Search Documents

By J. T. Michalak, H. W. Paxton

The recovery of the initial flow stress of poly-crystalline iron is characterized by a) a logarithmic time dependence; b) an increasing activation energy with increasing recovery; c) an increased ?,ate and fraction of recovery with decreased temperature of deformation; and d) an increased rate with increased deformation. Isochro)ml studies of the recovery of single crystals revealed more sluggish recovery. The original flou3 stress of single crystals could be regained by recovery anneals at 800"or 900°C. ThE great majority of the theoretical treatments and experimental studies of strain-hardening have been concerned with the close-packed lattices.' Very little effort has been expended on the bcc structure so that the theory of work-hardening of this lattice is essentially nonexistent. The limited amount of experimental data resulting from the direct studies on silicon-iron,2 low-carbon steel,3 and purified irons4"7 does not as yet permit a detailed analysis of the strain-hardening. Studies concerned with the effects of annealing following deformation have been few in number," have been somewhat limited in extent, and have had the disadvantage of using irons containing a substantial impurity content. The present research was undertaken to augment the limited knowledge we have of the characteristics of a bcc metal as regards strain-hardening and recovery from the strain-hardened state. The recovery of the flow stress has been employed since it was felt that the stress associated with the hardened state gives at least a fair qualitative description of the state of the imperfections causing the hardening. The study was concerned primarily with the recovery of flow stress following strain-hardening of polycrys-talline, zone-melted iron as a function of the amount of deformation, the temperature of deformation, and the time and temperature of the recovery anneal. A limited investigation of the recovery of the initial flow stress of single crystals of this same material as a function of the recovery temperature was also conducted in conjunction with the Lambot X-ray technique." MATERIAL The zone-melted iron used in this investigation was obtained through the courtesy of the American Iron and Steel Institute and Battelle Memorial Institute. The analysis, as given by the supplier indicated a maximum impurity content of 0.02 wt pct excluding those impurities listed in Table I. (The actual impurity content is very probably less than this since detection limits were considered as the amount of a particular impurity level.) Also listed in Table I are the interstitial impurity contents of the iron at various stages of experimental work indicating that these im-

Jan 1, 1962

By H. W. Morse

The experimental work on the oxidized copper ore at the New Cornelia mine at Ajo, Ariz., ended on Jan. 12, 1916. On that date final decision was made on the general nature of the process to be used in the 5,000-ton leaching plant, and on many of the details, as far as experience on a 40-ton scale could decide them. With the approval of the Board of Directors and the General Manager, John C. Greenway, we have compiled what seem to be the most interesting data on the results obtained during the experimental period. The most important part of the data resulted from the operation of a 1-ton and a 40-ton plant at Ajo. Experimental work on Cornelia oxidized ore dates back to April, 1912, and has been going on nearly continuously since that time. A good many variations from the original idea have been tried, but the process finally decided upon is in principle and in all of its details a simple one. The history of the leaching work on this ore has been brought down to about a year ago in papers presented to this Institute by Stuart Croasdalel and Dr. L. D. Ricketts.2 The present paper will, therefore, deal principally with the results obtained during the last year of the work. Preliminary Tests by Mb. Croasdale Preliminary tests were begun by Stuart Croasdale in July, 1912. A number of important points were definitely decided by his work. Among these were: 1. New Cornelia oxidized ore, not very finely crushed (to about 2-to 3-mesh) showed good extraction with 5 per cent. sulphuric acid. It appeared that better than 80 per cent. extraction could be expected. 2. The consumption of acid for this extraction was not prohibitive. It was apparently 3.5 to 4 1b. gross per pound of copper recovered.

