Search Documents

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,1 and his experiments have been described and summarized by Richards1 White's contributions seem to have passed unnoticed by Fahrenwald, 2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,4 USSR; Anselm5 and Grunder,6 Germany; and Rose and Evans,[6] Great Britain.

Jan 5, 1958

By E. L. Bruce

THE district of. Patricia, in the province of Ontario, lies northwest of the Albany River and extends northward to Hudson's Bay. Formerly this was the unorganized district of Keewatin, the southern part of which was divided in 1912 between the provinces of Manitoba and Ontario. The interprovincial boundary now runs north from Lake of the Woods for 275 mi. and thence northeast 375 mi. to Hudson's Bay. This district is comparable in size to all the older part of Ontario south of the Canadian Pacific Railway east of Lake Huron-thus it is roughly one-third of the whole of the present provincial area. The central part of this great triangle is one of the least accessible parts of Canada. From it streams flow southward to the English River, southeastward to the Albany, northward to Hudson's Bay and the Hayes River, and westward to Lake Winnipeg. None of the streams is large and canoe travel is not easy. The only industry it has ever had is the trade in furs. Until the development of the airplane on a commercial basis, the only means of travel was by canoe or dog-train. There is not a mile of railway in the whole district. The two areas to be dealt with lie in the southwestern part of Patricia. Red Lake is 50 mi. east of the Manitoba boundary and 75 mi. north of the transcontinental railway from Cochrane to Winnipeg. Woman Lake is 50 mi. farther east and slightly farther north. The late Dr. D. B. Dowling, of the Geological Survey of Canada, visited Red Lake and spent some time there during his exploration survey from Lac Seul to Berens River in 1893. He also visited the Woman Lake basin during the same journey, but his examination of it was much less detailed, the great area covered by him during the one field season making it impossible to make more than a hurried reconnaissance. Some prospecting in the Red Lake district followed Dowling's exploration, but the distance from railway was too great for any systematic work to be done.

Jan 1, 1928

By I. Fatt, D. N. Saraf

A method is described for measuring two- and three-phase relative permeabilities in sandstones or sand packs using a nuclear magnetic resonance (NMR) technique to determine fluid saturations. Two- and three-phase relative permeabilities have been determined on Boise sandstone using the NMR technique of saturation measurement. Three-phase relative permeability to water was found to depend only on the water saturation, whereas three-phase permeability to oil depended on both the water and oil saturations. Relative permeability to gas in three-phase flow was found to depend only on the total liquid saturation. INTRODUCTION Three-phase relative permeabilities are extremely useful in calculating field performance for reservoirs being produced by simultaneous water and gas drives. Three-phase relative permeability data are also needed for analyzing solution gas-drive reservoirs which are partially depleted and are being produced by water drive. Some thermal recovery processes involve three-phase flow which require three-phase relative permeability data for predicting reservoir behavior. Unfortunately, three-phase relative permeability measurements have rarely been made. Also, because of the scarcity of three-phase data, it has not been possible to date to relate other measured rock characteristics to the relative permeabilities with a great certainty. Leverett and Lewis,l Reid2 and Snell3 have reported three-phase relative permeability data on unconsolidated sands. Leverett and Lewis used ring electrodes spaced along the length of the sand sample to measure the resistivity of the sample which was assumed to be monotonically related to brine saturation. Gas saturation was determined from pressure-volume measurements. Oil saturation was obtained by material balance on the cell containing the sand sample. This method is involved and time consuming. Another difficulty arises from the fact that the resistivity of the sand is a function not only of saturation of brine but also of the distribution and saturation history of the brine in the pore spaces. Reid2 used a gamma ray absorption technique for measuring liquid saturation. This method has the disadvantage that total liquid saturation rather than oil or brine saturation is all that can be measured and still another method is required to determine the saturations of individual components. snel13 used a neutron bombardment method which also required a separate determination of the individual component saturations. Caudle et al.4 measured three-phase relative permeability on consolidated sandstones using vacuum distillation for determining fluid saturations. Distillation after each reading makes this technique very lengthy and time consuming. Corey et a1. 5 and Naar and Wygal 6 measured three-phase relative permeability on sandstones by the capillary-pressure method. Semipermeable diaphragm assemblies were used at each end of the core specimen to keep the water phase in the core. Gravimetric methods were used to determine fluid saturations. Sarem7 recently reported an unsteady-state method for measuring three-phase relative permeability on sandstones. This method is an extension of Welge's method8 for measuring two-phase relative permeability. Although Sarem's method is simple and comparatively fast, the assumptions involved may oversimplify the problem. Sarem's assumption, that in all rocks relative permeability to each fluid will depend only on the saturation of that fluid, seems to be rather unrealistic. Neglecting capillary effects at the end of the core is also a weak assumption. Donaldson and dean9 measured three-phase relative permeability using a method similar to Sarem's.

