Search Documents

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By David E. Van Dillen

INTRODUCTION Current design practices for deep tunnels make extensive use of plasticity solutions by Newmark (1970) and Hendron and Aiyer (1971). These solutions are applicable to a circular tunnel subjected to a hydrostatic stress state in a Mohr-Coulomb plastic medium. The role of rockbolts is introduced into these solutions as a uniform internal pressure equivalent to the yield stress of the rockbolt pattern. The application of these solutions is hampered by their inability to consider the biaxial nature of the in-situ stress field or any surcharged stress, such as due to blast loading. As a means of considering the biaxial stress field, designers have turned to relatively costly alternatives, such as the finite element method. The recent work of Detournay (1983) simultaneously provided two generalizations to the state of the art of the analysis of circular tunnels. Whereas the solution of Newmark applies to nondilatant Mohr-Coulomb materials, and that of Hendron and Aiyer applies to materials having associated flow rules, the solution of Detournay covers materials of arbitrary dilatancy. Secondly, Detournay's solution is valid for biaxial stress states, as long as the problem remains statically determinate (St. John, Detournay, and Fairhurst, 1984). The topic of this paper is an investigation of various alternatives for introducing the effects of rockbolts into simple tunnel design charts developed using Detournay's solution. The study was conducted using the BMINES finite element code, into which rockbolt elements have been added (St. John and Van Dillen, 1983). These rockbolt elements allow for plastic deformation of the bolt, bolt

Jan 1, 1984

By C. V. Millikan, Herbert F. Beardmore

Declining Productivity Index, as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. If not recognized, it may be interpreted as representing an unsettled or unstable condition in a producing well. It forms the basis of a number of predictions as to future performance compared with the performance of wells in which the productivity index does not decline. The nost important of these are that: (I) the rate of oil production will decline more rapidly, (2) the gas-oil ratio will usually increase abnormally, (3) the amount of water ultimately produced will be negligible, if any, (4) stop-cocking will increase current production and decrease gas-oil ratio. When such relative well performance is indicated, it follows that certain reservoir performance and operating practices may be anticipated: (I) disappointing recovery, (2) longer natural flow, (3) no active water drive, (4) better evaluation of acidizing, shooting and reworking, (5) intermittent operation of wells, (6) smaller pumping equipment required. It is significant that the basis of these important predictions is bottom-hole pressure tests that can be made immediately after completion of the wells. Introduction "'Productivity index" is the number of barrels of oil produced per day per pound per square inch of differential pressure between the reservoir and the bottom of the well. "Declining Productivity Index," as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. Productivity index can be determined only when the rate of production can be stabilized. In most wells the rate of production and bottom-hole pressure are easily stabilized to give a constant productivity index for a period of many hours. A few produce so erratically as to preclude probability of an acceptable test in the usual sense. A satisfactory productivity index can be determined in some wells only by gauging the production accurately by hours, measuring the bottom-hole pressure continuously, and from these data calculating the productivity index for successive hours. Such figures frequently will have a decreasing value—that is, a declining productivity index—and when plotted on double. logarithmic cross-section paper with productivity index as ordinate and time as abscissa will be a straight-line curve. The angle between the curve and the abscissa is referred to as the rate of decline. Declining productivity index may appear to be the result of change in permeability to oil due to decreasing saturation of oil and increasing saturation of gas in the reservoir. It is possible that such is in fact the cause, but if so, more is involved than merely relative saturation of oil and gas. This seems evident because the rate of decline in productivity index is substantially the same regardless of the pro-

