Search Documents

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. O. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico." The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter. There are probably plants at which a better preferential separation is being made than at Cananea. Many ores contain barren iron pyrite which, when depressed, does not carry copper into the tailing. Some concentrators use clean uncontaminated water for milling and in others the ore is ground much finer than at Cananea. All of these items are concerned in perfect separation. The details of preferential flotation at Cananea, therefore, are not presented on account of the perfection of the

Jan 1, 1928

By A. T. Tye

Regarding the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."l L. 0. Howard notes that "Perhaps the outstanding example so far published of improverrients in results through the use of selective flotation is that at Cananea, Mexico."" The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter. There are probably plants at which a better preferential separation is being made than at Cananea. Many ores contain barren iron pyrite which, when depressed, does not carry copper into the tailing. Some concentrators use clean uncontaminated water for milling and in others the ore is ground much finer than at Cananea. All of these items are concerned in perfect separation. The details of preferential flotation at Cananea, therefore, are not presented on account of the perfection of the

Jan 1, 1928

By Ian Wark

SODIUM sulfide is used extensively to increase the recovery of oxidized copper and lead minerals by flotation, particularly when using xanthates as collectors. It is generally assumed that the sodium sulfide converts a film of the oxidized mineral to the sulfide, and that the xanthate, while not a very effective collector for the oxidized minerals, is a good collector for the sulfide. On the other hand, Taggart and his collaborators' claim that unless sulfide minerals are oxidized they cannot adsorb xanthates and do not float. Gaudin2 states that amyl xanthate, used in conjunction with sodium sulfide, gives better results than ethyl xanthate. Rabone3 and Mayer-Schranz4 agree that excess of sulfide functions as a depressant. Owing to the greater solubilities of the oxidized minerals than of the sulfides, the consumption of sodium sulfide is greater than that of most other flotation reagents, up to 10 lb. per ton of ore being used in some plants. Luyken and Bierbrauer5 recommend a water washing to remove soluble heavy metal salts; by this means sulfide consumption may be reduced. It was desirable to determine the limits of the sulfide concentrations between which contact is possible at surfaces of anglesite and cerussite in xanthate solutions. Similar determinations were desirable for the sulfide minerals with which the oxidized minerals are usually associated, since conditions should be chosen, if possible, so that the two types of mineral will float together. Because of the formation, especially in acid solutions, of hydrogen sulfide and of the hydrosulfide ion (HS-), the permissible limits of sulfide addition are obviously dependent upon the pH value. Sphalerite responds to ethyl xanthate only in the presence of an activator; for example, copper sulfate. It was necessary, therefore, to determine whether sodium sulfide interferes with the activation of sphalerite by copper sulfate. The combined effect of sulfide and copper sulfate was determined also for galena, chalcopyrite and pyrite.

Jan 1, 1936

The Similkameen mine is located about 100 miles east of Vancouver, British Columbia, and ten miles west of Princeton, where the mine personnel live. Princeton was the first town in the British Columbia interior, originally the home of Cree and Blackfoot Indians and later settled by men of the Hudson's Bay Company, miners, cattlemen, and others looking for gold. After gold, there were coal mines and then copper mines . The Granby Consolidated Mining Company, Limited, operated the Copper Mountain ore bodies from 1926 to 1930 and from 1937 to 1957, mining 34 million tons of about 170 copper ore, mainly from underground. In 1966, Newmont Mining Corporation acquired the Ingerbelle property on the west side of the Similkameen River. Newmont then purchased the assets of Granby and formed Similkameen Mining Company to develop and operate the Ingerbelle and Copper Mountain ore bodies on both sides of the Similkameen River canyon. The Ingerbelle and Copper Mountain ore bodies lie within rocks composed of andesite tuffs, agglomerates, and argillites. Chalcopyrite mineralization occurs as a dissemination. Original ore reserves were estimated at approximately 75 million tons grading 0.52% copper. Mining is carried out on a three-shift, seven-day-week schedule at a rate of about 60,000 tons of ore and waste per day with four 10 cu yd P & H 1900 shovels which mine and load a fleet of 100-ton Lectra Haul trucks. Among the unique features of the design and construction of the Similkameen project was the construction of 4. 5 miles (7. 24 km) of new Trans-Provincial No. 3 highway by the company to the specifications of the British Columbia Department of Highways. The old highway traversed the Ingerbelle pit area. Along the relocated highway is a 4, 000 ft (1219 m) long berm which conceals the mine pit. This area has been replanted and now looks like the original forest scenery. Another interesting feature is that the tailings from the concentrator flow by gravity over a 1000 ft (34% m) suspension bridge, which crosses the Similkameen River canyon then passes through a tunnel to the dam site, a distance of 59,000 ft (17,980 m) to the cyclone station. When the Copper Mountain ore bodies are mined, the ore will be transported by belt conveyor on a second suspension bridge across the canyon to the Ingerbelle concentrator. After being loaded by the shovels into the 100-ton trucks, the ore is