Jan 1, 1917

By E. E. Anderson, R. L. Newacheck, J. Kohl

Radioactive materials were used underground before the advent of the nuclear reactor. Radium containing ores have been mixed with cements and other materials for later location in oil wells by gamma ray logging since 1940.1 Perforating bullets have been marked with radium salts,, and radioactive materials have been added to drilling muds to find the cause of "lost circulation."' More recently colloidal suspensions of radioactive cobalt-60 and silver-1103 and solutions of 1-1314 have been used in waterflooding operatiorns to determine injection profiles, flow paths and water velocities. In this paper a recent and interesting underground tracer application is discussed. Development work and field engineering were carried out under the direction of Tracerlab, lnc., with assistance from personnel of the client. A gaseous tracer, argon-41, was used in an attempt to determine the cause of leakage from an underground gas storage reservoir. STATEMENT OF PROBLEM This gaseous tracer application was carried out for the Natural Gas Storage Co. of Illinois. This company has developed an underground gas storage field 1,750 ft below the surface of the earth near the village of Herscher, Ill., about 60 miles south of Chicago. The total volume of gas stored in the field was estimated to be about 13 billion cu ft in the spring of 1954. The field has a maximum estimated storage capacity of 90 billion cu ft. The gas is contained in the Galesville sandstone, previously a water bearing formation of about 25 per cent porosity. The water as it is pushed out by the gas forms a barrier for the gas around the edge of the reservoir. Over the top and beneath the bottom of the reservoir are located several layers of impervious rock, which barring cracks or unplugged and unknown wells should act as seals. Twenty-one injection and withdrawal wells were drilled into the Herscher reservoir and gas injection was begun during the summer of 1953. After a few weeks of gas injection, evidence of gas leakage was detected at the surface; water wells began bubbling and losing prime, and dry spots in the fields indicated gas leakage from uncharted oil wells. In every case, the leakage could not be traced back any further than the water bearing formations a few hundred feet below the surface. An extensive search was made to locate uncharted oil wells which were believed to be possible channels for the gas from the storage formation to the water containing formation. Long-time residents in the area assisted in the location of several abandoned oil wells. The wells when located were cleaned out and either used as vent wells to relieve the gas pressure in the water formations, or were plugged with cement. None of the wells even approached depths which would endanger the soundness of the storage reservoir. All of the injection wells were tested for leaks in the casings by conducting neutron surveys and by other techniques. To detect any leakage up through the cement-filled annulus surrounding the casing, a section of the casing wall in one well was milled out. Then, plugs were installed above and below the cut-out section and pressure applied to the annulus, which proved conclusively that the cement was sound in that well. The well was then plugged with cement and abandoned. In another well, ammonia was injected into the well and a temperature log was made. It was hoped that a leak would be re-

Jan 1, 1956

By F. M. Doyle-Garner, A. J. Monhemius

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°C to 200°C (265°F to 392°F). Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions containing various metals, singly and in mixtures. Single solutions of Fe, Ni, Cu, Mg, and Mn precipitated [a]Fe2O3 Ni(OH)2 Cu2O + CuO, Mg(OH)2 and [?]Mn203 respectively, during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe204. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versatic solutions are similar to those for iron hydrolysis in aqueous solutions. Magnetic interactions between mixed carboxylate complexes are thought to be responsible for the homogenous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1986

By George Lehman

THE Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the ?shrinkage-stope" or "caving" methods ) a lower extraction of, the developed ore, at a lower mining cost. ORE-DRAWING TESTS To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or "caving" methods. As no definite information regarding the question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore.

Jan 9, 1916

Herewith are transmitted the joint report of the Treasurer and Finance Committee for 1934 and the reports for the same year of the Chairmen of the following Committees: Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for details of the year's activities. Finances.-Income for 1934 from all sources totalled $134,967 com- pared with $121,689 in 1933. The increase is accounted for principally by four items: $6000 increase in initiation fees and dues of new members; $1800 in current dues; $4000 in "back" dues; and $2800 in the sale of publications, including TRANSACTIONS volumes and technical papers in the form of "separates." In passing, it may be remarked that income from back dues during 1935 will be less than in 1934, for the obvious reason that the total amount of dues in arrears has shrunk and consequently there is less to draw from. Income from

Jan 1, 1934

By Boyd Dudley

THE material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridizing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. The object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value.

Jan 12, 1914

By Marion Rice

THE copper-mining district of Jerome, Ariz., is of such economic importance that the following brief notes may be of interest. The ore deposits are said by Ransome1 to be pre-Cambrian, and are contained in the pre-Cambrian schists of the region. In the vicinity of the mine (the United Verde) the schist stands nearly vertical .and strikes a little west of north. At least three varieties are distinguishable-(1) a green rock, schistose, on its margins but grading into massive material, which is evidently an altered dioritic intrusive; (2) a rough gray schist with abundant pheno-crysts of quartz, apparently an altered rhyolite; and (3) a satiny, greenish gray, very fissile sericitic schist that may be a metamorphosed sediment. The ore occurs in varieties (2) and (3), the main belt of dioritic rock (1) lying just west of the orebodies. The ore is said to follow as a rule the layers of fine sericitic schist. T. A. Rickard2 says that the ore at the United. Verde Extension mine is found at the contact of diorite and schist, that both diorite and ore are earlier than the regional metamorphism, and that the quartz porphyry (" rhyolite" of Ransome) is of post-Cambrian age.