Jan 1, 1945

By T. A. Rickard

Among the names which won a world-wide fame during the golden age of the early fifties, Bendigo and Ballarat were to Australia, what the Yuba and Grass Valley were to California. The map of Victoria did not for a long time show the name of old Bendigo;* for this first and more distinctive name was replaced with the more English Sandhurst, just as the alluvial diggings gave place to quartz mining. Towards the close of last pear, steps were taken to give back the old name, as associated with the early days of rich alluvium, and more suggestive than the application taken secondhand from an English military academy. History. The first discovery of gold? in this district, was made in the autumn of 1851 ; but there has never been any certainty as to the day or the man. At that time the country around Bendigo Creek was a part of the Ravenswootl sheep-run, and its resemblance to the Forest Creek district (now Castlemaine), induced the first prospecting. It was late in November when the "rush" broke out; the shepherds left their flocks; the sylvan solitudes were disturbed by * The name of Bendigo is said to have been derived from a hut-keeper on the Ravenswood sheep-run, who on account of his fondness for " fisticuffs " was nicknamed Bendigo, after the prize-fighter of that name. It is not aboriginal, as is often supposed, but Spanish ; and equivalent to our Benedict. There must always be some confusion between the two names of Sandhurst and Bendigo; the town, and with it the gold-field, having been three tinies named. Several other old familiar names have been likewise unfortunately replaced by second-hand English ones; so that an old digger talks of Forest Creek when he means the modern Castlemaine, Mt. Ida for Heathcote, Growler's Creek for Bright, etc. I shall use the names Sandhurst and Bendigo interchangeably. The first discovery of gold in Australia, was made by E. H.Hargraves, February 12, 1851, near Bathurst in New South Wales. In August of the same year the discovery at Buninyong, near Ballarat, inaugurated the first of a series of rushes to the Victoria gold-fields.

Jan 1, 1892

By Arthur F. Taggart

ENGINEERING is the art of control of men, matter, and energy in timely concert to provide economically the material needs of man. Control requires knowledge of the thing to be controlled and of proven methods of controlling. Knowledge of man comprises understanding of what he is and of his reactions as an individual and in the mass to his surroundings and to other men. Knowledge of matter comprises understanding of its fundamental nature, its methods of combining into multitudes of animate and inanimate forms, the properties of these forms and their various utilities, their sources and availability. Knowledge of energy constitutes knowing what is meant by the term, its various forms and sources, the laws of convertibility, and the methods of transformation and transmission.

Jan 4, 1950

Discussion of the paper of L. A. DELANO, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1267 to 1286. L. A. DELANO.-Since this paper was written, our daily mill tonnage has increased, from 2100 tons to 2700 tons a clay. We now use 11,000 lb. of chrome-steel balls of 2 ½ -in. maximum diameter, for an average crushing capacity of 275 tons per 24 hr., this giving a much higher crushing efficiency. I wish to call attention to two typographical errors in my paper as published. On page 1271, Table 1, the screen analysis of ore at the Bonne Terre mill should be stated in inches instead of mesh. - On page 1272, "the rolls average 185 tons per 24 hr., and have shown by test that 250 tons per hour can be maintained" should, of course, read "250 tons per 24 hours." THE CHAIRMAN (0. M. BILHARZ, Miami, Okla.).-Is the increased mill capacity due to improvement in the re-crushing of middlings or to keeping middlings out of circulation and treating them separately? L. A. DELANO.-AS was shown in Mr. Rabling's paper (Bulletin No. 128, p. 1161) the tonnage was raised by about 400 tons by simply changing the arrangement of screen openings in the jig bed and using punched plate instead of woven-wire screen. Then, by adding a ball-mill, we are taking from the jigs a much larger tonnage of middlings than before or as much as the ball-mill will crush. By sending the ball-mill product to tables and flotation, the jig capacity for original ore is increased. CHAIRMAN BILHARZ.-In your opinion, the satisfactory operation of a Hancock jig on a given ore requires adjustment of the length of the different screens and careful selection of screen openings? L. A. DELANO.-I think it does. In order to decide what screen openings to use on the jigs, we did a great deal of experimental work, making screen analyses of the various hutch products, and then hand-sorting the galena, middlings and chat from each size screen to determine the percentage of galena in each. Then adjusting our jig screens, we gradually worked the process up to a very efficient basis. ERNEST GAYFORD, Salt Lake City, Utah.-I would like too ask Mr. Delano whether the work of the Allen cone has been quite as satisfactory as the manufacturers claim for it.