Jan 1, 1978

That the chemical industries are alive to the situation that they now occupy in the sum of affairs is evident in the preparations being made by many firms for the Second National Exposition of Chemical Industries To be-held at the Grand Central Palace, New York City, during the week of September 25-30, 191 The list of exhibitors indicates that the Exposition is already twice the size of its successful predecessor. The American Chemical Society will hold its annual meeting during the whole week, the American Electrochemical Society has arranged to - hold its meetings on September 28, 29 and 30, and the Technical Association of the American Pulp and Paper Industry is also planning to meet during the week. The Bureau of Commercial Economics at Washington is again co- operating with the Exposition by arranging an elaborate program of motion pictures covering subjects dealing with the industries depending on chemistry. Many of these films will have their first showing at the Exposition. They will take the visitor through industrial plants, shops, manufactories, mines, etc., where visitors are never admitted; they will show operations that in ordinary light would never be seen; they will demonstrate more than any other kind of motion picture the great strides and improvement in the art of photography.

Jan 8, 1916

By L. L. McDaniel

ROLLER—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. 0. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico."2 The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter.

Jan 1, 1927

By R. B. Ladoo, C. A. Stokes, R. N. Secord, A. L. Hall

INDUSTRIAL mineral history shows that the entrance of new, nonmetallic minerals into commercial production can be expected to occur from time to time. Latest entrant into the field is wollastonite. Except for one short-lived period in Kern County, Calif., starting in 1933, wollastonite has never before been produced on a commercial scale. But the signs are up for its entrance as an economic factor in the mineral market. Small scale experimental production from a deposit near Willsboro, N. Y., started about 1943. A pilot plant was built in 1949-50 and irregular, small scale, production has continued. In early 1951 Godfrey L. Cabot, Inc. of Boston, world's largest producer of carbon black, took an operational lease on the property to study the deposits and make market surveys. This became Cabot's first venture in the mineral field, when they took over operations and began design of a new mill, expected in production in 1953. Properties The properties and major uses of wollastonite are comparable to New York fibrous talc. It has about the same specific gravity and index of refraction as talc, but is somewhat whiter and softer. The two most important fields of use, paint and ceramics, are the same as for talc. Ground wollastonite has a fiber length as much as 13 to 15 times the diameter. This particular property makes it applicable in the paint field and others. In addition, the length-diameter ratio may be controlled to rather narrow limits by choice of grinding method. Another important commercial property is brightness or whiteness. Wollastonite reads from 92 to 96 pct of MgO on the G.E. brightness meter for a 99 pct -325 mesh grind. Purity and uniformity of product are important. Chemically, the wollastonite now being mined analyzes SiO2 51.76, CaO 47.56, FeO 0.46, MnO 0.04, and H2O 0.09 pct. Theoretically pure wollastonite analyzes SiO2 51.75 and CaO 48.25 pct. This analysis indicates over 98 pct calcium silicate, with only small amounts of contaminating ingredients. That these ingredients are not detrimental to color or brightness is shown by the high brightness value of the fine ground material. [ ] By-product calcium silicate from electric furnace production of phosphoric acid has little physical re-semblance. to this wollastonite, being an off color white, and lacking in fibrous crystalline character. Minerology Wollastonite is a calcium metasilicate, CaSiO3, a white, medium hard, fibrous mineral. In this deposit wollastonite occurs as well crystallized aggregates of bladed crystals intergrown with garnet, and with a few percent of green diopside. The beneficiated product is about 75 pct wollastonite, 15 pct garnet, and 10 pct waste, largely middling. Wollastonite-garnet ore occurs in at least two beds. The main bed, varying in true thickness from 30 to 70 ft, dips into the hill at an average 30° and is enclosed in gneisses. Diamond drilling has proven the orebody to an average depth of 200 ft along 2000 ft of outcrop with adequate tonnage for many years of quarry operation. The wollastonite-garnet ratio varies locally, but average composition is uniform over long distances. A friable ore, it is easy to drill, shoot, and crush. Beneficiation Unlike talc this ore has to be beneficiated. Successful treatment depends upon the fact that it contains virtually nothing but wollastonite, garnet and a minor percentage of diopside. A very pure wollastonite product can be made by high intensity magnetic and/or gravity separation methods.

