION A large number of problems concerning the flow of fluids in oil reservoirs have been solved by both analytical and numerical methods but in almost all cases these solutions have some disadvantages — the analytical ones usually involve rather complex functions (infinite series or infinite integrals) which are difficult to handle, and the numerical ones tend to mask the physical principles underlying the problem. It would seem appropriate, therefore, to try to find approximate analytical solutions to these problems without introducing any further appreciable errors, so that the physical nature of the problem is retained and solutions of comparable accuracy are obtained. One class of problems will be considered in this paper, namely, transient radial flow problems, and it will be shown that approximate analytical solutions of the equations governing radial flow can be obtained, and that these solutions yield comparable results to those calculated numerically and those obtained from "exact" solutions. It will also be shown that the restrictions imposed upon the dependent variable (pressure) are just those which have to be assumed in deriving the usual diffusion-type equations. The method was originally suggested by Guseinov,1 who (a) postulated a disturbed zone in the reservoir, the radius of which increases with time, and (b) replaced the time derivatives in the basic differential equation by its mean value in the disturbed zone. In this paper it is proposed to review the basic theory leading to the equations governing the flow of homogeneous fluids in porous media and to consider the full implications of the approximation introduced in linearising them. The Guseinov-type approximation will then be applied to these equations and the solutions for the flow of compressible and incompressible fluids, and gases in bounded and infinite reservoirs obtained. As an example of the application of this type of approximation, solutions to such problems as production from stratified reservoirs, radial permeability discontinuities; multiple-well systems, and well interference will be given. These solutions agree with many other published results, and in some cases they may be extended to more complex problems without the computational difficulties experienced by other authors. THEORY In order to review the basic theory from a fairly general standpoint it is proposed to limit the idealising assumptions to the minimum necessary for analytical convenience. The assumptions to be made are the following: 1. That the flow is irrotational. 2. That the formation is of constant thickness. 3. Darcy's Law is valid. 4. The formation is saturated with a single homogeneous fluid.

A HIGHLY successful joint conference on coal-mine transportation was held at Pittsburgh on Oct. 20 by the Pittsburgh Section of the American Insti-tute of Mining and Metallurgical Engineers and Mining Section of the Engineers' Society of Western Pennsyl-vania. C. E. Lesher, executive vice-president of the Pittsburgh Coal Co., presided over 215 members and others in the morning and Graham Bright, sales en-gineer with the Mine Safety Appliances Co., presided over about 180 in the afternoon. There were four prepared papers and much discussion, as well as a good luncheon between the sessions. Mechanical loading in the Pittsburgh district was discussed by L. E. Young, production vice-president of the Pittsburgh Coal Co. More companies in this district are using loading machines, more types of machines are being tried, and more coal is being mined by them than heretofore. The draw-slate above the Pittsburgh seam is the main problem; but devices for supporting and moving draw-slate are being tested. Except in two mines, the slate is being taken down. The fundamentals of the machines are similar, but the electrical drive and other parts have been improved. The problem is to recover or move as much coal as possible without hand labor. Methods of cleaning coal must be improved to meet the new methods of loading. The Pittsburgh Coal Co. has ten Joy machines and others are under order, a Myers-Whaley machine, Jeffrey conveyors, and Eichoff conveyors. The last mentioned are used in entries and other conveyors in rooms. At Montour No. 10 mine, one Joy machine is worked in rooms and one in entries.

