Search Documents

By R. C. Gifkins

R. C. Gifkins (CSIRO)—In this paper evidence is put forward to support the idea of grain boundary shearing in aluminum at 4.2°K and the phenomenon is explained in terms of a low-temperature "equicohesive temperature". It is stated that these findings show that grain boundary shear cannot be ruled out in any situation by temperature arguments alone. We believe, from our own recent study of "apparent grain boundary sliding'' at temperatures below 0.45 Tm, that it can be ruled out on temperature arguments alone.45 Our experiments were made principally with magnesium and a Ms-A1 alloy ("Magnox A12"). Careful examination of offsets of marker lines or steps at grain boundaries produced by deformation at room temperature (-0.3 Tm) showed many of these to result from curvature over narrow zones along the grain boundaries. A significant residuum did, however, appear as a sharp offset or step. It was found that the mean value of this step rose to a small value during the first 0.5 to 1 pct strain and then remained at this level with further strain. Moreover, exactly the same values were obtained (at the same stress) at 75°C instead of 21°C. That is, in this range of temperature the "apparent sliding" was not temperature-sensitive. At 125°C and above there was sliding which increased with strain and which was temperature-dependent. When this temperature-dependent sliding was used to calculate the sliding to be expected at room temperature, this underestimated the "apparent sliding" by a factor of 104. The conclusion drawn is that the "apparent sliding" consists of shear localized in a zone of a width measured perhaps in microns, whereas it seems that true sliding occurs on the boundary surface.46 A model for such localized shear has been developed in general terms, following a similar model of Urie and Wain.47 Other strong evidence for low-temper- ature sliding has been based on the offsets of marker lines consisting of a substructure seen using the electron microscope to resolve these.48 We have repeated this work and found that the effects can be accounted for in terms of cracks in an oxide film which is produced when the substructure is etched up; these cracks form over zones of shear rather than at actual interfaces. However, in aluminum at room temperature (-0.3 Tm) there is no "apparent sliding" which is optically detectable. We suggest that, when the temperature is much lower (and possibly the rate of strain higher, too), as in the experiments of Chin et al., then aluminum behaves like magnesium at room temperature, and a narrow zone of shear develops to accommodate differences in strain across the grain boundary. Such a zone could well give rise to triple-point cracks. It is hoped to investigate these suggestions further. B. Y. Chin, W. F. Hosford, Jr., and W. A. Backofen (authors' reply)—It is interesting to have Dr. Gif-kin's comments, although it is somewhat difficult to reply in detail without the reference containing the work that he describes. Apparently though, he does find a low-temperature temperature-independent sliding that would seem to be related to the observations reported here. Perhaps some of the difficulty has semantic origins, growing out of the distinction between ('true sliding" and "apparent sliding".

Jan 1, 1965

By Stephen Birch

THE Chitina mining district of Alaska is located at the headwaters of the Chitina and Copper Rivers. At present, the only producing min-ing properties are the mines of the Kennecott Copper Corpn. and the Mother Lode Coalition Co., which are situated 196 miles from Cordova the port of entry. The first claims, later acquired by the Kennecott Mines Co. and afterwards transferred to the Kennecott Copper Corpn., were discovered in 1900. The Copper River & Northwestern Ry., which connects the mines with tide water at Cordova, was completed in the spring of 1911. Contemporary with the construction of the railroad, aerial tram equipment was brought to the mines by pack train and a tramway, 3 miles, long, connecting Bonanza mine with the proposed railroad terminal, was finished, enabling shipments of high-grade ore to be made immediately on the completion of the railroad. A mill to treat the lower grade ore was begun the same year. The Kennecott company's holdings consist of 111 mineral claims. The Mother Lode Coalition Mines Co., which is controlled by the Kennecott Copper Corpn., owns 73 claims adjoining the Kennecott holdings. All data on operations and geology refer equally well to the Mother Lode property.

