Search Documents

By M. O. Holowaty, C. M. Squarcy

Bituminous coal furnaces give way to coke, and by 1880, the American iron and steel industry was growing at a tremendous rate. In the twentieth century, the number of operating blast furnaces was cut in half while pig iron capacity more than doubled. Bituminous coal furnaces Attempts to relieve the shortage of charcoal by the use of bituminous coal in American furnaces began quite early. Use of bituminous coal in the blast furnace was restricted to areas lacking anthracite deposits but rich in deposits of bituminous coaL The largest concentration of bituminous coal furnaces was in Western Pennsylvania, West Virginia and Western New York state. Other areas included Kentucky and southern portions of the states of Indiana and Illinois. The first trials were made in Pennsylvania around 1780. Gradually several more furnaces began charging coal with their burdens as a partial substitution for charcoal. These so called cheaters were numerous, especially in Western Pennsylvania, which around 1810 began to expand its ironmaking capacity to catch up with the Lehigh Valley and the Schuylkill According to the existing references, complete bituminous coal burdens began to be used in this area only around 1840 when the ironmakers hastily adopted the hot blast apparatus introduced from England. The majority of these furnaces were built, however, after 1844 when an extensive experimental program, carried out at the Shenango Steam and Water Hot Blast Charcoal, Coke and Raw-Coal Furnace produced favorable results, with coal containing up to 35 pct volatile matter. The furnace was located near the Shenango River on the Lackawannok Run, five miles northwest of Mercer, Pennsylvania. It was built, owned, and operated by David Hogeland of Mercer. The first furnace was built in 1836 or 1837 as a charcoal furnace. Soon, however,

Jan 1, 1961

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By H. F. Smiley, Fred Sehmann

The production of the North Central Texas area comes entirely from the Pennsylvanian section with the exception of one pool in Cooke County and one in Young County where oil has been, produced from the weathered surfaces of Pre-Pennsylvanian peaks overlapped by oil-bearing strata of Pennsylvanian age. In the southern part of the area the Strawn and Bend groups furnish the production, the Strawn sands being the predominating horizons at depths from 1500 to 3000 feet. In the northern part of the area including North Young, Archer, Wichita, Wilbarger, and Clay counties, the Cisco group has produced consistently for nearly 30 years from sands ranging in depth from 700 to 2500 ft. To our knowledge there are 13 separate producing sands in t,he Cisco group ranging from 200 to 1800 ft. in Wichita County. During the past three years, deeper drilling has opened three new producing horizons. A Canyon sand in Central Archer County has produced from 400 to 800 bbl. per well at a depth of 2200 ft.; and in the same pool, owned jointly by the Deep Oil Development Co. and Lindsay Drilling Co., a Strawn sand was found at 3600 ft. which produced 75 bbl. per day. In Southern Wichita County the Bend group has been found productive. A very oolitic sandy lime series from 3675 to 3942 ft. has produced in three wells drilled to date. During the past year the district has been producing under an extreme proration which accounts for the small production figures for 1932, as well as the few drilling activities at the end of the year. Table 1 presents the available drilling and production data compiled by the North Texas Oil and Gas Association.

Jan 1, 1933

By Robert Uhley, Tsvi Meidav, LeRoy Scharon

Before National Lead built an industrial plant on its Fredricktown property, some 100 miles south of St. Louis, a 750x500-ft area on the proposed site was investigated by electrical resistivity, seismic refraction, and churn drilling. Data were accumulated to prepare an isopach map of the overburden and to determine soundness of the dolomite bed- rock and the depth to bedrock at fixed points. The site was on a gently sloping hillside. Elevations above sea level ranged from 760 ft in the northwest corner to 820 ft along the eastern edge, giving a total relief of 60 ft. There were no major drainage features, but in the northern part of the plant site there was an indicated depression area which later was interpreted as reflecting subsurface conditions in the bedrock. No rock was exposed in the entire plant site area; the surface was characterized by soil and overburden.

Jan 2, 1959

By Secretary

The two papers by Mr. C. M. Rolker, " Notes on Certain IronOre Deposits in Colorado," and "Notes on the Leadville OreDeposits," printed at pages 266 and 273 of this volume, were put to press (owing to the author's absence from the country) without final revision by him. The following corrections are thus made necessary: On page 272, line 13 should read, "respectively 12 and 4 feet" (instead of 12 and 14). On the same page, line 6 from the bottom should read, " the remaining 360 feet" (instead of 320). On page 284, lines 23 and 21 should read, " 111 some places, the dolomite sand roof has remained thicker; and in isolated parts of the bed no replacement has occurred."