Jan 9, 1918

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

By M. T. Hepworth, W. B. Sample

HYDROGEN solubility and linear contraction measurements were made at constant temperature on an alloy of titanium of constant oxygen-to-titanium molal ratio but variable hydrogen content. A cylindrical specimen of titanium (0.25 by 1.6 in.) containing 0.75 at. pct 0 and less than 0.03 at. pct N was cast from a master button of iodide process titanium which had been alloyed with titanium dioxide. Four vacuum fusion analyses, which were made along the length of the cylinder after the hydrogen solubility studies were made, revealed a variation of oxygen content of less than 0.02 at. pct. The specimen was introduced into a quartz furnace tube, annealed and outgassedat 1050"~ for about 1 hr, and then held at 800" * 0.5" for about 30 hr, during which latter time experimental data were taken. The leak rate to the furnace chamber was not sufficient to contaminate the specimen during the run as determined by leak-rate studies and vacuum fusion analyses for oxygen and nitrogen before and after the runs. The furnace chamber was attached to a modified Sieverts apparatus used to introduce measured quantities of purified hydrogen to the specimen. A quartz pushrod transmitted changes in length of the specimen to a Chevenard dilatometer. The push-rod passed through a vacuum grease seal to the dilatometer which amplified motion of the rod by a factor of 319. During hydrogen addition, the pushrod did not contact the specimen. Measured quantities of hydrogen were added to the specimen and equilibrium hydrogen pressures recorded as a function of hydrogen content. The solubility data, which appear in Fig. 1, agree well with a separate investigation made with a different apparatus. The solubility limit of the hcp a phase appears as an abrupt discontinuity in slope at 3.4 at. pct H. The solubility plot has been extended as a dashed line at this discontinuity in order to emphasize the discontinuity. The hydrogen content at which bcc P appears is not clearly defined. An arrow indicates solubility data were taken upon hydrogen addition. Upon reaching the arbitrary maximum hydrogen content of the run, the quartz pushrod was pressed against the specimen in order to record the change in length with hydrogen removal. A pressure of about 100 g per sq cm was required to overcome the friction of the vacuum seal in order to obtain reproducible linear contraction data. The contraction ratio ~2/1", change in length divided by original length, was set equal to zero for the maximum hydrogen content. The relative contraction of the specimen was observed upon removal of hydrogen in the following manner. The system was opened to the pumps for a few seconds and an unknown quantity of hydrogen was removed. The system was then isolated from the pumps by closing a stopcock and allowed to return to equilibrium. When the temperature returned to 800°C, the pressure stabilized, and contraction ceased, measurements of contraction and pressure were made. The hydrogen content of the specimen was then deduced by measuring the equilibrium PIydrogen pressure and referring to the solubility plot. Linear contraction was then plotted against interpolated values of atomic percent hydrogen. The justification for this procedure is the established reversibility of the hydrogen equilibrium.' Uniaxial compression was assumed to have no effect on hydrogen pressure. The isothermal linear contraction data are plotted on Fig. 1. An arrow indicates data were taken upon removal of hydrogen. The solubility limits of the two phase a i /3 region can be identified by discontinuities ill slope of the dilatometric plot at 9.1 and 3.4 at. pct H, agreeing well with other studies.' Dashed extensions of the plots emphasize the discontinuities. Isothermal studies of expansion made upon hydrogen addition gave curves of much smaller slope and less pronounced discontinuities. A uniaxial compressive stress tends to accentuate volume changes in going from the more open bcc phase to the hcp phase.2 Incomplete data on ex-

Jan 1, 1962

This Association is made up of Alabama members of the following technical societies: The American Society of Civil Engineers, American Institute of Mining Engineers, American Society of Mechanical Engineers, American Institute of Electrical. Engineers, American Chemical Society and the American Institute of Architects. The association organized last winter for the purpose of maintaining an organization among the technical men of the State of Alabama, to stimulate the development of the natural resources of the State, to foster public interest in all things beneficial to the State, to advance the interest of the technical profession in the State and to encourage social intercourse among its members. On June 30, 1917, an excursion was made to the power house of the Alabama Power Co. at Lock 12 on the Coosa River. This is the first meeting held outside of Birmingham and is also the first meeting to which ladies were invited. About 85 members and guests attended and the excursion was voted a great success by all present.