Jan 1, 1924

By J. D. Mote, J. E. Dorn

This investigation was undertaken to study the effects of piledup arrays of dislocations on inducing slip, twinning, and fracturing in magnesium bicrystals. A series of variously oriented bicrystals of magnesium having a vertical grain boundary were prepared and tested in tension. It was found that piled-up arrays of dislocations at the grain boundary could, under appropriate conditions, induce slip, twinning- and cracking. The results that were obtained substantiate, at least qualitatively, the general dislocation mechanism for transmission of strain across grain boundaries and the Petch-Stroh concept of fracturing. WHEREAS single crystals of magnesium generally exhibit extensive deformation, coarse-grained poly-crystalline magnesium at subatmospheric temperatures fractures after a few percent elongation.' Although a small amount of ductility is obtained, several features of this fracturing are characteristic of typical brittle behavior. Over a rather broad temperature range the fracture stress is insensitive to the test temperature and the fracture stress increases linearly with the reciprocal of the square root of the mean grain diameter. The course of fracturing is predominantly intergranular, but small fragments of adjacent grains frequently adhere to the fractured surface.2 The brittle behavior of polycrystalline magnesium is attributable to the limited number of facile deformation mechanisms it exhibits at low temperatures. For a general deformation of a randomly oriented polycrystalline aggregate, each grain must exhibit at least five independent mechanisms of deformation to permit accommodation of the imposed deformation from grain to grain.= Although minor amounts of prismatic slip occur in corners of grains where stress concentrations are known to be high, glide in polycrystalline magnesium at low temperatures takes place almost exclusively by basal slip.' The common type of twinning, which takes place on the (1012) pyramidal planes, can under the most favorable orientations, lead to a. strain of only 6.9 pet; the contribution of twinning to the tensile strain would indeed be much less than this in a randomly oriented polycrystalline aggregate of magnesium. Since the three mechanisms of basal slip are coplanar, they are equivalent to only two independent mechanisms, a number insufficient for a general deformation. Consequently, once the permissible twinning has taken place in conjunction with basal slip, no further plastic deformation is possible because of interference to slip at the boundaries of dissimilarly oriented grains. At this stage brittle fracturing takes place due to high stress concentrations at the juncture of slip bands with the grain boundaries; the predominance of intergranular fracturing in magnesium, in preference to transcrystalline fracturing which is prevalent in zinc, has not yet been rationalized. A more atomistic description of the plastic behavior and fracture characteristics of magnesium follows from the analyses made by stroh4 on the stresses induced by piledup arrays of dislocations. Slip first takes place by dislocation motion in the most favorably oriented grains. As the dislocations approach the boundary of a dissimilarly oriented adjacent grain they begin to form an array of dislocations with its attendant stress field. Piledup arrays of screw and edge dislocations introduce high localized shear stresses at the spur of the array; piledup arrays of edge dislocations also induce high tensile stresses localized in the vicinity of the grain boundary. Whereas the shear stresses can induce slip to take place, the tensile stresses, if sufficiently high, can cause fracturing. The localized shear stress will be relieved if sufficient numbers of mechanisms of deformation become operative in the original and the adjacent grain to permit accommodation of the dislocations in the grain boundary. In this event a ductile behavior will be obtained. But if the number of deformation mechanisms is insufficient for complete migration of dislocation arrays into the grain boundary, the tensile stresses due to the edge components of piledup dislocation arrays will continue to increase with increasing applied stress until fracturing takes place. Whereas face-centered-cubic metals have a sufficient number of mechanisms of slip for accommodation of dislocations in their grain boundaries to exhibit ductile behavior, hexagonal-close-packed metals, in general, do not. Consequently, hexagonal-close-packed metals are usually brittle except when conditions such as alloying or temperature permit facile slip by a number of mechanisms. The arguments presented above suggest that the mechanical behavior of magnesium depends on whether or not dislocation arrays in adjacent grains can enter the grain boundary. When such accommodation is possible, ductile behavior is expected; but when such accommodation is impossible, fracturing will ensue. To further test the validity of these arguments it was considered advisable to study the