Jan 1, 1886

By Albert E. Wiggin, Frederick Laist

Page I. Introduction............................470 II. The Sources and Amount of Slime................470 II. The Composition of the Slime..................471 IV. The Experimental Development of the .Anaconda Slime Plant.. 471 1. The Great Falls Slime Plant and Experimental Work......471 2. The Experimental Work Done at Anaconda..........473 (a) SlimeThickening Devices.............. 474 (b) SlimeConcentrators................. 475 (c) Dewatering the Slime Plant Concentrate......... (d) The Use of Chemicals to Accelerate the Settlement of Slime........................ 478 (e) The Effect of Temperature upon the Settlement of Slime 478 V. A Description of the Anaconda Slime Plant........... 479 1. A Diagrammatic Flow Sheet of Plant............. 480 2. The Slime-Thickening Division................ 480 3. The Concentrating Division.................. 481 4. The Concentrate-Dewatering Division............. 483 5. General Data........................ 484 I. IntRoduction The new slime-concentrating plant at the Washoe Reduction Works, Anaconda, was put into operation during March, 1914. This plant, which has a capacity of 26,000,000 gal. of slime pulp carrying 2,500 tons of solid matter per day, consists of Dorr thickeners and Anaconda multiple-deck slime concentrators. This plant is the culmination of a great deal of experimental work extending over a considerable period of time, which , work will be described briefly in the following pages. II. The Sources and Amount of Slime Up to the beginning of this year, the ore from the Anaconda company's mines in Butte, Mont., has been concentrated both at the Great Falls

Jan 1, 1915

By M. J. Virnig, G. A. Kordosky, K. D. MacKay

LIX 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mill's LIX 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1978

By M. F. Werneke, J. A. Jones

Abstract- The use of a unique class of sulfhydryl collectors, the monoalkyldithiocarbamate salts ([RNHCS]) as direct collectors for malachite and azurite is presented. Microflotation and laboratory scale flotation tests were performed to define the collector properties of these reagents under a variety of flotation conditions. On the basis of the results, it is proposed that some property of the amine-hydrogen atom in the reagent has a significant influence on the unusual activity of these collectors for oxide copper minerals.

Jan 1, 1978

By Herbert Clark Hoover, Lou Henry Hoover

As stated in the preface, the nomenclature to be adopted for weights and measures has presented great difficulty. Agricola uses, throughout, the Roman and the Romanized Greek scales, but in many cases he uses these terms merely as lingual equivalents for the .German quantities of his day. Moreover the classic language sometimes failed him, whereupon he coined new Latin terms adapted from the Roman scale, and thus added further confusion. We can, perhaps, make the matter dearer by an illustration of a case in weights. The Roman centumpondium, composed of zoo librae, the old German ceniner of 100 pfundt, and the English hundredweight of 1112 pounds can be called lingual equivalents. The first weighs about 494,600 Troy grains, the second 721,900, and the third 784,000. While the divisions of the centumpondium and the centner are the same, the Libra is divided into 12 unciae and the pfundt into 16 unizen, and in most places a summation of the units given proves that the author had in mind the Roman ratios. However, on p. 509 he makes the direct statement that the centumpondium weighs 146 librae, which would be about the correct weight if the centumpondium referred to was a ceniner. If we take an example such as " each centumpondium of lead contains one uncia of silver", and reduce it according to purely lingual equivalents, we should find that it runs 24.3 Troy ounces per short ton, on the basis of Roman values, and 18.25 ounces per short ton, on the basis of old German. If we were to translate these into English lingual equivalents of one ounce per hundredweight, then the value would be 17.9 ounces per short ton. [ ]

Jan 1, 1950

INSTITUTE MEDALS AND PRIZES ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as fol¬lows. the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saun¬ders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony-on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1 The award shall consist of two prizes first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material

Jan 1, 1923

ASIDE from the John Fritz Medal, in which the Institute partici¬pates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as fol¬ lows the Robert W Hunt Medal and Prize, the J E. Johnson, Jr , Award, the James Douglas Medal, and the William Lawrence Saun¬ders Medal ROBERT W HUNT MEDAL AND PRIZE The partners of Robert W Hunt established a fund which was, presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded tinder the following rules¬ 1 The award shall consist of two prizes first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member' over 40 years of age, but under unusual circumstances, both prizes may be allotted to one per son provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on non and steel The scope of the term "iron and steel" shall be determined by the sub-committee consideing the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main con¬ti ibutions to the industry have been in the improvement of production and quality of material

Jan 1, 1923

By AIME AIME

EUGENE AUSTIN STEPHENSON, better and affectionately known as "Steve," has long been an active and enthusiastic member of the Petroleum Division of the Institute. As its Secretary-Treasurer for several years, he was the spark plug that so successfully carried the Division over the trying period of the early thirties. "Steve" was born at Franklin, Mich., July 27, 1883; graduated from Adrian College in 1905, and later received his Doctor's degree from the University of Chicago where he was an instructor for two years. From 1917 to 1925 he was chief geologist for the South Penn Oil Co. and from 1925 to 1930 he was associated with Ralph Davis, Inc., of Pittsburgh, consulting engineers. In 1930 the Missouri School of Mines called him to Rolla to head a department of petroleum and natural gas engineering. and in 1938 he was invited to build up a similar department at the University of Kansas.