By R. M. Rose, K. A. Jones

Resistive measurements ulere made on superconducting niobium single crystals in transverse magnetic fields. Crystals were grouln in both high and ulfrahigh vacua, doped with stnall quantities of oxygen, and annealed in ultrahigh vacua at temperatures from 900' to 1350°C. Maxima in the fluxoid pinr~ir~g force were observedfor the [100] and [210] directions. The increase of the critical current density with dissoved oxygen was seen to saturate at relatively low concentration. This behavior, and the variation of J, and residual resistivity (as a function of oxygen content and annealing) of both clean and dirty gassy) crystals, is seen as a consequence of the formation of clusters with (210)~b habit planes and (200)ffo common boundaries. These suboxide clusters are apparenlly stable at high temperatures and very low oxygen concentrations. It is generally known that dissolved oxygen at concentrations well below the solubility limit sharply increases the critical current density of superconducting niobium.' Such a result would not be expected if Nb-0 solutions were random, not even as the result of segregation on the scale usually encountered in solid solutions. According to the Kim-Anderson theory of flux creep,' the critical transport current density is determined by the pinning force Fp associated with some feature of the microstructure. As the Lorentz force. a or (J X R), of the transport current in the magnetic field approaches Fp, flux creep and then flux flow occur. The pinning force is expected to be quite small if the heterogeneity involved is significantly smaller than tte range of coherency which for niobium is circa 250~.~ Although the strain field of an individual oxygen atom in the niobium lattice is relatively large, it does not seem plausible that individual atoms could be so effective as to account for the data. Also, ~ramer~ found that straining and strain aging specimens containing small amounts of oxygen on occasion decreased the residual resistivity. A possible explanation for the above behavior may be found in the work of van Ooijen and van der Goot,= who found that annealing changed J, for niobium foils containing oxygen, and they attributed the changes to ordering of the oxygen atoms. This phenomenon has been observed by other investigators using X-ray and PROCEDURE Cylindrical 4-in.-diam niobium single crystals with axial orientations [ill], [110], [112], and [oo~] were grown from pure niobium, see Table I for analysis, in an ion-pumped ultrahigh-vacuum system using the electron beam floating zone technique. Total pressure during growth was lo-'9 torr: the oxygen partial pressure was less than lo-" torr, as determined by a mass spectrometer. These crystals will be referred to as the "clean" crystals. Similar crystals were also grown in another system at a pressure of 5 X 10"6 torr. These crystals will be referred to as the "dirty" crystals. Specimens 14 in. long were cut from the as-grown crystals and one end was polished down to no. 600 carbide paper smoothness. A back-reflection Laue photograph was then taken in order to fix the crystallo-graphic directions transverse to the crystal. The critical current density J,, the current density necessary to produce a voltage drop of 1.0 pv between voltage leads placed a in. apart, was determined as a function of the magnitude and direction of the transverse magnetic field and of the oxygen concentration. The technique and experimental arrangement was essentially similar to that of Tedmon et al.' In the remainder of this paper, the azjmuthal angle $ for the field H is referenced to the [ I101 direction in all four crystals, and oxygen was added in small equal increments by anodization and annealing.7 The resistivity ratio, RR, of the resistance at room ternperature to that at 4.2"K (H =7.00 kG) was determined as well.

Jan 1, 1970

By C. W. Wark, Fred Wise

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By Fred Wise, C. W. Wark

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

W: 0. HOTCHKISS, Madison, Wis. (written discussion*).-Mr. George's paper on. "The Wisconsin Zinc District" is a very complete and clear description, which it is a pleasure to read. His discussion of the origin of the ores is the least satisfactory part, and Mr. George correctly states present knowledge when he begins his paragraph on a origin with the words "the general supposition is, etc." There is still much to be learned regarding the details of the processes by which the ores have reached their present situation. In this the Wisconsin district differs not at all from other mining districts. It is my hope that Mr. George and others, equally clear-thinking, who are in close touch with these operations will be able at an early date to give us more information on this subject.