Jan 1, 1952

By E. W. Steele

IN THE copper-casting department of a modern electrolytic copper refinery there are two kinds of casting furnaces: the first, or anode furnace for casting crude copper into anodes for electrolysis; the second, or refined-copper furnace for casting the cathodes resulting from electrolysis into market shapes, such as ingots, wire bars, and cakes. Both furnaces are reverberatories of practically the same general design and are operated intermittently, putting through a charge normally in 24 hours. The treatment of the copper in both furnaces is similar, in so far that oxidation followed by skimming and reduction (poling) is carried on in both; but in the refined-copper furnace, the work must be done with greater care and it is of extreme importance that not the slightest trace of impurity be introduced into the copper. The furnaces usually hold from 150 to 300 tons of molten copper, which constitutes the daily charge. Except in the case of furnaces in the Lake district, where the concentrates from native-copper ores are charged through the roof, the furnaces are charged through the side doors by charging machines similar to those used in open-hearth steel practice. In 1916, at the Perth Amboy plant, of the American Smelting & Refining Co., located at Maurer, N. J., a study was made of the possibility of firing the copper refinery furnaces with pulverized coal instead of by hand. The proposed method possessed obvious advantages over hand firing and coal was a much cheaper fuel than oil at that time. It was realized, however, that there were several objections to its use, the principal ones being the liability of increasing the sulfur content of the refined copper, and the additional slag that might be produced from the ash. The increase of the sulfur content of the refined copper was the more serious, as more than 0.002 per cent. sulfur is objectionable. In the case of the slag, any increase would be expensive as the copper in this slag would have to pass again through the entire smelting and refining process.

Jan 3, 1925

By G. W. King, A. Bogrow, L. F. Marek

The purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction of FeO to Fe. Unless the gas has a CO!CO, ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles .at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available): the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity of the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"—i.e., the efficiency of conversion of the "available" CO supplied— is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1948

By L. F. Marek, G. W. King, A. Bogrow

The purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction of FeO to Fe. Unless the gas has a CO!CO, ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles .at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available): the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity of the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"—i.e., the efficiency of conversion of the "available" CO supplied— is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1948

By Hobart M. Kraner, E. B. Snyder

THIS paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, particularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercial blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. FACTORS AFFECTING CHOICE OF REFRACTORIES If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing temperature, which he in turn interprets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and resistance to the action of slag. In most refractory applications several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient stages and the progress is determined by measuring slight changes in. porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures . at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. -Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By Peter I. Brooker

Elementary estimation methods in which blocks are assigned values according to a geometrical area of influence concept are investigated for a tabular deposit. This quantitative assessment of the estimation technique is made using Matheron's geostatistics which allows the variance of the error between actual block values and estimated values to be found once the semi-variogram is known. For the deposit in question it is shown that the elementary technique makes poor use of the available information. There is a 20% relative error associated with it, whereas by using the optimal technique of kriging this can be reduced to 9%. An infill drilling program, which might have been suggested on area of influence results, would reduce the estimation variance only marginally over that of the current campaign; the relative error being lowered to 6%. Thus the geostatistical analysis shows this would be an unnecessary expense. The accuracy of an earlier drilling stage is also studied and it is shown that with the information available at the earlier stage block values could have been known with a relative error of 13%. Drilling could have stopped then if this were reckoned a tolerable error level. These results are all obtained for blocks whose size is dictated by the mining engineer and is set at the current grid size. In the area of influence approach smaller blocks are considered as the grid becomes finer and a study of the accuracy of area of influence estimates and kriged estimates for differing block sizes is presented. Between drilling stages more information from which the semi- variogram is calculated becomes available. The sensitivity of the estimation to changes in the semi-variogram parameters between earlier and current drilling programs is investigated.