Jan 1, 1941

By W. S. Ayres

[Secretary's Note.—At the Spokane meeting of the Institute, in discussion of President Brunton's address on "Modern Progress in Mining and Metallurgy in the Western United States," and at the request of members present, Mr. Ayres gave an oral account of his new separator, which is here published as an independent paper, partly because of its inherent importance and partly because it describes an improvement which did not originate in the Western United States, and therefore does not fall, strictly speaking, under the title of President Urunton's address.—R. W. R.] A brief history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name "breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the " breaker-boy " as a slate-picker, with his ever-increasing capriciousness. As the richer veins or a splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities, particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complicatioii yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Jan 1, 1910

By Gerald M. Friedman

CONVENTIONAL usage defines emery as a natural aggregate of corundum and magnetite. Because emery bodies contain abundant spinel two types are recognized, spinel-bearing and spinel- free. Watson and Steiger1 introduced the name spinellite for emery in which spinel is a major constituuent, but this term has not been generally adopted. Spinel emery grades locally into spinel magnetite rocks with or without accessory corundum. Even this variety has been used commercially in the past. The term emery therefore applies to natural aggregates composed of corundum and magnetite; corundum, magnetite, and spinel; and spinel and magnetite.

Jan 7, 1957

ST. LOUIS SECTION H. A. BUEHLER, Chairman, CHARLES T. ORR, Vice-Chairman., THOMAS T. BREWSTER, Vice-Chairman, L. L. HUTCHISON, Vice-Chairman, W. E. McCOURT, Secretary-Treasurer, Washington University, St. Louis. CHARLES J. ADAMI, EUGENE MCAULIFFE, A. C. TERRILL, JAMES A. CASELTON, JAMES D. ROBERTSON. The annual meeting of the St. Louis Section was held at the St. Louis Club, Saturday evening, Mar. 10, 1917. Philip N. Moore, President, and Bradley Stoughton, Secretary of the Institute, were the guests of the Section. The meeting was preceded by a dinner, at which 70 were present, and was presided over by F. W. DeWolf. Addresses were made by Mr. Moore and Mr. Stoughton. The routine reports of the officers were- presented and the Executive Committee named above was elected for the current year. The special business of the meeting was a report of progress concerning the arrangements for the Institute meeting to be held in the St. Louis Section district, Oct. 8 to 13, 1917. The general program for the meeting met with the cordial approval and cooperation of the members of the Section. It was evident that the members are united in an endeavor to arrange a successful meeting. W. E. McCOURT, Secretary.

Jan 4, 1917

By John Freeman

THIS paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful development of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitable die-casting machines. The melting point of copper is 1084° C. (1983° F.) and of a high brass about 900° C. (1652° F.), as compared to 327.5° C. (621.5° F.) for lead, 419.4° C. (786.7° F.) for zinc and 658.7° C. (1217.7° F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals.

Jan 1, 1935

By P. G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the necessary information in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included: - careful checks on the sampling and assaying, - selection of representative samples used to establish the recoverable amounts of precious metals in the ore, - examination of underground workings driven to provide samples both for metallurgical testing and for assay comparison, - evaluation of plant site and waste dump areas as non-material, including a placer examination of the tailings disposal area, and location of an adequate water supply. All these investigation were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1985

By T. P. Oxford, G. Y. Onoda, E. D. Whitney

Disposal of phosphatic clay waste slurry has been a problem since the advent of hydraulic processing of phosphate rock in Florida. Alternatives to the present practice of storing slimes behind earthen dikes have been earnestly sought for more than a quarter of a century. Seepage dewatering is a promising technique intended to increase waste clay solids content to a level sufficiently high to permit clay disposal in mine cuts, in lieu of above-grade impoundment. An experimental array of vertical seepage columns containing mine tailings sand was constructed. Significant improvement in waste clay dewatering relative to that occurring in a control test was observed when approximately 1800 m3 of waste clay was disposed of in the presence of the seepage aids.

Jan 1, 1983

By Reno Sales

THE present-day application of geological knowledge to mine opera-tions owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contem-plated. And finally, out of this situation there developed the inde-pendent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1934

By Reno H. Sales

The present-day application of geological knowledge to mine operations owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contemplated. And finally, out of this situation there developed the independent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1935