Jan 1, 1961

By H. D. Wilde

At the Sugarland and Raccoon Bend fields in the Gulf Coast area, all wells are drilled with rotary tools and the casing is always set in cement that is placed by the circulation method. After the cement is set, the rotary mud that fills the hole is not withdrawn or bailed out; consequently, it is not customary to give the cementing job a direct test either by putting pressure on the hole to see whether the cement will hold or by observing whether an effective water shut-off is secured. About three years ago, this company started the practice of coring the cement left in the bottom of the casing and examining the core thus secured. If the core was hard and strong, the cementing job was judged a success but if the core was incoherent, soft, and crumbly, the job was considered a failure. Of course, there were intermediate types of cores and it was not always a simple matter from this examination to decide whether the job was a success or failure. After about two years, a summary of the core examinations that had been made indicated that of cementing jobs made at depths of 1000 ft. or less, 60 per cent.. were failures; of those between 1000 and 2000 ft., 80 per cent. were failures, and of those between 3000 to 6200 ft., 100 per cent. were failures. This sta,rtling table emphasized the need of the study of the conditions under which the wells were cemented and of adopting means to reduce the percentage of failures. In addition to these core tests, two wells gave direct evidence that the cementing jobs were not always successful. In one, a four-year-old well at Goose Creek, the casing was perforated, and when fluid was circulated some of the old cement wss brought to the surface. Most of it was powdery and the few chunks that were brought up were soft and crumbly. The other was a well at Raccoon Bend which during a blow-out brought a number of chalky, soft and crumbly pieces of cement to the surface. Suggested Explanations of Cementing Failures Efforts were made at once to explain the causes of these cementing failures. As all of the cements used were of a high grade and gave

Jan 1, 1930

By N. H. MacMillan, W. M. Mularie, R. E. Jackson, A. R. C. Westwood

The initial results of a study of the environment-sensitive microhardness and diamond rotary drilling behavior of granite and its constituent minerals quartz and feldspar (microcline)1 have established that many similarities exist between the environment-sensitive mechanical (chemomechanical) behavior of these materials and that of the simpler solids such as periclase, soda-lime glass, and alumina4 studied previously, at least as far as n-alcohol (straight-chain alcohol) environments are concerned. The results of this study (hereafter designated study I) also suggested that the rate of drilling of granite in these environments is controlled by the chemomechanical behavior of its quartz constituent, and is greatest in those environments which impart a zero l-potential to this phase, thereby maximizing its hardness. Now, cationic surface-active species strongly influence the l-potentials of silicate minerals. For this reason they are widely used in mineral separation operations. In particular, dodecyl trimethyl ammonium bromide (DTAB) was found in study I to produce f 0 for quartz at a concentration in water of 107 to 10-4 moles per 1. Accordingly, the influence of dilute aqueous solutions of this surfactant on the drilling behavior of granite also was examined in study I. This revealed that granite could be drilled three to four times faster in 10-° molar aqueous DTAB than in water, and confirmed by experiment the suggestion that granite is most effectively drilled with a diamond core bit in environments which impart a zero l-potential to quartz. According to O'Connor and Buchanan' however, the isoelectric point for quartz in aqueous DTAB solutions occurs at a concentration of .•.•2 x 10-° moles per 1, rather than [101 to 10-1] moles per 1. To confirm the results of study I, therefore, a more comprehensive investigation of the [ ]-potentials of quartz, microcline, and Westerly granite in aqueous DTAB environments has now been undertaken. At the same time an examination has been made of one of the basic assumptions of the current conceptual understanding of chemomechanical effects. In this view, although hardness changes occur essentially instantaneously following wetting of the solid, they are confined to a surface layer at most a few micrometers (µm) deep. Hence, to maximize the influence of chemomechanical effects on bit penetration rate only shallow cuts should be taken. Practical penetration rates are then obtained by increasing bit rotation speed. Experimental l-potentials were determined by the streaming potential technique using an automated rapid-cycling apparatus recently developed by Martin Marietta Laboratory from a design by Somasundaran and Kulkarni. The drilling studies employed 3.2-mm-OD 120-grit diamond-loaded core bits with a wall thickness of ~0.7 mm, and bit rotation speeds of 2200 and 25,000 rpm. The load applied to the bit was independent of the depth drilled in both cases. The 2200 rpm measurements employed the same drill press and puddle drilling technique as used in study I. The higher rotation speed was obtained using a water-driven dental turbine drill. In the case, the surface active fluid was pumped down the axis of the bit to ensure efficient wetting and flushing of the drilling debris from the hole. In both cases drilling rate was measured by the parameter D(200), defined as the average rate of bit penetration during the interval from 150 to 250 sec after drilling commenced.