Jan 1, 1977

"The zinc concentrator of the Butte & Superior Copper company, shown on the opposite page, represents an industry which is coming into importance in Butte. The existence of large bodies of zinc ore in some of the silver veins of Butte has been realized for years, but it is only recently that some of them have proved amenable to successful concentration. Most of the zinc ores thus far found in the camp are mixed with considerable pyrite, but those found in the Black Rock and Elm Orlu mines contain very little pyrite, so that a concentrate low in iron is possible.The Butte & Superior mill is rated at 1,200 tons daily capacity. The ore is sphalerite, most of which is finely disseminated through a hard quartz gangue, with small quantities of galena, pyrite, chalcopyrite, rhodocrosite and rhodonite. In mining, the included granite and the low grade vein matter are sorted out and used for waste filling so that the ore as it goes to the concentrator will carry about 20 per cent of zinc, 1 per cent lead, .25 per cent copper, 8 to 10 ozs. silver and a little gold. The ore bodies ranging from 5 to 103 feet in width, are mined by the square set method and filling of stopes with waste rock.The ore is hard and tough requiring extensive crushing and grinding equipment, consisting of Blake and gyratory crushers, 54-inch and 42-inch high speed rolls, Chili mills, Tube, and Conical mills. All of the lead con¬centrate and part of the zinc concentrate are recovered in the upper part of the mill by jigs and tables. The classifier overflow and the re-ground jig and table tailings go to settling tanks and from there to the Hyde Flotation process, where the balance of the zinc concentrate is recovered, and the tailing go to waste."

Jan 1, 1913

By Frederic Benard

This paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel colltent is low enough to permit the slimes to proceed to the dorè furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfartory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. . It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1943

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordi-nary, nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investi-gation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may he mentioned here that nickel dissolving electrochemically and entering the electolyte pre-sents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed sepa-rately below.

Jan 1, 1938

By Frederic Benard

This paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel colltent is low enough to permit the slimes to proceed to the dorè furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfartory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. . It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1943

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1938

By Nathaniel Arbiter, Chas. H. Behre

Two outstanding factors characterize most undertakings in the mineral industries: (1) mineral deposits are not equally distributed over the earth but are localized by natural processes, and (2) the mineral industries are largely based upon wasting assets. Neither of these factors is invariably true, for a few mineral materials, such as water, are essentially world-wide and others are replaced periodically by processes not unlike crop production. Indeed, with some, such as the salts in the sea, the supply is cyclic in short or long periods, whereas others, like water, though locally or periodically in short supply, are essentially inexhaustible. But to the extent that most minerals are limited to certain areas and are "permanently" consumed, any industry founded upon them, by implication, demands great care in planning for the most effective extraction-the essence of wise and conservative expenditure. Several less unusual yet also truly fundamental factors in the economics of the mineral industry are those involving (1) the various kinds and properties of mineral materials, which influence their use; (2) their geologic and geographic availability; and (3) the 'techniques unique to their discovery, exploration, and utilization. This chapter is designed primarily as a brief background for later ones and as a summary of the several unusual or at least special factors and of their effect upon the economics of the mineral industry. The social and political and especially the economic aspects of the industry are the main subjects of this volume and are dealt with in extended fashion in subsequent chapters. Fundamental Characteristics of Mineral Deposits DEFINITIONS Minerals are naturally occurring compounds of nonliving matter, each technically defined as having ( 1 ) a chemical composition that may vary

Jan 1, 1964

By E. B. Snyder, H. M. Kraner

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944