Jan 12, 1927

By John L. Boardman

BECAUSE of the attention that has re¬cently been given to the health and safety of miners by various organizations such as the A.I.M.E., The American Congress, Mining Section, National Safety Council, as well as the Bureau of Mines and various state mining departments, your committee on health and safety deemed it best to call attention this year to the mine-accident cause that is by far the most important; namely, injuries due to falls of ground, rock, roof and coal. Each of several members of the committee contributed a brief outline of the importance of this accident cause in his district. While these papers were brief, it would require too much time and space to give them in full, therefore we present an outline of each and summation of all. REPORT OF M. D. COOPER, HILLMAN COAL AND COKE CO. M. D. Cooper, Division superintendent, Hillman Coal and Coke Co., Pittsburgh, Pa., contributed the following: During the period from 1930 to 1939, accidents from falls of roof in bituminous mines average 54.3 per cent of all accidents. In mechanized mining, there is a tendency toward reduction in this class of accidents because the operator of the machine is usually at a distance of 10 to 20 ft. from the face, whereas. in hand loading the miner is close to the face during most of the shift. No doubt the use of aluminum and light steel beams supported at regular intervals by jacks, a common practice in mechanical mining, has contributed to the favorable record so far developed. REPORT OF M. H. FIES, DE BARDELEBEN COAL CORPORATION Milton H. Fies, Vice-President, DeBardeleben Coal Corporation, Birmingham, Ala., says: With reference to the types of mining, it is suggested that a clear understanding be had as to the character and thickness of the directly overlying strata, with especial consideration to the strength and in some cases an analysis of it. In coal mining, generally speaking, overlying strata higher in silica than others is stronger. In changing from narrow to wide places, the procedure should be experimental, both as to the width and depth of places and as to the nature of the necessary timbering. Since most of the accidents in coal mining particularly are due to falls of roof and coal, this phase of mining should be attacked with vigor. There is no substitute for discipline and, in this connection, under present conditions it is important that cooperation by the labor organizations be sought and that a spirit of fairness prevail. Frequent and thorough inspection of all active working places should be made.

Jan 1, 1941

By I. E. Campbell, R. I. Jaffe

Oxygen, nitrogen, and hydrogen are known to be absorbed by titanium at elevated temperatures. Ehrlichl reports that about 30 at. pct oxygen can be dissolved in solid solution by alpha-titanium. Nitrogen also has a solid solubility in alpha-titanium, but there is no information as to its extent. The solid solubility of hydrogen in titanium also is high. Kirshfeld and Sieverts2 report 50 at. pct soluble, while Hägg3 reports about 33 at. pct hydrogen to be soluble in alpha-titanium. General statements are made in the literature that oxygen, nitrogen, and hydrogen embrittle titanium, but no quantitative measurements have been made of the effect of these gases on the mechanical properties of the metal. One reason for this is the lack of a source of titanium pure enough to be considered a suitable starting material. Iodide-refined titanium, made by thermal decomposition of titanium iodide vapor on an incandescent wire,4 contains small amounts of carbon, silicon, iron, and aluminum, but is very low in oxygen, nitrogen, and hydrogen content, and, therefore, was used in this work. A further reason for the lack of quantitative information on the effect of these gases, particularly oxygen, is the difficulty of carrying out accurate analytical determinations at the low concentrations of interest in this work. For this reason, the oxygen, nitrogen, and hydrogen were added in measured amounts as gases, and diffused into the titanium, to avoid the necessity of chemical analysis. The purpose of the work reported here was to isolate and measure the effects of oxygen, nitrogen, and hydrogen on titanium of the highest purity available at the time. The concentrations studied were 0.25, 0.5, and 1 at. pct in each case. Experimental Work One-half of a 24-in. hairpin of iodide-refined titanium was available for this work. The rod was approximately 0.25-in. in diam and had a 0.003-in.tung sten core. From chemical and spectro-graphic analyses, the purity of the sample was estimated to be between 99.80 and 99.95 wt pct. The chief impurities (aside from the tungsten core) were iron (0.04 pct), silicon (0.01-0.1 pct), aluminum (0.05 pct), carbon (0.03 pct). The tungsten core constituted 0.05 pct by weight of the sample. Although some alloying undoubtedly took place between the tungsten and the titanium during the deposition reaction, the core remained substantially intact in the deposited metal. The initial average hardness of the titanium as deposited was 105 Vickers (10-kg load). The maximum hardness was 116 Vickers and the minimum 91 Vickers. The metal was somewhat harder than that currently being obtained by the iodide process, that is, 75-90 Vickers. The rod was cold swaged to ¼-in. diam and then cold rolled in diamond shaped rolls to about 0.080-in. square, using reductions of 15 pct in area per pass. The 0.080-in.-square wire was cut into 6-in. lengths for the preparation of the alloys by the gaseous absorption and diffusion method. ADDITION OF OXYGEN, NITROGEN, AND HYDROGEN TO TITANIUM A modified Sieverts' absorption apparatus, shown in Fig 1, was used in