Jan 1, 1976

By Glenn Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant.

Jan 1, 1929

By John B. Campbell, George G. Binder, Loren H. Jenks

Conventional methods of producing crude oil generally leave in the depleted reservoir 1 to 3 bbl of oil for every barrel brought to the surface. This paper describes a field test which explores the possibility of using gas-driven liquid propane to improve oil recovery efficiency. Laboratory theoretical and experimental studies leading to the field test indicated that low residual oil values could be obtained using limited amounts of propane driven by gas. The field test involved (I) repressuring the reservoir to the vapor pressure of liquid propane, (2) injecting the liquid propane, and (3) injecting dry natural gas to drive the propane and oil to the producing wells. Considerable preliminary work, including new drilling, work-overs, and a pressure survey was necessary. During the test, oil production rates have averaged about nine times the final primary rates. The field average GOR is still below the pre-test value. Oil recovery to date is 112,000 STB. About one-third of the 143,-000 bbl of propane injected has been produced to date. Results of the C-2 block test are encouraging and larger, more definitive field projects ore indicated. INTRODUCTION The cost of finding new crude oil reservoirs continues to increase. Today the oil industry is drilling more and deeper wells and making fewer big discoveries. Nevertheless, the demand for oil and oil products increases each year. It is natural that oil companies, faced with this situation, concentrate on recovering more of the oil existing in our known crude oil reservoirs. There is room for much improvement. For every barrel of oil brought to the surface by present day methods of producing crude oil, generally 1 to 3 bbl are left behind in the depleted reservoirs. The "unrecoverable" oil in petroleum reservoirs is largely "trapped" by capillarity. Since flushing with a solvent is exceedingly effective in combatting oil loss due to capillarity, much effort in this direction has been made in recent years1,2,3,4,5. Liquefied petroleum gas (LPG) has been suggested as a relatively inexpensive. abundant, easily recoverable solvent for crude. Some operators have observed striking responses in oil recovery at production wells offsetting input wells in LPG storage reservoirs6,7,8. In spite of the low unit cost of LPG, however, it is uneconomic in general to inject a volume of LPG into a reservoir to remove a like volume of oil. A modification of solvent flushing in which a limited quantity of liquid propane is gas driven through a reservoir appears capable of recovering much more than 1 bbl of oil per barrel of propane injected. Also, most of the propane injected should be recoverable for sale or re-use. Since such a process could well have widespread and profitable application, The Carter Oil Co. is making an extensive evaluation of the technique's possibilities. Laboratory development of the gas-driven propane recovery technique was sufficiently encouraging to justify testing in the field. Since 1952, the Production and Research Departments of The Carter Oil Co. have cooperated in a field test in the C-2 Block leases of the

Jan 1, 1958

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892

By R. S. Dean

ALTHOUGH it is obvious that in any flotation process we must have a froth, in recent years the development of collecting reagents has caused the possibilities of better frothing agents to be overlooked. Some investigators have even gone so far as to say that the number of satis-factory frothing agents was sufficient. A little consideration will show, however, that the reagents available in the past were far from ideal frothers. The properties of an ideal frother for flotation work may be set down as follows: 1. It. must form in low concentrations a copious but not too persist-ent froth. 2. It must be insensitive to hydrogen-ion concentration of the pulp; that is, it must froth equally well in an acid or alkaline medium. 3. It must be insensitive to salts, even in high concentration. 4. It must be absolutely noncollecting to both sulfides and nonsulfides. 5. Its frothing properties must not be affected by collecting reagents, including soap, the most generally used nonsulfide collector. 6. It must readily emulsify and disperse any insoluble collecting agent that is likely to be used. Clearly the existing frothers do not qualify. Pine oil, for example, is an acceptable frother for many purposes but if used in soap flotation a delicate balance between pine oil and soap must be struck because, as pointed out by Coghill1, these two reagents are incompatible in certain concentrations. The objections to soap itself as a frother are obvious, and the cresols and their substitution products all have some collecting Dower and very little emulsifying power.