Jan 3, 1918

By C. F. Jr. Park

HOG MOUNTAIN is in the north central part of Tallapoosa County, Alabama, about 13 miles northeast from Alexander City. The Hog Mountain Mining and Milling Co. controls 1658 acres of land and is the only company operating in the district. The principal mine workings are in sections 10 and 15, T.24N., R.22E. The region has been visited by geologists many times, has been briefly described in several papers,1 and mentioned in many others. No detailed map of the mine or vicinity has been published. The field work for this report was started in March, 1934, as part of the Public Works reemployment program. About a month and a half was spent mapping both the surface and underground geology. The mine owners and operators have cooperated in every way possible to facilitate the work. N. 0. Johnson, the mine engineer, E. W. Ells-worth, J. E. McCoy and J. G. Englebert have acted as assistants for part of the work. The University of Alabama and the State Geologist's office have aided materially by permitting free use of their libraries and laboratory equipment.

Jan 1, 1935

By John M. Hird

A section of unstable overburden that has hampered an all-dragline mining operations at Texasgulf's phosphate mine in eastern North Carolina, is being successfully removed by hydraulic dredging. Blocks are dredged, drained, and developed ahead of two large draglines that strip the remaining overburden and mine the 12-m section of ore. Dredging assistance has increased ore production, increased ore recoveries to a maximum, reduced unit costs, and has made it possible to reclaim mined-over land that would be left underwater mined by all dragline methods.

Jan 1, 1981

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By W. E. Keck, Paul Jasberg

The flotative properties of the principal minerals in Michigan's potential iron ores have been investigated to develop methods of bene-ficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on magnetite flotation, (2) the preparation of pure magnetite, (3) the development of laboratory procedure and (4) flotation experimentation. Literature on Magnetite Flotation.—For the purpose of this discussion, the results of previous work on the flotation of magnetite can be summarized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.—The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Wither-bee Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65-mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into — 65 + 200 and — 200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The —200-mesh material was rejected to eliminate possible introduction of error into flotation

Jan 1, 1939

By W. E. Keck, Paul Jasberg

The flotative properties of the principal minerals in Michigan's potential iron ores have been investigated to develop methods of bene-ficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on magnetite flotation, (2) the preparation of pure magnetite, (3) the development of laboratory procedure and (4) flotation experimentation. Literature on Magnetite Flotation.—For the purpose of this discussion, the results of previous work on the flotation of magnetite can be summarized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.—The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Wither-bee Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65-mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into — 65 + 200 and — 200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The —200-mesh material was rejected to eliminate possible introduction of error into flotation

Jan 1, 1939

By J. P. Hirth, G. M. Pound

The flux of evaporation J from {loo) , {111), and (110) planes of silver single crystals and from poly crystalline specimens was measured at 744°C under a high vacuum using a time average weight loss method. The evaporation coefficient a was computed from the measured flux and vapor pressure data through the relationship J = aPe/21rmkT. The evaporation coefficients for the close packed planes and the poly crystalline specimens were found to be about 0.4 providing tentative confirmation of the theoretical limiting law for evaporation of metal crystals, a = 73(P/Pe) + % . The (110) planes faceted to form (111) planes, resulting in a greater evaporating area and larger a . The evaporation morphology of the plane surfaces and the surfaces of spherical single crystals is described in some detail. RECENTLY a detailed theoretical analysis of the mechanism and kinetics of metal crystal evaporation was made.1'2 A mechanism for vaporization involving the recession of monatomic ledges across a metal surface was deduced, and evaporation rate equations were derived by considering the dynamics of these ledges. In most metals, the process of evaporation is one of dissociation of atoms from ledges, surface diffusion, and desorption. The gross vaporization rate is controlled by the surface diffusion and desorption rates. It was shown that the monatomic ledges, under the action of surface diffusion gradients, tend to assume a terminal velocity and spacing. Further, it was shown that crystal edges and grain boundaries are a ready source for monatomic ledges. In the case of evaporation of large, perfect crystals with clean, low-index surfaces, the kinetic treatment1 leads to a limiting law for crystal evaporation: where J is the gross flux of vaporization, a is the evaporation coefficient, Pe the equilibrium vapor pressure, m the atomic mass, k Boltzmann's constant, T the absolute temperature, and P the actual pressure of vapor over the crystal surface. Imperfections such as grain boundaries, pores, cracks, and macroscopic steps should have the effect of causing positive departures from this limiting law. Such an imperfection is a source for monatomic ledges, which, near their origin, are closely spaced and thus give rise to higher evaporation rates there. However, under many experimental conditions,' this effect should be negligible due to the relatively low concentration of imperfections. In general, a more important cause of positive departure should be screw dislocations, and the effect of these has been considered in some detai1.2,3 Monatomic ledges emanate from points where the surface is intersected by a dislocation with a screw component normal to the surface. The dynamics of ledges arising from a screw dislocation are similar to those of ledges arising from a crystal edge. There is a perturbed region near the origin where the monatomic ledges are, under certain experimental conditions, closely spaced and the