Jan 1, 1950

By Edgar Bain

IN STUDYING the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900° C. (1650°, F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement-the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1. shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 2, 1924

By John L. Boardman

BECAUSE of the attention that has recently been given to the health and safety of miners by various organizations such as the A.I.M.E., The American Congress, Mining Section, National Safety Council, as well as the Bureau of Mines and various state mining departments, your committee on health and safety deemed it best to call attention this year to the mine-accident cause that is by far the most important; namely, injuries due to falls of ground, rock, roof and coal. Each of several members of the committee contributed a brief outline of the importance of this accident cause in his district. While these papers were brief, it would require too much time and space to give them in full, therefore we present an outline of each and summation of all. REPORT OF M. D. COOPER, HILLMAN COAL AND COKE CO. M. D. Cooper, Division superintendent, Hillman Coal and Coke Co., Pittsburgh, Pa., contributed the following: During the period from 1930 to 1939. accidents from falls of roof in bituminous mines average 54.3 per cent of all accidents. In mechanized mining, there is a tendency toward reduction in this class of accidents because the operator of the machine is usually at a distance of 10 to 20 ft. from the face, whereas in hand loading the miner is close to the face during most of the shift. No doubt the use of aluminum and light steel beams supported at regular intervals by jacks, a common practice in mechanical mining, has contributed to the favorable record so far developed. REPORT OF M. H. FIES, DE BARDELEBEN COAL CORPORATION Milton H. Fies, Vice-President, DeBardeleben Coal Corporation, Birmingham, Ala., says: With reference to the types of mining, it is suggested that a clear understanding be had as to the character and thickness of the directly overlying strata, with especial consideration to the strength and in some cases an analysis of it. In coal mining, generally speaking, overlying strata higher in silica than others is stronger. In changing from narrow to wide places, the procedure should be experimental, both as to the width and depth of places and as to the nature of the necessary timbering. Since most of the accidents in coal mining particularly are due to falls of roof and coal, this phase of mining should be attacked with vigor There is no substitute for discipline and, in this connection, under present conditions it is important that cooperation by the labor organizations be sought and that a spirit of fairness prevail. Frequent and thorough inspection of all active working places should be made.

Jan 1, 1941

By John Carter Anderson

The theory of a zonal deposition of ores from ascending solutions which were differentiation products of a cooling magma, first propounded by Spurr,l in a measure explained by Lindgren,2 and recently re-emphasized by kemp,3 while perhaps accepted in principle by many mining geologists, so far has not been accepted as capable of practical application in the study and development of ore deposits. From his observations, the writer is convinced that there are laws governing the primary deposition of ores which, when properly worked out, will be of greatest economic value; and that the application of this knowledge to the development of new mines will mark an advance in the mining industry similar to that following the working out and application of the theory of secondary enriehiment. That there has been a tendency to a zonal distribution in the formation of ore deposits, by which the ores of one metal have been precipitated from tile mincralizing solutiolis at a greater distance from the source than those of another, cannot be disputed; and the nature of this zoning in a given deposit or district has been frequently described.4 But that a selection precipitation of the ores of two or more metals, other than lead and zinc, in successive zones may have taken place in a single deposit within limits economically possible of exploration is not generally recognized or admitted.

Jan 1, 1923

By John Carter Anderson

The theory of a zonal deposition of ores from ascending solutions which were differentiation products of a cooling magma, first propounded by Spurr,l in a measure explained by Lindgren,2 and recently re-emphasized by kemp,3 while perhaps accepted in principle by many mining geologists, so far has not been accepted as capable of practical application in the study and development of ore deposits. From his observations, the writer is convinced that there are laws governing the primary deposition of ores which, when properly worked out, will be of greatest economic value; and that the application of this knowledge to the development of new mines will mark an advance in the mining industry similar to that following the working out and application of the theory of secondary enriehiment. That there has been a tendency to a zonal distribution in the formation of ore deposits, by which the ores of one metal have been precipitated from tile mincralizing solutiolis at a greater distance from the source than those of another, cannot be disputed; and the nature of this zoning in a given deposit or district has been frequently described.4 But that a selection precipitation of the ores of two or more metals, other than lead and zinc, in successive zones may have taken place in a single deposit within limits economically possible of exploration is not generally recognized or admitted.