Jan 1, 1935

A SELF-RESPECTING miner doesn't wash the cuttin's off his hard hat until he quits his job but, on the other hand, he keeps his lamp clean and a "spot" focus on the work at hand; the former habit is a matter of pride and the latter serves for efficient operation. During 1949, the mining engineer got all the "wet raises" for the problem of cutting costs to meet the drop of metal prices and keeping research work up to schedule when strikes tied up his work were his headaches. We note, not without admiration, that he hasn't washed the muck off his hat in token of surrender but, on the contrary, his light shines bright on the job to be done as can be seen in the following pages. Few people have any conception of how much ore and rock have to be mined and how much sorting it takes to cull a pound of copper from a 1 % ore body. These people would be even more startled to picture the problems faced by the engineer in mining and extracting, profitably, .2 oz of gold from a ton of ore as is done at some of our lode mines. Strikers have sometimes kept our researchers from their pilot plants and research laboratories, but the end of the year shows progress in making ore out of taconite and ferruginous sandstone, with a pilot plant in operation at Aurora, Minn., and plans for one near Birmingham. Unfortunately, it looks as though the mining engineer will have to make John Doe secure in mineral resources in spite of himself. Coal for steel, power, and to warm our homes is still economically possible, in spite of Mr. Lewis, through development of mechanized tools for mining. During the year, the use of continuous mining machines has extended, transport systems are being adopted to keep the ore flowing from the face to the tune of 40 tons per man-shift. Experiments in the gasification of coal are going forward in several places and may eventually extend our fuel reserves by the addition of coal seams now too lean for mining. Liquid fuel from coal, oil shale, or natural gas will become economic when oil consumption exceeds our supply; but, at less than 30 cents a ton direct cost for mining oil shale, the engineer is almost making it competitive under present market conditions. In this age of specialists, the mining engineer is still holding his own as a broad-gauge man. As a matter of fact, he is emerging from a stage of semispecialization as a coal, nonmetallics, or metal mining man to the realization that, with mechanization, mining is fundamentally materials handling whether it is fluorspar, coal, or copper ore. From the coal business come rubber-tired mechanical loaders to the iron mines of Birmingham. Shuttle cars are also finding application in the lead mines of the Tri-State. Open-pit methods are universal. Belt conveyors, trucks, Diesels, and mobile, jumbomounted drills are finding application in all types of mining. In preparation, such methods as flotation,- heavy density, electrical, and centrifugal are finding application in coal, nonmetallics, and metals. These concepts have been recognized by the mining engineer who has kept himself informed and has been quick to seize a method, machine, or a process from another operation and, with ingenuity, applied it to his problems. This, our Annual Review issue, is written by mining engineers. In gathering these separate articles under one cover for publication, we think of it as a trrbute to the tireless energy and skill of these men. They get little of the publicity accorded physicists, medical men, labor leaders, or company executives, but they supply raw materials without which industry would die.