Jan 8, 1917

By Kenyon E. Richard, James H. Courtright

SILVER Bell is situated 35 airline miles northwest of Tucson, Ariz., in a small, rugged range rising above the extensive alluvial plains of this desert region. Its geographical relation to other porphyry copper deposits of the Southwest is shown on the inset map in the lower left corner of Fig. 1. The climate is semi-arid. Altitudes range within 2000 and 4000 ft. Opening of the Boot mine, later known as the Mammoth, in 1865 was the first event of note in the district's history. Oxidized copper ores containing minor silver-lead values were mined from replacement deposits in garnetized limestone and treated in local smelters. Copper production had approached 45 million pounds by 1909 when the disseminated copper possibilities in igneous rocks were recognized. Extensive churn drill exploration carried out during the next three years resulted in partial de- lineation of two copper sulphide deposits, the Oxide and El Tiro. Although the then submarginal tenor discouraged exploitation of these disseminated deposits, selective mining of orebodies in the sedimentary rocks continued intermittently until 1930, providing a production total of about 100 million pounds of copper.

Jan 11, 1954

By AIME

DURING the happy and peaceful years between the Treaty of Versailles and the third New Deal, metallurgy became one of the most cosmopolitan of the sciences. Any metallurgist can name some twenty or thirty scientists whose work, in this country, in England, in Germany, or in France, Sweden, Italy, or Japan was as well known in other parts of the metal-producing and metal using world as it was locally, despite the fact that many of these men never left their native land. One of these metallurgical cosmopolites is Augustus Braun Kinzel, former Chairman of the Iron and Steel Division, A.I.M.E., and now a Director of the Institute. Gus Kinzel, however, is not only a cosmopolite by reputation; he is also a cosmopolite in fact. For many years he commuted at least twice a year between New York and the rest of the world; he is, therefore, not only an expert on the art and science of metallurgy but is equally expert in world travel and can expound with authority on the comparative quality and especially on the cuisine of the great prewar steamship lines; and being a true cosmopolite, he knows, as well as he knows the iron-chromium diagram, the best vintage years in the Gironde, Cote d'Or, and Saone-et-Loire departments in France and along the banks of the Moselle and Rhine in Germany.

Jan 1, 1946

Two Canadian mining companies, Noranda Mines, Ltd., and Wright-Hargreaves Mines, Ltd., have agreed to buy $500,000 worth of shares each in Anglo-American Exploration Ltd., controllers of thousands of acres of possible oil-rich land in southern Saskatchewan and Manitoba. Samuel Clarence Nickle, Sr., reported as possible president of the newly formed exploration company, said that $20 million in assets have been accumulated by the firm, mainly in the Williston basin in parts of the Dakotas and Montana, aid extending into Southern Manitoba and most of Saskatchewan. The M. A. Hanna Co. reported a record profit for the seventh consecutive year with total 1951 profit reaching $14,081. The company handled a record 16.8 million tons of iron ore in 1951, compared with 14.9 million tons in 1950. The company is also preparing to open four iron ore mines in the Lake Superior district which are expected to produce more than 5 million tons annually by 1954. The company built two new iron ore concentrating plants at Mesabi range mines in 1951,a with a third plant going into, operations soon.

Jan 1, 1952

By T. F. Witherbee

(Read at the Amenia Meeting, October, 1878.) As the forms of blown-out furnaces are of much interest to iron-masters and metallurgists, the manner of taking the accompanying sections of the Cedar Point stack is here given. The diagrams show the original and also the final shape of the furnace after a two years and twelve days' blast, during which the following solid materials passed through it, viz.: Coal, 41,000 tons; ore, 57,000 tons ; limestone, 30,000; total, 128,000 gross tons. Product, 41 1/4 tons per day Bessemer pig iron. The apparatus used in taking the sections was a modification of that proposed by Mr. Frank Firmstone,* and consisted of a sliding rule, to follow around the circumference of the stack, which rule was connected by a string to a segment of a circle of 24 inches radius. The segment was carried by an arm which connected it to a hub as a centre, 2 inches in diameter. A second string was wound around the hub, and communicated motion to a pencil-carrier, the pencil of which marked out on paper the exact outline, and reduced it to a scale of 1/2 inch to the foot. The whole machine was made in about three hours, with the facilities of a carpenter's shop, and gave in operation every irregularity of the lining. The sections were taken at salient points, by lowering a hanging staging on which the apparatus was placed. Tracings from the paper of the machine were made, and, as in this case several copies were required, the tracings were glued on to thin sheets of basswood, and patterns carefully sawed out with a bracket saw. * Transactions, vol. iii, p. 106.

