Search Documents

In the seven years that have elapsed since the AIME World Symposium on Mining and Metallurgy of Lead and Zinc, there have been a number of significant milling innovations and trends implemented in lead-zinc flowsheets to either improve grade and recovery or to control escalating mill costs. First, mill controls and instrumentation, which only had a foot in the door in 1970, have become increasingly common. In Australia, research into automatic crushing control has been implemented by Mount Isa Mines, and in virtually any large lead-zinc mill worldwide, an assortment of on-stream x-ray analyzers, grinding circuit controls, level detection devices, and reagent metering methods can be found. The increased circuit control offered to mill operators by this new technology points to more efficient flowsheets, as well as to a greater dependence upon computer-controlled operation.

Jan 11, 1977

By Craig R. Smith, Warren Pfefferle

Tests were conducted utilizing large flat jack devices placed in a vertical slot for high pressure loading of rock to measure in-situ properties of a rock mass. The high pressure flat jack devices were used as a site investigation tool to obtain rock mass properties. Tests were conducted before and after a 100 ton surface high explosive detonation test to assess explosive effects on the rock. It was conclusively demonstrated by these tests that meaningful flat jack tests could be successfully accomplished; also, a significantly different response of the rock medium was measured as larger areas of rock were loaded. Surface jointing was severely disturbed by the explosion.

Jan 1, 1971

By Thomas P. Oxford, Leslie G. Bromwell

The waste clay slurry produced during beneficiation of Florida phosphate ore presents a major environmental problem. The large volume of waste requires impoundment in above-ground disposal areas surrounded by earthen dams. As the result of a comprehensive research effort, three approaches to improving clay dewatering involving admixing of sand tailings have been developed. These provide satisfactory performance and appear to be compatible with the technological and economic constraints of the industry. Means of determining waste clay characteristics and analyzing mining waste disposal situations by computer simulation have been devised in support of the planning and field testing effort. Detailed examples demonstrating the applicability of the computer programs are presented.

Jan 1, 1980

By Gilbert Soler

THIS year's Chairman of the Iron and Steel Division is a noted member of a small and select group of practical scientists now working in this country and in Canada to improve the production and properties and to reduce the cost of super-quality carbon and alloy steels; he is one of those all-important leavening agents-a man with his feet always on the ground but capable of putting his head into the clouds on occasion-that are so necessary in applying science sensibly to the practical problems of steel production. He is equally at home in a discussion of the free energy of deoxidizing reactions or the entropy of the formation of stable sulphides, and in a consideration of the relative advantages of the basic-electric and the open-hearth furnace for the production of rimming steels in the Detroit area. Gilbert Soler was born of American parents in Havana, Cuba, just forty years ago. He graduated as a ceramic engineer from Ohio State University in 1930 and received a Master of Science degree a year later. In 1940 he received the degree of metallurgical engineer from the same institution.

Jan 1, 1948

By R. V. Ramani, Christopher J. Bise, Robert Stefanko

Over 200 billion tons of coal reserves lie locked up in deposits west of the Mississippi River-and of this, well over 100 billion tons are recoverable only by underground mining methods. Yet, because of the associated problems of unfavorable economics and inadequate technology, western underground mines contribute less than 2% to the annual US coal production. In order to reach the billion-ton coal production level called for by President Carter, it a pears the majority of new coal development will come from the West. But for this to be possible, new mining methods and equipment must be designed to match the unique thick seam conditions.

Jan 10, 1977

By S. N. Sharma, William Davis

Because of diminishing energy resources and rising energy costs, every industry is forced to carefully examine its pattern of energy consumption. The copper industry is no exception; current smelting practice begs for technological innovations that would improve the efficiency of its energy utilization. The thermochemical simplicity of copper metal production, as shown in Fig. 1, is deceptive. Designed from the same basic principles, there are four major commercial processes either in use or under construction; and others, such as the Mitsubishi process, are being developed.