Jan 1, 1950

By C. S. Roberts

The creep mechanism and kinetics of fine-grained magnesium have been studied over the temperature range 200&apos; to 600°F. As a result of a photographic study of microstructural changes, transient and steady-state creep components have been correlated with slip, subgrain formation, and cyclic deformation at the grain boundaries. THE approach of this research has been the blend of a quantitative study of the creep strain of polycrystalline magnesium as a function of time, stress, and temperature with direct microstructural observations of the operative deformation processes. The validity of the conclusions is dependent on the condition that the microstructural changes seen on the polished surface qualitatively represent those occurring in the bulk of the metal. The work was intended as much to lay a background to a study of highly creep-resistant magnesium alloys as to provide a description of the behavior of the base metal itself. The spectroscopic analysis of the electrolytic magnesium used in this study is as follows: Al, 0.009 pct; Ca, <0.01; Cu, 0.0011; Fe, 0.021; Mn, 0.012; Ni, 0.0004; Pb, 0.0012; Si, <0.001; Sn, <0.001; and Zn, <0.01. The impurity level is approximately that of commercial magnesium alloys. The original ingot was melted under Dow type 310 flux and cast as a 3 in. diam billet. It was extruded into 1 in. flat stock under the conditions: billet preheat 800°F (1 hr), container and die temperature 800°F, speed 3 ft per min, and area reduction ratio 45:1. The extrusion process was chosen in preference to rolling and recrystallization because it allowed easier grain size control from specimen to specimen. The grains of the extruded metal were fairly equi-axial and uniform in the size range of 4 to 6 thousandths of an inch. The preferred orientation of basal planes about the transverse direction was determined by an X-ray diffraction surface reflection method. A beam of filtered copper radiation was directed at an angle of 17" to both the transverse direction and the surface yet perpendicular to the extrusion axis. Analysis of the (002) diffraction arcs in the resulting photographic patterns gave an approximate intensity distribution along the great circle which extends through the center of the basal plane pole figure and to the extrusion axis poles. Successive layers of metal were removed by macro-etching between exposures. The extruded texture is relatively sharp, but the most significant point is the position of the maximum basal plane pole density and its variation with depth below the surface. Fig. 1 shows that this maximum is rotated 15" from the normal at the surface toward the extrusion direction. Such an inclination has been reported for extruded 1 pct Mn and 8 pct A1-0.5 pct Zn alloys.&apos; The inclination decreases until the maximum splits at about 0.025 in. depth into two elements of equal and opposite rotations from the ideal. The double texture persists to as great a depth as was experimentally convenient to examine. It probably continues to the very center of the extrusion. There is no great change in the sharpness of the individual elements of the texture with depth. A plate of metal about 0.015 in. thick at the surface of the extruded stock was produced by etching. A transmission diffraction pattern was made for the purpose of determining any preferred orientation of a direction in the basal planes. Relatively uniform {loo) and {101) rings were produced. There is little tendency for parallelism of a given direction in the plane with the projection of the extrusion axis on it. The creep specimens were machined from 6¼ in. lengths of the extruded stock. Creep was measured on the reduced section, ½x1/8X2¼ in. long. This section was electropolished on one side for the studies of microstructural changes during creep. An orthophosphoric acid-ethyl alcohol electrolyte was used under the conditions recommended by Jacquet.² Hand polishing was used for previous mechanical preparation. Electropolishing was continued until all mechanical twins had been removed. The electro-polished surface was protected from oxidation during creep testing by a thin layer of silicone oil. All micrographs were taken at room temperature on conventional metallographic equipment and after removal of the oil film. The creep tests were performed with machines which have been described in detail by Moore and McDonald." Five testing temperatures, 200°, 300°, 400°, 500°, and 600° ±3°F were used. Difference in temperature between the two ends of the specimen reduced section was 2°F or less. The testing was done at constant load. Strain readings were taken as frequently as necessary to develop usable creep curves. Tensile Creep vs Time, Stress, and Temperature A definition of terms is necessary. Whenever successive sections of a creep strain-time curve show decreasing, constant, and increasing slope with time they will be termed primary, secondary, and tertiary