Jan 1, 1960

ASHBEL WELCH, LAMBERTVILLE, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and, should not be overlooked,-the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destroyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. His doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de- * Metallurgical Review, vol. i, page 1. † The remarks as here given, as in the previous discussion on steel rails, have all been written out or revised by the participants in the discussion, and represent, therefore, their mature views. It has been thought that this plan, when it can be carried out without doing any of the speakers injustice in debate, is much to be preferred to a strictly verbatim report. The remarks of Mr. Chanute were sent to the secretary after the. meeting, and although they did not form a part of the actual discussion, there can be no doubt of the desirability of including them in this report. The papers under discussion were “Rail Specifications and Rail Inspection in Europe,” by C. P. Sandberg ; " The Wearing Capacity of Steel Rails in Relation to the Chemical Composition and Physical Properties," by C. B. Dudley, and a Rail Patterns," by A. L. Holley. T. M. D., Secretary.

Jan 1, 1881

By W. J. Putnam, H. F. Moore

THIS paper gives a preliminary summary of results of tests on the resistance to fatigue under reversed stresses of steel subjected to cold-working and of tests to determine the effect of rest on the endurance of steel under reversed stresses. The tests of cold-worked steel were undertaken as part of an investigation by the National Research Council Committee on Fatigue Phenomena of Metals and were made by Mr. Moore; the tests to determine the effect of rest are part of an investigation now being made by Mr. Putnam. Both series of tests were made in the Materials Testing Laboratory of the University of Illinois. The preliminary results of these tests are reported now because it is believed that test data on fatigue strength should be available at the earliest possible moment; however, it should be clearly kept in mind that this paper gives preliminary results and is intended to encourage discussion rather than to give final conclusions. Before giving the data of the tests, the writers will explain the term "fatigue strength" as used in this paper and will discuss briefly the method used in interpreting the test data of repeated-stress tests. " The term fatigue strength, as applied to a material, may be defined as that maximum fiber stress that will cause fracture of the material after the repetition of any given number of cycles of stress, each cycle involving the variation of stress from a minimum to the above maximum. The fatigue strength, then, varies with the number, of repetitions occurr,ing in the lifetime of a structural or machine member and with the range of stress for each cycle of stress. The fatigue strength will be lower for a member in which the stress is completely reversed than for one in which the stress varies from zero to a maximum. In interpreting test data from fatigue tests under reversed stress, the stresses and corresponding numbers of repetitions required for failure are plotted on logarithmic cross-section paper. In 1910, Professor

Jan 1, 1920

By W. E. Keck

THE flotative properties of the principal minerals in Michigan's potential iron ores have been investigated to develop methods of bene-ficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on mag-netite flotation, (2) the preparation of pure magnetite, (3) the develop-ment of laboratory procedure and (4) flotation experimentation. Literature an Magnetite Flotation.-For the purpose of this discussion, the results of previous work on the flotation of magnetite can be sum-marized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.-The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Wither-bee Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65 mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into -65 + 200 and -200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The -200-mesh material was rejected to eliminate possible introduction of error into flotation

Jan 1, 1937

By Joseph Mac Donald

Stripped of its romantic possibilities, mining is a commercial business, carried on for the profit there is in it; and the business of the manager, in its ultimate analysis, is to make the profit as large as possible. The general manager of a mining company should keep himself personally familiar with all the details of its operations. If he fails to do so, chaos results, labor becomes inefficient, costs go up, and profits go down. Nowhere is this emphasized more than in Mexico. If the mining operations are extensive and complex, involving, besides the work of mining the ore, its transportation and treatment by various milling operations, and the marketing of the products, the business, to be carried on properly, must be

Jan 1, 1909

By Herbert H. Kellogg

DEPOSITS of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (-325-mesh) sand assaying 95.5 per cent Si02, and a very fine (-3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. EXPERIMENTAL PROCEDURE The Sample.-The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.-By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fraction was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper.

Jan 1, 1945

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroe1 and Richards,2 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,7 and Hayden8 to mention only some which have appeared in our own Transactions-and by Schulz,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867), reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger's methods, may, arouse new interest in the study of basic principles.

Jan 7, 1922