Jan 1, 1918

By W. S. Landis

In brief, this is the story of an attempt to Americanize a process originally developed in Europe. The story will be recited in two sections, the first dealing with the process as developed by the European engineers; the second containing the improvements and modifications of American origin, together with some details of the operating results of the unit as finally assembled. Developments in other directions in this same field have not, up to the present, pointed out an economic future for the process, therefore our record here is largely a report of development progress. Whether some particularly favorable location will be found at some future time for a commercial installation cannot as yet be foretold. The project is now at a standstill. The peculiar tools of the electrometallurgist should be of great interest to the zinc smelter. The low thermal efficiency of the zinc retort, its comparatively small-scale unit and its intermittent cycle as it stood in 1925, should make this art a particularly fertile field for the electric furnace. Yet in spite of years of work recorded in volumes of literature, and an expenditure of large sums of money, there is not a single electrothermic zinc smelter operating anywhere in the world. In this industry the electric furnace plays only a secondary part today. Historical The first serious proposal to use the electric furnace for the smelting of zinc ores was made by the Cowles Brothers in 1885, but their experimental work did not advance the art to any extent. The next investigator of this field was Dr. Gustav DeLaval, a Swedish engineer well known to the industrial world through his development of the centrifugal and the steam turbine. The DeLaval cream separator is a familiar household appliance in most parts of the world. Although Dr. DeLaval commenced his experiments in the field of electric zinc smelting in 1893, it was not until 1898 that he had a practicable furnace, even then operating but intermittently. His work was done at Trollhättan, Sweden. He continued to improve this early fur-

Jan 1, 1937

By D. E. Hyatt

Many flotation plants practicing pyrite depression, mills leaching gold and silver ores, blast furnace facilities, and many metal plating shops share at least one common waste-water constituent of particular environmental concern-cyanide. In free or complexed form, cyanide ion is an emotionally and technically problematical reagent whose removal from water deserves attention. The initial consideration of the fundamental nature of soluble cyanides is followed by a discussion of decomposition or removal options for simple cyanide species. Complexed cyanide reactivity is discussed as it relates to ongoing or proposed methods for the decomposition or removal of soluble cyanides. New approaches to cyanide removal are discussed.

Jan 1, 1977

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed' that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-' it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3' of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By R. S. Rickard

Chemical processing of ores has gained new im¬petus in recent years. The reasons are many. They range from the need to process ores that are difficult to beneficiate to the avoidance of pollution. Although many think of chemical processing as a hydrometallurgical operation there are other techniques. An example is chlorination. Chlorination, although examined and discarded by many investigators, is again being considered as a means of extracting uranium1, treatment of silver-lead ores2, and the recovery of base metals from pyrite cinder and ores3. Segregation roasting of copper and nickel ores, a process similar to chlorination, is another chemical treatment being revived.

Jan 1, 1970

By Harry E. LeGrand

Most mine operations are hampered to varying degrees by excessive inflow of water into mines or scarcity of water for processing the materials. These internal problems are compounded in many cases by such external hydrological problems as lowering of ground-water levels in areas outside the mine properties, subsidence of ground surface, adverse geochemical changes, and pollution. The development of a mine below the water table disturbs the natural ground-water system, causing a convergence in the flow of water from a surrounding area. The mine becomes the apex of a depressed cone in the water table. The fact that mines are commonly located in complex and somewhat anomalous geologic environments prevents an idealized treatment of the mine as a well that would be similar to a water well in a homogeneous aquifer having isotropic conditions. Yet, adherence to some principles of ground-water behavior is helpful when combined with an understanding of the local geology. A program calling for an appraisal of all pertinent hydrological conditions prior to mining and during various stages of development should supply adequate information for mine officials to anticipate difficulties and to allow for corrective measures. Before and during mining operations there should be a mine hydrology framework and plan, in which there is continual upgrading of such considerations as anticipated actions, consequences of actions, remedial plans, and contingencies.

Jan 1, 1973

By C. Schlumberger

THE object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,1 but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding?2 method, in which a series of measurements are made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is deter-