Jan 1, 1954

By D. I. Bardos

The occurrence of Laves phases (AB,) in various binary alloy systems has been reviewed in recent papers.13 Iron forms Laves phases with Sc-, Ti-, V- and Cr-group elements. However, two of the corresponding Laves phases with cobalt, namely MoCo, and WCo,, are missing. Nickel forms binary Laves phases with Sc and Y, but not with any Ti-, V-, or Cr-group element. These conditions are schematically illustrated in Table I. That electron concentration is a significant factor in determining which type of Laves phase is formed in a given case was recognized long ago by Laves and Witte,4 This concept has been more recently applied to Laves phases formed by transition ele-ments. It now appears that the average electron concentration (average number of electrons per atom outside of the closed shells of the component atoms) may be an important factor also in determining whether or not a Laves phase can occur at all in a given system. As shown in Table I, in the transition element systems considered Laves phases are absent at electron concentrations of 8, or larger (to the right and below the double line in Table I). These absences clearly cannot be accounted for on atomic size considerations, as evidenced by the many inconsistencies apparent in Table 11. While the ideal radius ratio for Laves phases is 1.222, in the systems which do have Laves phases the ratios of CN 12 radii range from 1.10 to 1.46. The consistent absence of Laves phases at RA/RB< 1.10 might be attributed to the low values of these radius ratios. However, Table II shows that absences also occur irregularly throughout the radius ratio range covered. In a previous paper7 it was concluded that, in transition element systems forming u-phases, silicon may act as an acceptor of electrons, thus stabilizing the u-phase at electron concentrations higher than

Jan 1, 1962

By Norman D. Fitzgerald

The growth of domestic requirements for motor fuel has been phenomenal, rising year after year in a fashion almost unique among commodities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The complexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simultaneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpretation of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the problem is confined to the measurement of the influences of statistically

Jan 1, 1940

By Norman D. Fitzgerald

The growth of domestic requirements for motor fuel has been phenomenal, rising year after year in a fashion almost unique among commodities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The complexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simultaneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpretation of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the problem is confined to the measurement of the influences of statistically

Jan 1, 1940

By John Mark Patek

Knowledge of the relative floatability of silicate minerals is increasing in importance as flotation is being applied to the concentration of nonsulfides. Many silicates are in themselves commercial products amenable to concentration by flotation. Moreover, the selective flotation of other nonsulfide minerals, such as cassiterite, depends largely upon the floatability of associated gangue silicates. Differences in floatability existing between the various silicates have not- been sufficiently appreciated; for example, the feldspars that differ greatly in floatability have generally been merely treated as "feldspar." It was the purpose of the work described in this paper to determine by experiment the differences in floatability between silicates; to investigate the causes for such differences, and to discover a means of predetermining approximate floatability without the necessity of experimentation. Determining Floatability The relative floatability of 20 silicates so selected as to represent all of the more common silicate types1 was obtained by flotation tests enumerated in Table 1. The mineral to be floated was crushed dry on a steel plate, and screened repeatedly during crushing through an 80-mesh screen in order to produce a sand with all grains as close to 80 mesh as possible. The sand was placed in dilute (6N) hydrochloric acid until free of soluble foreign material, and then washed with tap water about ten times in order to remove both acid and fines. The resultant product, which averaged 82 per cent plus 200 mesh, was floated in 50-gram charges in a 50-gram Denver celluloid flotation machine with 0.008 gram of terpineol, and from 0.01 to 0.05 gram of oleic acid in a solution acidified with sulfuric acid. The degree of separation of one mineral from another was determined by counting under a nlicroscope the grains of each mineral, both in the concentrate and in the tailings, and comparing their relative abundance in each. Unless the comparison showed a decided difference in amount,

Jan 1, 1935

By F. H. Daniels

IN this, paper it is my intention to, call your attention to* a few of the many producers using blast, now, in common use in Sweden, and also those constructed by the Washburn & Moen Manufacturing Company at their Quinsigamond Works. During a prolonged stay in Sweden the writer had an opportunity

Jan 1, 1881

By Mark Alling

INTRODUCTION A FEW years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner&apos;s language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 7, 1914