Jan 1, 1878

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917

By H. D. Hoskold

DuRing the last few years, various persons have been put forward as originators of some mechanical device for the purpose of finding distances without the use of a chain or other linear measuring-instrument, and among these, the Englishman, Gascoigne, 1639, is prominent as the first in England; while James Watt, 1771, and William Green, 1778, are also included in the list of inventors. It is possible that this useful and important problem occupied the attention of others prior to the date cited, and, consequently, it is difficult to decide what nation first gave birth to the inventor of an instrument for the object under consideration. A very important work appeared, not long since, in Paris, devoted to a history and discussion of some of the older and newest forms of surveying-instruments,* and at page 79 of that work a curious old instrument is exhibited, called Bigonometre, i. e., an instrument for finding distances and solving trigonometrical problems. in surveying. A copy of the diagram of the instrument exhibited in the book referred to is represented in Fig. 1. Having had an occasion to read the French work referred to, I communicated with the author of it, and he was good enough to reply that he found a diagram of this old instrument in a book published in 1597, by Danfrie, existing in the library of the Academy of Sciences, in Paris. Col. Laus-

Jan 1, 1904

By Wayne A. Greenwalt

A method that determines venture participation when the decision maker's level of risk aversion varies according to venture profitability and risk investment is presented. The decision maker's fundamental aversion to risk is established by the selection of a desired working interest for a venture that anticipates only a discounted payout.

Jan 1, 1982

By F. C. Schrader, Alfred H. Brooks

Last fall (1899) we had the good fortune to be able to spend a few weeks in the new placer gold-mining region of Alaska, which is known as the Nome region. Cape Nome, after which the region has been named, and which forms the southeastern corner of the Nome Mining District, is an unimportant promontory on the southern coast of the Seward Peninsula (see map, Fig. 1). The name Seward has recently been given to the great peninsula which forms the northwestern extremity of Alaska. To the north of it is the Arctic ocean, to the south Bering sea, while its wesbernmost extremity, Cape Prince of Wales, is separated from the Asiatic coast by the Bering straits. The coast line of the peninsula is of a cuspate character, consisting of a succession of sandy, crescent-shaped beaches and rocky headlands. The interior has been but little explored; but we know that it is comparatively rugged, the higher mountain peaks rising probably from 4000 to 5000 feet in elevation. The mountains have an easterly and westerly trend, and the water-shed between the two oceans probably nearly bisects the peninsula. At Golofnin bay, the southeastern part of the Seward peninsula, some spruce is found, but to the west the region is entirely timberless, except for a sparse growth of stunted

Jan 1, 1901

By Joseph W. Richards

The Ashio copper-mine of the Furukawa Mining Co. is situated 18 miles from Nikko, and 109 miles north of Tokyo, near the center of Japan. The mine-waters are run over scrap-iron, whereby most of the copper is precipitated as cement-copper, leaving iron sulphate with some copper sulphate in solution. After using in the wet concentrating ore-dressing plant, the waste water contains clay and ore-slimes. The only avenue of disposal of this water is the Watarese river; but as this flows through valleys in which the water is used for irrigating the rice-crops, it is necessary to purify and clarify the water before discharge. The water amounts to from 600 to 700 cu. ft. (from 17 to 20 cu. m.) per minute, and averages about 0.00028 per cent. of copper, representing more than 18 tolls of copper per month. The water carries H2SO4, FeSO4, Fe2(SO4)3, CuSO, and other metallic sulphates in solution, and clay, ore-fines, slimes and basic iron sulphates as suspended matters. To purify and clarify the water, precipitation by milk of lime has been used, in three different ways, as follows: I. First Method, Copper not Recovered. Milk of lime was run into the water, and the mixture run through six settling-ponds, and then through a sand filter into

Jan 1, 1913