Jan 1, 1934

By M. J. Mullikin, J. B. Conway

Several different equation forms were studied to determine the extent to which each particular equation type yielded an accurate representation of a given set of first-stage creep data. Specially developed least-squares computer programs were employed to obtain unique solutions for the creep-equation constants. In studies of creep data for lead at 14.5"C, nickel at 70OCC, and arc-cast tungsten at 2400°C consistently good representations were afforded by a third-degvee polynomial in t113. Other effective correlations were obtained with the Andrade, Cottrell-Aytekin, and de Lacombe equations along with a third-degree polynomial in t112. A newly proposed creep equation involving a hyperbolic-sine term in t1'3 was also found to yield very satisfactory results. This appears to be the first use of such a functional relationship in the analysis of transient creep behavior. In general, the deformation behavior of a material subjected to a tensile load is described in a strain-time plot. Experiments have shown that, following the instantaneous elongation which results on loading, the instantaneous slope (i.e., creep rate) of the strain-time curve decreases gradually with time and approaches what appears to be a constant value. Equations, therefore, which are proposed to provide an analytical representation of such first-stage or transient creep behavior must be consistent with these observations. In other words, at time zero, these equations must yield a finite deformation value corresponding to the elongation on loading. Furthermore, the first derivative of these equations must exhibit a fairly high although finite value at time zero, and then values which decrease with time. It is also preferable, in general, that the derivative eventually assume a constant value at high time values. Although many studies of first-stage creep behavior have been made and numerous equation forms have been proposed for expressing this type of deformation behavior, it is still not possible to state with any assurance which functional relationship will be adequate for a given set of measurements. Parabolic relationships have been employed most extensively although logarithmic expressions have been shown to be applicable in some instances. Combined forms1 have been studied in considerable detail and have on occasion been found to be very effective. One such expression is that of iXndradea and involves a modified parabolic expression: where 1 is the instantaneous length, lo is the length immediately following load application, t is the time, and p and k are constants. Another combined form has been proposed by weaver3 as follows: where E is the instantaneous strain, is is the linear creep rate, t is the time, and a and b are constants.

Jan 1, 1967

By Carl Henrich

Aspen, the flourishing mountain- and mining-town of Pitkin county, Colorado, is located in the valley of the Roaring Fork, 11 miles above Glenwood springs, where that stream empties its waters into Grand river, a tributary of the Colorado. The Roaring Fork heads on the western slope of the Sawatch range near Grizzly peak, and runs in a general northwesterly direction to its junction with the Grand river. Of its numerous tributaries, Castle creek joins it just below the town of Aspen, the town being built on an extensive flat hounded on the northeast by the Roaring Fork and on the west by Castle creek. The latter heads at the junction of the Sawatch and the Elk mountains and flows northward between the two chains, until it empties into Roaring Fork. Opposite the town of Aspen, Hunter creek, coming westward from the western slope of Mount Massive, joins the Roaring Fork. About a mile north of Aspen, the bed of Hunter creek is at least 300 feet higher than that of the Roaring Fork at Aspen. Hunter creek forms thus, at its mouth, one of the best water-powers in Colorado. A portion of it is now utilized for electric lighting in Aspen, while in the near future, the whole of this magnificent natural power will be applied, through electric transmission, for hoisting, pumping and ventilating at different mines of the district. The mountain opposite the town of Aspen, on the east side of Hunter creek (which near its mouth flows southerly), is called Smuggler mountain, from the famous mine at the foot of it. On the other, or western, side of Hunter's creek (see map, Fig. I), a higher mountain rises, on the slope of which the regular dip of the Triassie or Upper Carboniferous red sandstone strata, alternating with white layers of the same rock, can be clearly seen from town. This mountain is called Red mountain, from the prevailing color of its rocky

Jan 1, 1889

By S. C. Fall

The basic aims of the drilling and blasting program at the Mission mine are fourfold: 1. To provide 100,000+ tpd of broken alluvium and rock material for shovel excavation; 2. To obtain fragmentation that will permit the most efficient digging of the broken material and provide an acceptable crusher feed; 3. To conduct the drilling and blasting program in accordance with approved safety procedures; 4. To obtain these objectives at the lowest possible cost. The material that is mined from the pit is divided into four different rock types and the overlying alluvium. Each of these materials is broken by using procedures tailored to its individual characteristics.