Jan 1, 1923

By T. V. Falkie, D. R. Mitchell

Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial and error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in coal mine haulage. This paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment, and is approached primarily from the standpoint of scheduling of the main haulage. Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial-error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in mine haulage. In many physical cases several probability distributions interact with each other in special ways, and it is not possible to solve for their combined effect in a mathematical equation. This is often true in the case of mine haulage, where such variables as number of empties or loads per trip, travel times, and number of cars or tons produced in a given time are probabilistic. By using a simple example of one secondary haulage segment of a large underground haulage system, this paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment. This is the type of preliminary research that will be needed as a first phase in any major haulage study, whether it be a relatively simple economic analysis or a plan for complete automation. The problem of optimization has been approached primarily from the standpoint of scheduling of the main haulage. It is evident that the method of proba-

Jan 1, 1963

By H. F. Yancey, M. R. Geer, C. L. Allyn, R. H. Eckhouse

Four coals were treated in the Humphreys spiral concentrator, and the products were examined by float-and-sink and screen-sizing tests to determine fundamental performance characteristics. The efficiency of the separation between coal and impurity was shown to be influenced greatly by particle size. FOUR coals exhibiting different washability characteristics were washed in the Humphreys spiral concentrator and the products examined by float-and-sink and screen-sizing tests to determine the mechanics of the separation between coal and impurity. With one coal, each 1/2-in. increment of the full width of the stream in the spiral was examined separately to determine where each size and specific-gravity fraction of the feed was stratified. The basic performance characteristics of the spiral were found to be the same for all of these coals. The coarsest fraction of heavy impurity stratified so far out in the stream that it could not be removed through the refuse ports and thus either entered a middling product or contaminated the washed coal in the case of a two-product separation. Impurity particles finer than about 100-mesh also were carried out in the main body of the stream and therefore were not removed in the refuse product. Little loss of clean coal in the refuse occurred in sizes coarser than 28-mesh or finer than 100-mesh, but considerable coal of intermediate size stratified in the stream that was drawn off through the refuse ports. Because of this modifying influence of particle size, the spiral is unable to make an efficient two-product separation between coal and impurity without some retreatment. Recirculation of a middling product through the same spiral as a means of obtaining more efficient operation was not attempted in this investigation. The size and specific-gravity composition of the middling product are, however, such as to render it amenable to simple hydraulic classification for recovery of coal. Retreatment of a middling product would improve the efficiency of the spiral, but even when making a substantial amount of middling, considerable clean coal enters the refuse product. Consequently, retreatment of a combined refuse-middling product would appear to offer greater promise for providing maximum efficiency. Because of the sizing characteristics of the spiral, a classified feed can be treated with higher efficiency than is possible on a natural raw coal. For this reason, semiclassified feeds, such as silt-bank or classifier-underflow materials, can doubtless be treated with higher efficiencies than those shown for raw coals in this report. Performance is, of course, only one of many factors that enter into the choice of cleaning equipment. The fact that the one company now using the spiral for cleaning coal has built a second spiral plant is ample evidence that the inherently low efficiency of this unit may be overshadowed by the low operating costs afforded by its extreme simplicity. Introduction A number of factors enter into the selection of coal-cleaning equipment, and most of them bear directly on the final cost of prepared coal. One of these factors is performance of the cleaning unit in terms of the efficiency of the separation it effects between clean coal and refuse. The importance of performance in the selection of a coal-cleaning unit varies with the difficulty of the cleaning problem. Obviously, if the character of the coal is such that only certain types of cleaning units are capable of yielding a clean product meeting market requirements, performance is of prime importance. If, on the other hand, the cleaning problem is so simple that any type of cleaner will provide coal of suitable quality, performance is important only insofar as it affects costs by determining the amount of salable coal lost in the washery refuse. With the objective of providing the coal industry with information that is helpful in the selection of