By Dr. O’Neil Thomas J., Donald W. Gentry

"We can easily represent things as we wish them to be..” -Aesop INTRODUCTION The first eight chapters of this book have primarily addressed the concepts and fundamentals associated with project valuation, particularly as they apply to mining-related projects. Specific emphasis was placed on the engineering and economic parameters and estimates necessary for quantifying line items in pro forma income statements and the subsequent calculation of net annual cash flows. Given these estimates of relative benefits, costs, and annual cash flows for a project, it then becomes necessary to convert these estimates into measures of relative desirability or attractiveness. The criteria and techniques typically utilized to determine project acceptability or desirability are, then, the topics of discussion in this chapter. Before proceeding it may be advantageous to put the problem of project evaluation into proper perspective by reiterating some of the fundamental concepts developed in Chapter 1. The basic premise set forth in this book is that the objective of the firm should be to maximize its value to its owners (stockholders&apos; wealth). This value or wealth is represented by the market price of the firm&apos;s common stock; consequently, the primary objective of the firm can be restated as one of maximizing the value (price) of the firm&apos;s common stock in the marketplace over the long term. This price, in effect, is an indicator or index of the market&apos;s perception of the company&apos;s progress and a reflection of the investment, financing, and dividend decisions made by corporate management. These three major decisions are inter- related and jointly impact the market price of the firm&apos;s stock. Therefore, if the objective of maximizing the value of the firm to its stockholders is to be achieved, an optimal combination of the three decisions will be necessary. It is important to emphasize that maximizing stockholder wealth is not the same as profit maximization or even the maximization of earnings per share. Corporate managers making decisions based on the objectives of maximizing profits and/or earnings per share must recognize that these objectives do not consider: (I) the timing or duration of expected returns, (2) the business and financial risks of the promised earnings, or (3) the dividend policy of the firm. Obviously all of these factors are of concern to the company&apos;s stockholders and will have an effect on the market value or price of the firm&apos;s common stock. Maximizing market price per share, or wealth maximization, is therefore the appropriate corporate objective and

Jan 1, 1984

By W. W. Gerberich, P. L. Hemmings, V. F. Zackay

ThE strain-induced martensitic transformation may be used to attain desirable combinations of strength, ductility, and fracture toughness. One of the parameters is the relative stability of the austenite. For example, it has been shown by Zackay et al.1 that the volume percent of strain-induced martensite is related to the combination of strength and elongation obtained. It has also been shown that the degree of transformation is an important factor in the crack propagation resistance of metastable austenitic steels.2 Considering both tensile and crack-propagation tests, it was of interest to see if there was any functional relationship between the amount of strain and the volume of strain-induced martensite. Previously,9 it had been shown that at room temperature, there was a relationship between uniaxial tensile strain and the volume percent of resulting martensite given by The data were obtained by plastically elongating tensile samples to a certain strain and then measuring the field strength to determine the strain-induced ferromagnetic volume. This was accomplished for two conditions having yield strengths of 229 and 233 ksi. The nominal composition of this material was 9Cr-8 Ni-3 Mo-2 Mn-2 Si-0.25 C-0.09 N. In evaluation of the strain-induced martensite at a crack tip: the question arose as to whether Eq. [1] would also be valid under triaxial stress conditions. Tests were conducted on 1/2-in. thick plate material having a composition of 9 Cr-8 Ni-4 Mo-2 Mn-2 Si-0.27 C. It was found that sectioning, polishing, and etching of fractured specimens could reveal the strain-induced martensite occurring at a crack tip. Care had to be taken to minimize the final polishing steps so as to avoid a smeared layer of strain-induced martensite. The method for taking metallo-graphic samples from fractured crack-line loaded type samples is shown in Fig. 1. Observations of the strain-induced martensite occurring at room tem-

Jan 1, 1970

By James Yancik

The Howe Coal Co. is mining the Oklahoma Lower Hartshorne bed which ranges in seam thickness from 38 to 42 in. and pitches approximately 7° to the northeast. The raw feed to the cleaning plant averages about 20% ash and 1.10% sulfur, being reduced in the cleaning process to 4.8% ash and 0.9% sulfur with a free swelling index of 8 or 8%. This coal rivals the Pocohantas seam in chemistry and coking characteristics but has better fluidity than the Pocohantas seam coal. The coal is presently being prepared for the Japanese steel market in an 85-tph pilot plant designed and constructed by Roberts & Schaefer. The cleaning-plant flowsheet is discussed in detail.

Jan 1, 1972