Jan 5, 1977

By D. R. Miller

Internal friction and elastic modulus variations in electrorefined titanium, iodide refined titanium, and alloys of the latter material with oxygen, nitrogen, aluminum, and zirconium were investigated. No oxygen peak was detected with electrorefined titanium but, provided precautions were taken to prevent increases in background damping, an oxygen peak at about 410°C could be resolved with each of the other materials. An additional partially resolved peak was observed at 500°C in a Ti-N alloy. An anomaly in the variation of rigidity modulus with temperature was observed. Possible mechanisms for the formation of any oxygen peak have been discussed. PRATT, Bratina, and Chalmersl investigated the internal friction of commercial purity titanium and alloys of this material containing 1.5, 3.5, and 4.5 at. pct O. With commercial titanium the internal friction curve consisted of two components, a background which increased steadily with temperature and a peak at about 600" C which was due to grain boundary relaxation. In the Ti-O alloys, however, an additional internal friction peak was observed at 430" to 450°C and, since this peak increased in height as the oxygen content was increased, it was thought to be associated with the presence of oxygen. The diffusion of oxygen in titanium at temperatures between 300" and 500° C is believed to have marked effects in its tensile properties2'3 and the present internal friction measurements were undertaken to obtain further information on this diffusion, using material of higher purity than that of Pratt et d. and an apparatus of very much greater sensitivity. In the course of the investigation a number of important limitations on the work of Pratt et al. were revealed and results have been obtained which emphasize the need for ensuring that in this type of experiment, internal friction is independent of strain amplitude and that the values obtained are reproducible. 1) MATERIALS AND APPARATUS The basis material from which the majority of the specimens was prepared was iodide-refined titanium, the major impurities in which were oxygen and nitrogen—the metallic impurities being present at concentrations less than 0.001 at. pct. The hardness of this material after arc melting, forging, and swaging to rods 1/4 in. diameter was Dph = 110. Specimens 10 in. long and 0.020 in. (0.51 mm) diameter were prepared from these rods by further swaging and wire drawing and were finally annealed in vacuo (5 x 10-6 mmHg) for 24 hr at 800°C. The oxygen alloys were prepared from iodide-

Jan 1, 1962

John Edward Stead, a past-president of the British Iron and Steel Institute, and an Honorary Member of this Institute since 1906, died at his home at Redcar, Yorkshire, on Oct. 31, 1923, after a long illness. For many years, Mr. Stead had been recognized as a leading authority in chemical and metallurgical matters, particularly those relating to iron; he gave freely of his experience by the contribution of papers to the twenty-eight technical societies in which he retained his membership as recently as 1920. He had been honored with the Doctor's degree by three English universities, and was elected a Fellow of the Royal Society 1219

Jan 1, 1924

By R. C. Hirschfeld, H. H. Einstein, R. W. Bruhn, R. A. Nelson

The objective of the model studies described in this paper is to determine the effect of planar discontinuities on the strength and deformability of a rock mass. A model material was used because it satisfied concurrently three requirements that available natural-rock samples did not: (1) low strength, which was desirable for minimizing the loads that had to be applied in the laboratory; (2) ease of producing test specimens with geometrically regular joint patterns; and (3) uniformity of the test specimens. The model tests were performed on specimens made from a single modeling material and tested under triaxial stress conditions with [u,=u,]. Results are presented in this paper for tests on specimens that had (1) a single joint set inclined at several angles to the major principal direction, including 0º and 90°, and (2) two joint sets that were mutually perpendicular, one set perpendicular to and one set parallel to the major principal direction. Several different joint spacings were used in each series. Future tests will include a series with two sets of joints that make oblique angles with each other and with the major principal direction. The results of model tests and tests on cores of jointed rock by several investigators (e.g., Müller and Pacher,l Moore,2 Krsmanovic and Milic,3 Hayashi,4 Rosenblad,5 Jaeger,6 and Lane and Heck 7, have contributed significantly to the design of these experiments, which are believed to be the first in which a comprehensive study has been made of the combined effects under triaxial loading of joint spacing and joint orientation (Fig. 1).

Jan 1, 1970

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.' These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By A. A. Collins

OF widespread interest to all lead metallurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process. † Older Methods Three older methods, i.e., 1. Dross plus siliceous ore and limestone. 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and anti- mony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from I to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about impossible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it was decided to experiment with the soda process. The Soda Process After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other sugge~ted the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1949

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage,-and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation. INTRODUCTION Cornucopia is in the southeastern part of the rugged Wallowa Moun-tains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal.

Jan 1, 1939

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

Jan 1, 1938

Jan 1, 1938

By P. F. Richardson, J. L. Perisho, W. J. Roe

Handling and transport of coal during the winter months can be a severe problem. The inability to unload frozen coal from rail cars produces serious economic and logistic problems due to transportation delays, rail car shortages, and demurrage on the rail cars. One method of dealing with the problem of unloading frozen coal has been to spray freeze conditioning agents onto the coal before it is loaded into rail cars. Both water soluble and oil based formulations have been used as freeze conditioning agents. The water soluble treatments generally contain a polyhydroxy alcohol, such as ethylene glycol, or salts of alkaline earth metals, such as magnesium chloride and calcium chloride, as freeze point depressants. The oil based treatments consist principally of hydrocarbons, such as No. 2 oil or diesel fuel. The authors' tests have shown significant differences in the effectiveness of these freeze conditioning agents, depending on the particular coal substrate being treated. These differences correlate with the coal porosity and inherent moisture of the substrate. In general, the greater the porosity of the coal, the smaller the effect of the freeze conditioning agents. Coal porosity has a greater impact on water soluble freeze conditioning agents than oil based products. The authors investigated the pore structure of a variety of coals using mercury intrusion. Findings were related to the effectiveness of different freeze conditioning agents as measured by unconfined compression strength tests. In general, coals with a large number of very small pores (between 0.05 µm and 0.03 µm) do not respond as well to freeze conditioning chemicals.