Jan 9, 1965

EVERY intelligent and practical investigator of minerals says that copper ore is found in various regions of the world and that among others Italy is very rich in it. But very little is mined there, perhaps because of a cowardly Italian avarice which has the power to make us lazy and indolent in carrying out those lofty and fine designs which should reasonably make us proceed swiftly, or perhaps because we are not prone to attempt extraordinary profit but only undertake those enterprises in which we are certain of a return on our investment. The reason for this might also be found in the meager possibility of success, which, since these things are not easily attempted because they are enormous undertakings of doubtful outcome, cools the spirit of men and in place of enthusiasm introduces the fear of loss, the fear of having to sacrifice not only time but also the work and money invested; then they think of the difficulty [II] of discovery, of the impossibility of full ownership, and of the necessity of excavating the mineral marrow from the hardest bones of the mountains with the brawn and efforts of men. To this is added the fear common to many that in attempting such things they may be called fools by certain ignorant and dissolute persons, and it seems better to them to be praised for becoming rich through usury and by many other infamous and illicit methods than to lay themselves open to the danger of censure from such as these. But there are those who deserve still greater censure, particularly princes and all rich and powerful persons, and theirs is an even more useless error than that of those who refrain for the above reasons. If the occasion and means present themselves for both attempting and continuing such a profitable and laudable affair as mining ores and if they hesitate solely because of cowardice or because they give ear to the bayings of ignorant hounds, or if because of their own willfulness they wish to remain prisoners of a detestable and ugly avarice, then this is their own loss.

Jan 1, 1942

By Corale Brierley

The effect of hydrogen peroxide (H202) on growth and respiration of Thiobacillus thiooxidans and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uarnium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were totally inhibited after contact with 0.82 mM H202. Complete inhibition of oxygen uptake by T. ferrooxidans occurred at 8.75 mM H202, and growth was inhibited after 6 hr exposure to 2.06 mM H202. Higher concentration of H202 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface.

Jan 1, 1980

By Harry Roeser

Short cuts for determining the constants of oil decline curves, with the method of least squares as a starting point, are presented and applications made to practical examples. The nature of the raw data does not justify rigid adherence to the orthodox theory but does lend justification to convenient methods of approximation within reasonable limits. If the conventional form y = kxn were changed to y = k(x + c)', methods of determining the curves would be simplified and greater uniformity in calculated results would probably follow. As A result of the publication, several years ago, of some articles on determining the constants of empirical formulas, the determining the constant's of types of curves used for estimating the production decline of oil wells was brought to the writer for study. Methods requiring a minimum of time and labor and a maximum of rigor were sought, as it appeared that the nature of the data from which such curves are computed and the relative uncertainty of occurrence of the events predicted from them did not justify close adherence to the theory on which the solution of such problems is ordinarily based. The technical deficiencies of the solutions presented in this paper, from the standpoint of the method of least squares, are readily apparent to those familiar with that method, but their presentation in detail here is irrelevant to the subject matter. However, it is the author's conviction, after a rather exhaustive study of the problem, that the value of the solutions lose little by the approximate application of the conventional theory. It must be understood by those who use these formulas that the solutions herein given, and the formulas based on them, are merely facilities to aid the valuation engineer in forecasting future events. It is assumed, also, that before application is made of them, prescient judgment based on the circumstances in each case, shows that the forecast has some probability of realization. On this basis only will these formulas be found useful.

Jan 6, 1924

By Richard S. McCaffery

A Research on iron blast-furnace slags has been in progress since 1922 in the metallurgical department of the University of Wisconsin, supplemented by observations, tests and critical examination of operating records at 10 furnaces. From the data thus collected information has been put into forms suitable for use by furnace operators and is given in this report and the three accompanying papers.' In the viscosity results reported, it is estimated that temperatures were measured within 5" C. and that the viscosity determination of the particular slag investigated is accurate within ± 4 per cent. In the viscosity diagrams in the various papers, the equal viscosity lines were drawn in such a manner that in all cases they are located correctly with respect to the actual experimental results, but when determining a viscosity for a particular composition from the diagrams, the viscosity may. be slightly less accurate than the experimentally determined viscosity for the same slag, for the reason that the iso-vis lines interpolated between the experimental results may be shifted slightly without violation of the experimental data. The viscosity diagrams represent our judgment of their position under the above conditions, and we believe the relative accuracy of viscosity data taken from the diagrams is more than sufficient for any use to which the data may be put. Hundreds of samples of slags synthetically produced in the laboratory and of actual furnace slags have been studied in various ways. The ranges of compositions of slags used for viscosity measurements are: silica 25 to 55 per cent.; alumina 0 to 35 per cent.; lime 25 to 55 per cent.; magnesia 0 to 20 per cent. These measurements were made at temperatures of 1250°, 1300°, 1350°, 1400°, 1450°, 1500°, 1550°, 1600" and 1650" Centigrade. Descriptions of apparatus, methods used and statements of the problems investigated have been published in the papers listed in the bibliography beginning on page 120.

Jan 1, 1932