Jan 1, 1951

By R. H. Eckhouse, M. R. Geer, H. F. Yancey, C. L. Allyn

Four coals were treated in the Humphreys spiral concentrator, and the products were examined by float-and-sink and screen-sizing tests to determine fundamental performance characteristics. The efficiency of the separation between coal and impurity was shown to be influenced greatly by particle size. FOUR coals exhibiting different washability characteristics were washed in the Humphreys spiral concentrator and the products examined by float-and-sink and screen-sizing tests to determine the mechanics of the separation between coal and impurity. With one coal, each 1/2-in. increment of the full width of the stream in the spiral was examined separately to determine where each size and specific-gravity fraction of the feed was stratified. The basic performance characteristics of the spiral were found to be the same for all of these coals. The coarsest fraction of heavy impurity stratified so far out in the stream that it could not be removed through the refuse ports and thus either entered a middling product or contaminated the washed coal in the case of a two-product separation. Impurity particles finer than about 100-mesh also were carried out in the main body of the stream and therefore were not removed in the refuse product. Little loss of clean coal in the refuse occurred in sizes coarser than 28-mesh or finer than 100-mesh, but considerable coal of intermediate size stratified in the stream that was drawn off through the refuse ports. Because of this modifying influence of particle size, the spiral is unable to make an efficient two-product separation between coal and impurity without some retreatment. Recirculation of a middling product through the same spiral as a means of obtaining more efficient operation was not attempted in this investigation. The size and specific-gravity composition of the middling product are, however, such as to render it amenable to simple hydraulic classification for recovery of coal. Retreatment of a middling product would improve the efficiency of the spiral, but even when making a substantial amount of middling, considerable clean coal enters the refuse product. Consequently, retreatment of a combined refuse-middling product would appear to offer greater promise for providing maximum efficiency. Because of the sizing characteristics of the spiral, a classified feed can be treated with higher efficiency than is possible on a natural raw coal. For this reason, semiclassified feeds, such as silt-bank or classifier-underflow materials, can doubtless be treated with higher efficiencies than those shown for raw coals in this report. Performance is, of course, only one of many factors that enter into the choice of cleaning equipment. The fact that the one company now using the spiral for cleaning coal has built a second spiral plant is ample evidence that the inherently low efficiency of this unit may be overshadowed by the low operating costs afforded by its extreme simplicity. Introduction A number of factors enter into the selection of coal-cleaning equipment, and most of them bear directly on the final cost of prepared coal. One of these factors is performance of the cleaning unit in terms of the efficiency of the separation it effects between clean coal and refuse. The importance of performance in the selection of a coal-cleaning unit varies with the difficulty of the cleaning problem. Obviously, if the character of the coal is such that only certain types of cleaning units are capable of yielding a clean product meeting market requirements, performance is of prime importance. If, on the other hand, the cleaning problem is so simple that any type of cleaner will provide coal of suitable quality, performance is important only insofar as it affects costs by determining the amount of salable coal lost in the washery refuse. With the objective of providing the coal industry with information that is helpful in the selection of

Jan 1, 1951

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1952

By R. I. Williams

Kennecott Copper's mining activities in Arizona are conducted by the Ray Mines Div., located in Ray, Ariz., in the Mineral Creek mining district about 60 miles southeast of Phoenix. The Ray orebody lies in a mineralized zone belted on the east, west, and north by well defined faults. The orebody consists principally of schist with intrusions of quartz porphyry and diabase. The dominant ore mineral in the schist and quartz porphyry is chalcocite, with some native copper, and in most areas the orebody has been heavily oxidized. In the diabase the dominant ore mineral is chalcopyrite. Ore deposition in the schist portion is very erratic, with no apparent structural explanation. In 1873 silver prospectors opened the mining district, but it was not until 1899 that an English company made the first major attempt to exploit the copper deposits. This venture failed because of improper sampling and limited development work. In 1904 D. C. Jackling, Seeley Mudd, and Philip Weiseman became interested in the Ray Copper Co. and the Gila Copper Co., which later merged as Ray Consolidated Copper Co. In 1926 the Nevada Consolidated Copper Co. took over Ray Consolidated and in turn was taken over by Kennecott Copper Corp. in 1933. The extensive program of surface and underground development and exploration begun in 1907 continued through successive changes of management and ownership to the present time.

Dec 1, 1956