Jan 1, 1986

By R. E. Maringer, B. A. Wilcox, A. H. Clauer, J. H. Sovik

Internal friction measurements from 25° to 1100°C have been made on specimens machined from TD nickel bar. The use of miniature torsional pendulum specimens alloived damping measurements to be made on specimens whose axes were parallel to the original bar axis, at 45 deg to the bar axis, and at 90 deg to the bar axis. There was a marked difference in damping with varying specimen orientation, and this was related to the pronounced micro structural anisotropy of this material. Varying the microstructure by cold working plus re crystallization annealing also greatly affected the damping behavior. Recrystallization essentially removed the broad peak found at 400° to 650°C in as-received TD nickel, and in addition greatly lowered the background damping. DlSPERSION hardened metals such as SAP-type alloys (Al + AI2O3) and TD nickel (Ni + 2 pet ThO2) have been developed primarily to improve high temperature strength properties. There have been numerous damping studies on SAP-type alloys,1"9 and one of these6 showed that the damping capacity was greater than that of 99.5 pet pure Al from 25° to 600°C. Several preliminary observations on TD nickel10 and an experimental Ni-ThO2 alloy11 indicated that here, too, the damping capacity was quite high. A high damping capacity in TD nickel, combined with its relatively good high temperature creep strength, could provide an additional benefit for some high temperature structural applications. This work was undertaken to study the internal friction behavior of TD nickel bar over the temperature range 25° to 1100°C. In Ni-ThO2 and Ni-Cr-ThOz alloys, other properties such as steady-state creep rate,12 creep rupture life,12'13 modulus of elasticity,14 and ultimate tensile strength,14 are sensitive to orientation with respect to the primary working direction. Thus, in order to examine anisotropy effects in damping, studies were made on specimens machined with their axes parallel, at 45 deg, and transverse to the original bar axis. MATERIAL DESCRIPTION AND EXPERIMENTAL PROCEDURES The material used in this investigation was from the same £ in. diam TD nickel bar that has been studied previously.13'15 The structure typical of the as-received TD nickel is shown in Fig. 1, and additional details of the structure can be found in Refs. 13 and 15. Elongated grains are parallel to the bar axis and are about 10 to 15 u long and about 1 u in diam. This structure is very stable, since no recrys-tallization or grain growth occurred after annealing for 3 hr at 1300°C.13 The total ThO2 content was 2.3 vol pct and the particles ranged in diameter from 100 to 1000. The average particle diameter was 370Å and the mean planar center-to-center particle spacing was 2340Å. To examine the influence of grain and subgrain structure on damping, a section of TD nickel bar was swaged and drawn at room temperature from 1/2 in. diam bar to 0.040 in. diam wire (99.3 pct re-duction in area). The structure in Fig. 2 resulted after the wire was annealed for 3 hr at 1250°C. The recrystallized grains were much larger than the grains in as-received bar, but still showed considerable elongation in the direction of working. A high

Jan 1, 1970

By Theodore Simons

During the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-day to rework old clumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the ninieteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands arid slimes: The so-called concentrators and vanners, on the one hand, and the buddles and round tables on the other.' For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and econoillical than other machines. In recent years they have agaiu become the subject of close inves-

Jan 1, 1914

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Metallurgist wanted for research in iron and steel. Man with experience in mills preferred. Salary $4,000. No. 13. Opening for a few technical graduates to act as instructors in mining to men at the mines under the supervision of the State mine inspector. Salary $1,800 per year. No. 14. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Mining engineer and metallurgist open for engagement, as superintendent of mines or constructing engineer. Technically educated, with 14 years' experience in United States and Latin America in concentration, amalgamation, cyaniding, constructing. Just finished building large modern all-sliming cyanide mill in Central America. No. 18.

Jan 4, 1914

By Wilson Blake

As a part of a USBM-ASARCO cooperative rock-burst research program, a burstprone stope pillar at the Galena mine was successfully destressed. Destressing was accomplished by blasting a single line of long holes in the footwall of the vein. As a result of destressing, the pillar was fractured and softened; hence it yielded, releasing a large amount of stored elastic strain energy nonviolently. In addition, the high stress in the pillar was shifted out around the stope walls and in the sandfill. Both broad-band microseismic monitoring and seismic velocity surveys were used to evaluate the destressing test. The mechanics of destressing were determined by finite element computer model studies of destressing. Results of the field destressing test agreed remarkably well with the predicted results from the computer model.

Jan 1, 1973